Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the pad.
2 Toys
(Toys may be different)
Adjustable Pillow
Seat Back Tube
Pad
Footrest
Left Base Wire
Base Tube
2 Feet
Right Base Wire
#8 x 1,9 cm (3/4") Screw – 2
M5 x 20 mm Screw – 2
Shown Actual Size
NOTE: Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
3
Assembly
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if needed.
Never substitute parts.
Base Tube
Left Base Wire
Right Base Wire
1
3
•Place the base tube on a flat surface.
•Position the left and right base wires as shown.
•Fit the left base wire and right base wire into the base tube.
•Insert an M5 x 20 mm screw through each foot and tighten.
Footrest
Feet Holes
2
•Position the feet so the holes are toward you and the
non-skid surface is down.
Base Wires
•Fit the feet on the base tube, as shown.
4
•Position the footrest so that the soothing unit is upright.
•Fit the footrest onto the ends of the base wires.
4
Assembly
Seat Back Tube
Seat Back Pocket
Square Openings
Bottom Pocket
5
•Position the seat back tube so that the square openings
are upright.
•Fit the seat back tube onto the ends of the base wire.
•Push the seat back tube to be sure it is completely on the
base wires.
7
•Fit the pad seat back pocket over the seat back tube.
•Pull and fit the pad seat bottom pocket around the soothing
unit and footrest.
Handles
8
6
•Fit the handles through the side openings in the pad.
3
•Insert a #8 x 1,9 cm ( / ") screw into the inside hole of each
4
handle and tighten.
•Pull up on the seat back tube to be sure it is secured to the
left and right base wires.
5
Assembly
Battery Installation
Hint: We recommend using an alkaline battery for
longer battery life.
Toy Bar Plugs
1,5V
“D” (LR20)
–
+
Sockets
•Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
9
•Insert and “snap” the toy bar plugs into each handle socket.
Hint: The toy bar is removable. Press the ends of the latches
and lift the toy bar.
Toy Bar Straps
1
•Remove the pad bottom pocket from the footrest.
Battery Compartment
2
•Insert a coin into the battery compartment door and pry the
battery compartment door off.
•Insert one“D”(LR20) alkaline battery into the bat-
tery compartment.
•Replace the battery compartment door.
•Pull and fit the pad seat bottom pocket around the soothing
unit and footrest.
10
•Fasten the toy straps to the toy bar straps.
Assembly is now complete.
6
Battery Safety Information
Setup and Use
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
Restraint Pad
•Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use.
Always remove exhausted batteries from the product.
Dispose of batteries safely. Do not dispose of product in
a fire.The batteries inside may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type
as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the product
before charging.
•If removeable, rechargeable batteries are used, they are only
to be charged under adult supervision.
1
Restraint Straps
Setup and Use
Securing your Infant
•Place your child in the seat. Position the restraint pad
between your child’s legs.
•Fasten the restraint straps to the restraint pad. Make sure
you hear a “click” on both sides.
•Check to be sure the restraint system is securely attached by
pulling it away from your child.The restraint system should
remain attached.
WARNING
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this reclined cradle on an elevated
surface, since child's movement may
cause bouncer to slide or tip over.
Use only on a floor.
Anchored End
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion),
since seat can tip over and cause
suffocation in soft surfaces.
• Always use the restraint system.
• Never leave the child unattended.
• Never use as a car seat.
Free End
TIGHTEN
Anchored End
• Never use the toy bar as a handle.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
Free End
LOOSEN
2
To tighten the restraint straps:
•Feed the anchored end of the restraint strap up through the
buckle to form a loop Ạ. Pull the free end of the restraint
strap ạ.
To loosen the restraint straps:
•Feed the free end of the restraint strap up through the buckle
to form a loop Ạ. Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the
restraint strap to shorten the free end of the restraint strap ạ.
7
Adjustable Pillow
Soothing Unit and Toybar
Pillow Strap
Power SSwitch
•Make sure your child is properly secured in the seat.
Soothing Unit
•Slide the power switch to: Vibrations or Off.
IMPORTANT! Low battery power causes this product to
operate erratically: no vibrations and the product may not turn
off. Remove and discard the battery and replace with a new
“D”(LR20) alkaline battery.
1
Toy Bar
•Pull the ring on the centre toy for a delightful tune!
•Place the pillow on the strap and press into place.
Hint: You can move the pillow up or down for
baby's comfort.
Care
•The pad and adjustable pillow are machine washable. Before
washing, fasten the strap to the back of the pad.Wash them
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
•To remove the pad: First remove the bottom pocket of the
pad. Then, remove the upper pad flap. To replace the pad,
refer to Assembly steps 7 and 8.
•The frame, toy bar and toys may be wiped clean using a mild
cleaning solution and damp cloth. Do not immerse the toy bar.
Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue.
BACK VIEW
2
•If you'd like to use the bouncer without the pillow, simply
pull to remove. Fasten the strap to the back of the bouncer.
•Before disposing of the flower toy, please remove the batteries.
•Loosen the screw in the battery compartment door. Remove
and dispose the batteries safely.
8
|