Canon PIXMA MP750 User Manual

Start Here  
Easy Setup Instructions  
6 Lower the lock lever.  
Click  
Thank you for purchasing the Canon PIXMA MP780/750. To prepare your machine for use, please follow these  
Easy Setup Instructions before referring to any other documentation.  
Lower the lock lever  
until you hear a click  
as it locks into place.  
IMPORTANT  
5 Install the ink tanks.  
Do not connect the USB cable until after the software is installed. See the rear side of this sheet for details.  
1 Prepare the ink tanks.  
Remove the orange-colored  
protective film. If it is not  
removed completely,  
1 Unpack and install the machine.  
Remove the protective cap  
and discard it.  
problems with printing  
may occur.  
Check the package contents.  
• Machine  
• Power cord  
• Print head  
• Telephone line  
Do not touch!  
2 Insert the ink tanks.  
Click  
MP780  
MP750  
• Ink tanks  
Black BCI-3eBK  
Black  
Cyan  
BCI-6BK  
BCI-6C  
Magenta BCI-6M  
Yellow BCI-6Y  
Push it in until locks  
into place.  
Good example  
Bad example: Tank 6BK is  
not fully inserted.  
Make sure to press it down  
firmly.  
• Easy Setup Instructions • Quick Start Guide  
• Setup CD-ROM  
3 Close the Inner Covers and the Scanning Unit.  
The Setup CD-ROM contains the MP Drivers, as well as the User's Guide, Software Guide and Photo  
Application Guide in electronic format. Please read these guides.  
Click  
• In this sheet, illustrations of MP780 are shown.  
• A printer cable is not included. You must purchase a USB cable (less than 16 3/8 ft.) to connect your  
machine to a computer.  
Click  
Pull the Scanning Unit Lever  
towards you to close the  
Scanning Unit.  
2 Connect the telephone line. (MP780 model only)  
Close the two Inner Covers.  
IMPORTANT  
Be sure to hold the Scanning Unit firmly with one hand.  
Connect the telephone line and any necessary external device.  
For details, see the Quick Start Guide.  
6 Load the paper.  
Connect external devices as follows:  
External device jack  
Telephone line jack  
1 Open the Auto Sheet Feeder.  
2 Load two sheets or more of letter-size plain paper.  
Telephone or answering machine  
(1) Open the Auto Sheet  
Telephone or  
answering machine  
Load the paper with the print side face up.  
Feeder.  
Telephone  
line  
Machine  
Pinch and adjust  
the paper guide  
to the width of  
the stack.  
Built-in computer modem and telephone  
Connect the telephone  
line cord to the wall jack.  
LINE TEL  
Computer  
Telephone  
Telephone  
line  
Machine  
You can connect an external  
device (telephone or answering machine) if necessary.  
(2) Pull out the Paper  
Support until it stops.  
3 Connect the power cord.  
Ensure the paper stack  
does not exceed the paper limit mark.  
1 Connect the power cord.  
7 Align the print head from the Operation Panel.  
1. Connect one end of the power cord to the rear of the machine.  
2. Connect the other end to the AC outlet.  
Be sure to align the print head to ensure print quality.  
2 If the message <PUT IN CARTRIDGE> appears, go to Step 4, "Install the print  
head."  
1 Press [OK] to start print head alignment.  
(1) This message appears.  
(2) Press [OK].  
(3) The machine will print  
the print head position  
pattern and automatically  
align the print head.  
4 Install the print head.  
ALIGN PRINT HEAD  
PRESS [OK]  
1 Press the Open Button to open the  
Lift the Scanning  
Unit.  
Press the Open Button.  
If this message  
Paper Output Tray. Then lift the  
does not appear  
after closing the  
Scanning Unit,  
see "Aligning  
The Print Head  
Automatically"  
in the Quick Start  
Guide.  
Scanning Unit until it locks into place.  
Click  
IMPORTANT  
Be sure to hold the Scanning Unit firmly with one  
hand.  
Pull  
the Scanning  
Unit Lever.  
2 Open the two Inner Covers.  
3 Raise the lock lever.  
(2) The Print Head Holder moves to the center.  
Touch only the lock lever!  
If the printed pattern matches the illustration, print head alignment is complete.  
(3) Install the print  
head here.  
You can change the language displayed on the LCD.  
For details, see "Selecting The Language For The LCD" in the Quick Start Guide.  
Raise this securely.  
(1) Open the two  
Inner Covers.  
You have completed installation and alignment.  
If you are connecting the machine to a computer for use, see the rear side of this sheet for  
instructions on installing the software.  
4 Prepare the print head.  
5 Insert the print head.  
(2) Push back.  
Do not touch!  
(1) Insert.  
Remove the protective cap and discard it.  
© 2004 Canon U.S.A., Inc., Canon and BCI are registered trademarks and PIXMA is a trademark of Canon Inc.  
All other products and brand names are registered trademarks or trademarks of their respective owners.  
Specifications subject to change without notice.  
HT7-0029-000-V.1.0  
xx2004A  
© CANON INC. 2004  
PRINTED IN CHINA  

Briggs Stratton Automobile Parts 406700 User Manual
Brother MFC 820CW User Manual
Cecilware Liquid Iced Tea Dispenser TT4 User Manual
Dacor WINESTEWARD EF24LBCSS User Manual
Epson Stylus CX6400 User Manual
Field Controls UV 18X User Manual
Friedrich HA12K34L User Manual
Haier AU092ABNCA User Manual
Honeywell Barcode Reader EGPWS User Manual
Human Touch Automobile Accessories HT 3300 User Manual