Quick Setup Guide
MFC-9460CDN
Start Here
Before using this machine for the first time, read this Quick Setup Guide to setup and install your machine.
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injuries.
WARNING
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injuries.
CAUTION
Unpack the machine and check the components
1
Installation CD-ROM,
Documentation CD-ROM
Accessory Order Form
Product Registration
Sheet
(USA only)
AC Power Cord
Basic User's Guide
Quick Setup Guide
Waste Toner Box
Belt Unit
(pre-installed)
(pre-installed)
Starter Toner Cartridges
(pre-installed)
Drum Unit
(pre-installed)
(Black, Cyan, Magenta and
Yellow)
Telephone Line Cord
Safety and Legal Booklet
USA/CAN Version 0
1
d
e
Hold the green handle of the drum unit a and
pull it out until it stops.
Remove the packing
material from the
machine
2
IMPORTANT
DO NOT connect the AC power cord yet.
a
Remove the packing tape from the outside of
the machine.
b
Open the MP tray a, and remove the plastic
sheet b from the MP tray support, then close
the MP tray.
Gently pull the orange packing material
towards the front of the machine to remove it.
c
Press the front cover release button and open
the front cover. Remove the silica gel pack a.
f
Remove the 4 orange packing pieces.
CAUTION
DO NOT eat Silica Pack. Discard immediately.
g
h
Push the drum unit firmly back into the
machine.
Close the front cover of the machine.
3
d
Put paper in the tray and make sure:
The paper is below the maximum paper
mark (bbb) a.
Load paper in the paper
tray
3
Over filling the paper tray will cause paper
jams.
a
b
Pull the paper tray completely out of the
machine.
The side to be printed on must be face down.
The paper guides touch the sides of the
paper so it will feed properly.
While pressing the green paper-guide release
lever a, slide the paper guides to fit the paper
size you are loading in the tray. Make sure that
the guides are firmly in the slots.
e
Put the paper tray firmly back in the machine.
Make sure that it is completely inserted into the
machine.
For more information about recommended
paper, see Recommended paper and print
media in the Basic User's Guide.
c
Fan the stack of paper well to avoid paper jams
and misfeeds.
4
IMPORTANT
The telephone line cord MUST be connected
to the jack on the machine marked LINE.
Connect the power cord
and telephone line
4
WARNING
IMPORTANT
DO NOT connect the interface
cable yet.
The machine must be grounded using a
3-prong plug.
Since the machine is grounded through the
power outlet, you can protect yourself from
potentially hazardous electrical conditions on
the telephone network by keeping the power
cord connected to your machine when you
connect it to a telephone line. Similarly, you
can protect yourself when you want to move
your machine by disconnecting the telephone
line first and then the power cord.
a
Connect the AC power cord to the machine,
and then plug it into an AC power outlet.
b
Remove the label covering the machine's
power switch, and then switch the machine on.
Note
If you are sharing one telephone line with an
external telephone, connect it as shown below.
Before you connect the external telephone,
remove the protective cap a from the EXT. jack
on the machine.
1
c
Connect the telephone line cord. Connect one
end of the telephone line cord to the jack on the
machine marked LINE and the other end to a
modular wall jack.
2
1
1 Extension telephone
2 External telephone
5
Note
Choose your language
(if needed)
If you are sharing one telephone line with an
external telephone answering machine, connect it
as shown below.
5
Before you connect the external telephone
answering machine, remove the protective cap a
from the EXT. jack on the machine.
a
b
Press Menu, 0, 0.
Press a or b to choose your language.
Press OK.
c
Press Stop/Exit.
1
Set the receive mode to External TAD if
you have an external answering machine.
Connecting an external TAD (telephone
answering device) in the Basic User's Guide.
6
Choose the correct Receive Mode
6
The correct Receive Mode is determined by the external devices and telephone subscriber services (Voice Mail,
Distinctive Ring, etc.) you have (or will be using) on the same line as the Brother machine.
Will you be using a Distinctive Ring number for receiving faxes?
Brother uses the term “Distinctive Ring” but telephone companies may have other names for this service such
as Custom Ringing, RingMaster, Personalized Ring, Teen Ring, Ident-A-Call, and Smart Ring. See Distinctive
Ring in the Basic User's Guide for instruction on setting up your machine using this feature.
Will you be using Voice Mail on the same telephone line as your Brother machine?
If you have Voice Mail on the same telephone line as your Brother machine, there is a strong possibility that
Voice Mail and the Brother machine will conflict with each other when receiving incoming calls. See Voice Mail
in the Basic User's Guide for instructions on setting up your machine using this service.
Will you be using a Telephone Answering Device on the same telephone line as your Brother machine?
Your external telephone answering device (TAD) will automatically answer every call. Voice messages are
stored on the external TAD and fax messages are printed. Choose External TAD as your receive mode. See
the instructions below.
Will you be using your Brother machine on a dedicated fax line?
Your machine automatically answers every call as a fax. Choose Fax Only as your receive mode. See the
instructions below.
Will you be using your Brother machine on the same line as your telephone?
Do you want to receive voice calls and faxes automatically?
The Fax/Tel receive mode is used when sharing the Brother machine and your telephone on the same line.
Choose Fax/Tel as your receive mode. See the instructions below.
Important Note: You cannot receive voice messages on either Voice Mail or an answering machine when
choosing the Fax/Tel mode.
Do you expect to receive very few faxes?
Choose Manual as your receive mode. You control the telephone line and must answer every call yourself.
See the instructions below.
For details, see Using receive modes in the Basic User's Guide.
a
b
Press Menu, 0, 1.
Press a or b to choose the receive mode.
Press OK.
c
Press Stop/Exit.
7
d
e
f
Enter the two digits for the day on the dial pad,
and then press OK.
Set the LCD contrast
(if needed)
7
02.Date&Time
03/XX/2011
If you are having difficulty reading the LCD, try
changing the contrast setting.
Day:25
Enter & OK Key
(e.g. Enter 2, 5 for 25th.)
a
b
Press Menu, 1, 6.
Press c to increase the contrast.
—OR—
Enter the time in 24-hour format on the dial
pad, and then press OK.
Press d to decrease the contrast.
Press OK.
02.Date&Time
03/25/2011
c
Press Stop/Exit.
Time:15:25
Set the date and time
Enter & OK Key
8
(e.g. Enter 1, 5, 2, 5 for 3:25 P.M.)
Press Stop/Exit.
The machine displays the time, and if you set up the
station ID the date and time will be added to each fax
you send.
a
b
Press Menu, 0, 2, 1.
Enter the last two digits of the year on the dial
pad, and then press OK.
02.Date&Time
Year:2011
Enter & OK Key
(e.g. Enter 1, 1 for 2011.)
c
Enter the two digits for the month on the dial
pad, and then press OK.
02.Date&Time
XX/XX/2011
Month:03
Enter & OK Key
(e.g. Enter 0, 3 for March.)
8
Press
key
One
time
Two
times
Three
times
Four
times
Five
times
Set your Station ID
2
3
4
5
6
7
8
9
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
A
D
G
J
9
The machine displays the date and time, and if you
set up the Station ID, it will add it to each fax you send.
L
M
P
T
O
R
V
Y
M
7
a
b
Press Menu, 0, 3.
T
9
Enter your fax number (up to 20 digits) on the
dial pad, and then press OK.
W
03.Station ID
For more details, see Entering text in the
Basic User's Guide.
e
Press Stop/Exit.
Fax:_
Note
Enter & OK Key
If you make a mistake and want to start again,
c
d
Enter your telephone number (up to 20 digits)
on the dial pad, and then press OK. (If your
telephone number and fax number are the
same, enter the same number again.)
(USA only) The Telephone Consumer Protection
Act of 1991 makes it unlawful for any person to
use a computer or electronic device to send any
message via a telephone fax machine unless
such messages clearly contain, in a margin at the
top or bottom of each transmitted page, or on the
first page of the transmission, the date and time it
is sent and an identification of the business or
other entity or other individual sending the
message and the telephone number of the
sending machines or such business, other entity
or individual. To program this information into
your machine, see Set the date and
03.Station ID
Fax:XXXXXXXXXXX
Tel:_
Enter & OK Key
Use the dial pad to enter your name (up to
20 characters), and then press OK.
03.Station ID
Fax:XXXXXXXXXXX
Tel:XXXXXXXXXXX
Name:_
Enter & OK Key
Note
• See the following chart for entering your name.
• If you need to enter a character that is on the
same key as the last character, press c to move
the cursor to the right.
• If you entered a letter incorrectly and want to
change it, press d or c to move the cursor to the
incorrect character, press Clear.
9
Fax Transmission Report
Set the telephone line
compatibility
10
12
Your Brother machine is equipped with a
If you are connecting the machine to a VoIP service
(over the Internet) you need to change the
compatibility setting.
Transmission Verification Report that can be used as
confirmation that you sent a fax. This report lists the
name or fax number of the receiving party, the date,
time, and duration of the transmission, the number of
pages transmitted, and whether or not the
transmission was successful. If you want to use the
Fax Transmission Report feature see Printing reports
in the Advanced User's Guide.
Note
If you are using an analog telephone line you can
skip this step.
a
b
Press Menu, 2, 0, 1.
Press a or b to choose Basic(for VoIP).
Press OK.
Set tone or pulse dialing
mode (Canada only)
11
c
Press Stop/Exit.
Your machine comes set for Tone dialing service. If
you have Pulse dialing service (rotary), you need to
change the dialing mode.
a
b
Press Menu, 0, 4.
Press a or b to choose Pulse (or Tone).
Press OK.
c
Press Stop/Exit.
10
Dial Prefix
Automatic Daylight
Savings Time
13
14
The dial prefix setting will automatically dial a
predefined number before every fax number you dial.
For example: If your phone system requires a 9 to dial
an outside number this setting will automatically dial 9
for every fax you send.
You can set the machine to change automatically for
daylight savings time. It will reset itself forward one
hour in the Spring and backward one hour in the Fall.
a
b
Press Menu, 0, 2, 2.
Press a or b to choose On (or Off).
Press OK.
a
b
Press Menu, 0, 5 (for Canada, press 6).
Enter the prefix number (up to 5 digits) on the
dial pad, and then press OK.
c
Press Stop/Exit.
Note
• You can use the number 0 to 9, #, l and !.
(Press Hook to display “!”.)
Set the Time Zone
• You cannot use ! with any other numbers or
characters.
15
• If your telephone system requires a timed break
recall (hookflash), press Hook to enter the
break.
You can set the time zone (not summer time but
standard time) on the machine for your location.
For example, the time zone for Eastern Time in the
USA and Canada is UTC-05:00.
• If the pulse dialing mode is on, # and l are not
available to use. (Canada only)
a
b
Press Menu, 0, 2, 3.
c
Press Stop/Exit.
Press a or b to choose the time zone.
Press OK.
c
Press Stop/Exit.
11
Send in the Product
Registration and Test
Sheet (USA only)
16
You can also register your product online using the
On-Line Registration link from the installation
CD-ROM or visit
a
Fill out the Product Registration and Test
Sheet.
b
Put the sheet face up in the ADF (Automatic
Document Feeder) or face down on the
scanner glass.
c
d
e
Make sure
(FAX) is illuminated in Blue.
Enter the toll-free fax number: 1-877-268-9575.
Press Black Start or Color Start.
Note
You will receive a confirmation fax of your Product
Registration.
12
Choose your connection type
17
®
®
®
These installation instructions are for Windows 2000 Professional, Windows XP Home/Windows XP
®
®
®
Professional, Windows XP Professional x64 Edition, Windows Vista , Windows 7, and Mac OSX (versions
10.4.11, 10.5.x and 10.6.x).
Note
®
For Windows Server 2003/2003 x64 Edition/2008/2008 R2, visit your model page at
For USB Interface Users
Macintosh, go to page 16
For Wired Network
Macintosh, go to page 21
Note
You can download the latest drivers and utilities for your machine from the Brother Solutions Center at
13
®
USB
Windows
For USB Interface Users
(Windows® 2000 Professional/XP/XP Professional x64 Edition/
Windows Vista®/Windows® 7)
Before you install
Install MFL-Pro Suite
18
19
Put the installation CD-ROM into your
CD-ROM drive. If the model name screen
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
a
appears, choose your machine. If the language
screen appears, choose your language.
IMPORTANT
• If there are any programs running, close
them.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
• The screens may differ depending on your
operating system.
Note
b
Click Initial Installation and then Install
MFL-Pro Suite.
The installation CD-ROM includes ScanSoft™
PaperPort™ 12SE. This software supports
Windows XP (SP3 or greater), XP Professional
x64 Edition (SP3 or greater), Windows Vista
(SP2 or greater) and Windows 7. Update to the
®
®
®
®
latest Windows Service Pack before installing
MFL-Pro Suite. For Windows 2000 (SP4 or
®
greater) users, when the ScanSoft™ PaperPort™
11SE download screen appears during the
installation of MFL-Pro Suite, follow the on-screen
instructions.
c
Click Yes if you accept the license agreements.
b
Turn off the machine and make sure the USB
interface cable is NOT connected to the
machine. If you have already connected the
cable, disconnect it.
Note
• If the installation does not continue
automatically, open the top menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
MFL-Pro Suite.
®
®
• For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
• If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
d
Follow the on-screen instructions until this
screen appears.
14
®
USB
Windows
e
f
Connect the USB cable to the USB connector
marked with the
symbol on your machine
and then connect the cable to your computer.
Turn the machine on, and follow the on-screen
instructions to complete setup.
IMPORTANT
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
®
®
• For Windows Vista and Windows 7 users,
when the Windows Security screen appears,
click the check box and click Install to complete
the installation correctly.
• If an error message appears during the
software installation, run the
Installation Diagnostics located in
start/All Programs/Brother/MFC-XXXX
(where MFC-XXXX is your model name).
The installation is now
complete.
Finish
Note
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
15
USB
Macintosh
For USB Interface Users
(Mac OS X 10.4.11 - 10.6.x)
Before you install
Install MFL-Pro Suite
18
19
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
a
b
Put the installation CD-ROM into your
CD-ROM drive.
Double-click the Start Here OSX icon. Follow
the on-screen instructions.
IMPORTANT
For Mac OS X 10.4.10 users, upgrade to
Mac OS X 10.4.11 - 10.6.x. (For the latest
drivers and information on the Mac OS X you
Note
If you want to setup the PS driver (BR-Script3
printer driver), please go to the Brother Solutions
Downloads on your model page and visit FAQ's
for setup instructions.
Note
It may take a few minutes for installation to
complete.
b
Connect the USB cable to the USB connector
marked with the symbol on your machine
and then connect the cable to your Macintosh.
c
Follow the on-screen instructions until this
screen appears. Choose your machine from
the list, and then click OK.
d
When this screen appears, click Next.
c
Make sure your machine's power switch is on.
The installation of MFL-Pro Suite is now
complete.
16
USB
Macintosh
Download and install
Presto! PageManager
20
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a
On the Brother Support screen, click
Presto! PageManager and follow the
on-screen instructions.
The installation is now
complete.
Finish
17
®
Wired Network
Windows
For Wired Network Interface Users
(Windows® 2000 Professional/XP/XP Professional x64 Edition/
Windows Vista®/Windows® 7)
c
Connect the network interface cable to the LAN
connector and then connect it to a free port on
your hub.
Before you install
18
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
IMPORTANT
• If there are any programs running, close
them.
d
Make sure your machine's power switch is on.
• The screens may differ depending on your
operating system.
Install MFL-Pro Suite
Note
• The installation CD-ROM includes ScanSoft™
PaperPort™ 12SE. This software supports
Windows XP (SP3 or greater), XP
Professional x64 Edition (SP3 or greater),
Windows Vista (SP2 or greater) and
Windows 7. Update to the latest Windows
Service Pack before installing MFL-Pro Suite.
For Windows 2000 (SP4 or greater) users,
when the ScanSoft™ PaperPort™ 11SE
download screen appears during the installation
of MFL-Pro Suite, follow the on-screen
instructions.
19
®
a
Put the installation CD-ROM into your
CD-ROM drive. If the model name screen
appears, choose your machine. If the language
screen appears, choose your language.
®
®
®
®
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
• Disable all personal firewall software (other
than Windows Firewall), anti-spyware or
antivirus applications for the duration of the
installation.
®
b
Click Initial Installation and then Install
MFL-Pro Suite.
b
Remove the protective cap from the LAN
connector marked with a symbol.
c
Click Yes if you accept the license agreements.
18
®
Wired Network
Windows
Note
Note
• If your machine is not found over the network,
confirm your settings by following the on-screen
instructions.
• If the installation does not continue
automatically, open the top menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
MFL-Pro Suite.
• You can find your machine’s IP address and the
node name by printing out the Network
Configuration List. See Print the Network
®
®
• For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
®
®
• For Windows Vista and Windows 7 users,
when the Windows Security screen appears,
click the check box and click Install to complete
the installation correctly.
• If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
• If an error message appears during the
software installation, run the
d
When the Firewall/AntiVirus detected screen
appears, choose Change the Firewall port
settings to enable network connection and
continue with the installation.
Installation Diagnostics located in
start/All Programs/Brother/MFC-XXXX LAN
(where MFC-XXXX is your model name).
(Recommended) and click Next.
®
(Not for Windows 2000 users)
Install MFL-Pro Suite on
additional computers
20
(if needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
Note
®
Network license (Windows )
®
If you are not using the Windows Firewall, see
This product includes a PC license for up to
5 users. This license supports the installation of
the MFL-Pro Suite including ScanSoft™
PaperPort™ 12SE or ScanSoft™ PaperPort™
11SE on up to 5 PCs on the network. If you want
to use more than 5 PCs with ScanSoft™
PaperPort™ 12SE or ScanSoft™ PaperPort™
11SE installed, please purchase the Brother NL-5
pack which is a multiple PC license agreement
pack for up to 5 additional users. To purchase the
NL-5 pack, contact your authorized Brother
dealer or contact Brother customer service.
the user’s guide for your software for
information on how to add the following
network ports.
For network scanning, add UDP port 54925.
For network PC-Fax receiving, add UDP port
54926.
If you still have trouble with your network
connection, add UDP port 137.
e
Follow the on-screen instructions to complete
setup.
IMPORTANT
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
The installation is now
complete.
Finish
19
®
Wired Network
Windows
Note
• If you use a specified IP Address for the
machine, you must set the Boot Method to
Static by using the control panel. For more
information, see Network menu in the Network
User's Guide.
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
20
Wired Network
Macintosh
For Wired Network Interface Users
(Mac OS X 10.4.11 - 10.6.x)
Before you install
Install MFL-Pro Suite
18
19
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
a
b
Put the installation CD-ROM into your
CD-ROM drive.
Double-click the Start Here OSX icon. Follow
the on-screen instructions.
IMPORTANT
For Mac OS X 10.4.10 users, upgrade to
Mac OS X 10.4.11 - 10.6.x. (For the latest
drivers and information on the Mac OS X you
Note
If you want to setup the PS driver (BR-Script3
printer driver), please go to the Brother Solutions
Downloads on your model page and visit FAQ's
for setup instructions.
Note
It may take a few minutes for installation to
complete.
b
Remove the protective cap from the LAN
connector marked with a symbol.
c
Follow the on-screen instructions until this
screen appears. Choose your machine from
the list, and then click OK.
c
d
Connect the network interface cable to the LAN
connector and then connect it to a free port on
your hub.
Note
If your machine is not found over the network,
confirm your network settings. See Before you
Make sure your machine's power switch is on.
21
Wired Network
Macintosh
Note
Download and install
Presto! PageManager
• You can find your machine’s MAC Address
(Ethernet Address) and IP Address by printing
out the Network Configuration List. See Print
20
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
• If this screen appears click OK.
a
On the Brother Support screen, click
Presto! PageManager and follow the
on-screen instructions.
Enter a name for your Macintosh in
Display Name up to 15 characters long and
Install MFL-Pro Suite on
additional computers
• If you want to use the machine’s SCAN key to
scan over the network, you must check the
Register your computer with the "Scan To"
function on the machine box.
21
(if needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
• The name you enter will appear on the
machine’s LCD when you press
(SCAN)
and choose a scan option. (For more
information, see Network Scanning in the
Software User's Guide.)
The installation is now
complete.
Finish
d
When this screen appears, click Next.
Note
If you use a specified IP Address for the machine,
you must set the Boot Method to Static by using
the control panel. For more information, see
Network menu in the Network User's Guide.
The installation of MFL-Pro Suite is now
complete.
22
For Network Users
Web Based Management
(web browser)
Print the Network Configuration
List
The Brother print server is equipped with a web server
that allows you to monitor its status or change some
of its configuration settings, using HTTP (Hyper Text
Transfer Protocol).
You can print the Network Configuration List to
confirm the current network settings.
a
Turn on the machine and wait until the machine
is in the Ready state.
Note
• The default User Name is ‘admin’ and the
default password is ‘access’. You can use a
web browser to change this password.
b
c
Press Menu, 6, 6.
Press Black Start or Color Start.
®
• We recommend Microsoft Internet
The machine will print the current network
settings.
®
Explorer 6.0 (or greater) or Firefox 3.0 (or
®
greater) for Windows and Safari 3.0 (or
greater) for Macintosh. Please also make sure
that JavaScript and cookies are always enabled
in whichever browser you use. To use a web
browser, you will need to know the IP address
of the print server. The IP address of the print
server is listed on the Network Configuration
List.
Restore the network settings to
factory default
To restore all network settings of the internal
Print/Scan server to factory default, please follow the
steps below.
a
b
Open your browser.
a
Make sure the machine is not operating, then
disconnect all the cables from the machine
(except the power cord).
your browser (where machine_ip_address
is the IP address of the printer or the print
server name).
b
c
d
Press Menu, 7, 0.
Press 1 to choose Reset.
Press 1 to choose Yes.
The machine will restart, re-connect cables
once this is complete.
See Web Based Management in the Network
User's Guide.
23
Other Information
Color Correction (if needed)
Color Calibration
The output density for each color may vary depending
on the environment the machine is in, such as
temperature and humidity. Calibration helps you to
improve the color density.
Color Registration
Auto Registration
You can adjust the print position of each color
automatically.
a
b
c
Press Menu, 4, 7.
Press 1 to choose Start.
Press Stop/Exit.
Note
• If you print using the Direct Print feature or the
BR-Script printer driver, you need to perform
the calibration from the control panel. See
To adjust the print position of each color
manually, see Manual Registration in the
Advanced User's Guide.
®
• If you print using the Windows printer driver,
the driver will get the calibration data
Brother CreativeCenter Icon
automatically if both Use Calibration Data and
Get Device Data Automatically are on. See
Advanced tab in the Software User's Guide.
• If you print using the Macintosh printer driver,
you need to perform the calibration using
Status Monitor. After turning Status Monitor
on, choose Color Calibration from Control
menu. See Status Monitor in the Software
User's Guide.
Get inspired. Double-click the Brother CreativeCenter
icon on your desktop to access a FREE web site with
many ideas and resources for personal and
professional use.
Using the control panel
a
b
Press Menu, 4, 6.
Press a or b to choose Calibrate.
Press OK.
c
d
Press 1 to choose Yes.
Press Stop/Exit.
You can reset the calibration parameters back to
those set at the factory.
a
b
Press Menu, 4, 6.
Press a or b to choose Reset.
Press OK.
c
d
Press 1 to choose Yes.
Press Stop/Exit.
24
Options and Consumables
Options
The machine has the following optional accessories. You can expand the capabilities of the machine by adding
these items. For more information about the optional Lower Tray Unit and compatible SO-DIMM Memory, visit us
For installing the SO-DIMM Memory, see Installing extra memory in the Advanced User's Guide.
Lower Tray Unit
SO-DIMM Memory
LT-300CL
You can increase the memory by installing one
SO-DIMM (Small Outline Dual In-line Memory
Module).
The lower paper tray unit can hold up to 500 sheets
of paper. When the tray is installed, the machine
expands total input capacity up to 800 sheets.
Consumables
When the time comes to replace consumable items, an error will be indicated by the LCD on the control panel. For
more information about the consumables for your machine, visit us at http://solutions.brother.com/ or contact your
local Brother reseller.
Toner cartridges
Drum unit
Standard Toner: TN-310 (C/M/Y/BK)
High Capacity Toner: TN-315 (C/M/Y/BK)
DR-310CL
Belt Unit
Waste Toner Box
BU-300CL
WT-300CL
25
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries.
Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates
in the United States and/or other countries.
Any trade names and product names of companies appearing on Brother products, related documents and any other
materials are all trademarks or registered trademarks of those respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2010 Brother Industries, Ltd.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC.
©2010 Devicescape Software, Inc.
This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC, Inc.
|