Accessory
Application
Publications No.
AII 30556
AUTOMATIC DAY/NIGHT
MIRROR
INSTALLATION
INSTRUCTIONS
2005-2006 CR-V
Issue Date
ATTACHMENT KIT
SEP 2005
PARTS LIST
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
10 mm Combination wrench
Ratchet
Automatic Day/Night Mirror Attachment Kit
(sold separately)
P/N 08V03-S9A-101
Upper and lower covers
8 mm, 10 mm and 14 mm Sockets
T20 and T25 Torx bits
Diagonal cutters
Clip
Torque wrench
Isopropyl alcohol
Shop towel
Piece of steel wire
Tape measure
Day/night mirror harness
Scissors
Electrical tape
Pliers
Mirror harness
10 Wire ties
Illustration of the Day/Night Mirror Installed on
the Vehicle
MIRROR
HARNESS
DAY/NIGHT
MIRROR
2 EPT sealer
Ground bolt
FUSE CASE
(2A)
DAY/NIGHT
MIRROR
HARNESS
Automatic Day/Night Mirror Kit
(sold separately)
P/N 08V03-S9A-100B
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
Day/Night mirror
1. Make sure you have the anti-theft code for the radio,
then write down the radio station presets.
Owner’s Manual
2. Disconnect the negative cable from the battery.
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
AII 30556 (0509)
08V03-S9A-1000-91 1 of 10
7. Remove the cap from the right sunvisor (four
retaining tabs).
10. Remove the passenger’s dashboard under cover
(release the three clips and two pins.)
CLIPS (3)
RETAINING
TABS (4)
PASSENGER’S
DASHBOARD
UNDER COVER
CAP
PINS (2)
RIGHT
SUNVISOR
TORX SCREW
11. Open the glove box. Release the right and left
stops.
8. Remove the right sunvisor (two T25 Torx screws).
TABS (2)
9. Remove the door opening weatherstrip from the
right front pillar in the area shown. Remove the
right front pillar trim (2 clips).
STOPS (2)
CLIP
Pull out part way
to release.
CLIP
GLOVE
BOX
DOOR OPENING
WEATHERSTRIP
SCREW
12. Remove the two screws from the bottom of the
glove box, and remove the glove box.
RIGHT FRONT
PILLAR TRIM
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
AII 30556 (0509)
3 of 10
13. Remove the right kick panel (pull to release the
two clips).
15. Remove the driver’s dashboard lower cover:
•
•
•
Remove the fuse box lid, and open the pocket.
Remove the two self-tapping screws.
RIGHT KICK
PANEL
Gently pull out on the driver’s dashboard lower
cover to release the eight clips. If equipped,
unplug the vehicle connector and remove the
lower cover.
TAB
VEHICLE CONNECTOR
VEHICLE CONNECTOR
(If equipped.)
(If equipped.)
DRIVER’S
DASHBOARD
LOWER
COVER
TAB
CLIP
POCKET
HOOKS (2)
14. Turn the knob clockwise, and remove the driver’s
dashboard under cover (one clip).
FUSE
BOX
LID
HOLDER
SELF-TAPPING
SCREW
RETAINING
TABS (2)
CLIP
CLIPS (8)
16. Open the dashboard pocket lid. Using a flat-tip
screwdriver wrapped with tape, remove the screw
cover by releasing the two retaining clips and two
retaining tabs. Remove the dashboard pocket (one
self-tapping screw, then pull out to release the one
clip and three retaining tabs). If equipped, unplug
the vehicle connector.
KNOB
Turn
clockwise
CLIP
DASHBOARD
POCKET
RETAINING TAB
DRIVER’S
DASHBOARD
90°.
UNDER COVER
CLIP
SELF-
TAPPING
SCREW
SCREW
COVER
TAPE
VEHICLE
CONNECTOR
(If equipped)
RETAINING
TABS (2)
SMALL
FLAT-TIP
SCREWDRIVER
RETAINING TABS (2)
4 of 10
AII 30556 (0509)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
17. Remove two self-tapping screws that fasten the
heater A/C control panel to the dashboard. Pull
the heater A/C control panel out toward you to
release the four clips. Unplug the vehicle
connector, and remove the heater A/C control
panel.
19. On M/T vehicles only, remove the four seat track
end covers from the driver’s seat, then remove the
four bolts that secure the seat.
SEAT TRACK
END COVERS (4)
DRIVER’S
SIDE SEAT
SELF-TAPPING
SCREW
HEATER A/C
CONTROL
PANEL
VEHICLE
CONNECTOR
BOLTS (4)
CLIPS (4)
20. On M/T vehicles only, pull the shift boot down
while holding the plastic clip. Remove the shift
knob from the shift lever by turning it
counterclockwise.
18. On A/T vehicles only, remove the two clips and
six self-tapping screws, and pull the dashboard
center lower cover out toward you to release the
six clips. Unplug the vehicle 2-pin connector from
the accessory socket, then remove the cover.
PLASTIC
CLIP
SELF-
TAPPING
SCREWS (6)
VEHICLE 2-PIN
CONNECTOR
SHIFT BOOT
Pull down
SHIFT KNOB
Turn
counterclockwise
to remove.
DASHBOARD
CENTER
LOWER
COVER
Pull toward you.
CLIPS (2)
CLIPS (4)
CLIP
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
AII 30556 (0509)
5 of 10
21. On M/T vehicles only, remove the two side covers
(four tabs) from the center console.
23. Slide the day/night mirror stay onto the mirror
holder, then tighten the T20 Torx screw installed on
the day/night mirror.
VEHICLE 2-PIN
CONNECTOR
CLIP
TORX
SCREW
ILLUMINATION
BULB
Pull
SIDE COVER
MIRROR
HOLDER
TABS (4)
MIRROR
STAY
CLIPS (2)
DAY/NIGHT
MIRROR
FRONT
CONSOLE
TABS (4)
SIDE
COVER
CLIPS (2)
SELF-TAPPING
SCREWS (7)
24. Plug the mirror harness 7-pin connector into the
rear of the mirror, then route the 4-pin connector
up and out through the console opening in the
roof lining as shown.
22. On M/T vehicles only, remove the two clips and
seven self-tapping screws, and pull the front
console out toward you to release four clips.
Unplug the vehicle 2-pin connector from the
accessory socket, then remove the front console.
CONSOLE OPENING
IN ROOF LINING
ROOF LINING
MIRROR
HARNESS
MIRROR
HARNESS
4-PIN
CONNECTOR
MIRROR HARNESS
7-PIN CONNECTOR
DAY/NIGHT
MIRROR
6 of 10
AII 30556 (0509)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
25. Route the mirror harness through the grooves of
the upper and lower covers. Attach the lower
cover to the stay of the mirror.
28. Unplug the vehicle 21-pin connector (white) and
connect the day/night mirror harness 21-pin
connectors between the vehicle 21-pin
connectors (white).
MIRROR
HARNESS
ROOF LINING
LOWER
COVER
VEHICLE 21-PIN
CONNECTOR (white)
DAY/NIGHT
MIRROR STAY
UPPER
AND
LOWER
COVERS
DAY/NIGHT
MIRROR
26. Slide the upper cover up and under the roof lining
as shown.
DAY/NIGHT MIRROR
HARNESS 21-PIN
CONNECTOR
27. Unplug the vehicle connectors (gray) and
disengage the clip installing the vehicle 21-pin
connector (white) to the right center frame.
DAY/NIGHT MIRROR
HARNESS
29. Remove the connector clip from the vehicle 21-pin
connector (white) and install the new clip supplied
with the kit onto the vehicle 21-pin connector.
CLIP
VEHICLE 21-PIN
CONNECTOR
(white)
RIGHT CENTER
FRAME
CLIP
VEHICLE 21-PIN
CONNECTOR
(white)
CONNECTOR
CLIP (Discard.)
VEHICLE 21-PIN
CONNECTOR
VEHICLE
CONNECTOR
(gray)
RIGHT CENTER
FRAME
VEHICLE
CONNECTOR
(gray)
RIGHT CENTER
FRAME
30. Reconnect the vehicle connector (gray) and attach
the clip you just installed on the vehicle 21-pin
connector (white) to the right center frame.
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
AII 30556 (0509)
7 of 10
31. Route the day/night mirror harness 4-pin connector
with fuse case upwards to the vehicle harness,
and then along the vehicle harness to the fuse box
through the dashboard pocket opening.
33. Route the day/night mirror harness ground terminal
to the right along the vehicle harness at the rear of
the glove box frame.
GLOVE BOX
OPENING
DASHBOARD
DAY/NIGHT
MIRROR
POCKET OPENING
VEHICLE HARNESS
HARNESS
FUSE CASE
FUSE
BOX
INSTRUMENT
PANEL
BRACKET
DAY/NIGHT
MIRROR
HARNESS
DAY/NIGHT
MIRROR
HARNESS
4-PIN
CONNECTOR
DAY/NIGHT
MIRROR
DAY/NIGHT
MIRROR
HARNESS
HARNESS
GROUND
TERMINAL
SHIFT
LEVER
CABLE
VEHICLE
HARNESS
GROUND
BOLT
BOLT
32. Connect the day/night mirror harness 4-pin
connector to the accessory terminal of the fuse
box.
(Discard.)
34. Remove and discard the instrument panel bracket
bolt, and secure the day/night mirror harness
ground terminal to the instrument panel bracket
with the new ground bolt supplied.
DAY/NIGHT
MIRROR
HARNESS 4-PIN
CONNECTOR
DAY/NIGHT
MIRROR
HARNESS
FUSE BOX
ACCESSORY
TERMINAL
LOCATION
8 of 10
AII 30556 (0509)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
35. Tape a piece of steel wire to the 4-pin connector
end of the day/night mirror harness. Route the
harness end up along the instrument panel side
bracket, and out through the clearance between
the right front pillar and the instrument panel as
shown.
39. Secure the three clips from the day/night mirror
harness into the holes in the right front pillar.
DAY/NIGHT
MIRROR
HARNESS
CLIP
DAY/NIGHT MIRROR HARNESS
4-PIN CONNECTOR
RIGHT FRONT
PILLAR
RIGHT FRONT
PILLAR
PIECE OF
STEEL
WIRE
DAY/NIGHT
MIRROR
HARNESS
INSTRUMENT
PANEL
DAY/NIGHT
MIRROR
HARNESS
4-PIN
CONNECTOR
40. Using isopropyl alcohol, clean the areas where
the cushion tapes will attach. Using scissors, cut
two EPT sealers in half. Secure the day/night
mirror harness to the roof panel with three EPT
sealers.
ELECTRICAL
TAPE
4-PIN
CONNECTOR
36. Remove the electrical tape and the steel wire
from the day/night mirror harness.
EPT SEALER (Half)
remaining from step 40
37. Continue routing the day/night mirror harness 4-pin
connector up along the right front pillar, and out
through the roof console opening behind the head
liner.
ROOF CONSOLE
OPENING
MIRROR
HARNESS
HEAD
LINER
DAY/NIGHT
MIRROR
HARNESS
EPT SEALER
(Half: 3)
4-PIN
CONNECTOR
EPT SEALER
RIGHT
FRONT
PILLAR
DAY/NIGHT
MIRROR
HARNESS
41. Using the remaining half of EPT sealer, secure
day/night mirror harness 4-pin connector to the
roof panel.
38. Connect the day/night mirror harness 4-pin
connector to the mirror harness 4-pin connector.
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
AII 30556 (0509)
9 of 10
42. Secure the day/night mirror harness to the vehicle
harness with four wire ties.
44. Under the dashboard, secure the day/night mirror
harness to the vehicle harness with three wire
ties.
WIRE TIE
VEHICLE
HARNESS
DAY/NIGHT
MIRROR
HARNESS
DAY/
NIGHT
MIRROR
HARNESS
VEHICLE
HARNESS
WIRE TIE
43. Secure the day/night mirror harness to the vehicle
harness with three wire ties.
WIRE TIE
DAY/NIGHT MIRROR
HARNESS
45. Check that all wire harnesses are routed properly
and all connectors are plugged in.
46. Reinstall the driver’s side seat, torque the driver’s
seat bolts to 32 to 38 N·m (24 to 28 lb·ft)
VEHICLE
HARNESS
47. Reinstall all removed parts. Check that all clips
and other fasteners are installed securely.
48. Reconnect the negative cable to the battery.
49. Set the clock, and reset the radio station presets.
WIRE TIE
50. Check the operation of the automatic day/night
mirror according to the Owner’s Manual supplied.
NOTE: Whenever the battery is disconnected, the
driver’s AUTO function is disabled.
51. Start the engine. Push down on the driver’s
window switch until the window is fully open.
52. Pull up on the driver’s window switch fully to close
the window completely, then hold the switch for 2
seconds.
53. Test the driver’s window AUTO function.
10 of 10
AII 30556 (0509)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved.
|