Heat Controller Inc Air Conditioner RAD 101A User Manual

+($7ꢀ&21752//(5ꢁꢀ,1&ꢂ  
AD-101A  
AD-81A  
ADS-81B  
CAU
• BEFOR
PRECA
• ONLY FOR AUTHORIZED SERVICE PERSONNEL.  
Safety Precautions  
Safety Precautions  
To prevent injury to the user or other people and property damage, the following instructions  
must be followed.  
Incorrect operation due to ignoring instructions will cause harm or damage. The seriousness  
is classified by the following indications.  
This symbol indicates the possibility of death or serious injury.  
WARNING  
This symbol indicates the possibility of injury or damage to property only.  
CAUTION  
Meanings of symbols used in this manual are as shown below.  
Be sure not to do.  
Be sure to follow the instruction.  
WARNING  
Always install the expansion panel(s).  
Do not place the power cord near a heater.  
• Improper assembly or installation may cause  
incorrect operation, including injury, fire, and  
electric shock hazards.  
• It may cause fire and electric shock.  
Do not use the power cord near flammable  
gas or combustibles such as gasoline,  
benzene, thinner, etc.  
Do not disassemble or modify products.  
• It may cause explosion or fire.  
• It may cause failure and electric shock.  
Service Manual 3  
Safety Precautions  
Plug in the power plug  
properly.  
Do not operate or stop the  
unit by inserting or pulling  
out the power plug.  
Do not damage or use an  
unspecified power cord.  
• Otherwise, it will cause  
electric shock or fire.  
• It will cause electric shock or  
fire.  
• It will cause electric shock or  
fire.  
Do not modify power cord  
length.  
Use the air conditioner on a  
single outlet circuit.(see page 7.)  
Do not share the outlet with  
other appliances.  
Always plug into a  
grounded outlet.  
• It will cause electric shock or  
fire.  
It will cause electric shock or  
fire.  
• No grounding may cause  
electric shock.  
Ventilate before operating air Do not use the socket if it is  
Do not operate with wet  
hands or in damp  
environment.  
conditionerwhen gas goes  
out.  
loose or damaged.  
It may cause explosion, fire,  
and burn.  
• It may cause fire and electric  
shock.  
• It will cause electric shock.  
4 Room Air Conditioner  
Safety Precautions  
If water enters the product, turn off the the  
power switch of the main body of appliance.  
Contact service center after taking the power-  
plug out from the socket.  
Do not clean the air conditioner with water.  
• It will cause electric shock or failure of  
machine.  
• Water may enter the unit and degrade the  
insulation. It may cause an electric shock.  
CAUTION  
Never touch the metal parts of the unit  
when removing the filter.  
Do not block the inlet or outlet.  
• They are sharp and may cause injury.  
It may cause failure of appliance or  
performance deteriorate.  
Ensure that the outer caseis not damaged  
by age orwear.  
Be cautious not to touch the sharp edges  
when installing.  
• Leaving it damaged couldresult in the air  
conditioner falling out of the window, creating  
a safety hazard.  
It may cause injury.  
Sharp  
edges  
Service Manual 5  
Dimensions  
Dimensions  
Symbols Used in this Manual  
This symbol alerts you to the risk of electric shock.  
This symbol alerts you to hazards that could cause harm to the  
air conditioner.  
NOTICE  
This symbol indicates special notes.  
Outside Dimensions  
11  
1
525(20 /16")  
470(18 /2")  
6 Room Air Conditioner  
Specfications  
rduct Specifications
MODELS  
RAD-101A  
ITEMS  
1Ø, 115, 60Hz  
POWER SUPPLY  
COOLING CAPACITY  
INPUT  
(Btu/h)  
(W)  
9,800  
1,000  
9.3  
RUNNING CURRENT  
(A)  
.
E.E.R  
(BTU/W h)  
9.8  
OPERATING  
26.7(DB)* 19.4(WB)**  
INDOOR ( C)  
OUTDOOR ( C)  
CONDITION  
35(DB)*  
23.9(WB)**  
410g(14.5oz)  
REFRIGERANT (R-22) CHARGE  
EVAPORATOR  
Ø 7.0, 3ROW 14STACKS  
Ø7.0 , 2R 16STACKS(L)  
CONDENSER  
TURBO FAN  
FAN, INDOOR  
PROPELLER TYPE FAN WITH SLINGER RING  
FAN, OUTDOOR  
3/3  
FAN SPEEDS, FAN/COOLING  
FAN MOTOR  
6 POLES  
REMOTE CONTROLLER  
THERMISTOR  
OPERATION CONTROL  
ROOM TEMP. CONTROL  
AIR DIRECTION CONTROL  
CONSTRUCTION  
HORIZONTAL LOUVER (UP & DOWN), VERTICAL LOUVER (RIGHT&LEFT)  
SLIDE IN-OUT CHASSIS  
OVERLOAD PROTECTOR  
COMPRESSOR  
PROTECTOR  
INTERNAL THERMAL PROTECTOR  
3 WIRE WITH GROUNDING  
FAN MOTOR  
POWER CORD  
DRAIN SYSTEM  
ATTACHMENT PLUG (CORD-CONNECTED TYPE)  
DRAIN PIPE OR SPLASHED BY FAN SLINGER  
18 1/2 x 13 7/8 x 20 11/16  
OUTSIDE DIMENSION  
(inch)  
(W x H x D)  
(mm)  
469 x 353 x 526  
* DB:Dry Bulb  
**WB:Wet Bulb  
Service Manual 7  
Specfications  
rduct Specifications
MODELS  
RAD - 81A  
ITEMS  
1Ø, 115, 60Hz  
POWER SUPPLY  
COOLING CAPACITY  
INPUT  
(Btu/h)  
(W)  
8,000  
815  
RUNNING CURRENT  
(A)  
7.6  
.
E.E.R  
(BTU/W h)  
9.8  
OPERATING  
26.7(DB)* 19.4(WB)**  
INDOOR ( C)  
OUTDOOR ( C)  
CONDITION  
35(DB)*  
260  
23.9(WB)**  
g(9.2 oz)  
REFRIGERANT (R-22) CHARGE  
EVAPORATOR  
Ø 7.0, 2ROW 14STACKS  
CONDENSER  
Ø5.0, 2ROW 16STACKS  
TURBO FAN  
FAN, INDOOR  
PROPELLER TYPE FAN WITH SLINGER RING  
FAN, OUTDOOR  
3/3  
FAN SPEEDS, FAN/COOLING  
FAN MOTOR  
6 POLES  
REMOTE CONTROLLER  
THERMISTOR  
OPERATION CONTROL  
ROOM TEMP. CONTROL  
AIR DIRECTION CONTROL  
CONSTRUCTION  
HORIZONTAL LOUVER (UP & DOWN), VERTICAL LOUVER (RIGHT&LEFT)  
SLIDE IN-OUT CHASSIS  
OVERLOAD PROTECTOR  
COMPRESSOR  
PROTECTOR  
INTERNAL THERMAL PROTECTOR  
3 WIRE WITH GROUNDING  
FAN MOTOR  
POWER CORD  
DRAIN SYSTEM  
ATTACHMENT PLUG (CORD-CONNECTED TYPE)  
DRAIN PIPE OR SPLASHED BY FAN SLINGER  
18 1/2 x 13 7/8 x 20 11/16  
OUTSIDE DIMENSION  
(inch)  
(W x H x D)  
(mm)  
469 x 353 x 526  
* DB:Dry Bulb  
**WB:Wet Bulb  
Service Manual 8  
Specfications  
rduct Specifications
MODELS  
RADS - 81B  
ITEMS  
1Ø, 115, 60Hz  
POWER SUPPLY  
COOLING CAPACITY  
INPUT  
(Btu/h)  
(W)  
8,000  
740  
RUNNING CURRENT  
(A)  
6.8  
.
E.E.R  
(BTU/W h)  
10.8  
OPERATING  
26.7(DB)* 19.4(WB)**  
INDOOR ( C)  
OUTDOOR ( C)  
CONDITION  
35(DB)*  
490  
23.9(WB)**  
g(17.3 oz)  
REFRIGERANT (R-22) CHARGE  
EVAPORATOR  
Ø 7.0, 2ROW 14STACKS  
CONDENSER  
Ø5.0, 2ROW 16STACKS  
TURBO FAN  
FAN, INDOOR  
PROPELLER TYPE FAN WITH SLINGER RING  
FAN, OUTDOOR  
3/3  
FAN SPEEDS, FAN/COOLING  
FAN MOTOR  
6 POLES  
REMOTE CONTROLLER  
THERMISTOR  
OPERATION CONTROL  
ROOM TEMP. CONTROL  
AIR DIRECTION CONTROL  
CONSTRUCTION  
HORIZONTAL LOUVER (UP & DOWN), VERTICAL LOUVER (RIGHT&LEFT)  
SLIDE IN-OUT CHASSIS  
OVERLOAD PROTECTOR  
COMPRESSOR  
PROTECTOR  
INTERNAL THERMAL PROTECTOR  
3 WIRE WITH GROUNDING  
FAN MOTOR  
POWER CORD  
DRAIN SYSTEM  
ATTACHMENT PLUG (CORD-CONNECTED TYPE)  
DRAIN PIPE OR SPLASHED BY FAN SLINGER  
18 1/2 x 13 7/8 x 20 11/16  
OUTSIDE DIMENSION  
(inch)  
(W x H x D)  
(mm)  
469 x 353 x 526  
* DB:Dry Bulb  
**WB:Wet Bulb  
Service Manual 9  
Installation  
Installation  
Select the Best Location  
1. To prevent vibration and noise, make sure the unit is installed  
securely and firmly.  
2. Install the unit where the sun does not shine directly on the  
unit.  
3. The outside of the cabinet must extend outward for at least  
11" and there should be no obstacles, such as a fence or  
wall, within 20" from the back of the cabinet because it will  
prevent heat radiation of the condenser.  
INSIDE  
OUTSIDE  
AWNING  
FENCE  
COOLED AIR  
HEAT  
RADIATION  
Restriction of outside air will greatly reduce the cooling effi-  
ciency of the air conditioner.  
ABOUT 1/4  
"
CAUTION: All side louvers of the cabinet must  
remain exposed on the outdside of the structure.  
Over 20"  
4. Install the unit slanted slightly so the back is slightly lower  
than the front (about 1/4"). This will force condensed water  
to the outside.  
Figure 1  
5. Install the unit with the bottom about 30"~60" above the  
floor level.  
Installation Check  
The setting conditions must be checked prior to initial starting.  
The following items are especially important checking points when the installation is finished.  
1. Grounding wire (Green or Green and Yellow) is provided in the power cord. The green wire must be grounded.  
2. Connect to a single-outlet 15A circuit.  
(or 20A circuit for Electric Heater Model)  
3. To avoid vibration or noise, make sure the air conditioner is installed securely.  
4 Avoid placing furniture or draperies in front of the air inlet and outlet.  
How to Secure the Drain Pipe  
In humid weather, excess water may cause the Base Pan to  
overflow. To drain the water, remove the Drain Cap and secure  
the Drain Pipe to the rear hole of the Base Pan. (Figure. 2)  
Drain Pipe  
Drain Cap  
Figure 2  
10 Room Air Conditioner  
Installation  
How to Install  
INNER  
SILL  
Window Requirements  
NOTICE  
All supporting parts should be secured to  
firm wood, masonry, or metal.  
1. This unit is designed for installation in standard double  
hung windows with actual opening widths of 22" to 36".  
The upper and lower sash must open sufficiently to allow  
a clear vertical opening of 15" from the bottom of the  
sash to the window stool.  
OUTER  
SILL  
2. If storm window presents interference, fasten a 2" wide  
wood strip to the inner window sill across the full width of  
the sill. The wood strip should be thick enough to raise  
the height of the window sill so that the unit can be  
installed without interference by the storm window  
frame. See Figure. 4. Top of wood strip should be  
approximately 3/4" higher than the storm window frame  
(STORM WINDOW FRAME) or wood strip (OUT-  
DOORS) to help condensation to drain properly to the  
outside.  
INDOORS  
OUTDOORS  
Figure 3  
1" MAX.  
WOOD STRIP MOUNTED  
ON TOP OF INNER SILL  
3/4"  
CLEARANCE  
STORM  
WINDOW  
FRAME  
INNER  
SILL  
WOOD STRIP  
3. Install a second wood strip (approximately 6" long by 11/2"  
wide and same thickness as first strip) in the center of the  
outer sill flush against the back off the inner sill. This will  
raise the L bracket as shown Figure. 4.  
FOR  
L
BRACKET  
OUTER  
SILL  
INDOORS  
OUTDOORS  
4. If the distance between STORM WINDOW FRAME and  
WOOD STRIP MOUNTED ON TOP OF INNER SILL is  
more than 1", two of wood strip are not necessary.  
Figure 4  
Installation  
HARDWARE  
Type A:16EA  
(SCREW)  
Type B:3EA  
(SCREW)  
Type C:5EA  
(SCREW)  
Type H:1EA  
(FOAM-STRIP)  
Type I:1EA  
(UPPER GUIDE)  
Type J:1EA  
(FOAM-PE)  
Type K:2EA  
(FRAME-GUIDE)  
Type L:1EA  
(WINDOW LOCKING BRACKET)  
Type M:1EA  
(FOAM-PE)  
Type N:1EA  
(DRAIN JOINT PIPE)  
Type O:1EA  
(DRAIN WASHER)  
Type D:2EA  
(NUT)  
Type E:2EA  
(FRAME CURTAIN)  
Type F:2EA  
(SILL SUPPORT)  
Type G:2EA  
(BOLT)  
10  
Service Manual 11  
Installation  
PREPARATION OF CHASSIS  
Shipping  
Screws  
1. Remove the screws which fasten the cabinet at both  
sides and at the back.  
2. Slide the unit from the cabinet by gripping the base  
pan handle and pulling forward while bracing the  
cabinet.  
3. Cut the window sash seal to the proper length.  
Peel off the backing and attach the Foam-Pe to the  
underside of the window sash.  
4. Remove the backing from the top Upper Guide Foam-  
Pe and attach it to the bottom of the Upper Guide.  
5. Attach the Upper Guide onto the top of the cabinet with  
3 type A screws.  
Upper Guide  
Foam-Pe  
6. Insert the Frame Guides into the bottom of the cabinet.  
Foam-Pe  
7. Insert the Frame Curtain into the Upper Guide  
and Frame Guides .  
Upper Guide  
(Type A)  
8. Fasten the curtains to the unit with 4 Type A screws.  
Screw  
Frame-Guide  
Screw  
(Type A)  
Screw  
Frame-Guide  
(Type A)  
CABINET INSTALLATION  
1. Open the window. Mark a line on center of the  
window stool(or desired air conditioner location).  
Carefully place the cabinet on the window stool and  
align the center mark on the bottom front with the  
center line marked in the window stool.  
Upper Guide  
Window stool  
Front Angle  
Figure 5  
2. Pull the bottom window sash down behind the Upper  
Guide until it meets.  
Window Sash  
Foam-pe  
Upper guide  
NOTICE  
Do not pull the window sash down so tightly  
that the movement of Frame Curtain is restricted.  
Cabinet  
Frame Curtain  
Foam-pe  
Figure 6  
12 Room Air Conditioner  
Installation  
3. Loosely assemble the Sill Support using the parts in  
Figure 7.  
INDOOR  
OUTDOOR  
Sill Support  
Nut  
Bolt  
Figure 7  
4. Select the position that will place the Sill Support  
near the outer most point on sill (See Figure 8)  
Frame Guide  
Screw(Type A)  
NOTICE  
Be careful when you install the cabinet (Frame  
Guides are broken so easily).  
Cabinet  
INDOOR  
OUTDOOR  
5. Attach the Sill Support to the cabinet track hole in  
relation to the selected position using 2 Type A  
screws in each support(See Figure 8).  
Figure 8  
Screw(Type B)  
Screw(Type A)  
6. The cabinet should be installed with a very slight  
tilt(about 1/2") downward toward the outside (See  
Figure 9).  
Adjust the bolt and the nut of Sill Support for  
balancing the cabinet.  
Sill support  
Sash track  
7. Attach the cabinet to the window stool by driving the  
screws (Type B: Length sixteen millimeters and  
below.) through the front angle into window stool.  
Front Angle  
Screw(Type B)  
8. Pull each Frame Curtain fully to each window sash  
Sill support  
Figure 9  
track, and repeat step 2.  
9. Attach each Frame Curtain the window sash using  
screws (Type C).(See Figure 10)  
Type C  
CAUTION: DO NOT DRILL A HOLE IN THE  
BOTTOM PAN.  
The unit is designed to operate with approximately  
1/2" of water in bottom pan.  
Figure 10  
Service Manual 13  
Installation  
10. Slide the unit into the cabinet.(See Figure 11)  
CAUTION: For security purpose, reinstall screws  
(Type A) at cabinet's sides.  
Power cord  
Screw(Type A)  
Screw(Type A)  
Figure 11  
11. Cut the Foam-Strip to the proper length and insert  
between the upper window sash and the lower  
window sash.  
(See Figure 12)  
Foam-Strip  
Figure 12  
12. Attach the Window Locking Bracket with a Type C  
screw. (See Figure 13)  
Window Locking Bracket  
13. Attach the front grille to the cabinet by inserting the  
tabs on the grille into the tabs on the front of the  
cabinet. Push the grille in until it snaps into place.  
(See Figure 14)  
Figure 13  
14. Lift the inlet grille and secure it with a Type A screw  
through the front grille.  
(See Figure 15)  
Figure 14  
Figure 15  
15. Window installation of room air conditioner is now  
completed. See ELECTRICAL DATA for attaching  
power cord to electrical outlet.  
Figure 16  
14 Room Air Conditioner  
Operation  
Operation  
DESIGNED FOR COOLING ONLY  
POWERFUL AND INCREDIBLE COOLING  
TOP-DOWN CHASSIS FOR THE SIMPLE INSTALLATION AND SERVICE  
BUILT-IN ADJUSTABLE THERMOSTAT  
WASHABLE ONE-TOUCH FILTER  
COMPACT SIZE  
Location and Function of Controls  
CAUTION: If you turn off the air conditioner or switch from cooling to the fan, wait  
at least 3 minutes before setting to cooling again.  
Operation  
O ff  
- Turns air conditioner off.  
Me d Fa n - Med speed fan operation without cooling.  
Low Fa n - Low speed fan operation without cooling.  
High C ool - Cooling with high speed fan operation.  
Me d C ool - Cooling with med speed fan operation.  
Low C ool - Cooling with low speed fan operation.  
Thermostat  
5
This automatically controls the temperature of the indoor air.  
Turn the knob so that arrow points to the larger marks for greater cooling.  
Point the arrow to the smaller marks for more moderate cooling.  
(i.e. the higher the number, the greater the cooling)  
6
4
3
7
8
2
1
9
FOR NORMAL COOLING  
1. Turn the operation switch to the High Cool or the Low Cool setting.  
2. Set the thermostat control to the desired temperature mark (the mid-point is a good starting  
position). If the room temperature is not satisfactory after a reasonable time, adjust the con-  
trol to a cooler or warmer setting, as appropriate.  
FOR MAXIMUM COOLING  
1. Turn the operation switch to the High Cool setting.  
2. Set the thermostat control to the largest temperature mark.  
FOR QUIETER OPERATION  
1. Turn the operation switch to the Low Cool setting.  
2. Set the thermostat control as needed.  
Service Manual 15  
Operation  
Remote Control Operations  
CAUTION: The Remote Controller will not function properly if strong light strikes  
the sensor window of the air conditioner or if there are obstacles between the  
Remote Controller and the air conditioner.  
The controls look like this:  
Controls  
Power  
1
7
Temp  
3
2
Fan Speed  
3
Timer  
Mode  
6
4
5
Energy  
Saver  
4
5
6
2
1
10 Hours ¡ 11 Hours ¡ 12 Hours ¡ CANCLE.  
The set temperature will be raised by 2°F after 30  
minutes and again after another 30 minutes.  
1. Power  
To turn the Set ON, push the button. To turn the  
Set OFF, push the button again.  
- Starting Operation  
This button takes priority over any other buttons.  
Each press of the button cycles through the options  
in this order:  
1 Hour ¡ 2 Hours ¡ 3 Hours ¡ 4 Hours ¡ 5 Hours  
¡ 6 Hours ¡ 7 Hours ¡ 8 Hours ¡ 9 Hours ¡  
10 Hours ¡ 11 Hours ¡ 12 Hours ¡ CANCLE.  
When you first turn it on, the Set is on the High cool  
mode and the temp. at 72°F  
2. Temperature Setting  
This button controls the room temperature setting  
in a range between 60°F and 86°F in 1° incre-  
ments.  
5. Energy Saver  
The fan stops when the compressor stops cooling.  
3. Fan Speed  
Approximately every 3 minutes the fan will turn on  
and check the room air to determine if cooling is  
needed.  
Pressing the Fan Speed button toggles between  
Low and High speeds.  
4. On/Off Timer  
6. Cool/Fan/Dry  
- Stopping Operation  
Everytime you push this button, it will toggle  
between COOL, FAN, and DRY.  
Each press of the button cycles through the options  
in this order:  
1 Hour ¡ 2 Hours ¡ 3 Hours ¡ 4 Hours ¡ 5 Hours  
¡ 6 Hours ¡ 7 Hours ¡ 8 Hours ¡ 9 Hours ¡  
How to Insert Batteries  
Do not use rechargeable batteries.  
Such batteries  
differ from standard dry cells in  
shape, dimensions, and perfor-  
mance.  
1. Remove the cover from the back of the remote con-  
troller  
2. Insert two batteries.  
Be sure of the polarity when installing the batteries.  
Be sure that both batteries are new.  
Remove the batteries from the  
remote controller if the air condi-  
tioner is not going to be used for  
an extended length of time.  
3. Re-attach the cover.  
16 Room Air Conditioner  
Disassembly  
Disassembly  
Before the following disassembly, POWER SWITCH set to OFF and disconnect the power cord.  
Mechanical Parts  
1. FRONT GRILLE  
1. Open the lnlet grille upward or downward.  
2. Remove the screw which fastens the front grille.  
3. Pull the front grille from the right side.  
4. Remove the front grille.  
5. Re-install the component by referring to the  
removal procedure, above.(See Figure 17)  
Figure 17  
2. CABINET  
1. After disassembling the FRONT GRILLE, remove  
the 2 screws which fasten the cabinet at both  
sides.  
2. Remove the 2 screws which fasten the cabinet at  
back.  
3. Pull the base pan forward. (See Figure 18)  
4. Remove the cabinet.  
5. Re-install the component by referring to the  
removal procedure, above.  
Figure 18  
3. CONTROL BOX  
1. Disconnect the unit from the power source.  
2. Remove the front grille.  
3. Remove the cabinet.  
4. Remove the screw which fastens the control box  
cover.  
5. Remove the housing which connects motor wire  
in the control box.  
6. Remove the 3 leads from the compressor.  
7.Discharge the capacitor by placing a 20,000  
ohmresistor across the capacitor terminals.  
8. Remove the 2 screws which fasten the control  
box.(See Figure 19)  
9. Pull the control box forward completely.  
10. Re-install the components by referring to the  
removal procedure, above. (See Figure 19)  
Figure 19  
Service Manual 17  
Disassembly  
Air Handling Parts  
1. AIR GUIDE AND BLOWER  
1. Remove the front grille.  
2. Remove the cabinet.  
3. Remove the control box.  
4. Remove the 3 screws which fasten the brace.  
5. Remove the brace.  
6. Remove the 2 screws which fasten the evaporator.  
7. Move the evaporator forward and pulling it upward  
slightly. (See Figure 20)  
8. Move the evaporator to the left carefully.  
9. Pull out the hook of orifice by pushing the tabs and  
remove it. (See Figure 21)  
Figure 20  
10. Remove the clamp with a hand plier which  
secures the blower.  
11. Remove the blower.  
12. Remove the 4 screws which fasten the air guide  
from the barrier.  
13. Move the air guide backward, pulling out from the  
base pan.  
14. Re-install the components by referring to the  
removal procedure, above.  
Figure 21  
2. FAN AND SHROUD  
1. Remove the cabinet.  
2. Remove the brace.  
3. Remove the 3 screws which fasten the condenser.  
4. Move the condenser to the left carefully.  
5. Remove the clamp which secures the fan.  
6. Remove the fan and then pull out the shroud.  
(See Figure 22)  
7. Re-install by referring to the removal procedure.  
Figure  
22  
18 Room Air Conditioner  
7—  
Disassembly  
3. MOTOR  
1. Remove the cabinet.  
2. Remove the evaporator.  
3. Remove the orifice.  
4. Remove the blower.  
5. Remove the fan.  
6. Remove the control box cover and housing of the  
motor in the control box.  
7. Remove the 2 screws which fasten the motor from  
the mount motor. (See Figure 23)  
8. Remove the motor.  
9. Re-install the components by referring to the  
removal procedure, above.(See Figure 23)  
Figure 23  
Electrical Parts  
1. OVERLOAD PROTECTOR  
1. Remove the cabinet.  
2. Remove the nut which fastens the terminal cover.  
3. Remove the terminal cover. (See Figure 24)  
4. Remove all the leads from the overload protector.  
5. Remove the overload protector.  
6. Re-install the component by referring to the  
removal procedure, above.  
Figure 24  
2. COMPRESSOR  
1. Remove the cabinet.  
2. Discharge the refrigerant system using a FreonTM  
Recovery System.  
If there is no valve to attach the recovery system,  
install one (such as a WATCO A-1) before venting  
the FreonTM. Leave the valve in place after  
servicing the system.  
3. Remove the overload protector.  
4. After purging the unit completely, unbraze the  
suction and discharge tubes at the compressor  
connections.  
5. Remove the 3 nuts and the 3 washers which  
fasten the compressor.  
6. Remove the compressor. (See Figure 25)  
7. Re-install the components by referring to the  
removal procedure, above.  
Figure 25  
Service Manual 19  
Disassembly  
3. CAPACITOR  
MODEL : ROTARY SWITCH TYPE MODEL  
1. Remove the control box.  
2. Remove the knobs and the screw which fasten  
control panel from control box.  
3. Remove the screw which is located in the front.  
4. Open the bottom side of control box.  
5. Remove the screw and the clamp which fasten the  
capacitor.  
6. Disconnect all the leads of capacitor terminals.  
7. Re-install the components by referring to the  
removal procedure, above. (See Figure 26)  
Figure 26  
MODEL : TOUCH & REMOTE CONTROL TYPE MODEL  
1. Remove the control box.  
2. Remove the screw which fasten control panel from  
control box.  
3. Remove the screw which located in the front.  
4. Open the bottom side of control box.  
5. Remove the screw and the clamp which fastens  
the capacitor.  
6. Disconnect all the leads of capacitor terminals.  
7. Re-install the components by referring to the  
Figure 27  
removal procedure, above. (See Figure 27)  
4. THERMOSTAT  
MODEL : ROTARY SWITCH TYPE MODEL  
1. Remove the control box.  
2. Open the control box.  
3. Remove the 2 screws which fasten the thermostat.  
4. Disconnect 2 leads of thermostat terminals.  
5. Remove the thermostat.  
6. Re-install the components by refereing to the above  
removal procedure. (See Figure 28)  
Figure 28  
20 Room Air Conditioner  
Disassembly  
6. ROTARY SWITCH  
MODEL : ROTARY SWITCH TYPE MODEL  
1. Remove the control box.  
2. Open the control box.  
3. Remove the 2 screws which fasten the rotary switch.  
4. Disconnect all the leads of the rotary switch terminals.  
5. Remove the rotary switch.  
6. Re-install the components by referring to the above  
removal procedure. (See Figure 29)  
Figure 29  
7. POWER CORD  
1. Remove the control box.  
2. Open the control box.  
3. Disconnect the grounding screw from the control  
box.  
4. Disconnect the 2 receptacles.  
5. Remove a screw which fastens the clip cord.  
(See Figure 30)  
6. Remove the power cord.  
7. Re-install the component by referring to the above  
removal procedure, above.  
(Use only one ground-marked hole  
connection.)  
for ground  
Figure 30  
8. If the supply cord of this appliance is damaged, it  
must be replaced by the special cord. (The  
special cord means the cord which has the same  
specification marked on the supply cord attached at  
the unit.)  
Refrigerating Cycle  
TM  
CAUTION: Discharge the refrigerant system using a Freon Recovery System. If there is no valve  
to attach the recovery system, install one (such as a WATCO A-1) before venting the Freon . Leave  
TM  
the valve in place after servicing the system.  
1. CONDENSER  
1. Remove the cabinet.  
2. Remove the 3 screws which fasten the  
brace.  
3. Remove the 3 screws which fasten the condenser  
and shroud.  
4. After discharging the refrigerant completely,  
unbraze the interconnecting tube at the condenser  
connections.  
5. Remove the condenser carefully.  
6. Re-install the component by referring to notes.  
(See Figure 31)  
Figure 31  
Service Manual 21  
Disassembly  
2. EVAPORATOR  
1. Remove the cabinet.  
2. Remove the 2 screws which fasten the evaporator.  
3. Move the evaporator sideways carefully.  
4. After discharging the refrigerant completely,  
unbraze the interconnecting tube at the evaporator  
connections.  
5. Remove the evaporator carefully.  
6. Re-install the component by referring to notes.  
(See Figure 32)  
3. CAPILLARY TUBE  
1. Remove the cabinet.  
2. After discharging the refrigerant completely,  
unbraze the interconnecting tube at the capillary  
tube.  
3. Remove the capillary tube.  
4. Re-install the component by referring to notes.  
Figure 32  
NOTICE  
remaining in the system. With valves A and B  
closed, stop the vacuum pump.  
4) Remove the hose from the vacuum pump and  
place it on the charging cylinder. See figure  
37B. Open valve C.  
Discharge the line at the manifold connection.  
5) The system is now ready for final charging.  
Replacement of the refrigeration cycle.  
1. When replacing the refrigeration cycle, be sure to  
TM  
Discharge the refrigerant system using a Freon  
recovery System.  
If there is no valve to attach the recovery system,  
install one (such as a WATCO A-1) before venting  
the Freon . Leave the valve in place after  
TM  
6. Recharge as follows :  
servicing the system.  
1) Refrigeration cycle systems are charged from  
the High-side. If the total charge cannot be put  
in the High-side, the balance will be put in the  
suction line through the access valve which you  
installed as the system was opened.  
2) Connect the charging cylinder as shown in figure  
33B.  
With valve C open, discharge the hose at the  
manifold connection.  
3) Open valve A and allow the proper charge to  
enter the system. Valve B is still closed.  
4) If more charge is required, the high-side will not  
take it. Close valve A.  
2. After discharging the unit completely, remove the  
desired component, and unbraze the pinch-off  
tubes.  
3. Solder service valves into the pinch-off tube ports,  
leaving the valves open.  
4. Solder the pinch-off tubes with Service valves.  
5. Evacuate as follows.  
1) Connect the vacuum pump, as illustrated figure  
33A.  
2) Start the vacuum pump, slowly open manifold  
valves A and B with two full turns counterclock-  
wise and leave the valves open.  
The vacuum pump is now pulling through valves  
A and B up to valve C by means of the manifold  
and entire system.  
5) With the unit running, open valve B and add the  
balance of the charge.  
a. Do not add the liquid refrigerant to the Low-side.  
b. Watch the Low-side gauge; allow pressure to  
rise to 30 lbs.  
c. Turn off valve B and allow pressure to drop.  
d. Repeat steps b. and c. until the balance of the  
charge is in the system.  
CAUTION: If high vacuum equip-  
ment is used, just crack valves A  
and B for a few minutes, then open  
slowly with the two full turns counter-  
clockwise. This will keep oil from foaming  
and being drawn into the vacuum pump.  
6) When satisfied the unit is operating correctly,  
use the pinch-off tool with the unit still running  
and clamp on to the pinch-off tube. Using a tube  
cutter, cut the pinch-off tube about 2 inches from  
the pinch-off tool. Use sil-fos braze and braze  
pinch-off tube closed. Turn off the unit, allow it to  
set for a while, and then test the leakage of the  
pinch-off connection.  
3) Operate the vacuum pump vaccum for 20 to 30  
minutes, until 600 microns of vaccum is  
obtained. Close valves A and B, and observe  
vacuum gauge for a few minutes. A rise in pres-  
sure would indicate a possible leak or moisture  
22 Room Air Conditioner  
Disassembly  
Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pin-off tool capable  
of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve.  
COMPOUND GAUGE  
CONDENSER  
(HIGH PRESSURE SIDE)  
MANIFOLD  
GAUGE  
A
B
CAPILLARY TUBE  
SEE INSETS  
BELOW  
EVAPORATOR  
(LOW PRESSURE SIDE)  
COMPRESSOR  
HI  
LOW  
A
A
B
B
EXTERNAL  
VACUUM PUMP  
CHARGING  
CYLINDER  
C
Figure 33B-Charging  
Figure 33A-Pulling Vacuum  
Service Manual 23  
Schematic Diagram  
Schematic Diagram  
Wiring Diagram  
MODEL : ROTARY SWITCH TYPE MODEL  
P OWE R INP UT  
1
BK(BR )  
WH(BL)  
(R ibbed)  
(P lain)  
R OTAR Y S WITC H  
G N(G N/YL)  
7
5
3
1
8
6
4
2
L
R D  
BK  
BL  
R D  
H
M
BK  
2
4
BL  
MOTOR  
OR (BR )  
YL  
G N(G N/YL)  
C AP AC ITOR  
YL  
F
6
OR (BR )  
C
BK  
BK  
R D  
BL  
R
H
R D  
S
C OMP .  
3
5
BK  
BR (YL) BL  
C
OLP  
THE R MOS TAT  
R D  
8
P .T.C  
WIR ING DIAG R AM  
3854AR 3563A  
7
S: Service Parts  
N: Non Service Parts  
LOCATION  
NO.  
Q'TY  
PER SET  
REMARKS  
DESCRIPTION  
1
2
3
4
5
6
7
POWER CORD ASSY  
S
S
S
S
S
S
S
1
1
1
1
1
1
1
FAN MOTOR  
COMPRESSOR  
ROTARY SWITCH  
THERMOSTAT  
CAPACITOR  
OVERLOAD PROTECTOR  
8
P.T.C  
S
1
24 Room Air Conditioner  
Schematic Diagram  
Circuit Diagram  
MODEL : TOUCH & REMOTE CONTROL TYPE MODEL  
1
6
2
7
4
5
3
8
LOCATION  
Q'TY  
DESCRIPTION  
NO.  
PER SET  
1
2
3
4
5
6
7
8
POWER CORD ASSEMBLY  
FAN MOTOR  
1
1
1
1
1
1
1
1
COMPRESSOR  
DISPLAY P.W.B ASSEMBLY  
MAIN P.W.B ASSEMBLY  
THERMISTOR  
CAPACITOR  
OWERLOAD PROTECTOR  
Service Manual 25  
Schematic Diagram  
Electronic Control Device  
26 Room Air Conditioner  
Schematic Diagram  
Components Location(For Main P.W.B ASM)  
Service Manual 27  
Troubleshooting Guide  
Troubleshooting Guide  
Piping System  
CONDENSER COIL  
FAN  
CAPILLARY TUBE  
COMPRESSOR  
MOTOR  
BLOWER  
EVAPORATOR COIL  
Figure 38 is a brief description of the important components and their function in what is called the refrigeration  
system. This will help you to understand the refrigeration cycle and the flow of the refrigerant in the cooling cycle.  
ROOM AIR CONITIONER  
CYCLE OF REFRIGERATION  
EVAPORATOR COILS  
CONDENSER COILS  
VAPOR INLET  
SUCTION LINE  
COOL LOW PRESSURE VAPOR  
HOT  
DISCHARGED  
AIR  
COMPLETE LIQUID  
BOIL OFF POINT  
COOLED  
AIR  
ROOM AIR HEAT LOAD  
OUTSIDE COOLING  
AIR FOR REFRIGERANT  
PASS THROUGH  
MOTOR  
COMPRESSOR  
OIL  
LIQUID  
PRESSURE  
DROP  
LIQUID OUTLET  
HIGH PRESSURE VAPOR  
(LIQUID REFRIGERANT)  
LIQUID REFRIGERANT  
LOW PRESSURE VAPOR  
CAPILLARY TUBE  
Figure 34  
28 Room Air Conditioner  
Troubleshooting Guide  
Troubleshooting Guide  
In general, possible trouble is classified in two kinds.  
The one is called Starting Failure which is caused from an electrical defect, and the other is ineffective Air  
Conditioning caused by a defect in the refrigeration circuit and improper application.  
Unit runs but poor cooling.  
Ineffective Cooling  
Check cold air  
circulation for smooth  
flow.  
Check outdoor coil  
(heat exchanger) and  
fan operation.  
Check heat load  
increase.  
Clean condenser.  
Dirty indoor coil  
(heat exchanger)  
Check gas leakage.  
Repair gas leak.  
Not on separate circuit  
Malfunction of fan.  
Check inside gas  
pressure.  
Replacement of unit if  
the unit is beyond repair.  
Clogging of air filter.  
Obstruction at air outlet.  
Remove obstruction.  
Adjust refrigerant  
charge.  
Malfunction of  
compressor.  
Check clogging in refrigera-  
tion circuit.  
Replacement of  
compressor.  
Satisfactory operation  
with temperature  
Repair clogging in  
refrigeration circuit.  
difference of inlet & outlet  
air; 44~50°F (7~10°C)  
Service Manual 29  
Troubleshooting Guide  
Fails to Start  
Check of circuit breaker  
and fuse.  
Check of power source.  
Check of control panel  
setting.  
Check control panel.  
Compressor fails only to  
start.  
Fan only fails to start.  
Improper wiring.  
Improper thermistor  
setting  
Drop of power voltage.  
Defect of fan motor  
capacitor.  
Defect of compressor  
capacitor.  
Loose terminal  
connection  
Irregular motor  
resistance ()  
Irregular motor  
insulation ()  
Capacitor check.  
Replacement.  
Improper wiring  
Replacement of fan motor.  
Regular but fails to start.  
Irregular motor resistance ()  
Irregular motor insulation ()  
Replacement of compressor.  
(Locking of piston, metal.)  
Replacement of compressor  
(Motor damaged).  
30 Room Air Conditioner  
Troubleshooting Guide  
¡ MODEL : BG8000ER, WG8000RY4, WG1000RY4  
ELECTRIC PARTS TROUBLESHOOTING GUIDE:  
The unit does not operate.  
Possible Trouble 1  
NO  
Check the Fuse.  
Check the wiring diagram.  
Is the Trans input power  
AC 115V?  
YES  
NO  
NO  
Check the Main  
P.W.B pattern.  
Is the Trans output power  
about AC 14V?  
Is shorted the Trans. output?  
YES  
YES  
Exchange the Trans.  
Exchange D02D~D05D.  
NO  
NO  
Is output Voltage of IC01D  
DC 12V?  
Exchange IC01D.  
YES  
Exchange IC02D.  
Is output Voltage of IC02D  
DC 5V?  
YES  
NO  
NO  
NO  
Is the reset circuit all right?  
(The No.14 of Micom  
is 5V.)  
Exchange IC01A.  
YES  
Is the  
Connect connector  
exactly.  
connection between  
Main and Display  
all right?  
YES  
Check the P.W.B  
pattern.  
Is the voltage No.18 of Micom  
DC 5V?  
YES  
Exchange Main P.W.B Ass'y.  
Service Manual 31  
Troubleshooting Guide  
The compressor does not operate.  
Set the Temp. setting to lower Temp.  
Possible Trouble 2  
Is Temp.  
setting set lower than Room  
Temp.-0.5°C?  
NO  
NO  
YES  
NO  
NO  
Is the voltage No.10  
of IC01M 0V?  
Is the voltage N0.7 of  
Is the Unit for 3 minutes  
delay?  
IC01M DC 5V?  
YES  
YES  
YES  
Check the RY-COMP.  
Check the wiring  
Diagram.  
Exchange IC01M.  
Wait 3 Minutes  
Exchange MAIN  
P.W.B Ass'y.  
The compressor always operate.  
Possible Trouble 3  
Connect LEAD Wire to  
RY-COMP again.  
NO  
Is the wire connection of  
RY-COMP all right?  
YES  
Check the RY-COMP.  
Fan does not operate.  
Possible Trouble 4  
NO  
Is the voltage NO.1 or 4  
of IC01M DC 5V?  
Exchange IC01M.  
Exchange IC01M.  
YES  
NO  
Is the voltage NO.13 or 16  
of IC01M 0V?  
YES  
Check the RY-Hi or  
RY-Lo.  
Check the wiring diagram.  
32 Room Air Conditioner  
Troubleshooting Guide  
Romote controller does not operate.  
Possible Trouble 5  
NO  
NO  
Is the voltage of Battery  
about over 2.3V?  
Exchange the battery.  
YES  
Is the voltage No.16  
of CN-DISP1 on Main P.W.B  
Ass'y DC 5V?  
Check the P.W.B pattern.  
YES  
Connect connector to  
CN-DISP1 exactly.  
NO  
Is the connection of  
CN-DISP1 all right?  
YES  
Exchange Receiver Ass'y.  
It displays abnormally on Display P.W.B Ass'y.  
Possible Trouble 6  
NO  
NO  
NO  
Exchange IC01G.  
Is the IC01G all right?  
YES  
NO  
Connect connector  
to CN-DISP1 exactly.  
Is the connection of  
CN-DISP1 all right?  
YES  
Does the Q01G,  
Q02G, Q03G Q04G operate normally  
on main P.W.B Ass'y?  
Exchange Q01G,  
Q02G, Q03G, Q04G  
YES  
Exchange the display  
P.W.B Ass'y.  
Service Manual 33  
Troubleshooting Guide  
ROOM AIR CONDITIONER VOLTAGE LIMITS  
NAME PLATE RATING  
115V ± 10%  
MINIMUM  
103.5V  
MAXIMUM  
126.5V  
COMPLAINT  
CAUSE  
REMEDY  
Fan motor will not run.  
No power  
Check voltage at outlet. Correct if none.  
Power supply cord  
Rotary switch  
Check voltage to rotary switch. If none, check  
power supply cord. Replace cord if circuit is  
open.  
Check switch continuity. Refer to wiring diagram  
for terminal identification. Replace switch if  
defective.  
Wire disconnected or  
connection loose  
Connect wire. Refer to wiring diagram for  
terminal identification. Repair or replace loose  
terminal.  
Capacitor (Discharge  
Test capacitor.  
capacitor before testing.)  
Replace if not within ±10% of manufacturer's  
rating. Replace if shorted, open, or damaged.  
Will not rotate  
Fan blade hitting shroud or blower wheel hitting  
scroll. Re-align assembly.  
Units using slinger ring condenser fans must  
have 0.22~0.25 inch clearance to the base.  
If necessary, shim up the bottom of the fan motor  
with mounting screw(s).  
Check fan motor bearings; if motor shaft will not  
rotate, replace the motor.  
Fan motor runs.  
Revolves on overload  
Check voltage. See limits on this page.  
If not within limits, call an electrician.  
Test capacitor.  
Check bearings. Does the fan blade rotate  
freely?  
If not, replace fan motor.  
Pay attention to any change from high speed to  
low speed. If the speed does not change,  
replace the motor.  
34 Room Air Conditioner  
Troubleshooting Guide  
REMEDY  
COMPLAINT  
CAUSE  
Fan motor noise.  
Fan  
If cracked, out of balance, or partially missing,  
replace it.  
Blower  
If cracked, out of balance, or partially missing,  
replace it.  
Loose set screw  
Worn bearings  
Tighten it.  
If knocking sounds continue when running or  
loose, replace the motor. If the motor hums or  
noise appears to be internal while running,  
replace motor.  
Compressor will not run,  
fan motor runs.  
Voltage  
Wiring  
Check voltage. See the limits on the preceding  
page. If not within limits, call an electrician.  
Check the wire connections; if loose, repair or  
replace the terminal. If the wires are discon-  
nected, refer to wiring diagram for identification,  
and replace the wires. Check the wire connections;  
If not according to the wiring diagram, correct  
the connections.  
Thermistor  
Check the TEMP control. If not at the lowest  
number, set TEMP control to this setting and  
restart the unit.  
Check the continuity of the thermistor. Replace  
the thermistor if the circuit is open.  
Rotary  
Check for continuity, refer to the wiring diagram  
for terminal identification. Replace the switch if  
the circuit is open.  
Thermostat  
Check the position of knob. If not at the coldest  
setting, advance the knob to this setting and  
restart the unit.  
Check the continuity of the thermostat. Replace  
the thermostat if the circuit is open.  
Capacitor (discharge  
capacitor before  
servicing.)  
Check the capacitor.  
Replace if not within ±10% of manufacturers  
rating, replace if shorted, open, or damaged.  
Compressor  
Check the compressor for open circuit or  
ground. If open or grounded, replace the  
compressor.  
Overload  
Check the compressor overload if externally mounted.  
Replace if open. (If the compressor temperature is  
high, remove the overload, cool, and retest.)  
Service Manual 35  
Troubleshooting Guide  
COMPLAINT  
CAUSE  
REMEDY  
Compressor cycles on  
overload.  
Voltage  
Check the voltage. See the limits on the  
preceding page. If voltage is not within these limits,  
call an electrician.  
Overload  
Check overload, if externally mounted.  
Replace if open. (If the compressor temperature  
is high, remove the overload, cool, and retest.)  
Compressor cycles on  
overload.  
Fan motor  
If not running, determine the cause. Replace if  
required.  
Condenser air flow  
restriction  
Remove the cabinet, inspect the interior surface  
of the condenser. If restricted, clean carefully  
with a vacuum cleaner (do not damage fins) or  
brush. Clean the interior base before  
re-assembling.  
Condenser fins  
(damaged)  
If the condenser fins are closed over a large  
area on the coil surface, head pressures will  
increase, causing the compressor to cycle.  
Straighten the fins or replace the coil.  
Capacitor  
Test the capacitor.  
Wiring  
Check the terminals. If loose, repair or replace.  
Check the system for a restriction.  
If restricted, clean or replace.  
Refrigeration system  
Air filter  
Insufficient cooling  
Excessive noise  
Unit undersized  
Blower or fan  
Determine if the unit is properly sized for the  
area to be cooled.  
Check the set screw, or clamp. If loose or miss-  
ing, correct. If the blower or fan is hitting scroll  
or barrier, rearrange the air handling parts.  
Copper tubing  
Remove the cabinet and carefully rearrange the  
tubing not to contact the cabinet,  
compressor, shroud, and barrier.  
36 Room Air Conditioner  
Exploded View  
554030  
554031  
749740  
731273  
559010  
267110  
W52106-2  
W52106-1  
249950  
238310  
249950  
263230  
266003  
W0CZZ  
552102  
552113  
352115  
W0CZZ  
269310  
137215  
268712  
352113  
146812  
264110  
135500  
135510  
135500  
149410  
35211A  
237200  
268714  
264110  
Replacement Parts List  
PART NO  
LOCATION NO  
DESCRIPTION  
Remark  
RAD-81A  
RAD-101A  
130410  
130910  
135312  
BASE ASSEMBLY,SINGLE  
CABINET ASSY,SINGLE  
3041A30011D  
3041A30005P  
R
R
R
3091A30005R  
GRILLE ASSY,FRONT(SINGLE)  
3531A29018B  
3530A10027A  
3550A30036B  
5210AR3196F  
4758A20002A  
4758A30008A  
135313  
135500  
749740  
147581  
147582  
149980  
152302  
237200  
238310  
249950  
264110  
263230  
267110  
268712  
268714  
GRILLE ASSY,INLET  
COVER,CONTROL(INDOOR)  
UPPER GUIDE CABINET  
LOUVER,HORIZONTAL  
LOUVER,VERTICAL  
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
SHROUD  
4998A10019A  
4998A10010A  
FILTER(MECH),A/C  
5231A20004A  
3720A20053A  
3831A20015R  
PANEL,CONTROL  
ESCUTCHEON  
CONTROL BOX ASSEMBLY,SINGLE  
POWER CORD ASSEMBLY  
THERMISTOR ASSEMBLY  
REMOTE CONTROLLER  
PWB(PCB) ASSEMBLY,DISPLAY  
PWB(PCB) ASSEMBLY,MAIN  
4995A20806C  
6411A20056A  
4995A20806D  
6411A20056E  
6323A20003S  
6711A20066C  
6871A20443B  
EBR39266506  
346811  
349001  
349480  
349600  
352113  
352115  
352390  
354210  
MOTOR ASSEMBLY,SINGLE  
DAMPER,VENTILAYION  
ORIFICE  
4681A20073Z  
4681A20027J  
R
R
R
R
R
R
R
R
4901A30001A  
4948A30007B  
4960A20014A  
MOUNT,MOTOR  
TUBE ASSEMBLY,DISCHARGE SINGLE  
TUBE ASSEMBLY,EVAPORATOR IN  
AIR GUIDE ASSEMBLY  
EVAPORATOR ASSEMBLY,FIRST  
5211A20708D  
5211AR2930Z  
5211A20130R  
5211A20130H  
5239A30002S  
5421A20061M  
5421A20061K  
359012  
550140  
FAN,TURBO  
ISOLATOR,COMP  
5900A10008A  
R
R
5040AR4195A  
4830AR4335A  
552102  
TUBE,CAPILLARY BEND  
5211A30260B  
5211A20598B  
R
552113  
554030  
554160  
559010  
567502  
731273  
TUBE ASSEMBLY,CONDENSER OUT  
CONDENSER ASSEMBLY,FIRST  
COMPRESSOR  
5211A10067G  
5403A20092H  
2520UCBA002 2520UCDK004  
5900A20015A  
6750UL048A  
3127A20074D  
5211A10067 P  
5403A20043 S  
R
R
R
R
R
R
FAN ASSEMBLY,AXIAL  
O.L.P  
INSTALL PARTS ASSEMBLY,SINGLE  
A
6750U-L031  
35211A  
TUBE ASSEMBLY,SUCTION SINGLE  
CAPACITOR  
AJR31679501  
0CZZA20005B  
R
R
5211A20130M  
0CZZA20001N  
W0CZ  
Z
vice Manual 37  
6SHFLILFDWLRQVꢀDQGꢀSHUIRUPDQFHꢀGDWDꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢁ  
+($7ꢀ&21752//(5ꢁꢀ,1&ꢂ  
ꢀꢁꢂꢂꢃ:(//:257+ꢃ$9(18(ꢃ‡ꢃ-$&.621ꢄꢃ0,&+,*$1ꢃꢅꢁꢆꢂꢇ  
7+(ꢃ48$/,7<ꢃ/($'(5ꢃ,1ꢃ&21',7,21,1*ꢃ$,5  
3ULQWHGꢃLQꢃ&KLQD  

Briggs Stratton 8FBC User Manual
Brother MFC 640CW User Manual
Bryant 704B User Manual
Dakota Digital UTV 6120 User Manual
Dell All in One Printer 942 User Manual
Fujitsu RO 36FA User Manual
GE General Electric Air Conditioner AS_14 User Manual
Haier AB124FAAHA User Manual
Haier Air Conditioner AC36ES1ERA User Manual
Heat Controller Inc Air Conditioner RAD 243A User Manual