Para obtener un ejemplar en Español de este
Pour demander un exemplaire en français de ce Manuel
Owner’s Manual
Installation and Operation
Models:
6000G
6000G-LP
6000G-IPI
6000G-IPILP
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- Do not try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
1
Table of Contents
1 Listing and Code Approvals
9 Gas Information
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 4
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 4
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4
G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
H. Requirements for the Commonwealth of Massachusetts. . 5
A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10 Electrical Information
A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 38
B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 38
C. Intellifire Ignition System Wiring. . . . . . . . . . . . . . . . . . . . 38
D. Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . . 39
E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 40
F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 40
2 Getting Started
A. Design and Installation Considerations . . . . . . . . . . . . . . . 6
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6
C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6
11 Finishing
A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C. Finishing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3 Framing and Clearances
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . . 8
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
12 Appliance Setup
A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 43
B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
D. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
G. Screen Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
H. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 10
5 Vent Information and Diagrams
A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
13 Operating Instructions
6 Vent Clearances and Framing
A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 47
B. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 48
C. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 50
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 22
B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 22
C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 23
D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 24
14 Troubleshooting
7 Appliance Preparation
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 51
B. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 53
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
B. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 26
C. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 26
D. Install the Optional HEAT-ZONE-GAS Kit . . . . . . . . . . . . 27
15 Maintaining and Servicing Appliance
A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
8 Installing Vent Pipe (DVP and SLP Pipe)
16 Reference Materials
A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 28
B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 29
C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 29
D. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 30
E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 30
F. Install Decorative Ceiling Components (SLP only). . . . . . 31
G. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 32
H. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 32
I. Install RF4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
J. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 34
K. Install Decorative Wall Components (SLP only). . . . . . . . 34
L. Heat Shield Requirements for Horizontal Termination . . . 34
M. Install Horizontal Termination Cap (DVP and SLP Pipe) . 35
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 57
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 58
C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
D. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 69
E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ꢀ= Contains updated information.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
3
Listing and Code Approvals
1
A. Appliance Certification
D. High Altitude Installations
U.L. Listed gas appliances are tested and approved with-
out requiring changes for elevations from 0 to 2000 feet in
the U.S.A. and Canada.
MODELS: 6000G, 6000G-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2000 • CSA2.33-M98 • UL307B
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating
by changing the existing burner orifice to a smaller size.
Input rate should be reduced by 4% for each 1000 feet
above a 2000 foot elevation in the U.S.A., or 10% for el-
evations between 2000 and 4500 feet in Canada. If the
heating value of the gas has been reduced, these rules
do not apply. To identify the proper orifice size, check with
the local gas utility.
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
WARNING
B. Glass Specifications
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous loca-
tions such as bathtub enclosures as defined by the Con-
sumerProductSafetyCommission(CPSC).Thetempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectur-
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750ºC, shall be considered
non-combustible materials.
F. Combustible Materials Specification
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can ig-
nite and burn, whether flame proofed or not, or whether
plastered or unplastered shall be considered combustible
materials.
Note: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and
the CAN/CGA B149 Installation Codes in Canada.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
Models
(U.S. or Canada)
• A110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
US
30,000
27,000
30,000
27,000
18,200
16,380
18,200
16,380
37
38
52
53
(0-2000 FT)
6000G (NG)
CANADA
(2000-4500 FT)
6000G-IPI (NG)
US
(0-2000 FT)
6000G-LP
CANADA
(2000-4500 FT)
6000GIPILP
4
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Inspection
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
The state or local gas inspector of the side wall horizon-
tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob-
serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfied:
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fu-
eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addi-
tion, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detec-
tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
In the event that the side wall horizontally vented gas fu-
eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur-
ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not pro-
vide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment in-
stallation instructions; and
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accor-
dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
• The “special venting systems” shall be Product Ap-
proved by the Board, and the instructions for that sys-
tem shall include a parts list and detailed installation
instructions.
Signage
A metal or plastic identification plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu-
eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
A copy of all installation instructions for all Product Ap-
proved side wall horizontally vented gas fueled equip-
ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
5
Getting Started
2
A. Design and Installation Considerations
C. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Carefully remove the appliance and components from
the packaging.
• Consult local building, fire officials or authorities having jurisdic-
tion about restrictions, installation inspection, and permits.
• The vent system components and trim doors are shipped
in separate packages.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• The gas logs may be packaged separately and must be
field installed.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the insta-
llation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Electrical wiring.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
WARNING
Keep appliance dry.
• Installation and use of any damaged appliance or vent
system component.
• Mold or rust may cause odors.
• Water may damage controls.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
B. Tools and Supplies Needed
• Improper positioning of the gas logs or the glass door.
Before beginning the installation be sure that the following
tools and building supplies are available.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Reciprocating saw
Pliers
Framing material
Hi temp caulking material
Gloves
Hammer
Phillips screwdriver
Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line
Level
Safety glasses
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Voltmeter
Manometer
Tape measure
Noncorrosive leak check solution
One 1/4 inch female connection (for optional fan).
6
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Framing and Clearances
3
Note:
WARNING
• Illustrations reflect typical installations and are FOR
Fire Risk
DESIGN PURPOSES ONLY.
Provide adequate clearance:
• Around air openings
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
• To combustibles
• For service access
A. Selecting Appliance Location
Locate appliance away from traffic areas.
When selecting a location for your appliance it is important to
consider the required clearances to walls (see figure 3.1).
Note: For actual appliance dimensions refer to Sec-
tion 16.
A
G
1/2 IN.
B
ALCOVE
INSTALLATION
E
A
B
C
TOP VENT
ONE 90º ELBOW
In addition to these framing dimensions, also reference the following sections:
•
•
Clearances and Mantel Projections (Sections 3.C and 3.D)
Vent Clearances and Framing (Section 6).
REAR VENT,
HORIZONTAL TERMINATION,
TWO ELBOWS
REAR VENT,
ONE ELBOW
REAR VENT,
NO ELBOWS
B
B
D
B
D
F
D
H
D
A
51
B
42
C
72
D
E
F
G
H
Inches
Millimeters
56-5/8
1438
22
17-3/4
451
8
See Section D.
Mantel Projections
1295
1067
1829
559
203
Figure 3.1 Appliance Locations
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
7
insulation. If the appliance is being installed on a cement
slab, a layer of plywood may be placed underneath to pre-
vent conducting cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that
run on the outside of a building may be, but are not re-
quired to be, installed inside a chase.
C. Clearances
Construction of the chase may vary with the type of build-
ing. These instructions are not substitutes for the require-
ments of local building codes. Local building codes MUST
be checked.
WARNING
Fire Risk.
Odor Risk.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
Chases should be constructed in the manner of all out-
side walls of the home to prevent cold air drafting prob-
lems. The chase should not break the outside building
envelope in any manner.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING
Fire Risk.
• Construct chase to all clearance specifications
in manual.
To further prevent drafts, the wall shield and ceiling
firestops should be caulked with high temperature caulk
to seal gaps. Gas line holes and other openings should
be caulked with high temp caulk or stuffed with unfaced
• Locate and install appliance to all clearance
specifications in manual.
A
E
J
F
B
H
C
D
G
I
Clearance to Combustibles
A
B
C
D
E
F
G
H
I
J
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Appliance
Sides of
Appliance
Front of
Appliance
Inches
10
38-1/2
978
22
42
26-5/8
676
0
0
0
0
1/2
13
1/2
13
36
Millimeters
254
559
1067
915
Figure 3.2 Clearances to Combustibles
8
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
D. Mantel Projections
TO CEILING
18
IN TER IO R W A LL
12
Top V iew
11
10
32
9
8
25
19
7
6
5
A
18
B
17
4
3
16
15
FIR E PL AC E
O P EN ING
14
13
12
M A N TE L LE G O R W A LL P RO JEC TIO N S
2-1/2
11
10
If A minimum is ____, then B maximum is_____.
5
Inches
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
A
Millimeters
Inches
62
1
87
2
113
3
138
4
164
5
189
∞
∞
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
B
Millimeters
25
51
76
102
127
Note: All measurements in inches.
Figure 3.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
Note: Measurement is taken from top of the
opening, NOT the top of the fireplace.
Figure 3.3 Clearances to mantels or other combustibles
above appliance
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
9
Termination Locations
4
HORIZONTAL
OVERHANG
A. Vent Termination Minimum Clearances
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
WARNING
LOWEST
DISCHARGE
OPENING
Fire Risk.
Explosion Risk.
GAS DIRECT VENT
TERMINATION CAP
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
X
12
• Combustible materials blocking cap may
ignite.
ROOF PITCH
IS X/ 12
• Restricted air flow affects burner operation.
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING
Roof Pitch
H (Min.) Ft.
Fire Risk.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
* 3 foot minimum in snow regions
Measure vertical clearances from this surface.
Figure 4.2 Minimum height from roof to lowest discharge
opening
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
GAS, WOOD OR FUEL
OIL TERMINATION
B
GAS
TERMINATION
C
A
Measure horizontal clearances from this surface.
(See Figure 4.4 for specific clearances)
Figure 4.1
Gas
Termination
Wood & Fuel Oil
Termination
Comments
A
B
C
6 in.
20 in.
18 in.
20 in. min.
24 in. min.
18 in.
Horizontal distance between terminations
Distance to perpendicular wall
Vertical distance between terminations
Figure 4.3 Multiple Vertical Termination
10
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
M
N
P
R
Q
(See Note 2)
V
T
S
S
Electrical
Service
V
V
D*
V
= VENT TERMINAL
X
= AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
A
B
= 12 inches.................clearances above grade, veranda,
L** = 7 ft.......................... clearance above paved
(See Note 1)
(See Note 1)
porch, deck or balcony
sidewalk or a paved driveway
located on public property
= 12 inches.................clearances to window or door
that may be opened, or to perma-
M*** = 18 inches................ clearance under veranda, porch,
deck, balcony or overhang
nently closed window. (Glass)
42 inches ............... vinyl
D* = 18 inches.................vertical clearance to unventilated
soffit or to ventilated soffit located
S
T
=
6 inches.................clearance from sides of electri-
(See Note 5)
above the terminal
cal service
*30 inches................for vinyl clad soffits and below
= 12 inches................clearance above electrical
electrical service
(See Note 5)
service
F
=
9 inches..................clearance to outside corner
Alcove Applications
G
H
= 6 inches...................clearance to inside corner
N
= 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
= 3 ft. (Canada)..........not to be installed above a gas
meter/regulator assembly within 3
P
= 8 ft.
feet (90 cm) horizontally from the
center-line of the regulator
QMIN
3 feet
6 feet
9 feet
12 feet
RMAX
I
= 3 ft...........................clearance to gas service regulator
vent outlet
1 cap
2 caps
3 caps
4 caps
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
J
= 9 inches (U.S.A.)
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
K
= 3 ft. (U.S.A.)
6 ft. (Canada)...........clearance to a mechanical (pow-
ered) air supply inlet
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
Note 3: Local codes or regulations may require different
clearances.
Note 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
Note 5: Location of the vent termination must not interfere with
access to the electrical service.
Note 1: On private property where termination is less than 7 feet above a
sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
WARNING: In the U.S: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang and ground
clearances as stated in the instructions.
Note 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper performance
of the appliance when the venting system does not meet these
requirements.
Figure 4.4 Minimum Clearances for Termination
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
11
Vent Information and Diagrams
5
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
Description
Vertical
First section (closest to appliance) of vertical length
V1
Second section of vertical length
V2
H1
H2
First section (closest to appliance) of horizontal length
Second section of horizontal length
8-1/2 in.
WARNING
Horizontal
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Figure 5.1
Do NOT connect this gas appliance to a chimney
flue serving a separate solid-fuel or gas burning
appliance.
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
May impair safe operation of this appliance or
other appliances connected to the flue.
2. Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see
Figure 4.1).
B. Use of Elbows
3. Vertical terminations are measured to bottom of termi-
nation cap.
CAUTION
4. Horizontal pipe installed level with no rise.
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these specifications.
• Appliance performance will suffer if specifications are not
Effective Length
Pipe
followed.
Inches
4
Millimeters
102
DVP4
DVP6
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
Effective
Height/Length
24
610
36
914
Two 45º elbows may be used in place of one 90º elbow. On
45º runs, one foot of diagonal is equal to 8-1/2 (216 mm)
inches horizontal run and 8-1/2 (216 mm) inches vertical
run. A length of straight pipe is allowed between two 45º
elbows (see Figure 5.1).
48
1219
76 to 152
3 to 6
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
Figure 5.2 DVP Pipe Effective Length
12
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
D. Vent Diagrams
WARNING
Fire Risk. Explosion Risk.
Note: The 6000 series fireplaces can adapt to
Do NOT pack insulation or other combustibles
between ceiling firestops.
SLP series vent pipe, if desired.
When venting off the top of the unit, use a DVP-2SL adapter and
a minimum 48 inch vertical section of SLP series vent pipe.
• ALWAYS maintain specified clearances around
venting and firestop systems.
• Install wall shield and ceiling firestops as speci-
fied.
After the 48 inch vertical section, the venting table rules
must be followed. The first 48 inch vertical section is NOT
counted as part of the vertical components in the table. It is
still counted as part of the overall maximum run. All venting
table rules for the vent run must still be followed.
Failure to keep insulation or other material away
from vent pipe may cause fire.
WARNING
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal
Fire Risk.
SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal
• When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
1. Top Vent - Horizontal Termination
One Elbow
V1 Minimum
H1 Maximum
Elbow only
2 ft
610 mm
914 mm
1.8 m
1 ft.
305 mm
610 mm
914 mm
1.2 m
3 ft.
6 ft.
2 ft.
3 ft.
4 ft.
11 ft.
20 ft.
3.4 m
6.1 m
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 20 ft. (6.1 m) Maximum
Note: For corner installations: A 6 inch (152
mm) section of straight pipe may need to
be attached to the appliance before a 90o
elbow, to allow the vent pipe to clear the top
standoffs.
Figure 5.3
V1 Minimum
H1 + H2 Maximum
Two Elbows
Note: For corner installations: A 6 inch
Elbow only
1 ft.
2 ft.
305 mm
610 mm
610 mm
1.2 m
(152 mm) section of straight pipe may
need to be attached to the appliance
before a 90o elbow, to allow the vent
pipe to clear the top standoffs.
6 in.
152 mm
305 mm
610 mm
914 mm
1.2 m
1 ft.
2 ft.
3 ft.
4 ft.
5 ft.
2 ft.
4 ft.
9 ft.
2.7 m
18 ft.
20 ft.
5.5 m
1.5 m
6.1 m
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.1 m) Maximum
Figure 5.4
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
13
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
V1 Min.
H1 Max.
V2 Min.
0 mm
H2 Max.
305 mm
Elbow only
2 ft.
610 mm
914 mm
1.8 m
0 in.
6 in.
1 ft.
1 ft.
2 ft.
6 ft.
6 in.
152 mm
305 mm
3 ft
152 mm
305 mm
610 mm
1.8 m
1 ft.
2 ft.
3 ft.
6 ft.
610 mm
914 mm
11 ft.*
16 ft *
3.4 m*
4.9 m*
2 ft.
3 ft.
610 mm
914 mm
10 ft.*
14 ft.*
3.1 m*
4.3 m*
*H1 + H2 = 20 ft. (6.1 m) Maximum
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
Figure 5.5
14
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
2. Top Vent - Vertical Termination
Flue Restrictor Instructions
1. Remove Exhaust Shield using a 1/4 inch nut driver by
removing the four screws securing it in place (see Figure
5.7).
V1 = 40 ft. Max. (12.4 m)
V1 = 3 ft. Min. (914 mm)
Note: If installing a vertical vent/
termination off the top of the appli-
ance, the optional vertical termina-
tion baffle should be used.
EXHAUST
SHIELD
FLUE
RESTRICTO R
No Elbow
Figure 5.7
2. Break the Flue Restrictor into two pieces. Do this by
bending the part back and forth until it breaks (see
Figure 5.8).
BREAK
HERE
Figure 5.6
Figure 5.8 Flue Restrictor
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
15
4. Center the Flue Restrictor on vent and secure in place
3. Match the amount of vertical you have in the sys-
tem with the chart to find the appropriate position
to set the Flue Restrictor (see Figure 5.9 ).
by using two self-tapping screws (see Figure 5.10).
5. Reinstall the Exhaust Shield.
TOP VENT
NG
REAR VENT
Vertical
4 ft.
LP
NG
LP
No
No
No
1-1
2-2
3-3
3-4
3-4
4-4
4-4
5-4
1
2
3
4
5
Restrictor Restrictor Restrictor
No
8 ft.
1-2
3-2
3-3
3-3
3-4
3-4
4-4
1-1
2-2
3-3
3-3
3-4
3-4
4-4
Restrictor
1-2
15 ft.
20 ft.
25 ft.
30 ft.
35 ft.
SETTING S
2-3
2-3
3-3
3-3
3-4
1
2
3
4
5
Figure 5.10
40 ft.
Figure 5.9
Note: If the DVP-2SL adapter and SLP pipe is used, you
MUST subtract one number from the table above.
Example: Top vent 40 ft vertical with DVP pipe = 5-4
Top vent 40 ft vertical with SLP pipe = 4-3
V1
Elbow only
6 in. 152 mm 6 ft.
H1 Maximum
V2 V1 + V2 Min.
Two Elbows
2 ft. 610 mm
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1.8 m
3.4 m
4.9 m
6.1 m
2 ft.
3 ft.
4 ft.
610 mm 11 ft.
914 mm 16 ft.
1.2 m
20 ft
V1 + V2 + H1 = 50 ft (15.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)
Figure 5.11
16
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
2. Top Vent - Vertical Termination - (continued)
V1
H1+ H2
305 mm
V2
*
V1 + V2 Minimum H1+ H2 Maximum
Three Elbows
Elbow only
1 ft.
2 ft.
2 ft.
4 ft.
9 ft.
18 ft.
*
*
*
*
*
*
*
*
*
*
*
*
1 ft.
2 ft.
2 ft.
4 ft.
9 ft.
18 ft.
305 mm
610 mm
610 mm
1.2 m
6 in.
1 ft.
2 ft.
3 ft.
4 ft.
152 mm
305 mm
610 mm
914 mm
1.2 m
610 mm
610 mm
1.2 m
*
*
*
2.7 m
*
2.7 m
5.5 m
*
5.5 m
H1+ H2 = 20 ft (6.1 m) Maximum
V1+ V2 + H1+ H2= 40 ft (12.2 m) Maximum
INSTA LL ED
H O R IZO NTA L LY
Figure 5.12
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
17
3. Rear Vent - Horizontal Termination
No Elbow
H1 = 16 in. (406 mm) Maximum
Figure 5.13
One 45º Elbow
Do not use a 450 elbow in corner installations.
Use two 900 elbows instead.
Figure 5.14
18
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
3. Rear Vent - Horizontal Termination - (continued)
H1 Maximum
V1 Minimum
H2
305 mm
H1+ H2 Maximum
Two Elbows
Back to Back
90º Elbows
1 ft.
305 mm
1 ft.
2 ft.
610 mm
2 ft.
3 ft.
3 ft.
3 ft.
3 ft.
610 mm 6 in.
914 mm 1 ft.
914 mm 2 ft.
914 mm 3 ft.
152 mm
305 mm
610 mm
914 mm
1.2 m
2 ft.
2 ft.
4 ft.
9 ft.
18 ft.
610 mm
610 mm
1.2 m
4 ft.
5 ft.
1.2 m
1.5 m
2.1 m
3.7 m
6.1 m*
7 ft.
2.7 m
12 ft.
20 ft.*
914 mm
4 ft
5.5 m
V1+ H1+ H2= 40 ft (12.2 m) Maximum
H1= 3 ft (914 mm) Maximum
*H1+ H2= 20 ft (6.1 m) Maximum
Figure 5.15
H1 Maximum
V1 Minimum
H2+ H3
305 mm
H1+ H2+ H3 Max.
Three Elbows
Back to Back
90º Elbows
1 ft. 305 mm
1 ft.
2 ft.
610 mm
2 ft. 610 mm 6 in.
152 mm 1.5 ft. 457 mm 3.5 ft.
1.1 m
1.5 m
2.1 m
3.7 m
4.6 m
3 ft. 914 mm
3 ft. 914 mm
3 ft. 914 mm
3 ft. 914 mm
1 ft.
2 ft.
3 ft.
4 ft.
305 mm
610 mm
914 mm
1.2 m
2 ft.
4 ft.
610 mm
1.2 m
5 ft.
7 ft.
9 ft.
2.7 m
12 ft.
15 ft.
12 ft.
3.7 m
V1+ H1+ H2+ H3= 40 ft (12.2 m) Maximum
H1= 3 ft (914 mm) Maximum
H1+ H2+ H3= 20 ft (6.1 m) Maximum
INS TALLE
D
HORIZON TAL LY
Figure 5.16
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
19
4. Rear Vent - Vertical Termination
One Elbow
V1 Minimum
H1 Maximum
2 ft. 610 mm
3 ft. 914 mm
6 in.
152 mm
305 mm
610 mm
914 mm
1.2 m
1 ft.
2 ft.
3 ft.
4 ft.
5 ft.
5 ft.
7 ft.
8 ft
1.5 m
2.1 m
2.4 m
2.4 m
1.5 m
8 ft
V1+ H1 = 40 ft (12.2 m) Maximum
H1 = 8 ft (2.4 m) Maximum
Figure 5.17
H1+ H2 Maximum
Back to Back 90° Elbows
V1 Minimum
Two Elbows
3 ft.
914 mm
2 ft
4 ft
610 mm
1.2 m
6 ft.
9 ft.
1.8 m
2.7 m
3.7 m
4.6 m
6 ft.
8 ft.
1.8 m
2.4 m
12 ft.
15 ft.
V1+ H1= 40 ft (12.2 m) Maximum
H1+ H2= 8 ft (2.4 m) Maximum
IN STA LL ED
H O R IZ O N TAL LY
Figure 5.18
20
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
4. Rear Vent - Vertical Termination - (continued)
H1 Maximum
V1 Minimum
H2
H1+ H2 Maximum
Three Elbows
2 ft. 610 mm 6 in.
3 ft. 914 mm 1 ft.
152 mm 2 ft. 610 mm
4 ft.
7 ft.
1.2 m
2.1 m
3.4 m
4.6 m
5.5 m
305 mm
610 mm
914 mm
1.2 m
4 ft.
6 ft.
1.2 m
1.8 m
2.4 m
3.1 m
5 ft.
7 ft.
8 ft
1.5 m
2.1 m
2.4 m
2 ft.
3 ft.
4 ft.
11 ft.
15 ft.
18 ft.
8 ft.
V2
10 ft.
H1= 8 ft (2.4 m) Max.
V1+ V2+ H1+ H2= 40 ft (12.2 m) Max.
H1+ H2= 20 ft (6.1 m) Max.
H2
V1
H1
Figure 5.19
H1
H2
H3
V1 Minimum
8 ft. 2.4 m
9 ft. 2.7 m
H1+ H2+ H3 Maximum
Three Elbows
*
*
*
*
*
*
*
*
*
6 ft.
7 ft.
8 ft.
8 ft.
1.8 m
2.1 m
2.4 m
2.4 m
*
*
*
10 ft.
10 ft.
3.1 m
3.1 m
V1+ H1+ H2+ H3 = 40 ft. (12.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1+ H1+ H2+ H3 cannot exceed 40 ft. (12.2 m) Maximum
H1+ H2+ H3 = 8 ft. (2.4 m) Maximum
V
1
H
3
H
1
H
2
INSTALLED
HORIZONTALLY
Figure 5.20
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
21
Vent Clearances and Framing
6
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
Combustible Wall Penetration
WARNING
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
• See Section 10.M. for information for regarding the in-
stallation of a horizontal termination cap.
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncom-
bustible materials such as concrete, a hole with diameter
one in. greater than the pipe is acceptable.
(DVP-SLP Pipe Shown)
Heat
3 in. (76 mm)
top clearance *
Heat
Shield
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
3 in. (76 mm)
top clearance
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
10 in.
10 in.
12 in.
C
D
10 in.
B*
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
A*
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materi-
als at wall shield firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
A*
B*
27-7/8
C
D
Figure 6.1 Horizontal Venting Clearances To Combustible
Materials
Inches
42-3/4
41-3/4
26-7/8
* Shows center of vent framing hole for top or rear venting. The center of the
hole is one (1) inch (25.4 mm) above the center of the horizontal vent pipe.
Figure 6.2 Exterior Wall Hole
22
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
C. Vertical Penetration Framing
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/floor (see
Figure 6.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 6.3).
A
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 6.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insu-
lation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
PIPE
DVP
SLP
10 in. (254 mm)
9 in. (229 mm)
Figure 6.3
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
CEILING FIRESTOP
INSTALLED BELOW CEILING
INSTALLED ABOVE CEILING
Figure 6.4 Installing the Attic Shield
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
23
D. Install Attic Insulation Shield
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be se-
cured in place.
Flat Ceiling Installation
• Remove one shield from box.
LASER-ETCHED
CUT LINES
INSERT 3
SCREWS
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
BEND 3 TABS
OUTWARD TO
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
CLEARANCE
allow attachment to the ceiling firestop.
Figure 6.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• The attic insulation shield has been laser-etched with cut
lines and ceiling pitches to make field trimming easier.
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) using a laser-etched cut line, to fit your ceiling
pitch. Snip cut edge to recreate 1 in. bend tabs all the
way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
24
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Appliance Preparation
7
A. Top Vent
Figure 7.1 For top vent, remove the two screws holding the
elbow heat shield in place. Use this heat shield over the
first elbow if applicable. For rear vent skip this step.
Figure 7.4 Fold the center parts of the retaining band up
and use to remove the vent cap.
Figure 7.2 Cut the seal cap strap across the rectangles
next to the disk.
Figure 7.5 Discard the vent cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it cannot be reattached.
Proceed to Section 7. C.
CAUTION
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
Figure 7.3 Remove the white gasket material covering
the seal cap.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
25
C. Securing and Leveling the Appliance
WARNING
Fire Risk.
• Prevent contact with sagging, loose insulation.
• Do NOT install against combustible materials
such as exposed insulation, plastic and insulation
backer.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 7.9). Nailing tabs are pro-
vided to secure the appliance to the framing members.
• Venting - refer to Vent Clearances and Framing (Section
6) for hole location.
Figure 7.6 Remove the insulation from the outer vent
pipe. For rear venting there is no insulation in the outer
vent pipe.
• Place the appliance into position.
• Level the appliance from side to side and front to back.
• Shim the appliance as necessary. It is acceptable to use
wood shims.
• Bend out nailing tabs on each side.
• Keep nailing tabs flush with the framing.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
Note: Once appliance is setup for top or rear venting, it
CANNOT be changed at a later time.
Figure 7.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket in the manual bag to seal
between the first vent component and the outer fireplace
wrap. Use 2 self tapping screws to secure the gasket to
the outer wrap.
Secure the first section of venting to the fireplace by screw-
ing through the two straps left over from cutting the seal
cap strap in step 2.
Note: Once appliance is setup for top or rear venting, it
CANNOT be changed at a later time.
NAILING TABS
(BOTH SIDES)
B. Installing the Non-combustible Board
The factory supplied non-combustible board spans the
distance from the top of the fireplace to the center of
the framing header. This board must be used. See
figure 7.8.
Figure 7.11 Proper positioning, leveling and securing of an
appliance
HEADER
WARNING
Fire Risk.
• ALWAYS maintain specified
clearances around the appliance.
• Do NOT notch into the framing around the appliance spacers.
Failure to keep insulation, framing or other material away from
the appliance may cause fire.
Figure 7.8 Non-combustible Board
26
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
D. Install the Optional HEAT-ZONE-GAS Kit
Note: There must be NO INSULATION or other combustibles
inside the framed firestop opening.
HEAT-ZONE-GAS
ATTACHES HERE
Figure 7.10
1. Remove the knockout from the fireplace and discard it
(see Figure 7.10).
2. Center the duct collar around the exposed hole and
attach it to the fireplace with 3 screws. Note: Do this
BEFORE final positioning of fireplace.
3. Determine the location for the air register/fan housing
assembly.
Reference the Heat-Zone-Gas kit instructions for the
remaining installation steps.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
27
Installing Vent Pipe (DVP and SLP Pipe)
8
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two sto-
ries), or High-Rise Applications
All outer pipe joints must be sealed with high temperature
silicone, including the slip section that connects directly to
the horizontal termination cap.
Figure 8.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when remov-
ing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
B
Figure 8.3
Figure 8.2
Assemble Pipe Sections (DVP Pipe Only)
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
Per Figure 8.2:
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
INCORRECT
Figure 8.4 Seams
28
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue
of the pipe section and the outer flue of the slip section
over the outer flue of the pipe section. See Figure 8.6.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Slide together to the desired length.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 8.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
High temperature caulk may be used to hold the part in
place.
• Continue adding vent components, locking each
succeeding component into place.
Pilot hole
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Figure 8.6 Slip Section Pilot Holes
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
Commercial, Multi-family (Multi-level exceeding two sto-
ries), or High-Rise Applications
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 8.7.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone,
including the slip section that connects directly to the hori-
zontal termination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when remov-
ing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 8.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
• Only outer pipes are sealed, sealing the inner flue is not
Figure 8.5 Adding Venting Components
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
29
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft.
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported
rise.
• Rotate either section (see Figure 8.10) so the seams
on both pipe sections are aligned as shown in Figure
8.11.
• Vertical runs of SLP pipe must be supported every 8 ft.
(2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal sections must be supported every 5 feet (1.52
m).
• Vent supports or plumbers strap (spaced 120º apart) may
be used to support. See Figures 8.8 and 8.9.
• Wall shield firestops may be used to provide horizontal
support.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per in-
stallation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 8.10 Rotate Seams for Disassembly
Figure 8.8 Securing Vertical Pipe Sections
Figure 8.11 Align and Disassemble Vent Sections
Figure 8.9 Securing Horizontal Pipe Sections
30
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceil-
ing through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
high temperature silicone to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
Adecorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
• Remove shingles or other roof covering as necessary to
cut the rectangular hole for the support box. Cut the hole
1/8 in. (3 mm) larger than the support box outline.
Figure 8.12
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
8.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 8.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
Figure 8.13
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
31
G. Install Metal Roof Flashing
Note: Skip this section if using the RF4-8.
• See minimum vent heights for various pitched roofs
(Figure 8.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 8.15.
HORIZONTAL
OVERHANG
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
Figure 8.15
WALL
LOWEST
DISCHARGE
OPENING
H. Assemble and Install Storm Collar
GAS DIRECT VENT
TERMINATION CAP
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
X
12
• Connect both halves of the storm collar with two screws
(see Figure 8.16).
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
Roof Pitch
H (Min.) Ft.
• Slide the assembled storm collar down the pipe section
Flat to 6/12........................................1.0*
Over 6/12 to 7/12............................1.25*
Over 7/12 to 8/12..............................1.5*
Over 8/12 to 9/12..............................2.0*
Over 9/12 to 10/12............................. 2.5
Over 10/12 to 11/12......................... 3.25
Over 11/12 to 12/12........................... 4.0
Over 12/12 to 14/12........................... 5.0
Over 14/12 to 16/12........................... 6.0
Over 16/12 to 18/12........................... 7.0
Over 18/12 to 20/12........................... 7.5
Over 20/12 to 21/12........................... 8.0
until it rests on the roof flashing (see Figure 8.17).
• Caulk around the top of the storm collar (see Figure 8.23).
* 3 foot minimum in snow regions
Figure 8.14 Minimum Height From Roof To Lowest Discharge
Opening
Figure 8.16 Assemblling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing could
cause water entry.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 8.15.
Figure 8.17 Assembling the Storm Collar Around the Pipe
32
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
I. Install RF4-8
The RF4-8 may be used in place of the roof flashing and
storm collar (Sections 8.G. and 8.H.)
Pipe must be supported within 12 inches of the roofline
using plumbers strapping or an SLP-FS when using
the RF4-8 Flashing. Refer to Section 8.D. Secure Vent
Sections.
SECURE WITH 4
SCREWS NO LONGER
THAN 1 IN. (25 MM)
Figure 8.20 Apply Sealant
SLP-FS
Figure 8.18 Secure Pipe with SLP-FS
• Trim the rubber boot (using scissors or a utility knife),
cutting along the marked measurement lines. See Figure
8.19. Use the 150 mm line for SLP, 210 mm for DVP.
• Lubricate pipe or flue with water and slide the flashing
down. It may be necessary to trim the top shingles around
the base of the rubber boot to ensure a good fit.
APPLY SEALANT
TOP & PARTIAL SIDES
• Draw around flashing, remove.
• Apply silicone sealant to roof inside the lines (Figure 8.20).
• Lubricate pipe or flue with water and slide flashing down.
Seat firmly in sealant. Nail roof flashing to the roof.
Figure 8.21 Slide Flashing Down, Secure & Apply Sealant
• Apply silicone sealant on the top outside of the base plate
on the sides and on top edge. See Figure 8.21. Install
shingles, Apply sealant at the top edge of the rubber
boot. See Figure 8.22.
SILICONE SEALANT
(TOP OF BOOT)
• We recommend that you top coat with conventional
acrylic house paint to improve the appearance of your
galvanized base flashing.
SHINGLES TRIMMED
FLASHING OVER
SHINGLES OVER
SHINGLES
FLASHING
Figure 8.22 Installation Complete
Figure 8.19 Trim Rubber Boot
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
33
J. Install Vertical Termination Cap
L. Heat Shield Requirements for Horizontal
Termination
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thick-
ness.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 8.23).
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.25).
• Heat shields must overlap 1-1/2 in. (38 mm) mini-
mum.
TERMINATION CAP
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.25.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must to be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
• Useanextendedheatshieldifthefinishedwallthickness
is greater than 7-1/4 in. (184 mm).
STORM
COLLAR
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
SCREWS
CAULK
• Attach the extended heat shield to either of the existing
heatshieldsusingthescrewssuppliedwiththeextended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 8.23
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
K. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
8.24.
Figure 8.24 Wall Thimble
34
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
M. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
HEAT SHIELD OR
HEAT SHIELD
EXTENDED
1-1/2 IN. (38 MM) MIN.
HEAT SHIELD
OVERLAP
WALL SHIELD
FIRESTOP
Failure to maintain overlap may cause overheating and
fire.
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
INNER VENT
SHEATHING
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
CAUTION! Risk of Burns! Local codes may require in-
stallation of a cap shield to prevent anything or anyone
from touching the hot cap.
Figure 8.25 Venting through the wall
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Depth
Rear Vent
Depth
Top Vent
Depth
Rear Vent
Depth
2-3/4 in. to
4-5/8 in.
3-1/8 in. to
5 in.
5-1/8 in. to
9-1/8 in.
5-1/2 in. to
9-1/2 in.
6000
Series
DVP-HPC1 DVP-HPC1
DVP-HPC2 DVP-HPC2
Top Vent
Depth
Rear Vent
Depth
Top Vent
Depth
Rear Vent
Depth
2-3/4 in. to
4-7/8 in.
3-1/8 in. to
5-1/4 in.
4-7/8 in. to
9 in.
5-1/4 in. to
9-3/8 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
35
Gas Information
9
A. Fuel Conversions
C. Gas Connection
Before making gas connections ensure that appliance be-
ing installed is compatible with the available gas type.
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter).
Any natural or propane gas conversions necessary to
meet the appliance and locality needs must be made by
a qualified technician using Hearth & Home Technologies
specified and approved parts.
B. Gas Pressures
Note: A listed (and Commonwealth of Massachusetts ap-
proved) 1/2 inch (13 mm) T-handle manual shut-off valve and
flexible gas connector are connected to the 1/2 inch (13 mm)
control valve inlet.
Proper input pressures are required for optimum appli-
ance performance. Gas line sizing requirements need to
be made following NFPA51.
•
If substituting for these components, please consult
local codes for compliance.
WARNING
Refer to Reference Section 16 for location of gas line
Fire Risk.
access in appliance.
Explosion Hazard.
High pressure will damage valve.
Note: Gas line may be run from either side of the appliance
provided the hole in the outer wrap does NOT exceed 2-1/2
inches in diameter and does not penetrate the firebox.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
Gas Leak Risk
• Support control when attaching pipe to
prevent bending gas line.
WARNING
Verify inlet pressures.
• High pressure may cause overfire condition.
• Low pressure may cause explosion.
Note: The gap between supply piping and gas access hole
may be caulked with high temperature caulk or stuffed with
non-combustible, unfaced insulation to prevent cold air
infiltration.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line
pressure is greater than 1/2 psig.
Pressure requirements for appliance are shown in the
table below. Minimum pressures must be met when other
household gas appliances are operating.
Pressure
Natural Gas
Propane
5.0 inches
w.c.
11.0 inches
w.c.
Minimum inlet pressure
14.0 inches
w.c.
14.0 inches
w.c.
Maximum inlet gas pressure
Manifold pressure
3.5 inches
w.c.
10.0 inches
w.c.
36
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
HIGH ALTITUDE INSTALLATIONS
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
• Incoming gas line should be piped into the valve
compartment and connected to the 1/2 inch connection
on the manual shutoff valve.
When installing this appliance at an elevation above 2000 feet,
it may be necessary to decrease the input rating by changing
the existing burner orifice to a smaller size. Input rate should
be reduced by 4% for each 1000 feet above a 2000 foot
elevation in the U.S.A., or 10% for elevations between 2000
and 4500 feet in Canada. If the heating value of the gas has
been reduced, these rules do not apply. To identify the proper
orifice size, check with the local gas utility.
WARNING
Fire or Explosion Hazard
• Gas buildup during line purge may ignite.
• Purge should be performed by qualified technician.
• Ensure adequate ventilation.
If installing this appliance at an elevation above 4500 feet (in
Canada), check with local authorities.
• Ensure there are no ignition sources such as
sparks or open flames.
• A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time for
air to purge from lines. When purging is complete the
appliance will light and operate normally.
WARNING
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have loosened
during shipping and handling.
WARNING
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
37
Electrical Information
10
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
A. Recommendation for Wire
This appliance requires 110-120 VAC be wired to the
junction box either for use of optional accessories (stand-
ing pilot ignition) or for proper operation of the appliance
(Intellifire ignition). Refer to Figure 10.1 to determine if the
appliance uses an Intellifire ignition system or Standing
Pilot ignition system.
• If using thermostat use one compatible with a millivolt
gas valve system.
• Follow parameters for locating thermostat (see individual
thermostat instructions) to ensure proper operation of
appliance.
Open the control access panel to view wiring system and
gas valve. If this appliance has a red or black ignitor button
(as noted in Figure 10.1) this appliance has a Standing Pilot
ignition system. If there is no red or black ignitor button,
this appliance has an Intellifire ignition system.
• Use low resistance thermostat wire for wiring from igni-
tion system to the wall switch and thermostat.
• Keep wire lengths short as possible by removing any
excess wire length.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
C. Intellifire Ignition System Wiring
This appliance requires a 110 VAC supply to the appliance
junction box for operation. A wiring diagram is shown in
Figure 10.2.
This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
This appliance is supplied with a battery pack and a 3 volt
AC transformer, which requires the installation of the sup-
plied junction box. It is highly recommended that the junc-
tion box be installed at this time to avoid reconstruction.
Figure 10.1 Standing Pilot Ignition
The battery pack requires two D cell batteries (not includ-
ed). Batteries cannot be placed in the battery pack while
using the 3 volt transformer. Batteries shouldn’t be placed
into the holder until needed. The higher temperatures will
shorten their life.
Note: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition or the Canadian Electric Code, CSA C221.1.
CAUTION
• A110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Battery polarity must be correct or module damage will
occur.
Optional Accessories Requirements
Wiring for optional accessories should be done now to
avoid reconstruction.
B. Connecting to the Appliance
WARNING
Wire 110V to electrical junction box.
Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch.
• Incorrect wiring will damage millivolt valves.
• Incorrect wiring will override IPI safety lockout
and may cause explosion.
38
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
PLUG-IN
3V TRANSFORMER
IGNITION MODULE 3 VAC
ON/OFF
WALL SWITCH
INTERMITTENT
PILOT IGNITOR
IGNITION
MODULE
(3V)
LOW VOLTAGE
SEE NOTE 1
VALVE
ORG
WHT
GROUND
REMOTE
CONTROL HOT
NEUTRAL
GROUND TO
FIREPLACE
CHASSIS*
BLACK WIRE CAN BE
PLUGGED INTO ANY
OF #1 - #5 LOCATIONS
ON THE HOT SIDE
ORG
BLK
RED
THERMOSTAT
WIRE
ASSEMBLY
WHITE WIRE CAN BE
PLUGGED INTO ANY
OF#1 - #5 LOCATIONS
ON THE NEUTRAL SIDE
VALVE
TRANSFORMER
3 VAC
REMOTE
JUMPER WIRE
PLUG-IN
*Note: Appliance will not operate unless properly grounded.
Figure 10.2 Intellifire Pilot Ignition (IPI) Wiring Diagram
D. Standing Pilot Ignition System Wiring
CAUTION
• This standing pilot ignition system wiring does not
require a 110 VAC supply to operate.
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
• It is recommended that a 110 VAC junction box be
installed for use with a fan or remote control. (See Figure
10.4 for junction box wiring).
WARNING
Shock hazard.
• Replace damaged wire with type 105º C rated
wire.
• Wire must have high temperature insulation.
STAND IN G
PILO T
BR N
RE D
VALV E
T H ER M O STAT
W IR E ASS EM B LY
O N /O FF PIG GY BAC K
W H T
RE D
W IR E
Figure 10.3 Standing Pilot Ignition Wiring Diagram
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
39
E. Junction Box Installation
Romex
Connector
•
Remove the screw attaching the junction box/re-
ceptacle to the outer shell, rotate the junction box
inward to disengage it from the outer shell (see
Figure 10.4).
14/2WG
•
Pull the electrical wires from outside the appli-
ance through this opening into the valve compart-
ment.
•
•
Feed the necessary length of wire through the
connector.
Make all necessary wire connections to the junc-
tion box/receptacle and reassemble the junction
box/receptacle to the outer shell.
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
Note: Do NOT wire 110
VAC to wall switch.
Figure 10.4 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall
mounted switch for use with a fan (See
Figure 10.5):
SWITCH
•
The power supply for the appliance
must be brought into a switch box.
MINIMUM 14-3
WITH GROUND
AW G
Red
Black
White
Green
•
The power can then be supplied from
the switch box to the appliance using
a minimum of 14-3 with ground wire.
Black
White
Green
JUNCTION BOX
•
•
At the switch box connect the black
(hot) wire and red (switch leg) wire to
the wall switch as shown.
POWER
SUPP LY WIRE
S
SWITCH BOX
At the appliance connect the black
(hot), white (neutral) and green
(ground) wires to the junction box as
shown.
Red
•
Add a 1/4 inch insulated female con-
nector to the red (switch leg) wire,
route it through the knockout in the
face of the junction box, and connect
to the top fan switch connector (1/4
inch male) as shown.
Figure 10.5 Junction Box Wired to Wall Switch
40
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Finishing
11
A. Mantel Projections
NON-COMBUSTIBLE ZONE (Shaded areas)
41 in.
Figure 11.1 shows the minimum vertical and correspond-
ing maximum horizontal dimensions of appliance mantels
or other combustible projections above the top front edge
of the appliance.
TO CEILING
Note: All
18
measurements
in inches.
12
11
10
32
9
8
25
7
39-3/8 in.
19
6
18
5
17
4
16
3
15
14
13
12
2-1/2
11
10
5
Figure 11.3 Noncombustible Facing
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Note: Measurement is taken from top of the
opening, NOT the top of the fireplace.
WARNING
Figure 11.1 Clearances to mantels or other combustibles
above appliance
Risk of Fire
• Non-combustible clearances MUST be
maintained.
IN TER IO R W A LL
Top V iew
• Sheetrock, wood or other combustibles must
NOT be used as sheathing or facing in the
non-combustible zone.
A
• See Section 11 for proper clearances.
B
• See Section 1 for combustible/non-
combustible definitions.
FIR E PL AC E
O P EN ING
M A N TE L LE G O R W A LL P RO JEC TIO N S
If A minimum is ____, then B maximum is_____.
WARNING
Inches
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
A
Millimeters
62
1
87
2
113
3
138
4
164
5
189
∞
∞
Fire Risk.
Inches
Finish all edges and fronts to clearances and
specifications listed in manual.
B
Millimeters
25
51
76
102
127
Figure 11.2 Mantel leg or Wall projections
(Acceptable on both sides of opening.)
• Do NOT overlap combustible materials onto appliance
front. The appliance front may only be covered with
noncombustible materials. The bottom one inch of the
appliance front is exempt and may be covered with either
non-combustible or combustible materials.
B. Facing Material
• Install combustible materials only up to specified
clearances on top, front and side.
WARNING
Fire Risk.
Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
• Seal joints between the finished wall and appliance top
and sides using only a 300º F minimum sealant.
• Modifying or covering grilles could cause
temperature rise and fire hazard.
Finishing materials must not interfere with:
• Air flow through grilles or louvers.
• Operation of louvers or doors.
• Access for service.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
41
C. Finishing Material
It’s very important to know what kind of a door and what
kind of finishing material is going to be used on the
fireplace. The table below shows the door models and the
finishing material thickness allowed. For an inside fit there
is an available template to assist with sizing the finishing
material.
ELBOW
HEAT
SHIELD
FINISHING
MATERIAL
FINISHING
MATERIAL
DOOR
FINISH
37 in.
(Outside door width)
MATERIAL
MAXIMUM
THICKNESS
SEE
FIGURE
DOOR
FIT
37-1/4 in.
(Includes 1/8 in. opening each side of door)
Folio
Inside
Overlap
Inside
Any
1 inch
11.4
11.5
11.6
11.5
11.7
11.5
11.6
11.5
11.6
11.5
11.7
Arcadia
Halston
Chateau
Valencia
Galleria
Any
Overlap
Inside
1 inch
1 inch - 2 inch
1 inch
Overlap
Inside
33-3/4 in.
34 in.
Any
37 in.
Overlap
Inside
1 inch
(Outside door width)
Any
Overlap
Inside
1 inch
37-1/4 in.
(Includes 1/8 in. opening each side of door)
1 inch - 2 inch
Finishing materials over 1 inch thick.
Figure 11.6 Inside fit door
ELBOW
HEAT
SHIELD
1-2 IN. THICK
FINISHING
MATERIAL
1-2 IN. THICK
FINISHING
MATERIAL
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED
Stop finishing material flush with opening.
DOORS
Figure 11.4 Folio Door
37 1/4 IN.
Finishing material between 1 and 2 inches thick.
Figure 11.7 Operable hinge door
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
Figure 11.5 Overlap Fit Door
42
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Appliance Setup
12
A. Remove Shipping Materials
D. Ember Placement
Remove shipping materials from inside or underneath the
firebox.
WARNING
Explosion Risk.
B. Clean the Appliance
• Follow ember placement instructions in manual.
• Do NOT place embers directly over burner ports.
• Replace ember material annually.
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
C. Accessories
Improperly placed embers interferes with proper burner
operation.
Install approved accessories per instructions included
with accessories. See Service Parts List for appropriate
accessories. Refer to Section 16.
Placing the Ember Material
Ember material is shipped with this gas appliance. To place
the ember material:
WARNING
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces just in front of the port trail,
but not on or in between the ports (see Figure 12.1).
Failure to follow this procedure will likely cause lighting
and sooting problems.
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
• Using non-listed accessories voids warranty.
• Using non-listed accessories may result in a
safety hazard.
• Only Hearth & Home Technologies approved
accessories may be used safely.
EMBER MATERIAL
Figure 12.1 Placement of Embers
• Place Mystic Embers on areas of base refractory away
from port holes. Use this material to give the appliance
a realistic ash bed.
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
43
E. Positioning the Logs
Log Assembly: LOGS-6000G
If the gas logs have been factory installed they
should not need to be positioned. If the logs have
been packaged separately, refer to the following
instructions.
1
STEP 1.
CAUTION: Logs are fragile! Carefully remove the
logs, grate and supporting cardboard from the
inside of the fireplace See Figure 12.2.
3
4
2
5
STEP 2.
Place the metal grate on top of the burner.
Position the legs of the grate into the forward set
of indentations in the burner top. Make sure the
grate is all the way forward. See Figure 12.3.
Figure 12.2
HUMP
SMALLER
HUMP
STEP 3.
Log #1 (SRV2103-107):
ꢁ
Place the log on the burner so the cutout in the
log goes around the hump in the burner. The outer
legs of the log should self center on the sides of
the burner. The ramp shape in the bottom of the
log sits fully against the ramp shape molded into
the burner. Pull the log forward. The right side of
log will touch the smaller hump. There will be a
1/4 inch or so gap around the hump. See Figures
12.4 and 12.5.
INDENTATIONS
Figure 12.3
1
1
Figure 12.4 Front View
Figure 12.5 Top View
2103-910
44
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
2
2
Figure 12.6 Front View
Figure 12.7 Top View
STEP 4. Log #2 (SRV2103-108): Place log #2 on top of the left side of log #1. The bottom of this log has a slot in it
that goes over the tab molded into the top of log #1. The left end sits behind the simulated ember cluster on the burner top.
3
3
Figure 12.8 Front View
Figure 12.9 Top View
STEP 5. Log #3 (SRV2103-110): Place log #3 on top of the burner surface in front of the hump. The bottom of
the log has a square groove cut through it. The groove sits over the second grate tine from the left. Slide it back against the
hump.
4
4
Figure 12. 11 Top View
Figure 12. 10 Front View
STEP 6. Log #4 (SRV2103-109): Place log #4 on top of the right side of log #1. The bottom of this log has a
slot in it that goes over the tab molded into the top of log #1. The other end of the log rests on the grate, against the second
tine from the right.
5
5
Figure 12.13 Top View
Figure 12.12 Front View
STEP 7. Log #5 (SRV2103-111): Place log #5 in front of log #3 the notch in the bottom of this log rests over
the center tine on the grate. The log shouldn’t cover any ports.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
45
F. Glass Assembly
G. Screen Mesh
Screen mesh is supplied with the optional doors.
WARNING
H. Grilles and Trim
Handle glass doors with care.
Install optional marble and brass trim surround kits as
desired. Marble, brass, brick, tile, or other noncombustible
materials can be used to cover up the gap between the
sheet rock and the appliance.
• Inspect the gasket to ensure it is undamaged.
• Inspect the glass for cracks, chips or scratches.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass door removed,
cracked, broken or scratched.
Do not obstruct or modify the air inlet/outlet grilles.
• Replace glass door assembly as a complete appliance.
I. Air Shutter Setting
Removing Glass Assembly
This appliance has an adjustable air shutter (which controls
the primary air) factory set for the minimum vertical vent
run (see Figure 12.15). If your installation has more than
the minimum required vertical vent length, adjustment of
the air shutter may be necessary to obtain optimal flame
appearance. This should be adjusted by a qualified
installer at the time of installation.
Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 12.14).
Replacing Glass Assembly
Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
By pushing the air shutter handle in, you will be closing
the air shutter. To adjust loosen the wing nut. Care should
be taken when adjusting the air shutter so as not to cause
the appliance to soot. If sooting occurs the air shutter will
need to be opened by pulling the handle out. When finished
tighten wing nut.
LATCHES
(BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
AIR SHUTTER
WING NUT
Figure 12.14 Glass Assembly
Figure 12.15
Shutter Settings
NG
LP
Burner
1/8 in.
Full Open
46
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Operating Instructions
13
A. Before Lighting Appliance
WARNING
Before lighting this appliance determine if it has a Standing
Pilot or Intellifire ignition system by opening the control
access panel to view wiring system and gas valve. If this
appliance has a red or black ignitor button (see Figure
10.1) this appliance has a Standing Pilot ignition system.
If there is no red or black ignitor button, this appliance has
an Intellifire ignition system.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
CAUTION
If installing Intellifire ignition battery backup:
• Do not install batteries if the backup mode may not be
used for extended time.
• Batteries may leak.
• Install batteries only when needed for power outage.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Before operating this appliance have a qualified tech-
nician:
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Remove all shipping materials from inside and/or under-
neath the firebox.
• Review proper placement of logs, rockwool, lava rock,
and vermiculite.
• Check the wiring.
WARNING
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
• Ensure that the glass is sealed and in the proper posi-
tion.
• Ensure that the flow of combustion and ventilation air is
not obstructed (front grilles and vent caps).
WARNING
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Glass door must be in place when appliance
is operating.
Risk of:
• Combustion Fumes
• Fire
Do NOT operate appliance with glass door
removed.
• Open viewing glass for servicing only.
• Glass door MUST be in place and sealed before operating
appliance.
• Only use glass door certified for use with appliance.
• Glass replacement should be done by qualified technician.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
47
B. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
(IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. Turn off all electric power to the appliance.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burn-
er. DO NOT try to light the burner by
hand.
2. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
GAS
VALVE
C. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
4. Turn on all electric power to the appliance.
WARNING: CAUTION:
5. To light the burner, flip the ON/OFF switch to
the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
6. If the appliance will not operate, follow the in-
structions “To Turn Off Gas to Appliance” and
call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
TO TURN OFF
GAS TO APPLIANCE
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
1. Turn wall control or ON/OFF switch to “OFF”.
NOT FOR USE
WITH SOLID FUEL
2. Turn off all electric power to the appliance if
If not installed, operated, and main-
tained in accordance with the man-
ufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause can-
cer, birth defects, or other reproductive
harm.
service is to be performed.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
593-913F
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional informa-
tion, consult a qualified installer, ser-
vice agency or the gas supplier.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
48
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Standing Pilot Ignition
LIGHTING
INSTRUCTIONS
1. Open control access panel.
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
2. Turn off all electric power to
the appliance.
3. Push in gas control knob
slightly and turn clockwise
to “OFF”.
• If you cannot reach your gas sup-
plier, call the fire department.
A. This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these in-
structions exactly.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, DO NOT try to repair
it, call a qualified service technician.
Force or attempted repair may re-
sult in a fire or explosion.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. DO NOT force.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
4. Open the fixed glass assembly. You may need to
remove the decorative front.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety
Information located on the left side
of this label. If you don’t smell gas,
go to next step.
D. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
6. Find the pilot. The pilot is inside
combustion chamber next to the
main burner
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
7. Turn knob on gas control counterclockwise
to “PILOT”.
8. Push in control knob all the way and hold in. Immedi-
ately depress red or black piezo button. It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
control knob in for about one minute after the pilot is
lit. Release knob and it will pop back out. Pilot should
remain lit. If it goes out, repeat steps 3 through 6.
WARNING: CAUTION:
Hot while in operation. DO NOT touch.
DO NOT CONNECT 110 VAC TO
Keep children, clothing, furniture, gaso-
THE CONTROL VALVE.
line and other liquids having flammable
Improper installation, adjustment, al-
vapors away.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
teration, service or maintenance can
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your ser-
vice technician or gas supplier.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
9. Reinstall fixed glass assembly. Reinstall decorative
front.
NOT FOR USE
WITH SOLID FUEL
10. Turn gas control knob counterclockwise
to “ON”. Close access panel.
If not installed, operated, and main-
tained in accordance with the man-
ufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause can-
cer, birth defects, or other reproductive
harm.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
11. Turn on all electric power to the appliance.
12. To light burner, turn the wall control or on/off switch
to “ON”.
TO TURN OFF
GAS TO APPLIANCE
1. Turn off all electric power to the appliance if ser-
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional informa-
tion, consult a qualified installer, ser-
vice agency or the gas supplier.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
vice is to be performed.
2. Open control access panel.
3. Move switch to “OFF” position.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
4. Push in gas control knob slightly and turn clock-
wise
to OFF”. DO NOT force.
5. Close control access panel.
Final inspection by
464-903H
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
49
C. After Appliance is Lit
CAUTION
Initial Break-in Procedure
• Prevent accidental appliance operation when not
attended.
When you light the appliance, you may notice that it pro-
duces heat which does have an associated odor or smell.
If you feel this odor is excessive it may require the initial
three to four hour continuous burn on high followed by a
second burn up to 12 hours to fully drive off any odor from
paint and lubricants used in the manufacturing process.
Condensation of the glass is normal.
• Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
• Property damage possible from elevated temperatures.
CAUTION
Note: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run
the appliance for an additional 12 hours. This will help to
cure the products used in the paint and logs.
Smoke and odors released during initial operation.
•
•
•
Open windows for air circulation.
Leave room during initial operation.
Smoke may set off smoke detectors.
Smoke and odors may be irritating to sensitive
individuals.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate any
odors associated with the appliance’s initial burning.
WARNING
Fire Hazard.
WARNING
Keep combustible materials, gasoline and
other flammable vapors and liquids clear of
appliance.
Fire Risk.
High Temperatures.
• Do NOT store flammable materials in the
appliance’s vicinity.
Keep combustible household items away from
appliance.
• Do NOT use gasoline, lantern fuel, kerosene,
charcoal lighter fluid or similar liquids in this
appliance.
Do NOT obstruct combustion and ventilation air.
• Do NOT place combustible items on top of or
in front of appliance.
• Combustible materials may ignite.
• Keep furniture, draperies away from
appliance.
D. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Condensation on the glass
This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
Blue flames
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufactur-
ing. Odor may also be released from finishing materials and adhesives used around the
appliance.
Odor from appliance
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Metallic noise
Is it normal to see the pilot flame burn In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
continually?
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
50
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Troubleshooting
14
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
Possible Causes
Corrective Action
1. After repeated triggering a. Defective ignitor.
of the red or black piezo
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor.
ignitor button, the spark
ignitor will not light the pilot.
b. Defective pilot or misaligned
electrode (spark at electrode).
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the red piezo ignitor button again. If the pilot lights, an im-
proper gas/air mixture caused the bad lighting and a longer purge
period is recommended. If the pilot will not light, ensure the gap
at the electrode and pilot is one-eighth (1/8) inch to have a strong
spark. If the gap is OK, replace the pilot.
c. No gas or low gas pressure.
Check the remote shut-off valves from the fireplace. Usually, there
is a valve near the gas main. There can be more than one (1) valve
between the fireplace and the main.
d. No LP in tank.
Check the LP (propane) tank. You may be out of fuel.
2. The pilot will not stay lit
after carefully following the
lighting instructions.
a. Defective thermocouple.
Check that the pilot flame impinges on the thermocouple. Clean
and/or adjust the pilot for maximum flame impingement.
Ensure that the thermocouple connection at the gas valve is fully
inserted and tight (hand tighten plus 1/4 turn).
Disconnect the thermocouple from the valve, place one millivolt
meter lead wire on the tip of the thermcouple and the other meter
lead wire on the thermocouple copper lead. Start the pilot and hold
the valve knob in. If the millivolt reading is less than 15mV, replace
the thermocouple.
b. Defective valve.
If the thermocouple is producing more than 15 millivolts, replace
faulty valve.
3. The pilot is burning,
a. ON/OFF switch or wires
defective.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the switch. If the burner
comes on, replace the defective switch. If the switch is OK, place the
jumper wires across the switch wires at the gas valve. If the burner
comes on, the wires are faulty or connections are bad.
there is no burner flame,
the valve knob is in the ON
position, and the ON/OFF
switch is in the ON position.
b. Thermopile may not be gener- If the pilot flame is not close enough physically to the thermopile,
ating sufficient millivoltage.
adjust the pilot flame.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millivolt meter. Take the reading at
TH-TP&TP terminals of the gas valve. The meter should read 325
millivolts minimum, while holding the valve knob depressed in the
pilot position, with the pilot lit, and the ON/OFF switch in the OFF
position. Replace the faulty thermopile if the reading is below the
specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The read-
ing should be 325 millivolts minimum. Replace the thermopile if the
reading is below the minimum.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
51
Troubleshooting (continued)
Symptom
Possible Cause
Corrective Action
3. Continued
c. Defective valve.
Turn the valve knob to the ON position. Place the
ON/OFF switch in the ON position. Check the millivolt
meter a the thermopile terminals. The millivolt meter
should read greater than 125mV. If the reading is ac-
ceptable, and if the burner does not come on, replace
the gas valve.
d. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stop-
page.
e. Wall switch or wires are defective.
Follow the corrective action in Symptom and Pos-
sible Cause 1.a above. Check the switch and wiring.
Replace where defective.
4. Frequent pilot outage a. Pilot flame may be too high or too low, or blow-
Clean thermocouple and adjust the pilot flame for
problem.
ing out (high pressure), causing pilot safety to drop maximum flame impingement. Follow lighting instruc-
out.
tions carefully.
5. The pilot and main
burner extinguish while
in operation.
a. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
b. Inner vent pipe leaking exhaust gases back into Check venting system for damage. Replace/repair
the system.
improperly assembled pipe sections.
c. Glass too loose and air tight packet leaks in
corners after usage.
Replace glass panel assembly.
d. Bad thermopile or thermocouple.
e. Improper vent cap installation.
Replace if necessary.
Check for proper installation and freedom from debris
or blockage.
6. Glass soots.
a. Flame impingement.
Adjust the log set so that the flame does not exces-
sively impinge on it.
b. Improper air shutter setting.
c. Debris around air shutter.
Adjust the air shutter located on the control panel.
Inspect the opening at the base of the burner. NO MA-
TERIAL SHOULD BE PLACED IN THIS OPENING.
7. Flame burns blue
and lifts off burner.
a. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
52
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
B. Intellifire Ignition System
Symptom
Possible Cause
Corrective Action
1. The ignitor/module
makes noise, but no
spark.
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Reversed wires at the module may cause system to make sparking
noise, but spark may not be present at pilot hood.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Rod closest to pilot hood should be ignitor.
Verify connections underneath pilot assembly are tight; also verify
connections are not grounding out to metal chassis, pilot burner,
pilot enclosure, mesh screen if present, or any other metal object.
c. Ignitor gap is too large.
d. Faulty module.
Verify gap of igniter to pilot hood. The gap should be approximately
.17 inch or 1/8 inch.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
2. Pilot won’t light,
there is no noise or
spark.
a. Transformer installed correctly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness.
Verify there is a tight fit. Verify pilot assembly wiring to module.
Remove and verify continuity of each wire in wiring harness.
c. Improper wall switch wiring.
d. Module not grounded.
Verify that 110/VAC power is “ON” to junction box.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
3. Pilot lights but con-
tinues to spark, and
main burner will not ig-
nite. (If the pilot contin-
ues to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
a. A shorted or loose connection in
sensor rod.
Verify all connections to wiring diagram in manual. Verify connec-
tions underneath pilot assembly are tight. Verify connections are
not grounding out to metal chassis, pilot burner, pilot enclosure or
screen if present, or any other metal object.
b. Poor flame rectification or contami- Verify that flame is engulfing sensor rod. If the pilot assembly does
nated sensor rod.
not have a ground strap, consider installing one to increase flame
rectification. Verify correct pilot orifice is installed and inlet gas
specifications. Flame carries rectification current, not the gas. If
flame lifts from pilot hood, the circuit is broken. A wrong orifice or
too high an inlet pressure can cause pilot flame to lift. The sensor
rod may be contaminated. Clean sensor rod with emery cloth.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
53
Intellifire Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
3. (Continued) Pilot lights c. Module is not grounded.
but continues to spark,
and main burner will not
Verify that module is securely grounded to metal chassis
of appliance. Verify that wire harness is firmly connected to
module.
ignite. (If the pilot contin-
d. Damaged pilot assembly or dirty sensor Verify that ceramic insulator around the sensor rod is not
ues to spark after the pilot
flame has been lit, flame
rectification has not oc-
curred.)
rod.
cracked, damaged, or loose. Verify connection from sensor
rod to white sensor wire. Clean sensor rod with emery cloth
to remove any contaminants that may have accumulated
on sensor rod. Verify continuity with a multimeter with
ohms set at lowest range.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF posi-
tion. Remove ignitor wire “I” from module. Place ON/OFF
Rocker switch or wall switch in ON position. Hold ground
wire about 3/16 inch away from “I” terminal on module. If
there is no spark at “I” terminal module must be replaced.
If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator
around electrode.
4. Pilot sparks, but Pilot
will not light.
a. Correct gas supply.
Verify that incoming gas line ball valve is “open”. Verify that
inlet pressure reading is within acceptable limits, inlet pres-
sure must not exceed 14 in. W.C.
b. Ignitor gap is too large.
c. Module is not grounded.
Verify that spark gap from ignitor to pilot hood is .17 in. or
1/8 in.
Verify module is securely grounded to metal chassis of
appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries
if voltage is below 2.7.
54
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Maintaining and Servicing Appliance
15
A. Maintenance Tasks
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified
service technician should perform an appliance checkup at the beginning of each heating season.
CAUTION
WARNING
Handle glass assembly with care.
Risk of injury or property damage.
Before servicing:
Note: Clean glass after initial 3-4 hours operation.
Longer operation without cleaning glass may
cause a permanent white film on glass.
• Turn off gas.
• Turn off electricity to appliance.
• Disable remote control, if one is present.
• Ensure appliance is completely cooled.
After servicing:
When cleaning glass door:
• Avoid striking, scratching or slamming glass.
• Do NOT use abrasive cleaners.
• Use a hard water deposit glass cleaner on white film.
• Do NOT clean glass when hot.
• Replace any screen or barrier that was removed.
• Reseal and reinstall any venting removed for servicing.
• Turn off appliance after 3-4 hours of operation and
ALLOW TO COOL.
• Remove and clean glass assembly.
• Replace glass assembly and operate appliance for
additional 12 hours.
WARNING
Annual inspection by qualified technician recommended.
Refer to maintenance instructions.
Check:
• Condition of doors, surrounds and fronts.
• Condition of glass, glass assembly and glass seal.
• Obstructions of combustion and ventilation air.
• Condition of logs.
WARNING
• Condition of firebox.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Burner ignition and operation.
• Burner air shutter adjustment
• Gas connections and fittings.
• Obstructions of termination cap.
• Combustible materials blocking cap may ignite.
• Restricted air flow affects burner operation.
Clean:
• Glass
• Air passageways, grilles,
control compartment
• Burner, burner ports
Risk of:
• Fire
• Delayed ignition or explosion
• Exposure to combustion fumes
• Odors
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
55
Inspect
Maintenance Tasks
Doors, Surrounds
and Fronts
1. Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present.
2. Inspect for scratches, dents or other damage and repair as necessary.
3. Verify no obstructions to airflow through the louvers.
4. Verify maintenance of proper clearance to combustible household objects.
1. Inspect gasket seal and its condition.
Gasket Seal, Glass
Assembly and Glass
2. Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame. Replace as necessary.
4. Verify that latches engage properly, clip studs are not stripped, and glass attachment components are
intact and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw
tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Firebox
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.
3. Replace ember materials with new dime-size and shape pieces. Do not block ports or obstruct lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting or other flame problems.
6. Verify air shutter is clear of dust and debris.
7. Inspect orifice for soot, dirt or corrosion.
8. Verify manifold and inlet pressures. Adjust regulator as required.
9. Inspect pilot flame strength. Clean or replace orifice as necessary.
10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
11. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or
sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
6. Inspect draft shield to verify it is not bent, damaged or missing.
1. Verify operation of remote.
Remote controls
2. Replace batteries in remote transmitters and battery-powered receivers.
3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure
or leaking.
56
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
Reference Materials
16
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
K
L
I
J
TOP VIEW
M
ELECTRICAL
ACCESS
GAS LINE
ACCESS
H
R
P
D
C
G
N
Q
E
B
A
F
O
LEFT SIDE
FRONT VIEW
RIGHT SIDE
Appliance Dimensions Table
Location
Inches Millimeters
Location
Inches
41
Millimeters
1041
918
J
K
L
11-5/8
28-1/2
14-1/4
8 dia
2-1/8
6-7/8
38
295
724
362
203
54
A
B
C
D
E
F
G
H
I
36-1/8
33-1/2
34-5/8
2-3/8
5
851
M
N
O
P
Q
R
879
60
175
965
25
127
26-7/8
8 dia
21-1/2
683
1
203
39-3/8
1000
546
Figure 16.1 Appliance Dimensions
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
57
B. Vent Components Diagrams
Effective Length
Pipe
DVP4
Inches
Millimeters
10 -1/2 in.
(267 m m )
4
102
°
4 5
E ffec tive
H eight/Length
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
4 -7/8 in.
( 276 m m )
24
610
36
914
10 -7/8 in.
(276 m m )
48
1219
76 to 152
DV P Pipe (see chart)
3 to 6
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
°
DVP45 (45 Elbow )
11-3 /8 in.
(289 m m )
10 in.
(254 m m )
10 in.
(25 4 m m )
1 in.
(25 m m )
7-3 /8 in.
(187 m m )
24 in.
(610 m m )
1-1/4 in. (32 m m )
9 -1/4 in.
(235 m m )
1/2 in. T Y P
(13 m m )
13 -1/4 in.
(3 37 m m )
DV P-FS (Ceiling F irestop )
DV P-AS (Attic S hie ld)
DV P 9 0S T (9 0° E lbow )
12 in.
(30 5 m m )
1 in.
(25 m m )
8 in.
(2 03 m m )
1- 1/2 in.
(38 m m )
10 in.
(254 m m )
14 in.
(356 m m )
UP
5 in.
(127 m m )
12 in.
(305 m m )
6 in.
(152 m m )
DV P-H VS (Vent Supp ort)
DV P-W S (W all S hield F irestop )
Figure 16.2 DVP vent components
58
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Minimum
Effective Length
Maximum
Effective Length
Term Cap
Trap1
3-1/8 in.
79 mm
4-5/8 in.
117 mm
9-3/8 in.
238 mm
Max
Effective
Length
12 in.
(305 mm)
5-3/8 in.
137 mm
Trap2
DVP-TRAP
Horizontal Termination Cap
DVP-TRAP2
DVP-TRAP1
DVP-TRAPK2
DVP-TRAPK1
DVP-HPC2
DVP-HPC1
Figure 16.3 DVP vent components
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
59
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
RF12M
Roof Flashing Multi-pak
Roof Flashing Multi-pak
5 in.
(127 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-3/4 in.
(349 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
COOL-ADD
Cap Shield
DVP-TRAPFL
Flashing
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DVP-HSM-B
Extended Heat Shield
DRC-RADIUS
Cap Shield
Figure 16.4 DVP vent components
60
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
B. Vent Components Diagrams (continued)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
(High w ind)
Vertical Term ination Cap
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
PVK-80
(For use with IPI and DSI appliances only.)
12 in.
(305 mm)
DVP-TB1
Basement Vent Ca p
14 in.
(356 mm)
16-7/8 in.
(429 mm)
7-1/4 in.
(184 mm)
1 in.
(25 mm)
12 in.
(305 mm)
14 in.
(356 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
3/8 in. (10 mm)
1 in. (25 mm)
1-5/8 in.
(41 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
DVP-HPC
High Performance Cap
DVP-FBHT
Fire Brick Term ination C ap
Figure 16.5 DVP vent components
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
61
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
8-3/8 in.
213 mm
3°
87°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Figure 16.6 DVP vent components
62
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP45
45° Elbow
SLP90
90° Elbow
Effective Height/Length
Pipe
SLP4
inches
4
mm
102
Effective
Height/
Length
SLP6
6
152
SLP12
SLP24
SLP36
SLP48
SLP6A
SLP12A
12
305
24
610
36
914
48
1219
51 - 152
51 - 305
2 - 6
2 - 12
SLP-WS
Wall Shield Firestop
SLP-PIPE
SLP-HVS
Horizontal Pipe
Support
RF4-8
Roof Flashing
SLP-FS
Ceiling Firestop
Figure 16.7 SLP Series Vent Components
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
63
B. Vent Components Diagrams (continued)
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLK-SNKD
Snorkel
Termination Cap
PVK-80
POWER VENT
SLP-TRAP1
Horizontal
SLP-TRAP2
Horizontal
Termination Cap
Termination Cap
(For use on IntelliFire
appliances only)
26 in.
660 mm
DVP-2SL
Adapter
SL-2DVP
Adapter
DVP-HSM-B
Extended Heat Shield
SLP-DCF-BK
Ceiling Firestop
Black
SLP-WT-BK
Wall Thimble-Black
Figure 16.8 SLP Series Vent Components
64
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
6000G, 6000G-IPI
C. Service Parts
Beginning Manufacturing Date: May 2006
Ending Manufacturing Date: ______
Service Parts Diagram
8
6
7
10
9
11
Log Set Assembly
1
4
2
3
5
Part number list on following page.
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
65
C. Service Parts List
6000G, 6000G-IPI
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
Log Assembly
Log #1
LOGS-6000G
SRV2103-107
SRV2103-108
SRV2103-110
SRV2103-109
SRV2103-111
2103-005
Y
1
2
Log #2
3
Log #3
4
Log #4
5
Log #5
6
Grate Assembly
Burner Assembly
7
SRV2103-007
2101-312
Y
Y
Y
8
Non-Combustible Board
Glass Assembly
Surround
9
GLA-6000G
2101-260
10
11
Junction box
4021-013
Flue Restrictor
385-128
Gasket Assembly
2103-081
Includes Vent, Seal Cap, Burner Neck, Shutter
Bracket, Manifold and Valve Plate gaskets
Glass Latch Assembly
Mineral Wool
386-122A
050-721
Y
Vermiculite Embers
Touch Up Paint
Mystic-Embers
203-9
ꢀ
Standing Pilot
Conversion Kit, NG
Conversion Kit, LP
Pilot Orifice, NG
Pilot Orifice, LP
Regulator, NG
Regulator, LP
Thermocouple
Pilot Tube
NGK-6G
LPK-6G
Y
Y
Y
Y
Y
Y
Y
Y
Y
2103-116
2103-117
230-1570
230-1520
446-511
SRV485-301
2103-512
Thermopile
IPI Ignition
Conversion Kit, NG
Conversion Kit, LP
Pilot Orifice, NG
Pilot Orifice, LP
Regulator, NG
NGK-6G-IPI
LPK-6G-IPI
593-528
Y
Y
Y
Y
Y
Y
593-527
NGK-DXV
LPK-DXV
Regulator, LP
Additional service part numbers on following page.
66
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
6000G
Service Parts
Beginning Manufacturing Date: May 2006
Ending Manufacturing Date: ______
Service Parts Diagram
Standing Pilot Valve Assembly
1
2
3
4
5
11
6
7
8
9
10
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2103-010
2103-011
582-837
Pilot Assembly, NG
Pilot Assembly, LP
Orifice NG (#37C)
Orifice LP (#52C)
Flex Tube Assembly
Shutter Sleeve
Y
Y
Y
Y
Y
Y
Y
1
2
582-852
3
4
5
6
7
8
383-302A
2026-130
2026-017
2118-104
302-320A
291-513
Shutter Bracket Assembly
Valve Bracket
Flex Ball Valve Assembly
Piezo Ignitor
Y
Y
Y
Y
Y
Y
Valve, NG
230-0710
230-0720
040-557A
2045-024
9
Valve, LP
10
11
Remote Pigtail Wire
Wire Assembly
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
67
6000G-IPI
Service Parts
Beginning Manufacturing Date: May 2006
Ending Manufacturing Date: ______
Service Parts Diagram
1
IPI Valve Assembly
2
3
4
5
11
6
7
10
8
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
582-837
Orifice, NG (#37C)
Orifice, LP (#52C)
Pilot Assembly, NG
Pilot Assembly, LP
Flex Tube Assembly
Shutter Sleeve
Y
Y
Y
Y
Y
Y
Y
1
582-852
2090-012
2090-013
383-302A
2026-130
2026-017
2118-104
302-320A
750-500
2
3
4
5
6
7
Shutter Bracket Assembly
Valve Bracket
Flex Ball Valve Assembly
Valve, NG
Y
Y
Y
Y
Y
Y
Y
Y
Y
8
Valve, LP
750-501
9
Module Wire Assembly
Control Module
593-590A
593-592
10
11
Thermostat Wire Assembly
3V Transformer
2045-024
593-593A
2103-013
593-594A
Remote Wire Assembly
Battery Pack
68
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
ꢀ
D. Limited Lifetime Warranty
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet
and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada.
Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood
Pellet
Electric Venting
Wood
All Parts and Material Except as
covered by Conditions, Exclusion,
and Limitations listed
1 Year
X
X
X
X
X
Igniters, Electronic Components,
and Glass
X
X
X
X
2 years
3 years
X
X
X
Blowers
Molded Refractory Panels
X
X
Firepots
5 years
3 years
3 years
X
X
Castings & Baffles
Firebox, HHT Chimney,
Termination & Heat
Exchanger
7 years
X
X
10 years 1 year
X
Burners, Logs & Refractory
Limited
1 year
X
X
Firebox & Heat Exchanger
All Replacement Parts
Lifetime
90 Days
X
X
X
X
X
See Conditions, Exclusions, and limitations.
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
9-01-08
• This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner,
provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its
original place of installation.
• The maximum amount recoverable under this warranty is limited to the purchase price of the product.
• In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
• Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is
not covered under this warranty.
Page 1 of 2
4021-645A 09-01-08
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
69
D. Limited Lifetime Warranty (continued)
• This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass
gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion
on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this
warranty.
• Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this
noise are not covered by this warranty.
• HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance
of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identification
label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper
handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate
ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced
air furnaces or other such causes; (5) use of fuels other than those specified in the operating instructions; (6) installation
or use of components not supplied with the appliance or any other components not expressly authorized and approved
by HHT; and/or (7) modification of the appliance not expressly authorized and approved by HHT in writing.
• This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction
with the installation of this product.
• This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine,
or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any
damage to the appliance or other components due to water or weather damage which is the result of, but not limited to,
improper chimney or venting installation.
• HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during
the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective
component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
• Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
• EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all
warranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary
parts or components, contact the nearest authorized HHT dealer or supplier.
Page 2 of 2
4021-645A 09-01-08
70
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
E. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609,
5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568,
5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474,
6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942,
6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436;
(Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2008
Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08
71
|
Briggs Stratton 28W700 User Manual
Briggs Stratton 460000 User Manual
Bryant R 22 561G User Manual
Friedrich MR24UY3F User Manual
Friedrich US12 User Manual
Frigidaire 15 User Manual
Graco UltraClear 2755B1 User Manual
Havis Shields Pentax Printer Mount & #39;96 08 Ford Crown Victoria C 3610 CV User Manual
Heat Controller Inc Air Conditioner B MMC12FA 1 User Manual
Honda Power Equipment GCV135GCV160 User Manual