Epson Stylus CX4800 User Manual

®
Epson Stylus CX4200 Series/CX4800 Series  
Quick Guide  
Basic Copying, Printing, and Scanning  
Maintaining Your Epson Stylus CX All-in-One  
Solving Problems  
Introduction  
After you have set up your Epson Stylus® CX4200 Series or Epson Stylus®  
CX4800 Series all-in-one as described on the Start Here sheet, turn here to:  
Load paper  
Make a quick copy of a document or photo  
Print photos stored on a memory card (Epson Stylus CX4800 Series only)  
Print photos directly from your camera (both the Epson Stylus CX4200 Series  
and Epson Stylus CX4800 Series)  
Get the basic steps for printing from your computer  
Start scanning a document or photo, including restoring a color photo as you  
scan  
Perform routine maintenance  
Solve simple problems  
This book tells you how to do most of these things without ever turning on your  
computer! Of course your Epson Stylus CX can do lots more when you connect it  
to your Windows® or Macintosh® computer. For additional instructions, see the  
on-screen User’s Guide by selecting the icon for it on your desktop.  
Please follow these guidelines as you read your Epson Stylus CX instructions:  
Warning:  
Warnings must be followed carefully to avoid bodily injury.  
Caution:  
Cautions must be observed to avoid damage to your equipment.  
Note:  
Notes contain important information about your Epson Stylus CX.  
Tip:  
Tips contain hints for better copying, scanning, and printing.  
Note:  
The illustrations in this guide show the Epson Stylus CX4800 Series all-in-one and  
its software, but the instructions are the same for the Epson Stylus CX4200 Series  
all-in-one except where noted.  
Introduction 3  
Loading Paper  
Follow the steps here to load paper in your  
Epson Stylus CX all-in-one.  
1. Open the paper support and output tray,  
then slide out the extensions.  
2. Flip the feeder guard forward. Then slide  
the left edge guide to the left.  
3. Insert the paper, printable side up, against the right edge guide. Always load it  
short edge first, even for landscape printing.  
The printable side is often whiter or brighter than the other side.  
Narrow paper  
Place paper  
beneath the  
tabs  
4 Loading Paper  
 
You can load up to 100 sheets of plain paper and up to 20 sheets of photo  
paper. (See the User’s Guide for capacity guidelines on other paper types.)  
Note:  
The type of paper you choose affects the way your printout looks, so be sure to  
select the correct paper for your job. If you are just making a copy or printing a  
rough draft of an image, plain paper is fine. However, for the best results, you’ll  
want to use one of Epsons special ink jet papers designed for your printer. For  
example, your photos will look great printed on Epson Premium Glossy Photo  
Paper. See page 25 for more information.  
4. Slide the left edge guide against the left edge of the paper (but not too tightly).  
Then flip the feeder guard back.  
5. Make sure the paper thickness lever is set down to the m L position.  
Loading Paper 5  
Copying a Photo or Document  
Follow the instructions in this section to:  
Position your photo or document correctly on the glass (see below)  
Make copies of a photo or document (on page 8)  
Placing the Original on the Glass  
1. Open the document cover and place your original face-down on the glass, in  
the upper left corner. Move your original about 0.04 inch (1 mm) away from  
the top and left edges so all of it will be copied.  
Move the original about 0.04 inch (1 mm) away  
from the top and left edges to avoid cropping  
2. Close the cover gently so you don’t move the original.  
Caution:  
Never open the document cover beyond where it stops and do not place heavy  
objects on top of the Epson Stylus CX all-in-one.  
6 Copying a Photo or Document  
 
If you need to copy or scan a thick or large document, you can remove the  
document cover. Just open it and pull it straight up.  
If you need to press the document flat while you copy or scan it, do not press too  
hard and be careful not to move it.  
Caution:  
Do not use excessive force on the document cover, and do not twist it. You may  
damage the document cover.  
When you are done, replace the document cover by inserting the tabs back into  
the slots.  
Copying a Photo or Document 7  
 
Copying  
You can make copies using either letter-size (8.5×11-inch) plain paper, or  
letter-size, 4×6-inch, or 5×7-inch photo paper.  
Copying a Document  
1. Make sure the Epson Stylus CX is turned on.  
2. Place the document on the glass as described on  
page 6. Be sure to close the document cover.  
3. Load up to 100 sheets of letter-size plain paper.  
(See page 4 if you need instructions.)  
4. Press the Copy button until you see the desired  
number of copies in the Copy window. You can  
select up to 9 copies at a time this way.  
To make more than 9 copies, see page 10.  
5. Press the paper type button to select Plain Paper.  
The light indicates which type is selected.  
6. Press the paper size button to select Letter.  
7. If you want your copies automatically reduced or  
enlarged to fit the loaded paper size, press the  
Fit to Page button.  
8. To make a color copy, press the x Start Color  
button.  
To make a black and white copy, press the  
x Start B&W button.  
The P On light flashes and after a moment the Epson  
Stylus CX starts printing.  
If you need to stop copying at any time, just press the y Stop button. Do not pull  
out paper that is being printed; it will be ejected automatically to the output tray.  
Note:  
The copies may not be exactly the same size as the original.  
8 Copying a Photo or Document  
 
Copying a Photo  
1. Make sure the Epson Stylus CX is turned on.  
2. Place the photo on the glass as described on page 6.  
Be sure to close the document cover.  
3. Load up to 20 sheets of letter-size, 4 × 6-inch, or 5 × 7-inch photo paper. (See  
page 4 if you need instructions.)  
4. Press the Copy button until you see the correct  
number of copies in the Copy window. You can  
select up to 9 copies at a time this way.  
To make more than 9 copies, see page 10.  
5. Press the paper type button to select Photo Paper.  
6. Press the paper size button to select Letter, 4”x6,  
or 5”x7.  
7. If you want borderless photos (printed without a  
white border), press the Fit to Page button.  
Otherwise, photos are printed with a .06-inch  
(1.5 mm) border.  
8. To make a color copy, press the x Start Color  
button.  
To make a black and white copy, press the  
x Start B&W button.  
The P On light flashes and after a moment the Epson Stylus CX starts printing.  
If you need to stop copying at any time, just press the y Stop button. Do not pull  
out paper that is being printed; it will be ejected automatically to the output tray.  
Note:  
The copies may not be exactly the same size as the original.  
Copying a Photo or Document 9  
Making 10 or More Copies  
1. Make sure the Epson Stylus CX is turned on.  
2. Place the photo on the glass as described on page 6. Be sure to close the  
document cover.  
3. Press the Copy button until you see “” in the Copy window. This tells the  
Epson Stylus CX to print up to 100 copies.  
4. Load enough paper for the number of copies (up to 100) you want to make.  
For example, to print 12 copies, load 12 sheets of paper.  
5. Press the paper type button to select Plain Paper or Photo Paper.  
6. Press the paper size button to select Letter, 4”x6”, or 5”x7”.  
7. Press the x Start Color or x Start B&W button.  
The Epson Stylus CX makes copies until it runs out of paper. Then the red  
b Error light comes on.  
8. To make more copies, load more paper and press the x Start Color or  
x Start B&W button to resume.  
If you don’t need any more copies, press the y Stop button.  
Note:  
When making a lot of copies, it is a good idea to remove the printed copies from the  
output tray after every 10 sheets or so.  
Speeding Up Printing  
If you want to make a copy quickly and do not need high quality, you can print a  
“draft” copy. The print quality is reduced, but the copy is printed faster.  
1. Load plain, letter-size paper and select Plain Paper and Letter size on the  
control panel.  
2. When you are ready to copy, press and hold down the y Stop button, then  
press the x Start Color button (to copy in color) or the x Start B&W  
button (to copy in black and white). When the P On light starts flashing,  
release both buttons.  
10 Copying a Photo or Document  
 
Printing From a Memory Card  
(Epson Stylus CX4800 Series  
Only)  
The Epson Stylus CX4800 Series all-in-one lets you print color photos directly  
from your digital camera’s memory card; just insert it into a memory card slot on  
the Epson Stylus CX4800 Series and you’re ready to print.  
If your digital camera supports DPOF (Digital Print Order Format), you can  
pre-select the photos you want to print while the card is still in the camera. Then,  
when you insert the card in the Epson Stylus CX4800 Series, it knows which  
photos to print and how many copies of each.  
See these sections:  
For instructions on copying memory card files between your Epson Stylus  
CX4800 Series and a computer or other device, see the User’s Guide.  
Printing From a Memory Card (Epson Stylus CX4800 Series Only) 11  
Compatible Cards and Image Formats  
You can use the following types of cards with your Epson Stylus CX4800 Series:  
Right slot  
Slot  
Type of card  
Right slot  
CompactFlashTM  
MicrodriveTM  
Left slot  
SmartMediaTM  
Memory StickTM  
MagicGateTM Memory Stick  
MagicGate Memory Stick Duo*  
MultiMediaCard  
Memory card access light  
Left slot  
Memory Stick DuoTM  
*
Memory Stick PROTM  
Memory Stick Pro DuoTM  
SDTM Card  
*
miniSDTM Card*  
xD-Picture Card  
* Adapter required  
The Epson Stylus CX4800 Series supports image files that meet the following  
requirements:  
Media format  
File format  
DCF version 1.0 or 2.0 compliant*  
JPEG, DOS FAT (FAT 12 or 16, one partition) taken with a DCF  
version 1.0 or 2.0 compliant digital camera  
Supports Exif version 2.21  
80 × 80 pixels to 9200 × 9200 pixels  
Up to 999  
Image size  
Number of files  
*
DCF is the “Design rule for Camera File system” standard  
12 Printing From a Memory Card (Epson Stylus CX4800 Series Only)  
     
Inserting the Card  
1. Make sure the Epson Stylus CX4800 Series all-in-one is turned on.  
Note:  
When you print directly from a memory card, it is best if the Epson Stylus CX4800  
Series is not connected to your computer (or your computer should be turned off).  
2. Open the memory card door.  
3. Make sure the memory card access light is off and that no cards are in any of  
the slots. Then insert your card into the correct slot. (See page 12 for details.)  
Insert just one card at a time  
Right slot  
Left slot  
Memory card access light  
The memory card access light flashes and then stays on.  
4. Close the memory card door. Now you can:  
Print an index sheet so you can select which photos to print (page 14)  
Print all the photos on the card (page 17)  
Print photos pre-selected on your camera using DPOF (page 17)  
When you want to remove the card, make sure the memory card access light is not  
flashing, then pull the card straight out of its slot.  
Printing From a Memory Card (Epson Stylus CX4800 Series Only) 13  
   
Note:  
You can print only in color when printing directly from a memory card; you cannot print  
in black and white.  
Caution:  
Do not remove the card or turn off the Epson Stylus CX4800 Series while the memory  
card access light is flashing; you may lose data on the card.  
Printing an Index Sheet to Select Photos  
You can print an index sheet (which is like a photographer’s contact or proof sheet)  
to see small “thumbnail” images of all the pictures on your card. Then you mark  
the pictures on the index sheet that you want to print, scan the sheet, and let the  
Epson Stylus CX4800 Series automatically print the selected photos.  
Printing the Index Sheet  
1. Make sure your Epson Stylus CX4800 Series is not connected to your  
computer (or your computer is turned off).  
2. Load several sheets of letter-size, plain paper. (Use only letter-size paper to  
print the index sheet.) Up to 30 images are printed on each page, so if there  
are more than 30 photos on the memory card, you’ll need enough sheets for  
all the index pages to be printed.  
3. Insert the memory card if it is not already in the slot (see  
4. Press the Memory Card button one or more times until  
the Print Index Sheet light comes on.  
5. Make sure Plain Paper and Letter are selected.  
14 Printing From a Memory Card (Epson Stylus CX4800 Series Only)  
 
6. Press the x Start Color button. The P On light flashes, and the Epson Stylus  
CX4800 Series starts printing the index sheet(s). (This may take a few  
minutes.)  
For multiple index sheets, the pages containing the most recent images are  
printed first. If you want to cancel printing more sheets, press the y Stop  
button.  
Now follow the instructions below to select which photos to print.  
Selecting Photos on the Index Sheet  
1. Once you have printed the index sheet, use a dark pen or pencil to fill in one  
of the ovals beneath each photo you want to print to indicate how many  
copies you want (1, 2, or 3).  
OK:  
No  
good:  
Make sure just one oval is filled in for each selected photo and mark the sheet  
carefully; once it has been scanned you will not be able to change your  
selections.  
Note:  
If you want one copy of all the photos on the index sheet, fill in the ALL oval at the  
top of the page.  
Printing From a Memory Card (Epson Stylus CX4800 Series Only) 15  
 
2. Place the index sheet face-down on the glass, in the upper left corner, so that  
the top of the sheet is aligned against the left edge of the glass.  
3. Close the document cover.  
4. Load up to 100 sheets of plain paper or up to 20 sheets of photo paper at a  
time (see page 4 for details). You can load more paper later as necessary to  
print all your selected photos.  
5. Make sure the Print From Index Sheet light is on.  
6. Select Plain Paper or Photo Paper (whichever you loaded).  
If you select Plain Paper, the photo(s) print with a white  
border. If you select Photo Paper, the photos print  
borderless, to the edge of the paper.  
7. Select Letter, 4”x6, or 5”x7for the paper size.  
8. Press the x Start Color button to start printing.  
Note:  
If you need to stop printing, press the y Stop button.  
9. When you are done printing, remove the memory card by  
pulling it straight out of its slot.  
16 Printing From a Memory Card (Epson Stylus CX4800 Series Only)  
Printing All Photos or DPOF Photos  
Follow the steps below to print one copy of each photo on the card or to print  
only those photos that were pre-selected with your camera’s DPOF feature.  
1. Insert the memory card (see page 13).  
2. Load up to 100 sheets of plain paper or up to 20 sheets of photo paper at a  
time (see page 4 for details). You can load more paper later as necessary to  
print all your photos.  
3. Press the Memory Card button until the Print All/DPOF/  
PictBridge light comes on.  
Note:  
If the memory card does not contain DPOF information, one  
copy of all the photos on the card will be printed.  
4. Select Plain Paper or Photo Paper (whichever you loaded).  
If you select Plain Paper, the photo(s) print with a white  
border. If you select Photo Paper, the photos print  
borderless, to the edge of the paper.  
5. Select Letter, 4”x6, or 5”x7for the paper size.  
6. Press the x Start Color button to start printing.  
Note:  
If you need to stop printing, press the y Stop button.  
7. When you are done printing, remove the memory card by pulling it straight  
out of its slot.  
Printing From a Memory Card (Epson Stylus CX4800 Series Only) 17  
 
Printing From a Digital  
Camera  
If your camera is PictBridge- or USB DIRECT-PRINT-compatible, you can  
print your JPEG photos by connecting your digital camera directly to your Epson  
Stylus CX4200 Series or Epson Stylus CX4800 Series all-in-one. Your photos  
must be sized from 80 × 80 pixels to 9200 × 9200 pixels.  
1. Make sure your Epson Stylus CX is not printing from a computer.  
2. If you’re using the Epson Stylus CX4800 Series, remove any memory cards  
from slots and press the Memory Card button until the Print All/DPOF/  
PictBridge light comes on.  
3. Load the type of paper you want to use (see page 4). Load enough sheets for  
the number of photos you’ll be printing.  
4. Select Plain Paper or Photo Paper (whichever you loaded). If you select  
Photo Paper, the photos print borderless, to the edge of the paper.  
5. Select Letter, 4”x6, or 5”x7for the paper size.  
6. Connect the USB cable that  
came with your camera to the  
USB connector on the front of  
your Epson Stylus CX.  
7. Turn on your camera and select  
the photos you want to print.  
Then adjust any necessary  
settings and print your photos as  
explained in your camera manual.  
Note:  
If your camera is not supported, a flashing P appears in the Copy window, and the  
b Error light flashes. (On the Epson Stylus CX4800 Series, the Print All/DPOF/  
PictBridge light also flashes.) Epson cannot guarantee the compatibility of any camera.  
Depending on the Epson Stylus CX settings and your digital camera settings, some  
combinations of paper type, size, and layout may not be supported. In addition, some of  
your digital camera settings may not be reflected in the printed output.  
18 Printing From a Digital Camera  
Printing From Your Computer  
This section describes the basic steps for printing a photo or document stored on  
your Windows or Macintosh computer.  
Note:  
For detailed instructions on printing, see the on-screen User’s Guide.  
Before you start, make sure you’ve installed your printer software and connected  
the Epson Stylus CX all-in-one to your computer as described on the Start Here  
sheet. Also be sure to use the right paper and select the correct paper type setting  
in the printer driver. (See page 25 for more information.)  
Follow the instructions in these sections:  
Printing in Windows  
1. Load paper (see page 4).  
2. Open the photo or document in your application program.  
3. Open the File menu and select Print. You see a window like this one:  
Select EPSON Stylus CX4200 Series  
or EPSON Stylus CX4800 Series  
Click here to open  
your printer software  
Printing From Your Computer 19  
 
4. Make sure Epson Stylus CX4200 Series or Epson Stylus CX4800 Series  
is selected, then click the Preferences or Properties button.  
(If you see a Setup, Printer, or Options button, click it. Then click  
Preferences or Properties on the next screen.)  
5. On the Main tab, select the basic print settings:  
Select the type of document you’re printing  
(choose Photo or Best Photo for pictures)  
Select your  
paper Type  
Select your  
paper Size  
Click here for  
borderless photos,  
after choosing  
paper Type  
Select your  
document  
Orientation  
Click here for more options  
Make sure you choose the correct paper Type setting for the paper you are  
using. See page 25 for details.  
Note:  
For more information about print settings, click the ? or Help button.  
20 Printing From Your Computer  
 
6. For more printing options, click the Advanced button. Then select the  
following settings as necessary:  
Select a color management method  
(To choose No Color Adjustment, click ICM first)  
Select Paper & Quality  
Options as necessary  
Select Print Options  
as necessary  
Click here if you want to see this Advanced  
screen each time you access your print settings  
Note:  
For more information about advanced settings, or instructions on saving them as a  
group so you can reuse them later, click ? or Help.  
7. If you want to change the layout settings, click the Page Layout tab and  
select settings as necessary.  
8. Click OK to save your settings, then click OK or Print to start printing. This  
window appears and shows the progress of your print job.  
Cancel printing  
Pause or resume  
printing  
Check remaining ink levels  
Printing From Your Computer 21  
Printing With Macintosh OS X  
If you’re using an OS X-compatible application, follow the steps below to print.  
1. Load paper (see page 4).  
2. Open the photo or document in your application.  
3. Select Page Setup from the File menu. Make the following settings:  
Select Stylus CX4200 or  
Stylus CX4800  
Select your Paper Size*  
Select your document  
or image orientation  
* For borderless printing, choose the (Sheet Feeder - Borderless) option in the  
Paper Size list for your paper size (US Letter, 8 x 10, 5 x 7, or 4 x 6).  
4. Click OK to close the Page Setup window.  
5. Select Print from the File menu. You see a window like this one:  
Select Stylus CX4200 or  
Stylus CX4800  
Select Print Settings  
22 Printing From Your Computer  
 
6. Choose Print Settings from the pop-up menu and select the following  
settings as necessary:  
Select your Media  
Type (see page 25)  
Select Color or  
Black ink  
Select higher quality  
or faster printing  
(if available)  
Select  
Automatic mode  
Note:  
For more information about printer settings, click the ? button.  
7. Depending on your settings, you can choose these other options from the  
pop-up menu:  
Copies & Pages: Select the number of copies you want, or a page range.  
Layout: Select page layout options.  
Output Options: Save your print job as a PDF file.  
Scheduler: Schedule your print job to print at a later time.  
Paper Handling: Select page printing options, such as Reverse print  
order.  
ColorSync or Color Management: Select ColorSync®or adjust the  
color controls, change the gamma setting, or turn off color adjustments in  
the printer software.  
Expansion: Reduce or enlarge the image size for borderless printing.  
Summary: View a list of all your selections.  
Printing From Your Computer 23  
 
8. Click the Advanced button to change additional settings.  
Select Print Quality  
and other options  
as necessary  
Note:  
For more information on advanced settings, or instructions on saving them as a  
group so you can reuse them later, click ?.  
9. Click Print.  
10. To monitor the progress of your print job, click the  
appears in the dock on the bottom of your desktop.  
If you’re using OS X 10.2.x, click the Print Center icon instead, then  
printer icon when it  
double-click Stylus CX4200 or Stylus CX4800 in the Printer List window.  
You see a screen like this:  
Pause printing  
Resume printing  
Cancel printing  
Select the  
print job  
11. When you’re finished, close the printer window or Print Center.  
24 Printing From Your Computer  
Using Special Papers  
You can purchase genuine Epson ink and paper from an authorized Epson reseller.  
To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To  
call 800-463-7766 for reseller referral.  
Paper name  
Size  
Part number  
S041934  
Epson Ultra Premium Glossy Photo Paper  
Borderless 4 × 6 inches  
Letter (8.5 × 11 inches)  
Letter (8.5 × 11 inches)  
Borderless 4 × 6 inches  
Borderless 5 × 7 inches  
Borderless 8 × 10 inches  
Letter (8.5 × 11 inches)  
Letter (8.5 × 11 inches)  
Borderless 4 × 6 inches  
Letter (8.5 × 11 inches)  
S041935  
Epson Premium Bright White Paper  
Epson Premium Glossy Photo Paper  
S041586  
S041808/S041727  
S041464  
S041465  
S041286/S041667  
S041331  
Epson Premium Semigloss Photo Paper  
Epson Glossy Photo Paper  
S041809  
S041141/S041649/  
S041272/S041271  
Epson Matte Paper Heavyweight  
Borderless 8 × 10 inches  
Letter (8.5 × 11 inches)  
Letter (8.5 × 11 inches)  
Letter (8.5 x 11 inches)  
Legal (8.5 x 14 inches)  
A4 (8.3 x 11.7 inches)  
S041467  
S041257  
S041568  
S041062  
S041067  
S041061  
Epson Double-Sided Matte Paper  
Epson Photo Quality Ink Jet Paper  
Select the correct Type (see page 20) or Media Type (see page 23) setting in your  
printer software:  
For this paper  
Select this setting  
Epson Ultra Premium Glossy Photo Paper  
Plain paper or Epson Premium Bright White Paper  
Envelopes  
Ultra Premium Glossy Photo Paper  
Plain Paper/Bright White Paper  
Envelope  
Epson Matte Paper Heavyweight  
Epson Double-Sided Matte Paper  
Epson Photo Quality Ink Jet Paper  
Matte Paper - Heavyweight  
Epson Premium Glossy Photo Paper  
Epson Premium Semigloss Photo Paper  
Epson Glossy Photo Paper  
Premium Glossy Photo Paper  
Premium Semigloss Photo Paper  
Glossy Photo Paper  
Printing From Your Computer 25  
   
Scanning a Photo or Document  
You can use your Epson Stylus CX all-in-one to scan a photo or document and  
save it on your computer or other device, or to fax or e-mail it to someone else.  
You can even automatically restore faded color photographs as you scan. See  
page 28 for details.  
The EPSON Scan software provides three scanning modes for progressive levels of  
control over your scanned image:  
Full Auto Mode scans quickly and easily using automatic settings.  
Home Mode previews your image and provides automatic image  
adjustments, cropping tools, and preset options for various types of scans.  
Professional Mode previews your image and lets you manually configure  
your scan settings with a full array of tools.  
Basic Scanning  
You can scan from any TWAIN-compliant application—such as ArcSoft  
PhotoImpression —using EPSON Scan. Or you can start EPSON Scan directly  
from your computer and save your image to a file.  
1. Open the document cover and place your original face-down on the glass, in  
the upper left corner. Move your original about 0.04 inch (1 mm) away from  
the top and left edges so all of it will be scanned.  
Move the original about 0.04 inch  
(1 mm) away from the top and  
left edges to avoid cropping  
26 Scanning a Photo or Document  
Note:  
If you need to scan a thick document, you can remove the document cover; see  
2. Close the cover gently so you don’t move the original.  
3. Do one of the following to start EPSON Scan:  
Windows: Double-click the EPSON Scan icon on your desktop.  
Macintosh: Double-click EPSON Scan in the Applications folder.  
If you are scanning from an application, start your application. Then  
open the File menu, choose Import or Acquire, and select Epson Stylus  
CX4200 Series or Epson Stylus CX4800 Series.  
You see the EPSON Scan standby  
window:  
4. If the Mode setting in the upper right  
corner is set to Full Auto Mode, click the  
Scan button.  
Note:  
If you want to automatically restore a color  
photo as you scan, click the Customize  
button and see page 28 for instructions.  
If you are in Home or Professional Mode,  
you see a different EPSON Scan settings  
window. (You can change the mode using  
the Mode selector in the upper right  
corner. For details, see the on-screen User’s Guide.)  
5. You see the File Save Settings window:  
Choose the location where you want to  
save your scanned file and type a name for  
it in the Prefix box. Select a file format in  
the Image Format box.  
6. Click OK. The image is scanned and you  
see its icon in an open folder.  
Scanning a Photo or Document 27  
Restoring Color in Faded Photos  
You can automatically transform an old, faded, or badly exposed color photo into  
one with true-to-life color and sharpness as you scan. Look for the Color  
Restoration option in EPSON Scan’s Full Auto, Home, and Professional Mode  
screens:  
Full Auto Mode  
Click the Customize button,  
click the Color Restoration  
button, click OK, and click  
Scan.  
Home Mode  
Professional Mode  
Preview your image, click the Color  
Restoration button, and click Scan.  
Preview your image, scroll down to the  
Adjustments area, click the Color  
Restoration button, and click Scan.  
Note:  
For details on using Home or Professional Mode, or for more information about Full  
Auto Mode settings, see the on-screen User’s Guide. You can also click Help on the  
EPSON Scan screen for information about all the available settings.  
28 Scanning a Photo or Document  
 
Maintaining Your Epson  
Stylus CX All-in-One  
If you notice a decline in print quality, follow the instructions in this chapter for:  
Checking the Print Head Nozzles and Ink  
If your printouts are faint or have gaps in them, some of the nozzles in the print  
head may be clogged or ink may be running low in one or more of the ink  
cartridges. Follow the steps below to check the print head nozzles and remaining  
ink levels using the control panel.  
1. Turn off the Epson Stylus CX.  
2. Load letter-size paper in the sheet feeder.  
3. Press the B ink and P On buttons together and hold them down for about  
3 seconds. The Epson Stylus CX turns on and prints a test pattern. It also  
shows the percentage of ink left in each cartridge:  
Print head does  
not need to be  
cleaned yet:  
Print head needs  
to be cleaned:  
If the pattern does not look good, try cleaning the print head as described on the  
next page.  
Note:  
You can also check the ink level using Status Monitor 3; see the on-screen  
User’s Guide.  
Maintaining Your Epson Stylus CX All-in-One 29  
   
Cleaning the Print Head  
If your printouts are unexpectedly light or faint, or you notice light or dark bands  
across your printout, you may need to clean the print head. This unclogs the  
nozzles so they can deliver ink properly. Run a nozzle check as described on  
page 29 to see if the print head needs cleaning.  
Note:  
Print head cleaning uses ink, so clean it only if quality declines and the nozzle check  
indicates that the print head needs to be cleaned.  
If the red B ink light comes on or flashes, you cannot clean the print head. In this case,  
replace the appropriate ink cartridge first; see page 31.  
1. Make sure the Epson Stylus CX is on and the B ink light is off.  
2. Hold down the B ink button for 3 seconds until the P On light starts  
flashing. The Epson Stylus CX runs a head cleaning cycle and the P On light  
flashes.  
Caution:  
Never turn off the Epson Stylus CX while head cleaning is in progress. You may  
damage it.  
3. When the P On light stops flashing, run a nozzle check (as described on  
page 29) to verify that the print head is clean.  
4. If there are still gaps or lines, or the test patterns are faint, run another  
cleaning cycle and check the nozzles again.  
Note:  
If you don’t see any improvement after cleaning the print head four or five times,  
turn off the Epson Stylus CX and wait overnight. This lets any dried ink soften. Then  
try cleaning the print head again. If quality still does not improve, one of the ink  
cartridges may be old or damaged and needs to be replaced; see page 31.  
Tip:  
If you do not use your Epson Stylus CX often, it is a good idea to print a few pages at  
least once a month to maintain good print quality.  
30 Maintaining Your Epson Stylus CX All-in-One  
   
Replacing Ink Cartridges  
When the red B ink light starts flashing, one or more cartridges are low on ink.  
When the red B ink light stays on, you need to replace the cartridge(s). You’ll also  
see a message on your screen when you print, telling you which cartridge is low or  
empty. (You cannot print when a cartridge is empty.)  
You can purchase genuine Epson ink and paper from an authorized Epson reseller.  
To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To  
call 800-463-7766 for reseller referral. Use these part numbers when you order or  
purchase new ones.  
Color  
Part number  
T060120  
Black  
Cyan  
T060220  
Magenta  
Yellow  
T060320  
T060420  
Caution:  
Leave the empty cartridge installed until you have obtained a replacement, or the ink  
remaining in the print head nozzles may dry out.  
We recommend that you use genuine Epson cartridges. The use of other products may  
more cartridge information. Yields vary considerably based on images printed, print  
settings, paper type, frequency of use, and temperature. The printer ships with full  
cartridges and part of the ink from the first cartridges is used for priming the printer.  
1. Make sure the Epson Stylus CX is on.  
2. Make sure that the document cover is  
closed, then open the scanner.  
Caution:  
Do not open the scanner when the document  
cover is open.  
Maintaining Your Epson Stylus CX All-in-One 31  
   
3. Press and release the B ink button. The P On and B ink lights flash.  
If one of the cartridges is low or empty, the Epson Stylus CX moves that  
cartridge to the _ ink out mark. Go to step 4.  
If no cartridges are low or empty, the ink cartridge holder moves to the ink  
replacement position. Go to step 5.  
Note:  
Do not hold down the B ink button for more than 3 seconds or the printer will start  
to clean the print head.  
Caution:  
Do not move the print head by hand; this may damage the Epson Stylus CX.  
Always press the B ink button to move it.  
4. Press the B ink button again.  
If more than one cartridge is empty or low, the next cartridge moves to  
the _ ink out mark.  
Once the Epson Stylus CX identifies all of the empty or low ink  
cartridges, the print head moves to the ink cartridge replacement position.  
32 Maintaining Your Epson Stylus CX All-in-One  
 
5. Open the cartridge cover, then squeeze the tab at the back of the cartridge and  
lift it straight out. Dispose of it carefully. Do not take the used cartridge apart  
or try to refill it.  
Warning:  
If ink gets on your hands, wash them thoroughly with soap and water. If ink gets  
into your eyes, flush them immediately with water.  
6. Before you open the new ink cartridge package, shake it four or five times.  
Then remove it from the package.  
Caution:  
Do not remove or tear the label on the cartridge;  
otherwise, ink will leak.  
Do not touch the green chip on the front of the cartridge.  
This can damage the ink cartridge.  
Maintaining Your Epson Stylus CX All-in-One 33  
 
7. Place the new ink cartridge into the cartridge holder and push it down until it  
clicks into place.  
8. Replace any other cartridges that need to be replaced.  
9. Close the ink cartridge cover and press it until it clicks into place.  
10. Close the scanner.  
34 Maintaining Your Epson Stylus CX All-in-One  
11. Press the B ink button. The Epson Stylus CX begins charging ink and the  
P On light starts flashing. This takes about one minute. When it’s finished,  
the P On light stops flashing and remains on, and the B ink light goes out.  
Caution:  
Never turn off the Epson Stylus CX while the P On light is flashing or you’ll waste  
ink.  
Note:  
If the B ink light stays on (not flashing), the ink cartridge may not be installed  
correctly. Press the B ink button again and reinstall the ink cartridge until it clicks  
into place.  
Maintaining Your Epson Stylus CX All-in-One 35  
Solving Problems  
If you have a problem with your Epson Stylus CX all-in-  
one, check the lights on the control panel and the number  
or letter in the Copy window to diagnose the cause.  
for basic troubleshooting suggestions, or double-click the  
User’s Guide icon on your computer desktop for more  
detailed help.  
See these sections:  
Error Indicators  
Copy window  
Light: status  
status  
Cause  
Solution  
P On: Flashing  
b Error: On  
No paper is loaded in  
the sheet feeder.  
Load paper in the sheet feeder.  
Then press x Start Color to  
continue or y Stop to cancel.  
Multiple pages have  
been fed into the  
sheet feeder.  
Remove and reload the paper.  
Then press x Start Color to  
continue or y Stop to cancel.  
b Error: Flashing  
B Ink: Flashing  
Paper is jammed.  
An ink cartridge is  
running low on ink.  
B Ink: On  
An ink cartridge is  
empty or not installed  
correctly.  
36 Solving Problems  
 
Copy window  
status  
Light: status  
Cause  
Solution  
b Error: Flashing  
1
A memory card is  
inserted that is not  
supported by the  
Epson Stylus CX4800  
Series.  
Remove the incompatible  
memory card; see page 12.  
Memory Card  
(all 3 lights):  
Flashing  
(Epson Stylus  
CX4800 Series  
only)  
The inserted memory  
card does not contain  
any valid images.  
See page 12 for a list of  
compatible card and image  
types.  
b Error: Flashing  
2
3
An index sheet was  
not recognized  
because it is not  
positioned correctly.  
Position the index sheet correctly  
on the glass, aligning the top of it  
with the left edge of the glass.  
Then press x Start Color to  
continue or y Stop to cancel.  
Print From  
Index Sheet:  
Flashing  
(Epson Stylus  
CX4800 Series  
only)  
The index sheet is  
marked incorrectly.  
(No marks are  
Remove the index sheet, mark it  
correctly, and try again; see  
detected or the sheet  
includes more than  
one mark for an  
image.)  
4
The index sheet does  
not match the photos  
on the memory card.  
Remove the memory card and  
insert the card used to print the  
index sheet (see page 13 for  
instructions)—or place the  
correct index sheet on the glass.  
Then press x Start Color to  
continue or y Stop to cancel.  
b Error: Flashing  
fast  
H
The paper thickness  
lever is set to the  
^ H position.  
If you have set the lever to the  
^ H position because you are  
printing envelopes, press  
x Start Color to continue.  
Otherwise, set the lever to the  
m L position.  
b Error: On  
B Ink: On  
E
E
An Epson Stylus CX  
part needs to be  
replaced.  
Contact your local authorized  
servicer or contact Epson for a  
referral; see page 40.  
All other lights:  
Flashing  
All lights:  
Flashing  
There is a problem  
with the Epson Stylus then back on. If the error does  
Turn the Epson Stylus CX off and  
CX.  
not clear, contact your local  
authorized servicer or contact  
Epson for a referral; see page 40.  
Solving Problems 37  
Problems and Solutions  
Check the solutions below if you’re having trouble using your Epson Stylus CX all-  
in-one.  
Copying Problems  
Make sure your original is positioned in the top left corner of the glass. Place  
it 0.04 inch (1 mm) from the edges to avoid cropping.  
Make sure your paper is loaded short edge first and is positioned against the  
right edge guide with the left edge guide against its left side. Don’t load paper  
above the arrow mark inside the left edge guide.  
Paper Feeding Problems  
If paper doesn’t feed, remove it from the sheet feeder. Flip through the stack to  
separate the sheets a little. Then reload the paper against the right edge guide,  
and slide the left edge guide against the paper (but not too tightly). Make sure  
the paper is not in front of the feeder guard.  
Do not load too many sheets at once (up to 20 sheets of photo paper and 100  
sheets of plain paper). See the User’s Guide for more information.  
If paper is jammed, the red b Error light flashes. Follow these steps to clear  
the jam:  
1. Press the x Start Color button to eject the jammed paper. If the jammed  
paper is not ejected, go to the next step.  
2. If the paper is stuck near the sheet feeder or output tray, gently pull it out.  
If the paper is stuck inside the Epson Stylus CX, press the P On button  
to turn it off. Open the scanner and remove any paper inside, including  
any torn pieces. Do not pull it backward however; this can damage the  
sheet feeder. Close the scanner, then turn the Epson Stylus CX back on.  
38 Solving Problems  
   
Print Quality Problems  
If you have any problems with the copy or print quality, try these solutions:  
Make sure the document is placed flat against the document table glass and  
the Epson Stylus CX is not tilted or placed on an uneven surface.  
Load the paper printable side up (usually the whiter, brighter, or glossy side).  
Make sure your paper isn’t damp or curled.  
Use a support sheet with special paper or load your paper one sheet at a time.  
Remove sheets from the output tray so not too many collect at a time.  
Make sure the type of paper you loaded matches the paper size and paper type  
settings on the control panel or in your printer software (see page 25).  
For the best print quality, use Epson special paper (see page 25) and genuine  
Epson ink cartridges (see page 31).  
Set the paper thickness lever to the m L position for most paper types. If you  
are printing on envelopes, set the lever to the ^ H position.  
If you notice light or dark bands across your printouts or they are too faint,  
you may need to clean the print head. This unclogs the nozzles so they can  
deliver ink properly. Run a nozzle check as described on page 29 to see if the  
print head needs cleaning.  
Clean the print head as described on page 30.  
If you notice jagged vertical lines, you may need to align the print head. See  
your User’s Guide for instructions.  
The ink cartridges may be old or low on ink; see page 31 for instructions on  
replacing an ink cartridge.  
If a dotted line appears in the image, clean the scanner glass with a soft, dry,  
lint-free cloth (paper towels are not recommended), or use a small amount of  
glass cleaner on a soft cloth, if necessary. Don’t spray glass cleaner directly  
on the glass.  
Solving Problems 39  
Where To Get Help  
Epson provides technical assistance 24 hours a day through the electronic support  
services and automated telephone services listed in the following table.  
Service  
Access  
World Wide  
Web  
From the Internet, you can reach Epson Support at  
http://support.epson.com. At this site, you can download drivers and  
other files, look at product documentation, access troubleshooting  
information, and receive technical advice through e-mail.  
Automated  
Telephone  
Services  
A variety of automated help services are available 24 hours a day, seven  
days a week. To use these services, you must have a touch tone  
telephone and call (800) 922-8911. Your Epson SoundAdviceSM Express  
Code is 70660. Use this code to quickly select the Epson Stylus CX4200  
Series or Epson Stylus CX4800 Series in SoundAdvice.  
To speak to a technical support representative, dial:  
U.S.: (562) 276-4382, 6 AM to 6 PM, Pacific Time, Monday through Friday  
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday  
Toll or long distance charges may apply. Before you call, please have the following  
information ready:  
Product name (Epson Stylus CX4200 Series or Epson Stylus CX4800 Series)  
Product serial number (located on the back)  
Proof of purchase (such as a store receipt) and date of purchase  
Computer configuration  
Description of the problem  
You can purchase genuine Epson ink and paper from an authorized Epson reseller.  
To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To  
call 800-463-7766 for reseller referral.  
Other Software Technical Support:  
Software  
Telephone/Fax  
Online and E-mail  
ArcSoft  
PhotoImpression  
(510) 440-9901  
8:30 AM—5:30 PM, Pacific  
Time, Monday—Friday  
Fax: (510) 440-1270  
40 Solving Problems  
 
Notices  
Important Safety Instructions  
Before using your Epson Stylus CX all-in-one, read and follow these safety instructions:  
Be sure to follow all warnings and instructions marked on the Epson Stylus CX.  
Use only the type of power source indicated on the Epson Stylus CX label.  
Use only the power cord that comes with the Epson Stylus CX. Use of another cord  
may cause fires or shock. Do not use the cord with any other equipment.  
Place the Epson Stylus CX near a wall outlet where the plug can be easily unplugged.  
Placez l’imprimante près d’une prise de contacte où la fiche peut être débranchée  
facilement.  
Do not let the power cord become damaged or frayed.  
If you use an extension cord with the Epson Stylus CX, make sure the total ampere  
rating of the devices plugged into the extension cord does not exceed the cord’s  
ampere rating. Also, make sure the total ampere rating of all devices plugged into the  
wall outlet does not exceed the wall outlet’s ampere rating.  
Avoid locations that are subject to rapid changes in heat or humidity, shocks or  
vibrations, or dust.  
Leave enough room around the Epson Stylus CX for sufficient ventilation. Do not  
block or cover openings in the Epson Stylus CX case or insert objects through the  
slots.  
Do not place the Epson Stylus CX near a radiator or heating vent or in direct  
sunlight.  
Place the Epson Stylus CX on a flat, stable surface that extends beyond its base in all  
directions. It will not operate properly if it is tilted or at an angle.  
Make sure the back of the Epson Stylus CX is at least 3.9 inches (10 cm) away from  
the wall.  
Do not open the scanner section while the Epson Stylus CX is copying, printing, or  
scanning.  
Do not spill liquid on the Epson Stylus CX.  
Except as specifically explained in your documentation, do not attempt to service the  
Epson Stylus CX yourself.  
Notices 41  
Unplug the Epson Stylus CX and refer servicing to qualified service personnel under  
the following conditions: if the power cord or plug is damaged; if liquid has entered  
the product; if the product has been dropped or the case damaged; if the product does  
not operate normally or exhibits a distinct change in performance. Adjust only those  
controls that are covered by the operating instructions.  
When storing or transporting the Epson Stylus CX, do not tilt it, stand it on its side,  
or turn it upside down; otherwise ink may leak from the cartridge.  
The lamp in this product contains mercury. Dispose of according to local, state, or  
federal laws.  
Ink Cartridge Safety Instructions  
Keep ink cartridges out of the reach of children and do not drink the ink.  
Be careful when you handle used ink cartridges; there may be ink remaining around  
the ink supply port. If ink gets on your skin, wash it off with soap and water. If it gets  
in your eyes, flush them immediately with water.  
Do not put your hand inside the Epson Stylus CX or touch any cartridges during  
printing.  
Install a new ink cartridge immediately after removing an empty one. Leaving  
cartridges uninstalled can dehydrate the print head and may prevent the Epson Stylus  
CX from printing.  
If you remove an ink cartridge for later use, protect the ink supply area from dirt and  
dust and store it in the same environment as the Epson Stylus CX. Note that there is  
a valve in the ink supply port, making covers or plugs unnecessary, but care is needed  
to prevent the ink from staining items that the cartridge touches. Do not touch the  
ink cartridge ink supply port or surrounding area.  
42 Notices  
ENERGY STAR Compliance  
As an ENERGY STAR Partner, Epson has determined  
that this product meets the ENERGY STAR guidelines  
for energy efficiency. The EPA ENERGY STAR office  
equipment program is a voluntary partnership with the  
computer and office equipment industry to promote  
the introduction of energy-efficient personal computers, monitors, printers, fax machines,  
and copiers in an effort to reduce air pollution caused by power generation.  
FCC Compliance Statement  
For United States Users  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio or  
television reception. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause interference to radio and television  
reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Notices 43  
WARNING  
The connection of a non-shielded equipment interface cable to this equipment will  
invalidate the FCC Certification of this device and may cause interference levels which  
exceed the limits established by the FCC for this equipment. It is the responsibility of the  
user to obtain and use a shielded equipment interface cable with this device. If this  
equipment has more than one interface connector, do not leave cables connected to  
unused interfaces. Changes or modifications not expressly approved by the manufacturer  
could void the user’s authority to operate the equipment.  
For Canadian Users  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
Declaration of Conformity  
According to 47CFR, Part 2 and 15 for: Class B Personal Computers and Peripherals;  
and/or CPU Boards and Power Supplies used with Class B Personal Computers:  
We:  
Located at:  
Epson America, Inc.  
MS 3-13  
3840 Kilroy Airport Way  
Long Beach, CA 90806  
Telephone: (562) 290-5254  
Declare under sole responsibility that the product identified herein, complies with 47CFR  
Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed is  
identical to the representative unit tested and found to be compliant with the standards.  
Records maintained continue to reflect the equipment being produced can be expected to  
be within the variation accepted, due to quantity production and testing on a statistical  
basis as required by 47CFR §2.909. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
Trade Name:  
Epson  
Type of Product: Multifunction printer  
Model:  
C231B (Epson Stylus CX4200 Series)  
C231A (Epson Stylus CX4800 Series)  
44 Notices  
Epson America, Inc., Limited Warranty  
What Is Covered: Epson America, Inc. (“Epson”) warrants to the original retail purchaser  
that the Epson printer covered by this limited warranty statement, if purchased and  
operated only in the United States or Canada, conforms to the manufacturer’s  
specifications and will be free from defects in workmanship and materials for a period of  
one (1) year from the date of original purchase. Epson also warrants that the consumable  
ink cartridges enclosed with the printer will perform to the manufacturer’s specified usage,  
which usage may expire before the expiration of the limited warranty for the Epson  
printer. For warranty service, you must provide proof of the date of original purchase.  
What Epson Will Do To Correct Problems: Should your Epson printer prove defective  
SM  
during the warranty period, please call the Epson Connection at (562) 276-4382 (U.S.)  
or (905) 709-3839 (Canada) for warranty repair instructions and return authorization. An  
Epson service technician will provide telephone diagnostic service to determine whether  
the printer requires service. If service is needed, Epson will, at its option, exchange or  
repair the printer without charge for parts or labor. If Epson authorizes an exchange for the  
defective unit, Epson will ship a replacement printer to you, freight prepaid, so long as you  
use an address in Canada or the U.S. (excluding Puerto Rico and U.S. Possessions).  
Shipments to other locations will be made freight collect. You are responsible for securely  
packaging the defective unit and returning it to Epson within five (5) working days of  
receipt of the replacement. Epson requires a debit or a credit card number to secure the  
cost of the replacement printer in the event that you fail to return the defective one. If your  
printer is being repaired, Epson will direct you to send your printer to Epson or its  
authorized service center, where the printer will be fixed and sent back to you. You are  
responsible for packing the printer and for all costs to and from the Epson authorized  
service center. When warranty service involves the exchange of the printer or a part, the  
item replaced becomes Epson property. The replacement printer or part may be new or  
refurbished to the Epson standard of quality, and, at Epson’s option, may be another  
model of like kind and quality. Epson’s liability for replacement of the covered printer will  
not exceed the original retail selling price of the covered printer. Exchange products and  
parts assume the remaining warranty period of your original product covered by this  
limited warranty.  
What This Warranty Does Not Cover: This warranty does not apply to refurbished or  
reconditioned products. This warranty covers only normal use in the United States and  
Canada. Using this product for continuous production or similar high duty purposes is  
not considered normal use; damage, maintenance or service from such use will not be  
covered under this warranty. This warranty is not transferable. This warranty does not  
cover any color change or fading of prints or reimbursement of materials or services  
required for reprinting. This warranty does not cover damage to the Epson product caused  
by parts or supplies not manufactured, distributed or certified by Epson. This warranty  
does not cover ribbons, ink cartridges or third party parts, components, or peripheral  
Notices 45  
devices added to the Epson product after its shipment from Epson, e.g., dealer or user-  
added boards or components. Epson is not responsible for warranty service should the  
Epson label or logo or the rating label or serial number be removed or should the product  
fail to be properly maintained or fail to function properly as a result of misuse, abuse,  
improper installation, neglect, improper shipping, damage caused by disasters such as fire,  
flood, and lightning, improper electrical current, software problems, interaction with non-  
Epson products, or service other than by an Epson Authorized Servicer. If a claimed defect  
cannot be identified or reproduced, you will be held responsible for the costs incurred.  
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN  
LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY,  
NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME  
LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF  
THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE  
LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS  
STATED HEREIN, ANY STATEMENT OR REPRESENTATIONS MADE BY ANY  
OTHER PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS  
WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS  
AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR  
DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY  
TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF  
WARRANTY OR ANY OTHER LEGAL THEORY.  
In Canada, warranties include both warranties and conditions.  
Some jurisdictions do not allow limitations on how long an implied warranty lasts, and  
some jurisdictions do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitations and exclusions may not apply to you. This warranty  
gives you specific legal rights and you may have other rights which vary from jurisdiction  
to jurisdiction.  
You can also write to:  
Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012  
46 Notices  
Copyright Notice  
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or  
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or  
otherwise, without the prior written permission of Seiko Epson Corporation. The information  
contained herein is designed only for use with this Epson product. Epson is not responsible for any  
use of this information as applied to other equipment.  
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or  
third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result  
of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to  
this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s  
operating and maintenance instructions.  
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any  
options or any consumable products other than those designated as Original Epson Products or  
Epson Approved Products by Seiko Epson Corporation.  
Responsible Use of Copyrighted Materials  
Digital cameras, scanners, and ink jet printers, like conventional photocopiers and cameras, can be  
misused by improper copying or printing of copyrighted material. While some countries’ laws  
permit limited copying of copyrighted material in certain circumstances, those circumstances may  
not be as broad as some people assume. Epson encourages each user to be responsible and respectful  
of the copyright laws when using digital cameras, scanners, and ink jet printers.  
Trademarks  
Epson and Epson Stylus are registered trademarks and Exceed Your Vision is a trademark of Seiko  
Epson Corporation.  
DURABrite is a registered trademark and Epson Connection, Epson Store, and SoundAdvice are  
service marks of Epson America, Inc.  
USB DIRECT-PRINTand the USB DIRECT-PRINT logo are trademarks of Seiko Epson  
Corporation. Copyright © 2002 Seiko Epson Corporation. All rights reserved.  
DPOFis a trademark of CANON INC., Eastman Kodak  
Company, Fuji Photo Film Co., Ltd. and Matsushita Electric  
Industrial Co., Ltd.  
SDis a trademark.  
Memory Stick, Memory Stick Duo, Memory Stick PRO, and  
Memory Stick PRO Duo are trademarks of Sony Corporation.  
xD-Picture Cardis a trademark of Fuji Photo Film Co.,Ltd.  
General Notice: Other product names used herein are for identification purposes only and may be  
trademarks of their respective owners. Epson disclaims any and all rights in those marks.  
© 2005 Epson America, Inc. 5/05  
Notices 47  
CPD-19831  
Printed in XXXXXX XX.XX-XX XXX  

Brother MFC 425CN User Manual
Brother MFC 9200C User Manual
Coleman 6151 707 User Manual
Danby DAC8006DE User Manual
Friedrich MR24C3E User Manual
GE General Electric Air Conditioner AST12 User Manual
Graco Baby Accessories PD241044B User Manual
Graco SnugRide 1778253 User Manual
Heat Controller Inc Air Conditioner SMH 18 User Manual
HP Hewlett Packard HP CLJ M375NW PRO 300 CE903A#BGJ User Manual