IHT3817DT
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1. Read these instructions. All the safety
and operating instruction should be read
before the product is operated.
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use
a mounting accessory recommended by the
manufacturer.
system is grounded so as to provide some
protection against voltage surges and built-
up static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper ground-
ing of the mast and supporting structure,
grounding of the lead-in wire to an antenna
connection to grounding electrodes, and
requirements for the grounding electrode.
2. Keep these instructions. The safety and
operating instruction should be retained for
future reference.
12. A product and cart combination should
be moved with care. Use only with the cart,
stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
When a cart is used, use caution when mov-
ing the cart/apparatus combination to avoid
injury from tip-over.
3. Heed all warnings. All warning on the
product and in the operating instructions
should be adhered to.
4. Follow all instructions. All operating
and use instructions should be followed.
5. Water and Moisture: Do not use this
product near water - for example, near
a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement, or near a
swimming pool, and the like. The apparatus
shall not be exposed to dripping or splashing
and that no objects filled with liquids, such
as vases, shall be placed on apparatus.
20. Wall or Ceiling Mounting: The prod-
uct should be mounted to a wall or ceiling
only as recommended by the manufacturer.
13. Lightning: Unplug this apparatus and
disconnect the antenna or cable system
during lightning storms or when unused
for long periods of time. This will prevent
damage to the product due to lightning and
power-line surges.
6. Cleaning: Clean only with a dry cloth.
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners.
21. Where the AC plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
7. Do not block any ventilation openings.
Install in accordance with the manufactur-
er’s instructions. Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface.
14. Servicing: Do not attempt to service
this product yourself as opening or remov-
ing covers may expose you to dangerous
voltage or other hazards . Refer all servicing
to qualified service personnel.
22. Ventilation: Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should
not be placed in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
15. Power Sources: Only connect to
the type of house-hold power supply as
indicated in the operating instructions and
rating label. If you are not sure of the type
of power supply to your home, consult your
product dealer or local power company. For
products intended to operate from battery
power, or other sources, refer to the operat-
ing instruction.
8. Heat: Do not install near any heat
sources such as radiators, heat registers,
stoves, or other apparatus (including ampli-
fiers) that produce heat.
23. Protective Attachment Plug: The
product is equipped with an attachment plug
having overload protection. This is a safety
feature. See Instruction Manual for replace-
ment or resetting of protective device. If
replacement of the plug is required, be sure
the service technician has used a replace-
ment plug specified by the manufacturer
that has the same overload protection as the
original plug.
9. Grounding or Polarization: Do not
defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong. The wide blade or
the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
16. Overloading: Do not overload wall
outlets or extension cords as this can result
in a risk of fire or electric shock.
17. Object and Liquid Entry: Never push
objects of any kind or spill liquid into this
product through openings as this could result
in a risk of fire or electric shock.
24. Power Lines: An outside antenna sys-
tem should not be located in the vicinity of
overhead power lines or other electric light
or power circuits, or where it can fall into
such power lines or circuits. When installing
an outside antenna system, extreme care
should be taken to keep from touching such
power lines or circuits as contact with them
might be fatal.
18. Replacement Parts and Safety Check:
When replacement parts are required, be
sure the service technician has used replace-
ment parts specified by the manufacturer.
Ask the service technician to perform
safety checks to ensure proper operation to
avoid possible fire, electric shock, or other
hazards.
10. Power-Cord Protection: Protect
the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11. Accessories: Only use attachments/ac-
cessories specified by the manufacturer.
Do not place this product on an unstable
cart, stand tripod, bracket, or table. The
product may fall, causing serious injury to
a child or adult, and serious damage to the
19. Outdoor Antenna Grounding: If an
outside antenna or cable system is connected
to the product, be sure the antenna or cable
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
Features
12:00
1
2
17
18
19
3
20
4
5
6
7
8
21
9
10
VOLUME
11
22
23
OPEN/CLOSE
12
TUNING
FUNCTION
F
13
14
15
16
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
Features Defined
1
LCD Display View the Time, PM Indicator, iPod Indicator, Aux Input Indicator, AV Input Indicator, EQ
Mode, and Radio Frequency through this Liquid Crystal Display.
2
AV Inputs 1-4 Connect an audio or audio/video source, such as a CD or DVD player, to one of these four
inputs. Note that inputs ꢁ and ꢂ are paired with AVꢁ S-Video and AVꢂ S-Video inputs. The S-Video Inputs
provide improved picture quality.
3
4
5
6
RESET Press the RESET button using a paperclip or like object to restore factory default settings on the
unit.
Mini-USB Use this mini-USB port to connect the unit to a computer and sync your iPod directly from the
player’s docking station.
Sync / Play When the included USB cord is connected, use this toggle switch to change control between the
unit and a computer.
Video Out Plug the yellow connector of an AV Cord in the Video Output to send a video signal from an iPod
to a display with a composite video input.
7
8
9
Subwoofer Output Use the SW Line-out to connect the unit to an external Subwoofer.
S-Video Output Connect your display via the S-Video Output for improved picture quality.
PLAY/PAUSE Press the PLAY/PAUSE button to play or pause an iPod.
10 POWER Press the POWER button to turn the unit on or off.
11 VOLUME Press the (+) button to increase the volume and the (-) button to decrease the volume.
12 OPEN/CLOSE Press the OPEN/CLOSE button to extend and retract the motorized iPod dock.
13 TUNING Press the (+) and (-) buttons to cycle through different radio frequencies.
14 FUNCTION Press the F button to switch between iPod, radio, AUX (AUX In), iPod 2 (iPod Shuffle port),
AV1, AVꢀ, AVꢁ, or AVꢂ control.
15 iPod Shuffle Use the iPod shuffle port to connect a first generation iPod shuffle to the player.
16 Headphone Jack Use the Headphone Jack to plug in a set of headphones (not included).
17 iPod Motorized Docking Station Select the correct insert and connect your iPod, iPod mini, or iPod nano.
18 FM Antenna The FM detachable and extendable antenna provides flexibility and range when adjusting the
FM reception.
19 AM Antenna The AM detachable antenna provides flexibility and range when adjusting the AM reception.
20 Fuse (T1.6L/ꢀ50V Fuse) If this fuse is blown, unplug the unit and replace it with an equivalent type.
21 AUX In Use the AUX In port to connect external audio source to the unit.
22 Wall Mount After removing the table top stand, use the Wall Mount when attaching the player to a wall.
• To ensure a reliable and sturdy installation, please consult a professional installer before mounting the unit
to a wall.
23 Wall Mount Brackets Screw the Wall Mount Brackets into a wall stud before hanging the unit onto the
brackets.
24 AC Cord (1ꢀ0V ~ 60 Hz) The attached AC Cord provides power to the player.
25 Table Stand Use the Table Stand when placing the player on an entertainment center, table, or desk.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Peripherals
35
26
36
37
38
27
28
39
40
41
29
30
42
43
31
32
33
44
45
46
34
Buttons that are not defined in the Peripherals Defined
section, are defined in the Features Defined section.
iPod Inserts
Model
iPod mini
#
ꢁ
ꢂ
5
6
7
8
9
iPod Capacity
ꢂGB, and 6GB
ꢀ0GB, and Uꢀ Special Edition
ꢂ0GB
iPod
ꢀ0GB, ꢁ0GB, and Uꢀ Special Edition
ꢂ0GB
iPod with color display
iPod nano
1GB, ꢀGB, and ꢂGB
ꢁ0GB
iPod with video
10 60GB, and 80GB
iPod nano (second generation)
11 ꢀGB, ꢂGB, and 8GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Peripherals Defined
26 REPEAT Press the REPEAT button to set an iPod to repeat one song, or all songs.
27 CHAPTER Press up on the CHAPTER button to increase the chapter number, or press
down on the CHAPTER button to decrease the chapter number.
28 ALBUM Press up or down on the ALBUM button to cycle through the iPod’s albums.
29 FUNCTION Press the FUNCTION button to switch between radio, iPod Docking Station
and iPOD SHUFFLE port.
30 AUX Press the AUX button to switch the between AV1-ꢂ inputs..
31 MENU Press the MENU button to enter the menu on an iPod.
32 CLOCK With the power off, press and hold the CLOCK button to set the clock.
33 FL Press the FL buttons to adjust the balance of the unit’s left speaker.
34 BASS Press the BASS buttons to adjust the bass level.
35 MUTE Press the MUTE button to decrease the volume entirely.
36 SLEEP/SNOOZE Press the SLEEP/SNOOZE button to set the sleep timer (5 - 90 min-
utes), or activate the snooze (5 minutes) after the alarm has gone off.
37 TIMER Press the TIMER button to set the unit to come on or turn off at a certain time.
38 MEMORY Press MEMORY buttons to cycle up and down through preset radio stations.
39 PLAYLIST Press the PLAYLIST buttons to cycle up and down through the playlists on an
iPod.
40 EQ Press the EQ button to switch equalizer modes between Classic, Jazz, Rock, Pop, Flat,
SRS (SRS TruBass®), ꢁD (ꢁD Enhanced Audio).
41 MEM Use the MEM button to save stations to the unit’s memory.
42 Navigation Controls/SELECT Use the Navigation Controls to move through an iPod
menu system, change the radio station, or set the clock. Press the SELECT button to select
a song, photo, or video on your iPod, or when the power is off, use the SELECT button to
set the clock.
43 SHUFFLE Press the SHUFFLE button to randomly play songs on an iPod.
44 DISPLAY Press the display button to cycle between the clock and the current function.
45 FR Press the FR buttons to adjust the balance of the unit’s right speaker.
46 TREBLE Press the TREBLE buttons to adjust the treble level.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Operations
Setting the Clock
a. With the unit off, press the CLOCK button on the remote.
b. When the time begins to blink on the LCD Display, press the SKIP UP button to
cycle up through the hour and press the SKIP DN button to cycle up through the
minute.
c. Wait 9 seconds, and the clock will be set with the specified time.
Setting the Timer
a. With the player off, press the TIMER button to cycle through the different timer
options (timer ON, timer OFF, ON, and OFF).
b. At the “timer on” or “timer off” functions, indicated by “ON” or “OFF” followed
by a time, press the IPOD FWD/HR button to cycle up through the hour and press
the IPOD REW/MIN button to cycle up through the minute.
c. After the “timer on” and/or “timer off” functions are set, press the TIMER button
until the LCD Display reads “ON” by itself.
d. Wait for 5 seconds and the timer functions will be set with the specified time.
Saving Radio Stations to the Memory
a. Press the FUNCTION button consecutively until the FM or AM radio mode is on.
b. Tune to the desired station.
c. Using the Remote Control, press the MEM button.
d. Press the IPOD FWD/HR. and IPOD REV/MIN buttons to select a Preset to save
the current station under.
e. After the preset has been selected press the MEM button. The current radio fre-
quency is now saved to the selected preset.
continued
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Operations
Viewing Video or Photos from your iPod on an External Device
a. Connect a composite video cable from the player’s video out jack to a composite
video input jack on a TV. You can also connect the player to a TV with an S-Video
cable. (composite video cable not included)
b. Insert your iPod Video into the player and navigate to either the Photos or Videos
on the iPod.
c. On the iPod, select either Slideshow Settings in Photos or Video Settings in Videos.
d. On the iPod, set the TV Out setting to On.
e. Press the FUNCTION button until the player’s mode is set to IPOD, as indicated on
the LCD Display.
f. Make sure your external viewing device is set to the proper input. You will now be
able to control your iPod from the player’s control panel and remote, and view your
iPod on a video display.
Connecting Other Digital Audio Devices
a. Use a line-in cord to connect an iPod shuffle or other audio device to the line-in
port. (line-in cord included)
b. Press the FUNCTION button to set the player to AV 1, ꢀ, ꢁ, or ꢂ mode, as indicated
by the LCD Display.
c. An iPod shuffle or other audio devices other will now play through the speakers of
the player.
Operations that are not listed in the operations section, are explained in the Features Defined or
Peripherals Defined sections.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Table Stand
The attached table stand can be removed by unscrewing the four dark colored screws. It is
recommended that you remove the table stand when mounting the unit on a wall.
12:00
SCREWS
12:00
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Wall Mount
WALL
16 inches
Hanging the wall mount is as easy as screwing the
two included brackets into the wall and hanging the
player on them. It is recommended that you use ꢁ
screws to secure each individual bracket to the wall.
VOLUME
OPEN/CLOSE
TUNING
FUNCTION
F
Be sure to drill the brackets into the studs of the wall
to ensure a firm and sturdy hold. Most houses have
the studs spaced on 16 inch centers.
To ensure a reliable and sturdy installation, please consult a professional installer before
mounting the unit to a wall.
!
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Service Information
Address ꢀ116 Carr Street, St. Louis MO, 6ꢁ106
Phone
Fax
1-ꢁ1ꢂ-6ꢀ1-ꢀ881
1-ꢁ1ꢂ-588-1805
Email
Website www.ilive.net
To download this Instruction Man- Para descargar este manual de Pour télécharger ce manuel
ual in English, Spanish, or French instrucción en inglés, español, o d’instruction en anglais, espagnol,
visit the Support section at
francés visite la sección de la ayu- ou le Français visitez la section de
iPod not included. iPod is a trademark of Apple Inc., registered in the U.S. and other countries. TruBass, SRS and the SRS logo are trademarks
of SRS Labs, Inc. All other trademarks appearing herein are the property of their respective owners. © ꢀ007 DPI, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|