Billy Goat Lawn Mower KV600 User Manual

KV Push Owner’s Manual  
BILLY GOAT KV VACUUM  
Owner's Manual  
KV600, KV650H  
Accessories  
ON BOARD  
VACUUM  
HOSE KIT  
FELT  
DEBRIS BAG  
NOZZLE WEAR  
GUARD KIT  
CASTER KIT  
SHREDDER  
KIT  
KV LINER KIT  
PROTECTIVE  
COVER  
4"(102mm) x 7'  
(2.13m)  
For vacuuming  
in hard to reach  
areas.  
For use in  
For use in  
increasing the  
life of your  
nozzle by  
protecting it from  
damage  
To allow for  
easy rolling and  
maneuverability  
on smooth  
Shreds  
leaves,  
reducing total  
volume.  
Increases the  
life of the  
housing by  
protecting it from  
damage.  
Protects the  
leaves and  
grass in dusty  
conditions.  
machine from  
the environment  
when not in use.  
surfaces.  
P/N 891125  
P/N 891126  
P/N 891127  
P/N 891128  
P/N 890209  
P/N 891134  
P/N 891136  
Part No 891013  
Form No F072508A  
1
KV Push Owner’s Manual  
SERIAL PLATE DATA  
Record the model number, serial number, date of  
purchase, and where purchased.  
Purchase Date:  
Purchased From:  
Specifications  
KV600  
KV650H  
Engine: HP  
6.0 (4.47 kW)  
6.5 (4.85kW)  
Engine: Type  
B&S Quantum  
112K020124E1  
1.5 qt. (1.4 L)  
0.63 qt. (0.6 L)  
112# (50.8kg)  
59” (1.5m)  
HONDA  
GSV190AN1L  
1.6 qt. (1.5 L)  
0.58 qt (0.54L)  
113# (51.3kg)  
59” (1.5m)  
Engine: Model  
Engine: Fuel Capacity  
Engine: Oil Capacity  
Total Unit Weight:  
Overall Length  
Overall Width  
26. 5” (0.7m)  
42.75” (1.1m)  
200  
26.5” (0.7m)  
42.75” (1.1m)  
200  
Overall Height  
Max. operating slope  
Sound in accordance with  
2000/14/EEC standards  
108 dBa  
109 dBa  
Sound at operator’s ear  
88 dBa  
89 dBa  
Vibration at operator position  
0.5 g (4.95m/s2)  
0.32 g (3.18m/s2)  
Part No 891013  
Form No F072508A  
3
KV Push Owner’s Manual  
GENERAL SAFETY INSTRUCTIONS and SYMBOLS  
The safety symbols shown below are used throughout this manual. You should become familiar with them before  
assembling, operating, or servicing this equipment.  
This symbol indicates important information that will prevent injury to yourself or others.  
This symbol indicates ear protection is recommended when operating this equipment.  
This symbol indicates eye protection is recommended when operating this equipment.  
This symbol indicates gloves should be worn when servicing this equipment.  
This symbol indicates that this manual and the engine manufacturer’s manual should be read  
carefully before assembling, operation, or servicing this equipment.  
This symbol indicates important information that will prevent damage to your BILLY GOAT ®  
KV Vacuum.  
This symbol indicates the engine oil level should be checked before operating this  
equipment.  
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or  
servicing this equipment:  
READ this manual and the engine manufacturer’s manual carefully before assembling,  
operating, or servicing this equipment.  
EAR PROTECTION is recommended when operating this equipment.  
EYE PROTECTION is recommended when operating this equipment.  
BREATHING PROTECTION is recommended when operating this equipment.  
EXHAUST from this product contains chemicals known to the State of California to cause  
cancer, birth defects or other reproductive harm.  
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land  
unless a spark arrester is installed on the muffler as required by Section 4442 of the  
California Public Resources Code. The arrester must be maintained in good working order.  
Other states may have similar laws. Federal laws apply on federal lands.  
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an  
odorless and possibly fatal poison.  
Part No 891013  
Form No F072508A  
4
KV Push Owner’s Manual  
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is  
recommended.  
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least  
two minutes before refueling.  
DO NOT store gasoline near an open flame.  
DO NOT remove gas cap while engine is running.  
DO NOT start or operate engine if strong odor of gasoline is present.  
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until  
gasoline has completely evaporated.  
DO NOT smoke while filling the fuel tank.  
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark  
tester.  
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if  
necessary. If equipped with muffler deflector, inspect deflector periodically and replace if  
necessary.  
DO NOT operate engine with grass, leaves or other combustible material near the muffler.  
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may  
cause severe burns.  
DO NOT leave equipment unattended while in operation.  
DO NOT park equipment on a steep grade or slope.  
DO NOT operate equipment with bystanders in or near the work area.  
DO NOT allow children to operate this equipment.  
DO NOT operate equipment with guards removed.  
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.  
DO NOT operate equipment on slopes greater than specified in Specifications section of this  
manual.  
DO NOT place hands or feet underneath unit, or near any moving parts.  
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.  
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.  
ALWAYS keep hands and feet away from moving or rotating parts.  
ALWAYS store fuel in approved safety containers.  
WARNING: Important  
Remove all rocks, wire, string, plastic, etc. that can present a hazard during work prior to  
starting.  
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads,  
water valves, buried cables, or clothes line anchors, etc.  
Part No 891013  
Form No F072508A  
5
KV Push Owner’s Manual  
SOUND  
SOUND LEVEL 97 dB(a) at Operator Position  
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 7-25-07 under the  
conditions listed below.  
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on  
the unit for the sound power level for your model.  
General Conditions:  
Temperature:  
Wind Speed:  
Wind Direction:  
Humidity:  
Sunny  
88oF (31.1oC)  
2 mph (3.8 kmh)  
South South East  
44%  
Barometric Pressure:  
30.07”Hg (764 mm Hg)  
VIBRATION DATA  
VIBRATION LEVEL 0.5g (4.95m/s2)  
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using  
calibrated vibration test equipment. Tests were performed on 12-20-2007 under the conditions listed below.  
General Conditions:  
Temperature:  
Wind Speed:  
Wind Direction:  
Humidity:  
Sunny  
47.5oF (8.6oC)  
3 mph (4.8kph)  
West  
87%  
Barometric Pressure:  
29.98 Hg (101.5kpa)  
INTENDED USE  
INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter.  
Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's  
primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.  
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check  
for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects.  
Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12).  
Part No 891013  
Form No F072508A  
6
KV Push Owner’s Manual  
INSTRUCTION LABELS  
The labels shown below were installed on your BILLY GOAT ® KV Vacuum. If any labels are damaged or missing, replace them before operating  
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The  
correct position for each label may be determined by referring to the Figure and Item numbers shown.  
LABEL DANGER KEEP HANDS  
AND FEET AWAY  
LABEL EAR EYE BREATHING ITEM #20  
P/N 890254  
DANGER FLYING DEBRIS  
ITEM # 19 P/N 810736  
ITEM #18 P/N 400424  
LABEL READ MANUAL  
ITEM #17 P/N 890301  
LABEL EXPLOSIVE FUEL  
ITEM # 16 P/N 400268  
DEBRIS BAG FOLDING LABEL  
LOCATED ON BAG  
ENGINE LABELS  
HONDA  
BRIGGS & STRATTON  
Read Owner’s Manual Before Operating.  
Lire le manuel d’utilisation avant la mise en route.  
Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen.  
Favor leer las instrucciones de operacion antes de operar el motor.  
Consultare il Manuale Uso e Manutenzione prima dell utilizzo.  
Las Skotselinstruktionen Innan Start.  
ENGINE CONTROLS  
Honda Throttle Control  
Briggs Throttle Control  
Part No 891013  
Form No F072508A  
7
KV Push Owner’s Manual  
PACKING CHECKLIST  
Your Billy Goat KV Vacuum is shipped from the factory in one carton, completely assembled except for the  
upper handle, debris bag, and bag quick disconnect.  
READ all safety instructions before assembling unit.  
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached by  
cables and folded over  
PUT OIL IN ENGINE BEFORE STARTING  
PARTS BAG &  
LITERATURE ASSY  
Warranty card P/N- 400972, Owner’s Manual P/N-891013, Declaration of Conformity P/N-891057, Ty-  
Wraps 900407 (qty2).  
Boxing Parts  
Checklist  
Debris Bag  
P/N-891132  
Literature Assy  
P/N-891123  
Use Ty-wraps  
here  
Connector Quick  
Disconnect  
P/N-890176  
Quick disconnect  
Honda 6.5  
GSV 190  
Briggs & Stratton  
6.0 HP Quantum  
Fig. 2  
ASSEMBLY  
1. ASSEMBLE Lift upper handle (item 11), remove items 34, 32, and 33 from lower handle (item 10). Attach and  
secure upper handle as shown using same hardware. Then use the two ty-wraps to secure the height adjust cable  
and the throttle cable at the bend on the upper handle  
2. UNFOLD the debris bag (item 21) and fasten bag neck to bag quick disconnect (item 12). Attach firmly to  
housing exhaust (item 1) see fig. 2.  
3. ATTACH bag hanger strap to bag supports (item 13), preassembled to upper handle.  
4. CONNECT spark plug wire.  
Part No 891013  
Form No F072508A  
8
KV Push Owner’s Manual  
OPERATION  
Like all mechanical tools, reasonable care must be used when operating machine.  
Inspect machine work area and machine before operating. Make sure that all operators of this  
equipment are trained in general machine use and safety.  
PUT OIL IN ENGINE BEFORE STARTING  
STARTING  
ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine  
must be level when checking and filling oil and gasoline.  
ENGINE SPEED: Controlled by throttle lever on the engine. Under normal conditions, operate at minimum  
throttle to accomplish your current cleaning task.  
CHOKE: Briggs-Located on engine and must be controlled manually.  
Honda-Place remote throttle in choke position  
PRIMER: Push primer per engine instructions (B&S only).  
THROTTLE: Move throttle to fast/choke position. Located on handle.  
IF YOUR UNIT FAILS TO START:  
See Troubleshooting on page 12.  
HANDLING & TRANSPORTING:  
This unit requires two people to lift it. Lift holding the lower handle and the front wheels. Secure  
the machine in place during transport. See page 3 for weight specifications  
Never lift the machine while the engine is running.  
STORAGE  
Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach  
an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.  
If engine is to be unused for 30 days or more, prepare as follows:  
Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and  
causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be  
sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline.  
Part No 891013  
Form No F072508A  
9
KV Push Owner’s Manual  
OPERATION  
VACUUMING OPERATION  
VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pushing slightly downward on handle  
to reduce tension on the adjuster, and then pulling height adjust trigger on the handle (item 23) up at right rear of  
machine. Then select the desired height that fits the task.  
FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE:  
Never bury nozzle into debris.  
CLEARING A CLOGGED NOZZLE & EXHAUST: Turn engine off and wait for impeller to stop completely  
and disconnect spark plug wire. Wearing durable gloves, remove clog. DANGER the clog may contain sharp  
materials. Reconnect spark plug wire.  
DEBRIS BAG  
Debris bags are normal replaceable wear items.  
Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.  
An optional felt bag is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories  
shown on page 1).  
DO NOT place bag on or near hot surface, such as engine. Be sure engine has come to a complete stop before removing or  
emptying bag.  
This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings  
page 4-5).  
However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.  
Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your  
machine's ability to vacuum in dusty conditions:  
• Run machine at idle to quarter throttle.  
• The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup  
performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake  
bag free of dust.  
• Pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use.  
NOTE: Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.  
DO NOT leave debris in bag while in storage.  
Part No 891013  
Form No F072508A  
10  
KV Push Owner’s Manual  
COMPOST  
Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to  
provide enriched soil for later use as fertilizer in gardens and flower beds  
NOTE: Allow green chips to dry before spreading around living plants.  
MAINTENANCE  
PERIODIC MAINTENANCE  
Periodic maintenance should be performed at the following intervals:  
Maintenance Operation  
Every Use (daily)  
Every 5 hrs (daily)  
Every 25 Hours  
z
Inspect for loose, worn or damaged parts.  
Clean Debris bag  
z
z
Check bag strap tightness  
Engine (See Engine Manual)  
Check for excessive vibration  
z
IMPELLER REMOVAL  
1. Wait for engine to cool and disconnect spark plug.  
2. Drain fuel and oil from the engine.  
3. Remove bag, quick release, and upper handle. Do not kink, stretch, or break control cables, control  
housings, or end fittings while removing handles.  
4. Remove housing top plate by removing bolts around outside of housing.  
5. Leaving engine fastened to top plate, turn it upside down so the impeller is on top.  
6. Remove impeller bolt and lock washer and washer.  
7. Lift impeller upward. If impeller slides freely, proceed to (step 10).  
8. Place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it  
loosens. Using a penetrating oil can help loosen a stuck impeller.  
9. If the impeller does not loosen, use two pry bars and pull the impeller near the hub away from the engine,  
this should loosen it and allow you to remove the impeller from shaft. Using a penetrating oil can help loosen a  
stuck impeller.  
10. Using a new impeller bolt and lockwasher and washer, reinstall new impeller in reverse order.  
11. Tighten impeller bolt. Torque impeller bolt to 33-38 Ft. Lbs. (44-51 N.m) (see item 30 on page 15).  
12. Reinstall engine onto housing in reverse order of removal.  
13. Gas and oil.  
14. Reinstall spark plug wire.  
Part No 891013  
Form No F072508A  
11  
KV Push Owner’s Manual  
Troubleshooting  
Problem  
Possible Cause  
Solution  
Abnorm al vibration.  
· Loose or out of balance im peller or  
loose engine  
· Check im peller and replace if required.  
Check engine  
W ill not vacuum or has poor · dirty debris bag. Hose kit cap m issing.  
· Clean debris bag. Shake bag clean or  
wash. Check for hose kit cap. Unclog  
nozzle or exhaust. Allow air to feed with  
debris  
· Check stop switches, throttle, choke  
position and gasoline. Connect spark  
vacuum perform ance  
Engine will not start.  
·Clogged nozzle or exhaust. Excessive  
quantity of debris.  
· Im proper nozzle height  
· Stop switch off. Throttle in off position.  
Engine not in full choke position. O ut of  
gasoline. Bad or old gasoline. Sparkplug plug wire. Clean or replace air filter. O r  
wire disconnected. Dirty air cleaner  
contact a qualified service person.  
Engine is locked, will not pull · Debris locked in im peller. Engine  
· See page 5. Contact a engine service  
dealer for engine problem s  
Adjust nozzle height (See Nozzle height  
fine adjustm ent for hard surfaces on  
page 5  
over.  
problem .  
Nozzle scrapes ground in  
lowest height setting.  
Nozzle height out of adjustm ent  
Too m uch dust com ing from  
bag.  
· Vacuum ing very dry, brittle or sm all  
debris  
· Switch to felt bag (see page 1  
accessories)  
When servicing engine refer to specific manufacturers engine owner's manual. Engine warranty is covered by the  
specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing  
engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available  
for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the  
manufacturers national service organization.  
To reach:  
American Honda: 800-426-7701  
Briggs & Stratton: 800-233-3723  
WARRANTY CLAIM PROCEDURE  
®
Should a BILLY GOAT machine fail due to a defect in material and/or workmanship, the owner should make a  
warranty claim as follows:  
The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY  
GOAT Dealer.  
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the  
invoice or receipt.  
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their  
respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under  
warranty must be tagged and retained for 90 days. The model number and serial number of the unit must  
be stated in the Warranty Claim.  
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.  
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be  
returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from  
whom the claim was received.  
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is  
final and binding.  
For online product registration go to www.billygoat.com  
Part No 891013  
Form No F072508A  
12  
KV Push Owner’s Manual  
MAINTENANCE RECORD  
Date  
Service Performed  
Part No 891013  
Form No F072508A  
13  
KV Push Owner’s Manual  
PARTS DRAWING KV  
Part No 891013  
Form No F072508A  
14  
KV Push Owner’s Manual  
PARTS LIST  
* Denotes  
ITEM  
NO.  
KV600 PART  
KV650H PART  
NUMBER  
DESCRIPTION  
QTY  
QTY  
standard  
hardware  
item that  
may be  
purchased  
locally.  
NUMBER  
891100-S  
891110-S  
891103  
1
2
3
4
5
MAIN FRAME HOUSING NEW KD  
NOZZLE ASSEMBLY TKV  
1
1
1
1
1
891100-S  
891110-S  
891103  
1
1
1
1
1
AXLE FRONT WA NEW KD  
PLATE TOP ENGINE KV  
891007-1-S  
891108-S  
891007-1-S  
891108-S  
IMPELLER 12.75 WA PUSH VAC  
6
DOOR EXHAUST ASSY RAW  
890148  
1
890148  
1
7
8
9
WASHER 1/2" SAE Z/P  
WHEEL ASSY 12" X 2.5" TREAD  
ENGINE 6.5 HP HONDA GSV190AN1L  
ENGINE 6.0 HP B&S  
8172011  
900509  
-
4
4
-
8172011  
900509  
840069  
-
4
4
1
-
890622  
891050  
891054-S  
890176  
520120  
360279  
430342  
400268  
890301  
400424  
810736  
890254  
891132  
891036  
891001  
900407  
8177012  
9201080  
1
1
1
1
4
4
2
1
1
2
1
1
1
1
1
3
1
1
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
23  
25  
26  
27  
28  
LOWER HANDLE KV  
891050  
891054-S  
890176  
520120  
360279  
430342  
400268  
890301  
400424  
810736  
890254  
891132  
891027  
891001  
900407  
8177012  
9201080  
1
1
1
4
4
2
1
1
2
1
1
1
1
1
3
1
1
HANDLE UPPER KV  
QUICK DISCONNECT  
PIN CLEVIS 3/8" x 2.125" LONG  
RETAINER  
GRIP HANDLE 1"X 9.5" LG  
LABEL HOT ENGINE  
LABEL READ  
LABEL WARNING DANGER  
LABEL DANGER FLYING DEBRIS  
LABEL EAR EYE BREATHING  
BAG DEBRIS NO ZIPPER KV  
CABLE THROTTLE ASSY 42" W/CHOKE  
CABLE HGT ADJ TRIGGER KV  
TY WRAP  
WASHER LOCK 3/8" ST MED  
KEY 3/16 SQ. X 1.25  
29  
30  
SCREW MACHINE #10-24 X 1 1/2" HWF ZP  
891042  
1
891042  
1
SCREWCAP 3/8-24X1 LOCKTITE  
SCREWCAP 3/8-24X1 1/2" GR. 8  
SCREWCAP 1/4 - 20 x 5/8 HWH  
WASHER 5/16 FLATWASHER Z/P  
SCREWCAP 5/16-18 X 1.75 ZP  
NUT LOCK 5/16-18  
900154  
-
1
-
-
-
1
900344  
890359  
8171003  
8041031  
8160002  
8041004  
8172007  
8160001  
890530  
8041011  
891039  
890408  
891002  
891003  
900146-01  
891043  
891045  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
890359  
8171003  
8041031  
8160002  
8041004  
8172007  
8160001  
890530  
8041011  
891039  
890408  
891002  
891003  
900146-01  
891043  
891045  
16  
18  
8
16  
18  
8
8
8
SCREWCAP 1/4-20 X 3/4"  
WASHER 1/4" SAE ZP  
2
2
10  
9
10  
9
NYLON INSERT LOCKNUT, 1/4-20 UNC  
1/2-13 CAP NUT NP W/PATCH  
SCREWCAP 1/4-20x2.25x0.75-N  
SCREW PLASTIC 1/4-10 X 1  
SCREW 3/8 x 1 1/2 TAPTITE  
NOZZLE TOP HALF KV  
4
4
1
1
8
8
3
3
1
1
NOZZLE BOTTOM HALF KV  
PLUG HOUSING KD LB  
1
1
1
1
SCREW SELF TAPPING 10-24 X 1/2  
LABEL KV PUSH  
1
1
1
1
47  
48  
49  
50  
51  
SCREWCAP 1/4-20 X 1"  
8041006  
891062  
891064  
-
6
1
1
-
8041006  
891062  
891064  
840083  
440153  
6
1
1
2
1
KV REINFORCEMENT NOZZLE BRACKET LFT  
KV REINFORCEMENT NOZZLE BRACKET RT  
SPACER 1.50 OD X .890 ID X .50 THK  
WASHER 1.5 OD X .453 ID X .25 THK  
440153  
1
Part No 891013  
Form No F072508A  
15  
KV Push Owner’s Manual  
BRUSH CUTTER  
FORCE BLOWER  
AERATOR  
If you liked this product please feel  
free to view our full line of quality lawn  
care, renovation, and debris removal  
DL VACUUM  
MULTI VACUUM  
POWER RAKE  
Part No 891013  
Form No F072508A  
16  

Craftsman Lawn Mower 91725354 User Guide
Craftsman Lawn Mower Accessory 48624621 User Guide
Dixon Lawn Mower 16463 106 User Guide
Husqvarna Lawn Mower YTH2242TDF User Guide
Poulan Lawn Mower 177545 User Guide
Poulan Lawn Mower Accessory 140603 User Guide
Snapper Lawn Aerator 4570 User Guide
Snapper Lawn Mower E250815BE User Manual
Stiga Lawn Mower 12 4301 22 User Guide
Stiga Lawn Mower 8211 0072 80 User Guide