Honda Automobiles Automobile Accessories User Manual

Accessory  
Application  
Publications No.  
All 21624  
2001 ACCORD  
2- AND 4-DOOR  
(INCLUDES V6)  
INSTALLATION  
INSTRUCTIONS  
SECURITY SYSTEM  
Issue Date  
AUG 2000  
PARTS LIST  
Security System Attachment (sold separately):  
P/N 08E55-S84-100  
Security System (sold separately):  
P/N 08E51-S84-100  
Security system  
wire harness  
2 Remote controls  
Control unit  
Sub-harness  
LED  
White connector clip  
Control unit bracket  
Push nut  
2-Pin connector (for LED)  
2 Relay brackets  
5 Short wire ties  
Disarm switch  
Window decal  
3-Pin connector  
(for disarm switch)  
3 Washer bolts, 6 x 1
Ground bolt  
Nut, 12 mm  
Washer  
Owner’s Manual  
3 Flange nuts, 6 mm  
3 Self-tapping screw
2 Washer-screws, 4 x 30 mm  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
Y0581-A  
1 of 12  
08E55-S84-1000-91  
Adjusting the Control Unit  
INSTALLATION  
Use a small flat-tip screwdriver to change the  
mode switch and the horn/siren switch and to  
adjust sensitivity.  
Customer Information: The information in this  
installation instruction is intended for use only by  
skilled technicians who have the proper tools,  
equipment, and training to correctly and safely add  
equipment to your car. These procedures should not  
be attempted by "do-it-yourselfers."  
GLASS BREAKAGE  
SENSOR  
MODE SWITCH  
1. Make sure you have the anti-theft code for the  
radio, then write down the frequencies for the  
preset buttons.  
AUTO LOCK  
AUTO  
MANUAL  
SENSITIVITY  
ADJUSTMENT  
KNOB  
2. Disconnect the negative cable from the battery.  
3. Inside the passengers compartment, remove the  
MAX  
MIN  
front console lower cover (four retaining clips).  
SIREN  
HORN  
HORN/SIREN  
SWITCH  
FRONT CONSOLE  
LOWER COVER  
Mode Switch:  
Set the mode switch according to the customers  
CLIP  
choice.  
If the vehicle youre working on is equipped with an  
optional ashtray with cigarette lighter, continue with  
step 4, if not go to step 5.  
Refer to the Owners Manual for the explanation of  
each mode.  
Horn/Siren Switch:  
4. Remove the ashtray with cigarette lighter, (two  
self-tapping screws, one connector, and four  
retaining clips).  
Set the switch to HORNin normal use. If an optional  
siren is installed, set the switch to SIREN.”  
Glass Breakage Sensor:  
ASHTRAYWITH  
CIGARETTE LIGHTER  
Do not attach anything like scotch tape over the  
holes; this is the microphone pickup.  
Sensitivity Adjustment Knob:  
Adjust the sensitivity only if the customer requests  
it; the sensitivity adjustment of the glass breakage  
sensor is factory set.  
CONNECTOR  
Be careful when you adjust the sensitivity; if you  
raise the sensitivity too much, the security system  
can give a false alarm, and if the sensitivity is too  
low, the security system may not work even if  
glass is broken.  
SELF-TAPPING  
SCREWS  
CLIP  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
All 21624 (0008)  
3 of 12  
5. Remove the left fuse box cover (three retaining  
clips and two tabs).  
7. Remove the drivers door sill molding (four clips).  
CLIP  
TAB  
CLIP  
DRIVER'S DOOR  
SILL MOLDING  
LEFT FUSE  
LEFT FUSE  
BOX COVER  
BOX  
TAB  
CLIP  
RETAINING  
CLIPS  
6. Remove the driver's dashboard lower cover (three  
screws, and five retaining clips).  
8. Remove the kick panel (two clips, and pull).  
SCREW  
KICK PANEL  
SCREW  
SCREW  
DRIVER'S  
DASHBOARD  
LOWER COVER  
CLIP  
CLIP  
4 of 12  
All 21624 (0008)  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
9. Remove the right fuse box cover (three retaining  
clips and two tabs).  
11. Open the glove box, and remove the two screw  
caps and seven self-tapping screws. Unplug the  
connector, and remove the glove box by pulling it  
toward you.  
GLOVE BOX  
TAB  
CLIP  
CONNECTOR  
SELF-TAPPING  
SCREW  
CAPS  
RIGHT FUSE  
BOX COVER  
RIGHT FUSE  
BOX  
TAB  
12. Lower the steering wheel tilt lever. Remove the  
upper and lower steering column covers (three  
screws, six tabs, and one harness clip). Gently  
push on the six retaining tabs, and separate the  
two steering column covers.  
10. Remove the passengers dashboard lower cover  
(three screws and seven retaining clips).  
GLOVE BOX  
UPPER  
STEERING  
COLUMN COVER  
TABS  
(Push.)  
TABS  
(Push.)  
STEERINGWHEEL  
TILT LEVER  
SCREW  
SCREW  
LOWER  
STEERING  
COLUMN  
SCREW  
PASSENGER'S  
DASHBOARD  
LOWER COVER  
COVER  
Push  
CLIP  
TAB  
SCREWS  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
All 21624 (0008)  
5 of 12  
13. Measure and mark the upper steering column  
cover.  
16. Locate the 2-pin connector included in the kit, and  
lower the lock. Firmly push the LED terminals into  
the 2-pin connector.  
Insert.  
Lock.  
5.5 mm  
DRILL  
UPPER STEERING  
COLUMN COVER  
WHITEWIRE  
20 mm  
REDWIRE  
17. Measure and mark the driver's dashboard lower  
cover. (If necessary, remove the insulation.)  
MARK  
14. While wearing eye protection, lightly center-punch  
the mark; then drill a 5.5 mm hole through the  
upper steering column cover. Remove all burrs.  
First drill with a  
10 mm bit, then with  
a 12 mm drill bit.  
15. Route the terminal ends of the LED through the  
hole you just drilled, and secure the LED with the  
push nut. Install the push nut securely.  
MARK  
LED  
BACK OF  
DRIVER'S  
25 mm  
DASHBOARD  
LOWER COVER  
UPPER STEERING  
COLUMN COVER  
15 mm  
18. While wearing eye protection, lightly center-punch  
the mark; then drill a 12 mm hole through the  
center-punched mark.  
First drill a pilot hole with a 10 mm bit, then  
finish with a 12 mm bit.  
PUSH NUT  
Remove all burrs.  
PUSH NUT  
6 of 12  
All 21624 (0008)  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
19. Route the terminal ends of the disarm switch  
through the hole you just drilled, and secure it with  
the washer and 12 mm nut from the kit.  
21. Push the wire tie with clip into the hole in the back  
of the control unit bracket. Position the control unit  
bracket on the driver's dashboard lower cover, and  
install the three self-tapping screws from the  
attachment kit.  
NUT  
SELF-TAPPING  
SCREW  
WASHER  
WIRE TIE  
WITH CLIP  
DRIVER'S  
DASHBOARD LOWER  
COVER  
CONTROL  
UNIT  
BRACKET  
DISARM SWITCH  
BACK OF DRIVER'S  
DASHBOARD  
LOWER COVER  
20. Locate the 3-pin connector included in the kit.  
Firmly push the disarm switch terminals into the  
3-pin connector until they click into position, and  
lower the lock. Slide the white connector clip onto  
the underside of the 3-pin connector.  
22. Position the control unit on the control unit bracket,  
and install the two 4 x 30 mm washer-screws.  
Secure the antenna to the control unit bracket with  
the wire tie with clip you just installed, as shown.  
Secure the antenna parallel with the control unit.  
3-PIN  
CONNECTOR  
Lock.  
4 x 30 mm  
WASHER-SCREW  
Insert.  
WHITE  
CONNECTOR  
CLIP  
CONTROL  
UNIT  
ANTENNA  
BLUEWIRE  
CONTROL UNIT  
BRACKET  
BLACKWIRE  
WIRE TIE WITH CLIP  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
All 21624 (0008)  
7 of 12  
23. Secure the disarm switch wire harness to the  
disarm switch with one short wire tie, then attach  
the harness to the driver's dashboard lower cover  
with two halves of a cushion tape in the areas  
shown. (Cut a cushion tape in half with scissors,  
and use the two halves to secure the harness.)  
26. Attach the 14-pin connector of the security system  
wire harness to the side of the vehicle connector.  
LEFT FUSE BOX  
SECURITY SYSTEM  
WIRE HARNESS  
14-PIN CONNECTOR  
CONNECTOR  
CLIP  
DISARM SWITCH  
SHORT  
WIRE TIE  
CONTROL  
UNIT  
BRACKET  
VEHICLE  
CONNECTOR  
CUSHIONTAPE  
(Cut in half.)  
27. Locate the two 2-pin connectors blue-taped to the  
vehicle harness, and remove the blue tapes to free  
the connectors. Plug the 2-pin connectors you just  
freed into the 2-pin connectors of the security  
system wire harness. Connect the blue 2-pin  
connector of the vehicle harness to the blue 2-pin  
connector of the security system wire harness.  
24. Push the clip on the 3-pin connector of the disarm  
switch into the hole in the control unit bracket.  
25. From the driver's side, route the 14-pin connectors  
of the security system wire harness to the left fuse  
box. Unplug the 14-pin connector from the fuse  
box, and plug the 14-pin connectors of the security  
system wire harness in between.  
LEFT FUSE BOX  
LEFT FUSE  
BOX  
2-PIN  
CONNECTORS  
(GRAY)  
SECURITY SYSTEM  
WIRE HARNESS  
SECURITY  
SYSTEM  
WIRE  
HARNESS  
2-PIN  
CONNECTORS  
(BLUE)  
14-PIN CONNECTOR  
(VEHICLE HARNESS)  
14-PIN CONNECTORS  
(SECURITY SYSTEM  
WIRE HARNESS)  
8 of 12  
All 21624 (0008)  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
28. Remove the upper bolt that fastens the engine  
hood opener, and attach the ground terminal of the  
security system wire harness with the ground bolt  
from the kit.  
31. Unplug the 20-pin connector from the left fuse box,  
and plug the two 20-pin connectors (white) of the  
security system wire harness in between.  
VEHICLE  
20-PIN  
CONNECTOR  
1-PIN CONNECTOR OF  
SECURITY SYSTEMWIRE  
LEFT  
FUSE  
BOX  
No. 5  
CONNE
OF FUS
ENGIN
OPENE
20-PIN CONNECTORS  
SECURITY SYSTEM  
BOLT  
OF SECURITY SYSTEM  
WIRE HARNESS  
WIRE HARNESS  
ENGINE HOOD  
GROUNDTERMINAL OF  
OPENER MOUNT BOLT  
SECURITY SYSTEM  
(Discard.)  
WIRE HARNESS  
32. Locate the 2-pin connector blue-taped to the  
vehicle harness 18-pin connector, and remove the  
blue tape to free the connector. Connect the 2-pin  
connector you just freed to the 2-pin connector of  
the security system wire harness.  
29. Plug the 1-pin connector (white) of the security  
system wire harness into the No. 5 connector of  
the fuse box.  
30. Under the dashboard at the fuse box, locate the  
4-pin connector blue-taped to the vehicle harness  
(22-pin connector), and remove the blue tape to  
free the connector. Connect the 4-pin connector  
you just freed to the 4-pin connector (C) of the  
security system harness.  
BLUETAPE  
(Remove.)  
VEHICLE  
18-PIN CONNECTOR  
VEHICLE  
2-PIN CONNECTOR  
VEHICLE  
22-PIN CONNECTOR  
LEFT  
FUSE  
BOX  
BLUETAPE  
(Remove.)  
LEFT  
FUSE  
BOX  
4-PIN  
CONNECTOR OF  
2-PIN CONNECTOR OF  
SECURITY SYSTEM  
WIRE HARNESS  
SECURITY  
SYSTEM WIRE  
HARNESS  
(WHITE)  
SECURITY SYSTEM  
WIRE HARNESS  
SECURITY SYSTEM  
WIRE HARNESS  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
All 21624 (0008)  
9 of 12  
33. Remove the clip from the hole in the left knee  
bolster, use a utility knife to cut the clip off of the  
vehicle harness. Take care not to damage the  
vehicle harness.  
37. Position the 5-pin and 4-pin relays onto the other  
relay bracket, and install one 6 x 12 mm  
washer-bolt and 6 mm nut.  
RELAY BRACKET  
LEFT KNEE  
BOLSTER  
6 mm  
FLANGE  
NUT  
6 x 12 mm  
WASHER-BOLT  
4-PIN RELAY  
About 45°  
VEHICLE  
HARNESS  
5-PIN RELAY  
HARNESS CLIP  
(Cut and discard.)  
34. Assemble three fuse cases as shown. Attach the  
appropriate fuse label to each fuse case of the  
security system wire harness, then attach the red  
connector clip as shown.  
5-PIN RELAY  
38. Plug the 6-pin and 4-pin connectors of the security  
system wire harness into the 5-pin and 4-pin  
RED  
relays; then attach the relay bracket to the steering  
hanger beam with one 6 x 12 mm washer-bolt and  
6 mm flange nut. (The 5-pin relay has a 6-pin  
CONNECTOR  
CLIP  
FUSE SEAL  
(15 A)  
FUSE SEAL  
(3 A)  
connector.)  
5-PIN RELAY  
4-PIN  
RELAY  
LEFT  
KNEE  
BOLSTER  
6 x 12 mm  
WASHER-BOLT  
RELAY  
BRACKET  
FUSE  
CASE OF  
SECURITY  
SYSTEM  
WIRE  
HARNESS  
4-PIN  
CONNECTOR  
6-PIN CONNECTOR  
5-PIN  
RELAY  
6 mm  
FLANGE NUT  
LONG  
WIRE TIE  
6 mm  
FLANGE  
NUT  
VEHICLE HARNESS  
35. Position one of the relay brackets on the left knee  
bolster, and install one 6 x 12 mm washer-bolt and  
6 mm flange nut. Push the red connector clip on  
the fuse case of the security system wire harness  
into the hole in the relay bracket.  
4-PIN  
RELAY  
6 x 12 mm  
WASHER-  
BOLT  
36. Secure the security system wire harness to the  
vehicle harness with one long wire tie in the area  
shown.  
STEERING HANGER BEAM  
10 of 12  
All 21624 (0008)  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
39. Route the 2-pin connector of the LED through the  
lower steering column cover, and connect it to the  
2-pin connector of the security system wire  
harness. Reinstall the lower and upper steering  
column covers.  
41. On the left of the steering wheel, secure the  
security system wire harness to the vehicle  
harness with three long wire ties in the areas  
shown.  
LONGWIRE  
TIES  
UPPER  
STEERING  
COLUMN  
COVER  
LED  
LED HARNESS  
LEFT FUSE  
BOX  
LOWER  
STEERING  
COLUMN  
COVER  
VEHICLE  
HARNESS  
SECURITY SYSTEM  
2-PIN  
CONNECTORS  
WIRE HARNESS  
SECURITY SYSTEM  
WIRE HARNESS  
42. On the left of the fuse box, secure the security  
system wire harness to the vehicle harness with  
two long wire ties.  
40. Secure the security system wire harness and the  
LED 2-pin connector to the vehicle harness with  
three long wire ties and one short wire tie. Secure  
the wire ties only in the areas shown and not to the  
yellow SRS harness.  
LEFT FUSE  
BOX  
LED 2-PIN  
CONNECTOR  
SHORT  
WIRE TIE  
LONGWIRE  
TIES  
LONG  
WIRE  
TIES  
SECURITY SYSTEM  
WIRE HARNESS  
VEHICLE HARNESS  
VEHICLE  
HARNESS  
SECURITY SYSTEM  
WIRE HARNESS  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  
All 21624 (0008)  
11 of 12  
43. Plug the 3-pin connector of the security system  
wire harness into the 3-pin connector of the disarm  
switch harness. Plug the 22-pin connector of the  
security system wire harness into the control unit;  
then reinstall the driver's dashboard lower cover.  
46. Route the sub-harness along the vehicle harness.  
Inside the glove box, locate the 2-pin connector  
blue-taped to the vehicle harness, and remove the  
blue tape to free the connector. Plug the 2-pin  
connector of the sub-harness into the 2-pin  
connector you just freed.  
SECURITY SYSTEMWIRE HARNESS  
22-PIN CONNECTOR  
BLUETAPE  
2-PIN  
(Remove.)  
CONNECTOR  
H  
OR  
VEHICLE  
HARNESS  
SUB-  
HARNESS  
CONTROL UNIT  
DRIVER'S  
SHORT  
WIRE TIES  
DASHBOARD  
SECURITY SYSTEMWIRE  
LOWER COVER  
HARNESS 3-PIN  
CONNECTOR  
47. Secure the sub-harness to the vehicle with three  
short wire ties.  
48. Open the hood, and attach the cover on the  
bulkhead center stay.  
44. Unplug the 4-pin connector from the right fuse box  
and plug the 4-pin connector of the sub-harness  
there.  
VEHICLE  
4-PIN CONNECTOR  
HOLE IN  
INNER  
LOWER  
PILLAR  
BULKHEAD  
CENTER STAY  
COVER  
49. Check that all wire harnesses are routed properly  
and all connectors are plugged in.  
50. Reinstall all removed parts.  
SUB-HARNESS  
4-PIN CONNECTOR  
SUB-HARNESS  
51. Reconnect the negative cable to the battery.  
45. Push the clip of the sub-harness 4-pin connector  
into the hole in the right front inner lower pillar.  
52. Enter the customers radio anti-theft code, if  
applicable, and reset the radio station presets.  
53. Reset the clock.  
54. Check operation of the security system according  
to the Owners Manual supplied.  
12 of 12  
All 21624 (0008)  
© 2000 American Honda Motor Co., Inc - All Rights Reserved.  

Brother FAX 1840CN User Manual
Carrier 39LC User Manual
Epson S30670 User Manual
Fisher Price P7866 User Manual
Friedrich Air Conditioner R 410A User Manual
Friedrich MW18C3F User Manual
Friedrich SS08M10 User Manual
Frigidaire FSC24CH8M User Manual
Honda Power Equipment GCV530 User Manual
HP Hewlett Packard LASERJET 2400 User Manual