USER’S GUIDE
V:1247-0119-10
IC600B
Intelli Set™ Clock Radio with Dock for iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
fcc Warnings
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
additional Warnings
•
The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux écla-
boussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
•
Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the
apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facile-
ment accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débran-
chée du secteur.
•
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
•
•
Caution marking is located at the rear of the apparatus.
Les marquages sont inscrits de derrière de l’appareil.
The marking information is located at the bottom of apparatus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
dual alarm clock radio With dock for iPod
features
•
•
•
•
Dock plays and charges iPod
Intelli Set™ auto clock set
AM/FM radio with digital tuning
Auxiliary input for iPod shuffle and other
audio devices
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dual alarm with gradual wake
Station memory presets (20AM, 20FM)
Preset EQ settings
Last station memory
Volume & function last user setting
Digital clock
Wake to iPod, radio, or buzzer
Snooze function
Sleep function
Battery backup
Time zone button
Daylight savings time switch
0.8” LCD display with white backlight
Display dimmer control
included
• IC600B
• Docking Brackets for iPod
4
iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
taBle of contents
introduction
setuP
6
8
clock
9
alarm
11
12
13
14
16
iPod
radio
aux inPut
comPany information
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
introduction
PRESET (±) / AL1 / AL2
Press to cycle through
saved radio stations, or
to set alarm 1 or 2.
SNOOZE
Press to delay the alarm
for an additional 9 min-
utes, or to set the sleep
timer.
EQ / DISP
Press to adjust the equal-
izer or press and hold
view the clock when in
radio mode.
CLK ADJ / SOURCE
Press to set the clock or
to adjust the source.
REW / FWD / TUNE /
HR / MIN
VOLUME
Press to skip or search
through tracks on a
docked iPod, tune the
radio, or adjust the hour
and minute when setting
the clock or alarm.
AL OFF/POWER
Press to cancel the alarm
until the set alarm time is
reached, or to power the
clock radio off and on.
PLAY/PAUSE/MEM
Press to play or pause a
docked iPod, or to save
the current radio station
as a preset.
DISPLAY
DOCK FOR IPOD
BACKUP BATTERY
COMPARTMENT
6
iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME ZONE
Press to adjust the Time
Zone.
RESET
Press to reset the clock
radio to it’s default
settings.
DST
Use to turn Daylight Sav-
ings Time off or on.
DIMMER
Press repeatedly to
adjust the brightness of
the display.
FM ANTENNA
POWER INPUT
AUX INPUT
Use to connect an MP3
player or other audio
source to the clock radio.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
setuP
Power
Connect the attached AC cord to a
standard AC outlet to power the clock
radio.
Battery Backup
Requires 1 CR2032 battery (pre-
installed)
The backup battery is for saving the
time during brief power outages. The
unit cannot preform all of its normal
functions when powered off of the
backup battery alone.
radio antennas
Extend the fm Wire antenna to
improve the reception of the FM radio.
An am antenna is built into the clock
radio. Adjust the position of the clock
radio to improve AM radio reception.
8
iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
clock
intelli set™ clock set
The Intelli Set™ time feature
automatically sets the unit’s time to
Eastern Standard.
1 Press the PoWer button to turn the
unit off.
AKST
YST
HST
PST
MST
CST
EST
AST
2 Press and hold the time Zone
button.
A2
A7
A3
A1
A6
A5
3 While holding the time Zone
button, press the hr/min buttons,
on the top of the clock radio, to
adjust the time zone.
A4
TIME ZONE
AST
LCD INDICATOR
A1 (+1 HR)
A2 (±0 HR)
A3 ( -1 HR)
A4 ( -2 HR)
A5 ( -3 HR)
A6 ( -4 HR)
A7 ( -5 HR)
Use the map to the left to find your
time zone.
EST (Default)
CST
4 Release the time Zone button to
finish setting the clock.
MST
PST
AKST or YST
HST
setting the clock manually
Follow the “Intelli Set™ Clock Set”
instructions before attempting to set
the clock manually.
1 Press and hold the clk adJ button.
2 While holding the clk adJ button,
press the hr/min buttons on the top
of the clock radio to adjust the hour
and minute.
3 Release the clk adJ button to finish
setting the clock.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
clock
daylight savings time
The Daylight Savings Time feature is
meant to be activated in the Spring at
the time of the Summer Solstice, and
deactivated in the Autumn at the time
of the Winter Solstice.
DST Activated
The DST should be activated during the Sum-
mer Solstice.
1 At the time of the Summer Solstice,
press the PoWer button to turn the
unit off.
2 Press and hold the clk adJ button.
3 While holding the clk adJ button,
press the dst button to activate the
Daylight Savings Time feature.
DST Deactivated
The DST should be deactivated during the
Winter Solstice.
4 At the time of the Winter Solstice,
repeat steps 1-3 to deactivate the
Daylight Savings Time feature.
setting the sleep timer
The Sleep Timer can only be set when
the clock radio is powered on.
1 Press the PoWer button to power
the clock radio on.
Sleep Timer
The above image shows the sleep timer is set
for 20 minutes. After a few seconds, the “20”
will disappear. To view the remaining time,
press the SNOOZE button once.
2 Press the source button to select
the desired mode (iPod, AM radio, FM
radio, or Aux).
3 Press the snooZe button repeatedly
to set the sleep timer.
When the set time expires, the unit will
power off automatically.
10 iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
alarm
setting the alarms
1 Press and hold the al1 (Alarm 1) or
al2 (Alarm 2) button.
2 While holding the al1 or al2
button, press the hr/min buttons on
the top of the clock radio to adjust
the hour and the minute of the
alarm.
LCD Display After Alarms are Set
The above image shows alarm 1 set to sound
to the buzzer, and alarm 2 set to sound to a
docked iPod.
3 While continuing to hold the al1
or al2 button, press the source
button to adjust the alarm source.
Buzz - Wake to Buzzer
LCD Display During Setting of Alarm
The above image shows alarm 2 is being set to
sound to the AM radio. The time will blink dur-
ing the setting of the alarm.
Tune FM - Wake to the FM radio
Tune AM - Wake to the AM radio
iPod - Wake to a docked iPod
4 Release the al1 or al2 button to
finish setting the alarm.
To cancel the alarm, press the AL1 or
AL2 button twice. The alarm source
icon on the display will disappear.
When the alarm sounds
When the Alarm Sounds, you can either
turn the alarm off until the set alarm
time is reached again, or you can press
the snooZe button to delay the alarm
for an additional 9 minutes.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B 11
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod
docking an iPod
1 Locate the numbered bracket that
fits the iPod model that will be
docked.
Each included bracket has a number
on it, indicating which iPod model that
bracket is compatible with. See the
separate bracket chart page to identify
which bracket is needed.
2 Snap the bracket into place over the
iPod connector in the dock.
3 Connect the iPod to the iPod
connector inside the dock.
When the clock radio is plugged into a
power source, it will charge the docked
iPod.
Playing a docked iPod
1 Press the PoWer button to turn the
clock radio on.
2 Press the source button to switch
to iPod mode.
3 Press the Play/Pause/mem button
to begin playing the docked iPod.
iPod charging
Please note, a docked iPod will charge in
all modes except for AM radio mode.
12 iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
radio
tuning the am/fm radio
1 Press the PoWer button to turn the
clock radio on.
2 Press the source button to switch
to AM or FM radio mode.
3 Press the tune (+ / -) buttons to
tune the AM or FM radio.
saving a radio station as a Preset
1 After tuning the AM or FM radio to
the desired station, press the Play/
Pause/mem button.
The Preset number will begin to blink
on the display.
2 Press the Preset ( + / - ) buttons to
adjust the preset number.
3 Press the Play/Pause/mem button
to save the current AM or FM radio
station as a preset to the selected
number.
selecting a Preset radio station
1 Press the PoWer button to turn the
clock radio on.
2 Press the source button to switch
to AM or FM radio mode.
3 Press the Preset ( + / - ) buttons
to cycle through your preset radio
stations.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B 13
Download from Www.Somanuals.com. All Manuals Search And Download.
aux inPut
using the aux input
1 Press the PoWer button to turn the
clock radio on.
2 Press the source button to switch
to AUX mode.
3 Connect an MP3 player or other
audio source to the aux inPut.
Connecting an audio source to the
AUX INPUT requires a cord with a
3.5mm mini-phono plug.
4 Use the connected device’s controls
to play, pause, stop, and skip
between tracks.
14 iLive | IC600B
Download from Www.Somanuals.com. All Manuals Search And Download.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | IC600B 15
Download from Www.Somanuals.com. All Manuals Search And Download.
comPany information
green initiative
environmental Commitment to ‘Protect for
today and sustain for tomorrow’
2009 marks the official launch of DPI, Inc.’s
corporate campaign for a greener and cleaner
world. DPI and its four brands, iLive, WeatherX,
Capri, and GPX, are building upon environmental
initiatives introduced at all of their facilities to help
formulate and sustain significant and important
conservation efforts within its manufacturing and
marketing communities. In addition to targeting
and selecting energy efficient product features, and
structuring ‘green office’ procedures, other initial
program efforts include:
•
•
Reduction of all packaging sizes
Recyclable plastics for clamshell packages,
with a plan to eventually replace plastic with
recyclable paper
•
•
Recycled fiber board in place of the polyfoam in
packing boxes
Recycled plastics in place of the virgin material
in product construction
international support
To download this User’s Guide in English,
Spanish, or French, visit the support section at
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda en
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section de
contact information
Address: 2116 Carr Street, St. Louis MO, 63106
Phone: 1-314-621-2881
Fax: 1-314-588-1805
Email: [email protected]
Parts Email: [email protected]
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are
subject to change without notice
Download from Www.Somanuals.com. All Manuals Search And Download.
|