Parts
Assembly
IMPORTANT! Before assembly, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
Front Leg
Back Leg
IMPORTANT! Please remove all parts from the package and identify
them before assembly. Some parts may be packed in the pad.
1
• Slide the front and back legs on the swing frame outward until
they "click" into place.
• Repeat this procedure to open the other swing frame.
2 Swing Frames
Press Buttons on Front Legs
Seat Frame
Base Tube
2
2 Base Tubes
Seat Pad
• While pressing the buttons on the end of each front leg, insert the
front legs into the ends of one of the base tubes.
• Push the front legs down into the base tube until the buttons
"click" into place.
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#6 x 3 cm Screw – 2
Shown Actual Size
3
Assembly
PULL UP
PULL UP
Base Tube
3
Base Tube
5
• While standing on the base tube, pull the front legs up. The front
legs should remain secured to the base tube. If you can remove
the front legs, you have not assembled them correctly to the base
tube. Re-read and repeat assembly step 2.
• While standing on the base tube, pull the back legs up. The back
legs should remain secured to the base tube. If you can remove
the back legs, you have not assembled them correctly to the base
tube. Re-read and repeat assembly step 4.
Seat Frame
Press Buttons
on Back Legs
Base Tube
4
Seat Hubs
Frame Arm
• While pressing the buttons on the end of each back leg, insert the
back legs into the ends of the remaining base tube.
• Push the back legs down into the base tube until the buttons
"click" into place.
Socket
6
• Position the seat frame so that the tubes are upright, as shown.
Hint: Note the location of the socket inside each seat hub.
The ends of the frame arms will be inserted into these sockets.
• Fit the end of each frame arm into the socket in each seat hub.
4
Assembly
Seat Hub
Slots
Waist Belt
Seat Hub
7
• Insert a screw through the outside of each seat hub and into
each frame arm. Tighten the screws.
Fasteners
9
• From behind the assembly, insert the waist belts through the
slots in the pad.
• Press to fasten the waist belt assembly to the pad.
Pad Upper Pocket
Pad Lower Pocket
Seat Bottom Tube
Seat Back Tube
10
Waist Belts
8
• Fit the pad lower pocket onto the seat bottom tube, as shown.
• Fit the pad upper pocket over the seat back tube.
5
Battery Installation
Battery Safety Information
In exceptional circumstances batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of product in a fire. The batteries inside may
explode or leak.
Battery Compartment Door
1,5V x 4
LR14 (“C”)
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
• Locate the battery compartment door on the frame.
• Loosen the screws in the battery compartment door.
• Remove the battery compartment door.
• Insert four LR14 ("C") alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need to reset
the electronics. slide the power switch off and then back on.
Note: Low battery power may cause product movement to slow
and sound volume to become faint or turn off all together. If this
should happen, please remove and discard all four batteries
and replace with four, new LR14 ("C") alkaline batteries.
• Protect the environment by not disposing of this
product with household waste (2002/96/EC).
Check your local authority for recycling advice and
facilities (Europe only).
6
Securing Your Child
Restraint System
WARNING
To prevent serious injury from
falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product
on an elevated surface.
2
• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to the next section for instructions
to tighten the waist belt.
Waist Belt
Anchored End
Anchored End
Buckle
Free End
Free End
Restraint Pad
TIGHTEN
LOOSEN
3
1
To tighten the belts:
• Feed the anchored end of the belt up through the buckle to form
• Place your child in the seat. Position the restraint pad between
your child’s legs.
A
a loop . Pull the free end of the belt B . Repeat this procedure
to tighten the other belt.
To loosen the belts:
• Fasten both waist belts to the buckles on each side of the
restraint pad.
• Feed the free end of the belt up through the buckle to form
Make sure you hear a "click" on both sides.
A
a loop . Enlarge the loop by pulling on the end of the loop
• Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint should
remain attached.
IMPORTANT! The maximum weight limit for this product is
9 kg (20 lbs). If your child weighs less than 9 kg (20 lbs), but is
really active and appears to be able to climb out of the swing,
immediately discontinue its use.
toward the buckle. Pull the anchored end of the belt to shorten
the free end of the belt B . Repeat this procedure to loosen the
other belt.
Please Note: After adjusting the belts to fit your child, make sure
you pull on them to be sure they are securely fastened.
7
Starting the Swing
Storage
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Power Switch
• Lift the seat bottom.
• Slide the power switch to any of five speed settings.
• Give the seat a light push to start the swinging motion. Adjust
the power switch to the desired swing motion setting.
Hint: As with most battery-powered swings, a heavier child will
reduce the amount of swinging motion on all settings. In most
cases, the low setting works best for a smaller child while the high
setting works best for a larger child.
• If swinging stops while using a lower setting, try a higher setting.
Give the seat a light push to start the swinging motion again.
• Be sure to turn this product off when not in use. Slide the power
switch to the off setting O.
• Press the frame release buttons on the inside of the frames and
push the front legs inward.
8
|