Accessory
Application
Publications No.
AII 38137-38714
INSTALLATION
INSTRUCTIONS
Accessory HandsFreeLink
2008 ODYSSEY
Issue Date
JAN 2008
PARTS LIST
Fuse label
HFL Attachment Kit
P/N 08E02-SHJ-100B
HFL trim
Fuse (2 A)
6 EPT sealers
8 Wire ties
HFL bracket
HFL harness
HFL subharness
4 Self-tapping screw, 3 x 10 mm
2 Washer screws, 4 x 12 mm
2 Double-faced tapes
HFL retainer
Self-tapping screw
Bush
Ground bolt
Template
Rubber bumper
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
08E02-SHJ-1B00-91 1 of 12
3. Disengage eight retaining tabs and remove left
7. Using a flat-tip screwdriver, push the hook and
turn the holder. Remove the holder.
and right lens from the roof console.
PLASTIC TRIM TOOL
VEHICLE
CONNECTORS
SUNVISOR
HOLDER
VEHICLE
ROOF
CONSOLE
SUNGLASS
HOLDER
(Open.)
CONNECTOR
COVER
RIGHT
LENS
LEFT
RETAINING
TAB
SUNVISOR
2 SCREWS
4 RETAINING
TABS
8. Disengage two screws and remove the left
sunvisor.
2 BOLTS
2 BOLTS
LEFT
LENS
9. Pull away the weatherstrip from the left front A-
pillar trim. Release the side curtain air bag clip by
using the plastic trim tool and remove the left front
A-pillar (two clips).
4 RETAINING
TABS
4. Open the sunglass holder.
5. Remove four bolts and lower the roof console.
PLASTIC TRIM
TOOL
6. Disconnect the two vehicle connectors and
remove the roof console.
WEATHERSTRIP
SIDE CURTAIN
AIR BAG CLIP
LEFT FRONT
A-PILLARTRIM
CLIP
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
3 of 12
10. Remove the left front door sill trim (three clips).
12. Attach the fuse label (2 A) to the fuse case of the
HFL subharness.
3 CLIPS
LEFT FRONT
DOOR SILL TRIM
FUSE LABEL (2 A)
HFL
SUBHARNESS
HFL
SUBHARNESS
FUSE CASE
13. Plug the HFL subharness 6-pin connector into the
6-pin opening in the fuse box.
11. Pull away the weatherstrip from the left kick panel.
Remove the left kick panel (three clips).
3 CLIPS
WEATHERSTRIP
HFL
SUBHARNESS
LEFT KICK
PANEL
6-PIN
CONNECTOR
FUSE
BOX
4 of 12
AII 38137-38714 (0801)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
NOTE: If another accessory is already plugged into the
16. Remove the vehicle bolt (discard) and install the
ground bolt with HFL subharness ground terminal
as shown.
6-pin connector, remove the dummy connector
from the 6-pin connector taped to the HFL
subharness. Plug the 6-pin connector from the
other accessory harness into the 6-pin
connector from the HFL subharness you just
unplugged and plug the HFL subharness into
the fuse box.
FUSE BOX
HFL
SUBHARNESS
6-PIN
CONNECTOR
GROUND
BOLT
FUSE
BOX
VEHICLE
BOLT
(Discard.)
FUEL
OPENER
HFL SUBHARNESS
GROUND TERMINAL
DUMMY
CONNECTOR
HOOD
OPENER
OTHER ACCESSORY
6-PIN CONNECTOR
17. Disconnect the vehicle harness 1-pin connector
and connect it to the HFL subharness 1-pin
connector.
HFL SUBHARNESS
1-PIN CONNECTOR
VEHICLE
HARNESS 1-PIN
CONNECTOR
14. Route the HFL subharness to the left front pillar
trim opening.
HFL
SUBHARNESS
HFL
SUBHARNESS
WIRE
TIE
GREEN
TAPE
EPT
SEALER
VEHICLE
CLIP
VEHICLE
HARNESS
VEHICLE
HARNESS
EPT
SEALER
Cut in half.
HFL SUBHARNESS
CONNECTION PART
HFL
SUBHARNESS
LEFT FRONT
PILLAR TRIM
OPENING
18. Connect the HFL subharness 1-pin connector to
the vehicle 1-pin connector.
15. Route the HFL subharness and secure the
harness to the vehicle harness with a wire tie
above the vehicle clip as shown.
19. Wrap the cut one half of the EPT sealer on the
HFL subharness connection part.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
5 of 12
20. Secure the HFL subharness to the vehicle
23. Cut the template into template A and template B.
harness with a wire tie.
VEHICLE
PANEL
EPT
SEALER
TEMPLATE A
TEMPLATE
WIRE TIE
HFL
SUBHARNESS
TEMPLATE B
24. Remove the damper (two tapping screws).
VEHICLE
HARNESS
SUNGLASSES
HOLDER
21. Using isopropyl alcohol on a shop towel, clean the
area where the EPT sealer will attach. Attach a
EPT sealer to secure the HFL subharness to the
vehicle panel.
ROOF
CONSOLE
22. Secure the HFL subharness to the vehicle
harness with three wire tie.
VEHICLE
BUSHES
PIN
TAPPING
SCREW
HFL
SUBHARNESS
3 WIRE
TIES
CAMSET
LOCK
2 RETAINING
TABS
DAMPER
2 TAPPING
SCREWS
VEHICLE
HARNESS
25. Remove the sunglasses holder (tapping screw and
vehicle bushes).
26. Remove the pin and remove the camset lock (two
retaining tabs).
6 of 12
AII 38137-38714 (0801)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
27. Remove the console light from the roof console
29. Attach masking tape to the roof console as
(four retaining tabs).
shown.
ROOF
CONSOLE
MASKING
TAPE
ROOF
CONSOLE
4 RETAINING
TABS
30. Attach template A with masking tape to the roof
console at the indicated position.
CONSOLE
LIGHT
ROOF
CONSOLE
CENTER OF THE
ROOF CONSOLE
PUSHPIN
28. Enlarge the hole on the roof console with 9 mm
drill bit.
FELT-TIP
PEN
ROOF
CONSOLE
MARK
MASKING
TAPE
2 MARKS
TEMPLATE A
31. Using a felt-tip pen, mark the center of the roof
console as shown.
DRILL BIT
(9 mm)
32. Use a pushpin to mark the roof console at two
locations according to template A.
33. Remove template A.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
7 of 12
34. Drill 4.5 mm holes at the two locations marked on
39. Drill a 3 mm hole at the four locations marked on
the roof console in step 32. After drilling, remove
any burrs.
the roof console in step 36.
19 mm
HOLE SAW
DRILL BIT
(4.5 mm)
DRILL BIT
(3 mm)
ROOF
CONSOLE
ROOF
CONSOLE
4 MARKS
DRILL BIT
(3 mm 6 mm
10 mm)
2 MARKS
DRILL
35. Attach template B with masking tape on the roof
console at the indicated position.
PUSHPIN
FELT-TIP
PEN
40. Enlarge the two 3 mm holes drilled in step 39 with
a 6 mm drill bit and with a 10 mm drill bit as
shown.
41. Enlarge the other two 3 mm holes drilled in step
39 with a 19 mm hole saw as shown.
4 MARKS
TEMPLATE B
MASKING
TAPE
PUSHPIN
ROOF
CONSOLE
CENTER OF THE
ROOF CONSOLE
36. Use a pushpin to mark the roof console at four
locations according to template B.
37. Use a felt-tip pen and mark the roof console along
the template B.
38. Remove template B.
8 of 12
AII 38137-38714 (0801)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
42. Using a utility knife, cut along the marking made
45. Connect the HFL harness 22-pin connector to the
control unit.
on the roof console in step 37. After cutting,
remove any burrs.
CENTER
CONTROL
UNIT
ROOF
CONSOLE
UTILITY
KNIFE
Mark made in
step 37.
CONTROL
UNIT
Cut out.
ROOF
CONSOLE
HFL
HARNESS
ROOF
CONSOLE
HFL HARNESS
22-PIN
CONNECTOR
Remove the
adhesive
backing.
ROOF
CONSOLE
Cut out.
46. Using isopropyl alcohol on a shop towel, clean the
areas where the double-faced tape will attach.
Remove the adhesive backing from the double-
faced tape attached to the control unit and attach
to the roof console at the indicated position.
43. Remove the masking tape attached in step 29.
44. Using isopropyl alcohol on a shop towel, clean the
areas where the double-faced tape will attach.
Remove the adhesive backing from double-faced
tape and attach the double-faced tape at the
indicated position on the control unit.
47. Use the holes drilled in step 34 and secure the
HFL bracket with two 4 x 12 mm washer screws to
the roof console.
2 DOUBLE-FACED
TAPES
Holes drilled
in step 34.
CONTROL
UNIT
10 mm
10 mm
2 WASHER
ROOF
SCREWS,
CONSOLE
4 x 12 mm
CONTROL
UNIT
HFL
BRACKET
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
9 of 12
51. Connect the HFL harness 20-pin connector to the
48. Bend the switch terminal as shown.
switch.
BACKSIDE OF THE SWITCH
SWITCH
TERMINAL
(Bend.)
SELF- TAPPING
SCREW (Reuse.)
SPEAKER
SWITCH
SWITCH
TERMINAL
HFL TRIM
VEHICLE
BUSHES
(Reuse.)
SWITCH
BUSHES
HFL
RETAINER
HFL HARNESS
20 -PIN
CONNECTOR
SELF- TAPPING
SCREW
ROOF
CONSOLE
52. Install the switch assembled in step 50 to the roof
console with self-tapping screw, bushes, tapping
screw removed in step 25 and vehicle bushes.
53. Reinstall the console light to the roof console.
54. Using isopropyl alcohol on a shop towel, clean
the area where the EPT sealer will attach. Cut an
EPT sealer in half and attach one half to the
vehicle bracket as shown.
4 SELF-TAPPING
SCREWS,
3 x 10 mm
RUBBER
BUMPER
ROOF CONSOLE
OPENING
HFL
RETAINER
49. Insert the rubber bumper to the HFL retainer.
50. Assemble HFL retainer, switch, and HFL trim with
four 3 x 10 mm self-tapping screws.
VEHICLE
BRACKET
EPT SEALER
(Cut in half.)
EPT SEALER
10 of 12
AII 38137-38714 (0801)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
55. Hold the roof console close to the roof console
58. Connect the vehicle connectors to the roof
console. Reinstall the roof console with the four
bolts from step 5.
opening and connect the HFL harness 4-pin
connector to the HFL subharness 4-pin connector.
VEHICLE
CONNECTORS
WIRE TIE
GREEN
CONNECTOR
VEHICLE
BRACKET
HFL
SUBHARNESS
4-PIN
Vehicle front
CONNECTOR
ROOF
CONSOLE
ROOF
CONSOLE
OPENING
HFL HARNESS
4-PIN
CONNECTOR
2 BOLTS
2 BOLTS
ROOF
CONSOLE
59. Install the fuse (2 A) into the fuse box at the
indicated position.
56. Secure the connector with a wire tie to the vehicle
bracket.
57. Using isopropyl alcohol on a shop towel, clean the
area where the EPT sealer will attach. Secure the
HFL subharness to the vehicle roof panel inside
the roof lining with three EPT sealers.
3 EPT
SEALERS
HFL
SUBHARNESS
ROOF
PANEL
FUSE (2 A)
FUSE BOX
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 38137-38714 (0801)
11 of 12
60. Attach the fuse label to the No. 33 slot on the fuse
box cover.
61. Check that all wire harnesses are routed properly
and that all connectors are plugged in.
62. Reinstall all removed parts.
FUSE LABEL
(OPITION FUSE 2 A)
63. Reconnect the negative cable to the battery.
64. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
FUSE BOX
COVER
65. Reset the clock.
NOTE: When the battery is disconnected, the driver’s
window AUTO function is disabled.
•
Start the engine. Push down on the driver’s window
switch until the window is fully open.
•
Pull up on the driver’s window switch to close the
window completely, then hold the switch for
1 second or more.
•
Lower and raise the driver’s window to check
operation of the driver’s window AUTO function.
No. 33
12 of 12
AII 38137-38714 (0801)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
|