Operator’s Manual
Vanguard
Gasoline
Model 430447
433447
580447
583447
589447
ECopyright Briggs & Stratton Corporation
Form No. 277108-9/06
Printed in U.S.A.
BRIGGSandSTRATTON.com
Milwaukee, Wisconsin 53201 U.S.A.
SAFETY
WARNING
WARNING
Gasoline and its vapors are extremely
flammable and explosive.
Starting engine creates sparking.
Sparking can ignite nearby flammable
gases.
Fire or explosion can cause severe burns
or death.
Explosion and fire could result.
WHEN ADDING FUEL
• If there is natural or LP gas leakage in area, do not start
• Turn engine OFF and let engine cool at least 2 minutes
engine.
before removing gas cap.
• Do not use pressurized starting fluids because vapors are
• Fill fuel tank outdoors or in well-ventilated area.
flammable.
• Do not overfill fuel tank. Fill tank to approximately 1-1/2
inches below top of neck to allow for fuel expansion.
• Keep gasoline away from sparks, open flames, pilot lights,
heat, and other ignition sources.
WARNING
• Check fuel lines, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
Running engines produce heat. Engine
parts, especially muffler, become ex-
tremely hot.
WHEN STARTING ENGINE
• Make sure spark plug, muffler, fuel cap and air cleaner are in
Severe thermal burns can occur on
contact.
place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting engine.
Combustible debris, such as leaves,
grass, brush, etc. can catch fire.
• If engine floods, set choke to OPEN/RUN position, place
throttle in FAST and crank until engine starts.
• Allow muffler, engine cylinder and fins to cool before
WHEN OPERATING EQUIPMENT
touching.
• Do not tip engine or equipment at angle which causes
• Remove accumulated combustibles from muffler area and
gasoline to spill.
cylinder area.
• Do not choke carburetor to stop engine.
• Install and maintain in working order a spark arrester before
using equipment on forest-covered, grass-covered,
brush-covered unimproved land. The state of California
requires this (Section 4442 of the California Public
Resources Code). Other states may have similar laws.
Federal laws apply on federal land.
WHEN TRANSPORTING EQUIPMENT
• Transport with fuel tank EMPTY or with fuel shut-off valve
OFF.
WHEN STORING GASOLINE OR EQUIPMENT
WITH FUEL IN TANK
• Store away from furnaces, stoves, water heaters or other
appliances that have pilot light or other ignition source
because they can ignite gasoline vapors.
WARNING
Rotating parts can contact or entangle
hands, feet, hair, clothing, or accessories.
Traumatic amputation or severe lacera-
tion can result.
WARNING
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
Engines give off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
• Do not wear loose-fitting clothing, dangling drawstrings or
items that could become caught.
• Start and run engine outdoors.
• Do not start or run engine in enclosed area, even if doors or
windows are open.
3
SAFETY
WARNING
WARNING
Unintentional sparking can result in
fire or electric shock.
If engine is warm DO NOT remove radiator
cap.
Escaping steam can cause burns.
Unintentional start-up can result in
entanglement, traumatic amputation,
or laceration.
• Do not touch hot radiator, or open reservoir when engine is
running
• Allow engine to cool before removing radiator cap, changing,
or adding coolant.
BEFORE PERFORMING ADJUSTMENTS OR
REPAIRS
WARNING
• Disconnect spark plug wire and keep it away from spark
plug.
• Disconnect battery at negative terminal.
Never remove radiator cap or radiator
reservoir cap while the engine is hot or
running. Severe thermal burns or injury
can occur by escaping steam or hot
engine coolant.
WHEN TESTING FOR SPARK
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
• Stop engine and allow to cool before removing radiator or
reservoir cap.
WARNING
• To remove reservoir cap after engine is cool, place a thick
cloth over cap and remove it slowly.
Briggs & Stratton does not approve or authorize the use of
these engines on 3-wheel All Terrain Vehicles (ATVs), motor
bikes, fun/recreational go-karts, aircraft products or vehicles
intended for use in competitive events. Use of these engines in
such applications could result in property damage, serious
injury (including paralysis), or even death.
• To remove radiator cap after engine is cool, place a thick
cloth over cap and rotate it slowly counter-clockwise to the
first stop. Pressurized steam may emit from the cap, stand
back to avoid injury. Once all pressure is released, rotate cap
counter-clockwise while pushing down on cap to remove.
ENGINE INFORMATION
TECHNICAL INFORMATION
GENERAL INFORMATION
ENGINE MODEL
Engine Power Rating Information
The gross power rating for individual gas engine models is labeled
in accordance with SAE (Society of Automotive Engineers) code
J1940 (Small Engine Power & Torque Rating Procedure), and
rating performance has been obtained and corrected in
This is a three cylinder, water cooled engine.
MODEL 430447, 433447
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 mm (2.68 in.)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 mm (2.52 in.)
Displacement . . . . . . . . . . . . . . . . . . . . . . 697 cc (42.5 cu. in.)
MODEL 580447, 583447, 589447
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 mm (2.834 in.)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 mm (3.07 in.)
Displacement . . . . . . . . . . . . . . . . . . . . . . 953 cc (58.1 cu. in.)
accordance with SAE J1995 (Revision 2002-05). Actual gross
engine power will be lower and is affected by, among other things,
ambient operating conditions and engine-to-engine variability.
Given both the wide array of products on which engines are
placed and the variety of environmental issues applicable to
operating the equipment, the gas engine will not develop the rated
gross power when used in a given piece of power equipment
(actual “on-site” or net horsepower). This difference is due to a
variety of factors including, but not limited to, accessories (air
cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.),
application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to-engine variability. Due to
manufacturing and capacity limitations, Briggs & Stratton may
substitute an engine of higher rated power for this Series engine.
TUNE-UP SPECIFICATIONS
Spark plug gap . . . . . . . . . . . . . . . . . . . . . 0.76 mm (0.030 in.)
Valve clearance (check when engine is cold).
Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.18 mm (0.007 in.)
Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.18 mm (0.007 in.)
4
ENGINE INFORMATION
ENGINE PARTS
2
1
3
7
16
15
14
4
13
5
8
9
12
6
11
10
10
1. Thermostat
2. Oil filler cap
3. Ignition coil
10. Oil drains
11. Oil filter
12. Dipstick
4. Electric starter
5. Oil pan
13. Oil pressure sending unit
14. Carburetor
6. Alternator
7. Spark plug
15. Engine Date Code
xxxxxxxxx
8. Coolant temperature sending unit
9. Governor lever
16. Engine Model & Type number
xxxxxx xxxx-xx
5
OIL
OIL CAPACITY
Oil capacity, including oil filter, is 3.5 quarts or 3.3 liters.
TYPE OF OIL TO USE
SAE Viscosity Grades
• Use high quality detergent oil classified “For Service SH, SJ” or
higher.
• Do not use special additives with recommended oils.
• Do not mix oil with gasoline.
• Choose a viscosity according to the table opposite.
*
CAUTION: This engine is shipped from Briggs &
Stratton without oil. Check oil level before starting
engine. If you start the engine without oil, the engine
will be damaged beyond repair and will not be
covered under warranty.
10
32
0
50
70
21
90
32
110
43
-30
-34
-10
-23
°F
°C
-12
10
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
*
A synthetic 5W-30 oil may be used.
CHECKING AND ADDING OIL
• Check oil level before starting the engine.
• Check level daily, or after every eight (8) hours.
• Keep oil level at FULL.
Note: After filling with or changing oil, start and run engine at
idle for 5 minutes. Shut engine off. Wait 3 minutes and check oil
level. Add oil, if required, to bring level to Full mark on dipstick.
• Do not overfill.
OIL FILL
Bring oil
level to F
mark
on dipstick.
[2]. Remove dipstick and wipe
with clean cloth.
[4]. If oil is required, remove dipstick to allow
proper venting and pour oil slowly. Fill to
FULL line on dipstick. Recheck.
[3]. Then replace dipstick, and
remove to check oil level.
[1]. Place equipment level.
Clean around oil fill.
CAUTION: When filling engine or adding oil.
To prevent engine damage upon
start-up, proper venting is necessary
when filling engine with oil or adding oil.
Note
Clearance
In addition to ensuring a level engine,
removing dipstick, and pouring oil
slowly, there must be clearance
between the oil fill device and the oil fill
hole in the valve cover as shown. This
clearance is necessary to permit
venting when filling, which prevents oil
from overrunning into breather.
Note
Clearance
[5]. Replace dipstick firmly.
6
FUEL
TYPE OF FUEL TO USE
WARNING
• Use clean, fresh, unleaded gasoline with a minimum of 85 octane.
Fresh fuel prevents gum from forming in the fuel system or on
essential carburetor parts. Purchase fuel in quantity that can be
used within 30 days. In countries other than U.S.A., leaded
gasoline may be used if it is commercially available and unleaded
is unavailable.
• Do not use gasoline which contains Methanol.
• Do not mix oil with gasoline.
• Fill fuel tank outdoors or in well-ventilated area, away
from sparks, open flames, pilot lights, heat, and other
ignition sources.
• If fuel spills, wait until it evaporates before starting
• THIS ENGINE IS CERTIFIED TO OPERATE ON GASOLINE.
engine.
• Turn engine OFF and let engine cool at least 2 minutes
before removing gas cap.
ADDING FUEL
[1]. Remove cap. Fill tank to approximately 1-1/2 inches
below top of neck to allow for fuel expansion. Be careful
not to overfill.
[2]. Replace cap before starting.
[3]. Check for fuel leaks at fuel filter, carburetor, fuel pump,
fuel pipe, etc.
COOLANT
SPECIFICATIONS
• This engine is water cooled.
• Do not touch radiator or open
WARNING
radiator cap, or open reservoir
when engine is hot or running.
• A 50/50% mixture is required of phosphate-free antifreeze and
tap water for heat dissipation, rust resistance and lubrication.
• Allow engine to cool before
changing or adding coolant.
CHANGING & ADDING COOLANT
• Fill radiator to bottom of fill cap seat and between FULL and LOW
in reservoir, if so equipped.
GAUGES
TYPICAL GAUGES (If Equipped)
COOLANT TEMPERATURE GAUGE
FUEL GAUGE
Indicates coolant temperature
when the starter switch is ON.
Normal range 80° − 90° C
(175° − 195° F).
To minimize condensation,
keep fuel tank full.
Dangerous range above 105° C
(220° F).
HOUR METER
FUEL SHUT-OFF
Indicates the total number of
hours the engine has been run.
Open valve before starting
engine.
ON
POSITION
CAUTION: To prevent leaking, close fuel shut-
off valve when engine is transported.
7
GAUGES
TYPICAL PANEL LIGHTS (If Equipped)
WARNING LIGHTS (Typical)
Ignition light
The ignition light comes on when the starter switch is turned to
the ON position, and should be out while engine is running. If
ignition light goes out when starter switch is turned to the ON
position, check fuse or bulb.
Engine oil pressure light
Temperature light
The engine oil pressure light comes on when the starter
switch is turned to the ON position and should be out while
engine is running. If oil pressure light comes on while engine is
running, stop engine immediately. Check oil level or electrical
system.
If temperature light comes on, engine is overheating. Check:
S
coolant level;
debris on radiator or any restriction to air flow.
S
Charge light
See an Authorized Briggs & Stratton 3/LC Service Dealer if
necessary for operation repair.
The charge light comes on when the starter switch is turned to
the ON position, but should be out while engine is running. If
charge light comes on while engine is running, check electrical
system.
STARTING
STARTING IN COLD WEATHER:
♦Use correct type of oil for expected starting
♦After engine has started, release key, which will return
temperature. (See Oil.)
to ON position.
♦Remove external equipment/engine loads. (See
♦Allow engine to warm up several seconds to several
equipment operating instructions.)
minutes, depending on outside temperature.
♦Periodically remove any debris buildup from the
♦Gradually open choke.
machine (See Maintenance.)
♦Use fresh gasoline, which has higher volatility to
♦Open fuel shut-off valve, if equipped, before starting
improve starting.
engine.
♦For maximum performance and life, operate engine
♦Pull choke and move throttle to FAST position.
with choke in OPEN and throttle in FAST.
CAUTION: Before starting engine for
the first time, charge battery as the
equipment manufacturer recommends.
Failure to do so, may cause damage to
the engine.
WARNING
• The manufacturer of equipment on which
this engine is installed specifies top speed at
which engine will be operated. DO NOT
EXCEED this speed.
WARNING
• Do not use pressurized starting fluids.
• Vapors are flammable.
• Keep hands and feet clear of rotating
machinery.
8
STARTING & STOPPING
TO START ENGINE
Typical starter switch
Typical throttle control
[2]. Open throttle control
slightly.
[1]. Insert key into starter
switch at OFF position.
[3]. Turn key to START.
CAUTION: To prolong starter life, use short starting cycles, not to
exceed 15 secs/min. Extended cranking can damage starter motor.
Follow equipment manufacturer’s recommendations, if any.
[5]. NOTE: If engine does not start
immediately follow below:
PULL
TO CHOKE
CHOKE OPERATION/ENGINE WARM-UP
• If engine does not start immedi-
ately, pull choke.
Typical starter switch
• After starting, allow engine to
warm up a few minutes before
[4]. When engine starts, release key,
which will return to ON position.
applying load. Open choke grad-
ually when applying load.
Typical choke control
TO STOP ENGINE
CAUTION:
Do not move choke control
to CHOKE to stop engine.
Backfire or engine damage
may occur.
[2]. Turn key to
OFF.
Always remove
key and store
out of reach of
children.
Typical throttle control
[1]. Move throttle to SLOW.
Allow engine to run for
short time to cool down.
Typical starter switch
9
MAINTENANCE
REGULAR MAINTENANCE WILL IMPROVE THE PERFORMANCE AND EXTEND THE LIFE OF THE ENGINE.
MORE FREQUENT SERVICE IS REQUIRED WHEN OPERATING IN ADVERSE CONDITIONS.
See an Authorized Briggs & Stratton 3/LC Dealer for service. Use only genuine Briggs & Stratton Parts. Other parts may not
perform as well, may damage the engine, and may result in injury. In addition, use of other parts may void your warranty.
DAILY CHECKS
Task
Perform task at
hourly or calendar
interval.
OIL
Before starting engine, check oil for correct level.
See page 6 of this manual for instructions on checking
and adding oil.
Check oil level
4
CAUTION: Used oil is a hazardous waste prod-
uct. Dispose of used oil properly. Do not discard with
household waste. Check with your local authorities,
service center, or dealer for safe disposal/recycling
facilities.
Check for
oil leaks
4
Change oil and
oil filter
4*
Check coolant
Change coolant
Check fan belt
4
CLEANING DEBRIS
4
Daily or before every use, clean accumulated debris from
engine. Keep linkage, springs and controls clean.
4
Service
air cleaner
4*
4**
Engine parts should be kept
WARNING
clean to reduce the risk of
overheating and ignition of
accumulated debris.
Check valve
clearance
4
Check battery
electrolyte
4
CAUTION: Do not use water to clean engine
parts. Water could contaminate fuel system. Use a
brush or dry cloth.
Change
spark plugs
4
Change fuel filter
4
Clean
spark arrestor
(if equipped)
4
MUFFLER
Before running engine, clean
muffler and manifold areas to
remove all grass and com-
bustible debris.
Depending on use, this may
need to be performed more
often.
WARNING
*
Perform first maintenance operation after 50
hours. All subsequent maintenance performed at this
interval, unless specified. Service more often when
operating under heavy load or in high temperatures.
** Replace after every 600 hours of operation. Service
more often when operating under heavy load or in high
temperatures.
10
MAINTENANCE
DAILY CHECKS continued
COOLANT
WARNING
Never remove radiator cap or radiator reservoir
cap while the engine is hot or running. Severe
thermal burns or injury can occur by escaping
steam or hot engine coolant.
Coolant level should be between FULL and LOW when
engine is cold. If reservoir is dry, it must be filled along with
radiator .
Check coolant level when engine is cold.
If engine is warm DO NOT remove radiator cap.
Normal water temperature
gauge should read between
175° and 195° F (80° and 90° C)
when engine is running.
• Stop engine and allow to cool before removing radiator or
WARNING
reservoir cap.
• To remove reservoir cap after engine is cool, place a thick
cloth over cap and remove it slowly.
If water temperature rises
above 220° F (105° C), idle
engine down for a while. Then stop engine. Once engine
is cooled, check coolant level, fan belt tension and
clogged radiator fins.
• To remove radiator cap after engine is cool, place a thick
cloth over cap and rotate it slowly counter-clockwise to
the first stop. Pressurized steam may emit from the cap,
stand back to avoid injury. Once all pressure is released,
rotate cap counter-clockwise while pushing down on cap
to remove.
REGULAR MAINTENANCE
CHANGING OIL
WARNING
[1]. Place engine level.
[2]. Disconnect battery at negative terminal, and discon-
nect spark plug wires.
[3]. With engine OFF but still warm remove oil drain plug
and drain oil into appropriate receptacle.
• Disconnect spark plug wires and keep it away from spark
plugs.
• Disconnect battery at negative terminal.
[4]. Reinstall drain plug and torque to 352 kg-cm
(25.5 ft-lb).
[5]. Refill engine with new oil. Fill to FULL mark on
dipstick with new oil. Replace oil cap.
Caution: Do not overfill.
[6]. Start and run engine at idle for 5 minutes.
[7]. Stop engine, and wait 3 minutes. Then re-check oil
level.
OIL FILTER
[8]. If required, add oil to bring level to F mark on dipstick.
OIL DRAIN
[9]. Check for leaks.
OIL DRAIN
11
MAINTENANCE
REGULAR MAINTENANCE continued
CHANGING OIL FILTER
[1]. Perform this maintenance during oil change main-
tenance. Drain engine oil as described for oil
change, and remove oil filter.
[2]. Before installing new filter, apply to filter gasket
fresh, clean oil.
[3]. Screw filter on by hand until gasket contacts oil
filter adapter. Tighten 1/2 to 3/4 turn more.
OIL FILTER
[4]. Add fresh oil. Follow steps as described for oil
change.
OIL DRAIN
OIL DRAIN
[5]. Check for oil leaks around filter.
AIR CLEANER
Note: Air cleaner may be supplied by equipment manufacturer.
Cartridge
To clean cartridge, gently tap on end with handle of
screwdriver. Replace cartridge if very dirty or damaged.
AIR
CLEANER
BODY
CAUTION: Do not use pressurized air or solvents
to clean cartridge. Pressurized air can damage
cartridge; solvents will dissolve cartridge.
CARTRIDGE
COVER
[1]. Unlock clamps and remove cover.
[2]. Remove cartridge from air cleaner body.
[3]. Carefully clean out air cleaner cover.
[4]. Install cartridge in body.
CLAMPS
[5]. Install cover and lock clamps.
SPARK PLUG
♦Check and re-gap spark plugs if required.
♦Replace if damaged.
♦Use an approved spark tester to check for spark.
0.76 mm (0.030”)
WIRE GAGE
Note: In some areas,
local law requires using
resistor spark plug to
suppress ignition sig-
nals. If this engine was
originally equipped with
resistor spark plug, use
same
type
for
replacement.
12
MAINTENANCE
VALVE CLEARANCE
With No. 1 piston at TDC of compression stroke, check valve
clearances for cylinders shown in chart below. Rotate crank-
shaft 360° clockwise to check remaining valves. Adjust in
same order, if required.
Note: If engine is running normally, this check and adjustment
may be omitted.
Piston Position
Cylinder
Int
1
D
D
2
3
D
No. 1 piston at TDC, of compres-
sion stroke
Exh
Int
D
D
Rotate Crankshaft 360° clockwise
Exh
D
[1]. Loosen adjusting lock nut.
[2]. Using a wrench to hold adjusting lock nut, adjust with
screwdriver. Determine clearance using a feeler gauge.
[3]. While holding screw driver in place, torque adjusting
lock nut.
Valve clearances (cold):
SCREW
DRIVER
WRENCH
Int
Exh
0.18 mm (0.007 in.)
0.18 mm (0.007 in.)
FEELER
GAUGE
Adjusting lock nut torque: 110 kg-cm (95 in-lbs.)
Check valve cover gasket for leakage. Replace if required.
Torque valve cover nuts to 55 kg-cm (48 in-lbs.)
FUEL FILTER
WARNING
[1]. Disconnect spark plug wires and keep away from
spark plugs.
DIRECTION OF FUEL FLOW
[2]. When replacing fuel
filter, ensure clamps
are tight and fuel
flows as shown.
FUEL TANK
SIDE
Drain fuel tank or close fuel shut-off valve
before replacing fuel filter. Otherwise, fuel can
leak out, creating a fire/explosion hazard.
CARBURETOR
SIDE
FAN BELT
♦Check condition of fan belt.
♦Replace if damaged or worn.
BELT
To check for correct fan belt tension
When 10 kg (22 lbs.) of force is pressed at center of span
between fan and alternator, there should be 10 to 12 mm
(3/8 − 1/2 in.) of belt movement.
13
MAINTENANCE
To adjust for correct tension
HANDLE
[1]. Loosen the 2 bolts ( A and B ).
BELT
[2]. Place a handle (or similar object) between the
alternator and engine cylinder block. Then move the
alternator towards the outside of the engine, until the
fan belt deflection conforms to the specified value.
Specified fan belt deflection:
A
10 to 12mm / 10kg (3/8 to 1/2 in. / 22lbs.)
[3]. Temporarily tighten the 2 bolts ( A and B ) to fix the
alternator. Then remove the handle. Check fan belt
deflection. If it is within specifications, permanently
B
tighten the 2 bolts ( A and B ) as given below. If not,
repeat the above adjustment procedure.
Specified tightening torque:
A : 195 kg-cm (170 in-lbs)
B : 622 kg-cm (45 ft-lbs)
Check the fan belt deflection again.
ADJUSTMENTS
CONTROL ADJUSTMENTS
WARNING
If engine is hard to start or acceleration is uneven, check
control operation and adjust if required as described
below:
[1]. Move throttle control to FAST position.
[2]. Pull choke control to CHOKE position.
BEFORE PERFORMING ADJUSTMENTS OR
REPAIRS
• Disconnect spark plug wire and keep it away from spark
PULL
TO CHOKE
plug.
• Disconnect battery at negative terminal.
THROTTLE
WIRE AND
LEVER
CASING
Typical throttle and choke controls
[3]. Loosen casing clamp screw, then move wire and casing
and engine choke lever in direction of arrow, until choke
valve is completely closed.
And/Or
[4]. Move wire and casing and engine throttle lever in
direction of arrow, until it touches high speed screw.
CASING
CLAMP
HIGH SPEED
SCREW
SCREW
[5]. Tighten casing clamp screw.
CHOKE LEVER
Choke and throttle control adjustment
14
ADJUSTMENTS
CARBURETOR ADJUSTMENTS
Differences in fuel, temperature, altitude or load may require
minor carburetor adjustment. Air cleaner and air cleaner cover
must be assembled to carburetor before starting engine.
CARBURETOR
THROTTLE
LEVER
IDLE
MIXTURE
VALVE
The carburetor on this engine is low emission. It is equipped
with an idle mixture valve with a limiter (see inset), which allows
some adjustment, and an idle speed adjustment screw.
WITH LIMITER
Before adjustment, start and warm up engine approxi-
mately 5 minutes.
[1]. Place throttle control in IDLE or SLOW position.
FUEL
DRAIN
PLUG
IDLE SPEED
SCREW
[2]. Rotate carburetor throttle lever against idle speed screw
and hold.
[3]. Adjust idle speed screw to obtain equipment manufac-
turer’s specified idling speed.
Note: Engines operated at approx. 900 to 1500 m. (3000 to
5000 ft.) or above sea level may require a high altitude carbure-
tor main jet. If erratic performance is observed, contact an Au-
thorized Briggs & Stratton 3/LC Service Dealer for a high alti-
tude carburetor main jet.
[4]. Turn idle mixture valve with limiter midway between
limits.
15
SERVICE
PARTIAL LIST OF GENUINE BRIGGS & STRATTON PARTS
Part
Part No.
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100028
Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491056
Oil filter (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 820314
Air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 820263
Resistor spark plug
You may locate your nearest Authorized Briggs & Stratton
3/LC Service Dealer by calling 1-800-233-3723.
430447, 433447 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491055
580447, 583447, 589447 . . . . . . . . . . . . . . . . . . . . 496018
Spark tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19400
Fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 821026
Gas additive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5041
The illustrated shop manual shown here
includes common specifications and
detailed information covering adjust-
ment, tune-up and repair of B&S three
cylinder, 4 cycle engines. It is available
from an Authorized Briggs & Stratton
Service Dealer.
SERVICE
See an Authorized Briggs & Stratton 3/LC Service Dealer.
Each one carries a stock of Genuine Briggs & Stratton 3/LC
Parts and is equipped with special service tools. Only dealers
advertising as Authorized Briggs & Stratton 3/LC Service
Dealers are required to meet Briggs & Stratton standards.
Part No. MS-0750
When you purchase equip-
ment powered by a Briggs &
Stratton engine, you are assu-
red of highly skilled, reliable
service at any Authorized
Service Dealers worldwide.
Look for these signs wherev-
er Briggs & Stratton service is
offered.
STORAGE
Engines stored over 30 days need special attention.
[1]. To prevent gum from forming in fuel system or on
essential carburetor parts:
[2]. While engine is still warm, change oil.
[3]. Remove spark plugs and pour about 30 ml (1 oz.) of
engine oil into each cylinder. Replace spark plugs and
crank slowly to distribute oil.
a) if fuel tank contains oxygenated or reformulated
gasoline (gasoline blended with an alcohol or an ether),
run engine until it stops from lack of fuel, or b) if fuel tank
contains gasoline, either run engine until it stops from lack
of fuel, or add a gasoline additive to the gas in the tank.
(See parts list. Single-use pouches of gas additive are
available from your service dealer.) If you use a gas
additive, run the engine for several minutes to circulate the
additive through the carburetor. Then, engine and fuel can
be stored up to 24 months.
[4]. Clean engine of surface debris, chaff or grass.
[5].
Store in a clean, dry area. Do
not store in same area as a
stove, furnace, water heater, or
other appliance that uses a pilot
light or has a device that can
create a spark.
WARNING
16
For Model Series 430447, 433447, 580447 & 583447
which are less than 19 Kw
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emissions Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
EMISSIONS CONTROL WARRANTY COVERAGE IS APPLICABLE TO
CERTIFIED MODEL YEAR 2002 AND LATER ENGINES, WHICH ARE PUR-
CHASED AND USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR
2002 AND LATER ENGINES, WHICH ARE PURCHASED AND USED ELSE-
WHERE IN THE UNITED STATES.
California and United States Emissions Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and B&S are pleased
to explain the Emissions Control System Warranty on your model year 2002
and later small off-road engine (SORE). In California, new small off-road engi-
nes must be designed, built and equipped to meet the State’s stringent anti-
smog standards. Elsewhere in the United States, new small off-road engines
certified for model year 2002 and later, must meet similar standards set forth by
the U.S. EPA. B&S must warrant the emissions control system on your engine
for the period of time listed below, provided there has been no abuse, neglect or
improper maintenance of your small off-road engine.
Your emissions control system includes parts such as the carburetor, air
cleaner, ignition system, muffler and catalytic converter. Also included may
be connectors and other emissions related assemblies.
Where a warrantable condition exists, B&S will repair your small off-road en-
gine at no cost to you including diagnosis, parts and labor.
Briggs & Stratton Corporation Emissions Control Defects Warranty Coverage
Small off-road engines are warranted relative to emissions control parts de-
fects for a period of two years, subject to provisions set forth below. If any
covered part on your engine is defective, the part will be repaired or replaced
by B&S.
Owner’s Warranty Responsibilities
As the small off-road engine owner, you are responsible for the performance
of the required maintenance listed in your Operating & Maintenance Instruc-
tions. B&S recommends that you retain all your receipts covering mainte-
nance on your small off-road engine, but B&S cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all
scheduled maintenance.
As the small off-road engine owner, you should however be aware that B&S
may deny your warranty coverage if your small off-road engine or a part has
failed due to abuse, neglect, improper maintenance or unapproved modifi-
cations.
You are responsible for presenting your small off-road engine to an Autho-
rized B&S Service Dealer as soon as a problem exists. The undisputed
warranty repairs should be completed in a reasonable amount of time, not to
exceed 30 days.
If you have any questions regarding your warranty rights and responsibili-
ties, you should contact a B&S Service Representative at 1-800-233-3723.
EPA EMISSIONS COMPLIANCE PERIOD: 1000 Hours
CARB EMISSIONS COMPLIANCE PERIOD: 500 Hours
Briggs & Stratton Corporation Emissions Control Defects Warranty Provisions
The following are specific provisions relative to your Emissions Control Defects
Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated
engines found in the Operating & Maintenance Instructions.
2. Length of Coverage
B&S warrants to the initial owner and each subsequent purchaser that
the Warranted Parts shall be free from defects in materials and workman-
ship which caused the failure of the Warranted Parts for a period of two
years from the date the engine is delivered to a retail purchaser.
1. Warranted Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present
on the engine purchased.
3. No Charge
Repair or replacement of any Warranted Part will be performed at no
charge to the owner, including diagnostic labor which leads to the deter-
mination that a Warranted Part is defective, if the diagnostic work is per-
formed at an Authorized B&S Service Dealer. For emissions warranty
service, contact your nearest Authorized B&S Service Dealer as listed in
the “Yellow Pages” under “Lawn Mowers,” “Engines, Gasoline,” “Gaso-
line Engines” or similar category.
a. Fuel Metering System
•
•
•
•
Carburetor and internal parts
Cold start enrichment system
Fuel Pump
4. Claims and Coverage Exclusions
Fuel Filter
Warranty claims shall be filed in accordance with the provisions of the
B&S Engine Warranty Policy. Warranty coverage shall be excluded for
failures of Warranted Parts which are not original B&S parts or because
of abuse, neglect or improper maintenance as set forth in the B&S En-
gine Warranty Policy. B&S is not liable to cover failures of Warranted
Parts caused by the use of add-on, non-original, or modified parts.
b. Air Induction System
•
•
Air cleaner
Intake manifold
c. Ignition System
5. Maintenance
•
•
•
Spark plug
Ignition coil
Ignition processor
Any Warranted Part which is not scheduled for replacement as required
maintenance or which is scheduled only for regular inspection to the ef-
fect of “repair or replace as necessary” shall be warranted as to defects
for the warranty period. Any Warranted Part which is scheduled for
replacement as required maintenance shall be warranted as to defects
only for the period of time up to the first scheduled replacement for that
part. Any replacement part that is equivalent in performance and durabili-
ty may be used in the performance of any maintenance or repairs. The
owner is responsible for the performance of all required maintenance, as
defined in the B&S Operating & Maintenance Instructions.
d. Exhaust System
Exhaust manifold
e. Miscellaneous Items Used in Above Systems
•
•
Vacuum, temperature, position, time sensitive valves and
switches
•
•
•
Electronic Controls
Connectors and assemblies
Hoses
6. Consequential Coverage
Coverage hereunder shall extend to the failure of any engine compo-
nents caused by the failure of any Warranted Part still under warranty.
17
For Model Series 580447, 583447 & 589447
Which are equal to or more than 19 kW
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emissions Control System Warranty Statement
(Owner’s Warranty Rights and Obligations)
EMISSIONS CONTROL WARRANTY COVERAGE IS APPLICABLE TO
CERTIFIED MODEL YEAR 2004 AND LATER ENGINES, WHICH ARE
PURCHASED AND USED IN CALIFORNIA, AND TO CERTIFIED MODEL
YEAR 2004 AND LATER ENGINES, WHICH ARE PURCHASED AND
USED ELSEWHERE IN THE UNITED STATES.
California and United States Emissions Control Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and B&S are pleased
of time listed below, provided there has been no abuse, neglect or improper
to explain the Emissions Control System Warranty on your model year 2004
and later off-road spark-ignition engine over 19kW (25HP). In California, new
off-road large spark-ignition engines must be designed, built and equipped to
meet the State’s stringent anti-smog standards. Elsewhere in the United
States, new Non-road spark-ignition engines over 19kW certified for model
year 2004 and later, must meet similar standards set forth by the U.S. EPA.
B&S must warrant the emissions control system on your engine for the period
maintenance of your engine.
Your emissions control system includes parts such as the carburetor, air
cleaner, ignition system, muffler, and catalytic converter. Also included may
be hoses, belts, connectors and other emissions related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost
to you including diagnosis, parts and labor.
Briggs & Stratton Corporation Emissions Control Warranty Coverage
The 2004 and later off-road spark-ignition engines are warranted for two
years.
If any emissions-related part on your engine is defective, the part will be
repaired or replaced by B&S.
Owner’s Warranty Responsibilities
As the engine owner, you are responsible for the performance of the required
maintenance listed in your Operating & Maintenance Instructions. B&S
recommends that you retain all your receipts covering maintenance on your
engine, but B&S cannot deny warranty solely for the lack of receipts or for
your failure to ensure the performance of all scheduled maintenance.
As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect,
improper maintenance or unapproved modifications. You are responsible for
presenting your engine to an Authorized B&S Service Dealer as soon as a
problem exists. The warranty repairs should be completed in a reasonable
amount of time, not to exceed 30 days. If you have questions regarding your
warranty rights and responsibilities, you should contact a B&S Service
Representative at 1-800-233-3723.
EMISSIONS COMPLIANCE PERIOD:
1000 HOURS
Briggs & Stratton Corporation Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control
3. No Charge
Warranty Coverage. It is in addition to the B&S engine warranty for
non-regulated engines found in the Operating & Maintenance Instructions.
Repair or replacement of any Warranted Part will be performed at no
charge to the owner, including diagnostic labor which leads to the
determination that a Warranted Part is defective, if the diagnostic work
is performed at an Authorized B&S Service Dealer. For emissions
warranty service, contact your nearest Authorized B&S Service Dealer
as listed in the “Yellow Pages” under “Engines, Gasoline,” “Gasoline
Engines,” “Lawn Mowers,” or similar category.
1. Warranted Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present
on the engine purchased.
a. Fuel Metering System
Carburetor and internal parts
Cold start enrichment system
Fuel pump
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the
B&S Engine Warranty Policy. Warranty coverage shall be excluded for
failures of Warranted Parts which are not original B&S parts or because
of abuse, neglect or improper maintenance as set forth in the B&S
Engine Warranty Policy. B&S is not liable to cover failures of Warranted
Parts caused by the use of add-on, non-original, or modified parts.
Fuel filter
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug
5. Maintenance
Ignition coil
Any Warranted Part which is not scheduled for replacement as required
maintenance or which is scheduled only for regular inspection to the
effect of “repair or replace as necessary” shall be warranted as to
defects for the warranty period. Any Warranted Part which is scheduled
for replacement as required maintenance shall be warranted as to
defects only for the period of time up to the first scheduled replacement
for that part. Any replacement part that is equivalent in performance and
durability may be used in the performance of any maintenance or
repairs. The owner is responsible for the performance of all required
maintenance, as defined in the B&S Operating & Maintenance
Instructions.
Ignition processor
d. Exhaust System
Exhaust manifold
e. Miscellaneous Items Used in Above System
Vacuum, temperature, position, time sensitive valves and switches
Electronic controls
Connectors and assemblies
Hoses
2. Length of Coverage
B&S warrants to the initial owner and each subsequent purchaser that
the Warranted Parts shall be free from defects in materials and
workmanship which caused the failure of the Warranted Parts for a
period of two years from the date the engine is delivered to a retail
purchaser.
6. Consequential Coverage
Coverage hereunder shall extend to the failure of any engine
components caused by the failure of any Warranted Part still under
warranty.
18
BRIGGS & STRATTON 3/LC ENGINE OWNER WARRANTY POLICY
Effective January 1, 2006 replaces all undated Warranties and all Warranties dated before January 1, 2006
LIMITED WARRANTY
Briggs & Stratton Corporation (B&S) will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the
time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Briggs & Stratton 3/LC Service Dealer in
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION
IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives
you specific legal rights and you may also have other rights which vary from state to state and country to country.
OUR PRODUCT
VANGUARDE
Major Parts Warranty*
Parts & Labor*
3/LC Engine
WARRANTY PERIOD
3 years
2 years
2 years
Consumer and Commercial Use
*
Note the following special warranty periods: For purposes of this warranty policy, Parts and Labor coverage is 2 years. Major parts only
coverage is extended to through the third year of operation. Major Parts Warranty (M.P.W.) covers but is not limited to or exclusive to cylinder
block, cylinder head, crankshaft, camshaft, gears, pistons, rods, flywheel, flywheel housing, oil pump, fan, pulleys, mechanical governor,
intake manifold, oil pan. M.P.W. does not cover and is not limited to piston rings, replaceable bearings, water pump, any electrical component,
valve train components, accessory parts, seals, gaskets, carburetors, exhaust manifold, hoses, all fuel system components, injectors,
injection pump, turbocharger, muffler, any filters, radiator, thermostat, spark plugs, glow plugs, fuel transfer pumps. The warranty period begins
on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON B&S ENGINES. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED,
THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR ENGINE WARRANTY
B&S welcomes warranty repair and apologizes to you for being
inconvenienced. Any Authorized Briggs & Stratton 3/LC Service
Dealer may perform warranty repairs. Most warranty repairs are
handled routinely, but sometimes requests for warranty service
may not be appropriate. For example, warranty would not apply
if engine damage occurred because of misuse, lack of routine
maintenance, shipping, handling, warehousing or improper
installation. Similarly, warranty is void if the serial number of the
engine has been removed or the engine has been altered or
modified.
If a customer differs with the decision of the Service Dealer, an
investigation will be made to determine whether the warranty
applies. Ask the Service Dealer to submit all supporting facts to
the Distributor or the Factory for review. If the Distributor or the
Factory decides that the claim is justified, the customer will be
fully reimbursed for those items that are defective. To avoid
misunderstanding which might occur between the customer and
the Dealer, listed below are some of the causes of engine failure
that the warranty does not cover.
grit, or other abrasive material that has entered the engine
because of improper maintenance, is not covered by warranty.
This warranty covers engine related defective material
and/or workmanship only, and not replacement or refund of
the equipment to which the engine may be mounted. Nor
does the warranty extend to repairs required because of:
1. Engines that are not properly applied to equipment. It is
strongly recommended that the factory be contacted prior
to applying a B&S 3/LC engine to equipment that did not
originally use a B&S 3/LC engine.
2. PROBLEMS CAUSED BY PARTS THAT ARE NOT
ORIGINAL BRIGGS & STRATTON PARTS.
3. Equipment controls or installations that prevent starting,
cause unsatisfactory engine performance, or shorten
engine life. (Contact equipment manufacturer.)
4. Leaking carburetors, clogged fuel pipes or injectors,
sticking valves, contaminated injection pumps, or other
damage, caused by using contaminated or stale fuel. Use
clean, fresh fuel (lead free gasoline, diesel fuel) and Briggs
& Stratton fuel stabilizer, Part No. 5041.
5. Parts which are scored or broken because an engine was
operated with insufficient or contaminated lubricating oil,
or an incorrect grade of lubricating oil (check oil level daily
or after every 8 hours of operation. Refill when necessary
and change oil and oil filter at recommended intervals.)
OIL GARD may not shut down running engine. Engine
damage may occur if oil level is not properly maintained.
Read Operating & Maintenance Instructions.
6. Repair or adjustment of associated parts or assemblies
such as clutches, transmissions, remote controls, etc.,
which are not manufactured by B&S.
7. Damage or wear to parts caused by dirt, which entered the
engine because of improper air cleaner maintenance,
re-assembly, or use of a non-original air cleaner element
or cartridge. (At recommended intervals, replace
cartridge.) Read Operating & Maintenance Instructions.
8. Parts damaged by over-speeding, or overheating caused
by grass, debris, or dirt, which plugs, clogs radiator or air
cooling access openings, or damage caused by operating
the engine in a confined area without sufficient ventilation.
Engine damage caused by not using accurate mix of
anti-freeze and tap water, or water entering the engine due
to any cause.
9. Engine or equipment parts broken by excessive vibration
caused by a loose engine mounting, loose cutter blades,
unbalanced blades or loose or unbalanced impellers,
improper attachment of equipment to engine crankshaft,
over-speeding or other abuse in operation.
10. Routine tune-up or adjustment of the engine.
11. Engine or engine component failure, i.e., combustion
chamber, valves, valve seats, valve guides, or burned
starter motor windings, caused by the use of alternate
fuels such as, liquified petroleum, natural gas, altered
gasolines, etc.
Warranty is available only through service dealers which
have been authorized by Briggs & Stratton. Locate your
nearest Authorized B&S 3/LC Service Dealer through our
Normal wear:
Engines, like all mechanical devices, need periodic parts service
and replacement to perform well. Warranty will not cover repair
when normal use has exhausted the life of a part or an engine.
Improper maintenance:
The life of an engine depends upon the conditions under which it
operates, and the care it receives. Some applications, such as
tillers, pumps and rotary mowers, are very often used in dusty or
dirty conditions, which can cause what appears to be premature
wear. Such wear, when caused by dirt, dust, spark plug cleaning
19
|