NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
Hardware Identifier
Assembly Instruction
Parts List
MWM-8150
Resistance Chart
Warranty
Ordering Parts
Model
MWM-8150
Retain This
Manual for
Reference
08-04-08
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are
missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in
the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that
this machine to be assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Insert the two Guide Rods (#7) into the holes on the Rear Base Frame (#2). Secure it
with two M10 x 1” Allen Bolts (#71) and Ø ¾” Washers (#80) from the bottom. Slide
two Ø 2 ½” Rubber Bumpers (#53) onto the Guide Rods from top to bottom.
B.) Attach the Vertical Frame (#4) onto the Main Base Frame (#1). Secure it with two M10
x 2 ½” Carriage Bolts (#65), one 4 ¾” x 2” Bracket (#23), two Ø ¾” Washers (#80), and
two M10 Aircraft Nuts (#82).
C.) NOTE: Do not tighten all the Nuts and Bolts until instructed to do so.
D.) Attach the Main Base Frame to the Rear Base Frame. Attach the Vertical Support
Frame (#3) onto the Rear Base Frame. Align the holes. Secure them together with two
M10 x 2 ¾” Carriage Bolts (#66), two Ø ¾” Washers (#80), and two M10 Aircraft Nuts
(#82).
E.) Attach the top of Vertical Support Frame to the Vertical Frame. Secure it with two M10
x 5/8” Allen Bolts (#70) and two Ø ¾” Washers (#80).
F.) Attach the two Foot Plates (#22) to the front of Main Base Frame from each side. Align
the holes. Secure the two Foot Plates to the Main Base Frame with two M10 x 2 ½”
Carriage Bolts (#65), two Ø ¾” Washers (#80), and two M10 Aircraft Nuts (#82).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide 14 Weight Plates (#33) onto the Guide Rods. Make sure the deep groove
on the Weight Plates all facing the front of the machine and downward. Insert the
Selector Rod (#28) through the center hole on the Weight Plates. Slide the
Selector Stem (#32) onto the Guide Rods. Use the L-shaped Pin (#39) to select
total weights to exercise. Please refer to the Weight Resistance Chart in page 22.
B.) Place the Upper Frame (#5) onto the Vertical Frame (#4). Secure them with one
M10 x 2 ¾” Allen Bolt (#75), two Ø ¾” Washers (#80), and one M10 Aircraft Nut
(#82) from the side. One M10 x 2 ¾” Allen Bolt (#75), one 1 7/8” Square Bracket
(#25), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82) from front.
C.) Attach the holes on the Top Socket Assembly (#6) onto the two Guide Rods (#7).
Secure it with two M10 x 1” Allen Bolts (#71) and two Ø ¾” Washers (#80).
D.) Attach the other end of Top Socket Assemble to the Upper Frame. Secure it with
one M10 x 2 ¾” Allen Bolts (#75), one M10 x 2 ½” Allen Bolt (#74), two Ø ¾”
Washers (#80), one 4” x 2” Bracket (#24), one Ø ¾” Washer (#80), and one M10
Aircraft Nuts (#82).
E.) Attach the Weight Stack Cover (#27) to Rear Base Frame (#2) and Top Socket
Assembly. Secure it with four M10 x 5/8” Allen Bolts (#70) and four Ø ¾” Washers
(#80).
F.) Securely tighten all Nuts and Bolts previously installed in Sept-1 and Step-2.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Seat Support (#8) to the Vertical Frame (#4). Secure it with two M10 x 2 ½”
Carriage Bolts (#65), one 4 ¾” x 2” Bracket (#23), two Ø ¾” Washers (#80), and two M10
Aircraft Nuts (#82). Do not tighten the Nuts and Bolts yet.
B.) Attach the two Seat Support Frames (#10) to the Seat Support and the Main Base frame (#1)
from each side. Secure them to the Seat Support and Main Base Frame with two M10 x 2 ¾”
Allen Bolts (#75), four Ø ¾” Washers (#80), and two M10 Aircraft Nuts (#82).
C.) Securely tighten all Nuts and Bolts installed in this step.
D.) Attach the Seat Pad (#31) to Main Seat Support. Secure it with two M8 x 2 ½” Allen Bolts
(#78) and two Ø 5/8” Washers (#79).
E.) Attach two Ø 1” Bushings (#44) to the hole on the Leg Developer (#9). Attach the Leg
Developer to the open bracket on Main Seat Support. Secure it with one M12 x 3” Allen Bolt
(#67), two Ø 1” Washers (#81), and one M12 Aircraft Nuts (#63).
F.) Insert two Foam Tubes (#21) halfway through the holes on Main Seat Support and Leg
Developer. Push four Foam Rolls (#41) onto the Tubes from each end. Plug four Foam Roll
End Caps (#60) into the Ends.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach two Ø 1” Bushings (#44) to the holes on the Upper Frame (#5). Attach the Front
Press Base (#11) to the two Bushings. Secure it with one M12 x 4 1/8” Allen Bolt (#68), two
Ø 1” Washers (#81), and one M12 Aircraft Nuts (#63). Do not over tighten the Nut and
Bolt. Make sure the Front Press Base is able to move smoothly.
B.) Attach the Right Butterfly (#13) to the Front Press Base. Secure it with one M12 x 4 3/8”
Allen Bolt (#69), two Ø 1” Washer (#81), and one M12 Aircraft Nut (#63).
C.) Repeat the Steps B above to install the Left Butterfly (#12).
D.) Attach a Butterfly Pulley Bracket (#15) to the Vertical Frame (#4). Secure it with one M10 x
3 ½” Allen Bolt (#77), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82).
E.) Attach one Swivel Pulley Brackets (#16) to each end of the Butterfly Pulley Bracket. Secure
each Bracket with one M10 x 2 ½” Allen Bolt (#74), two Ø ¾” Washers (#80), and one M10
Aircraft Nut (#82). Do not over tighten! Make sure the Brackets are able to swivel freely.
F.) Attach the Backrest Board (#30) to the Vertical Frame. Secure it with two M8 x 2 ½” Allen
Bolts (#78) and Ø 5/8” Washers (#79).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 153” Upper Cable (#34) to the opening at the front of the Upper
Frame (#5). Note: The Ball Stopper on the cable should be underneath the
Frame.
B.) Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt
(#74), two Ø 7/8” x 5/8” Pulley Bushings (#43), and one M10 Aircraft Nut (#82).
C.) Draw the Cable towards the back of the machine to the opening on the Upper
Frame. Attach a Pulley to the opening. Secure it with one M10 x 3” Allen Bolt
(#76), two Ø 7/8” x ¾” Long Pulley Bushings (#42), and one M10 Aircraft Nut
(#82).
D.) Draw the Cable around the Pulley then pull back towards the open bracket on
the Front Press Base (#11).
E.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#72),
two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82).
F.) Draw the Cable around the Pulley through the hole on the Vertical Frame to the
open bracket on the rear of Vertical Frame (#4). Repeat Procedure E above to
install another Pulley.
G.) Draw the Cable around the Pulley then downward. Attach the Cable to in
between the two Double Floating Pulley Brackets (#29). Repeat Procedure E to
install a Pulley. Let the bracket hanging for now.
H.) Draw the Cable around the Pulley then pull the Cable upward to the open
bracket on the Top Socket Assembly (#6).
I.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#73), one
L-shaped Cable Retainer (#26), two Ø ¾” Washers (#80), and one M10 Aircraft
Nut (#82).
J.) Draw the Cable to the other open bracket on the Top Socket Assembly. Repeat
Procedure I to install another Pulley.
K.) Pull the Cable downward between the two Guide Rods, through a Ø 1 ¾” Rubber
Bumper (#52) to the Selector Rod (#28). Fully thread the bolt at the end of the
Cable into the top opening on the Selector Rod.
L.) Connect the Lat Bar (#19) to the Upper Cable with a C-clip (#38).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 125” Butterfly Cable (#35) to the hook on the Right Butterfly (#13).
B.) Draw the Cable to the right Swivel Pulley Bracket (#16).
C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#72), two Ø ¾”
Washers (#80), and one M10 Aircraft Nut (#82).
D.) Draw the Cable around the Pulley then downward. Attach the Cable to a Crossed Double
Floating Pulley Bracket (#17). Install another Pulley. Let the Bracket hang for now.
E.) Pull the Cable around the Pulley then upward to the left Swivel Pulley Bracket. Repeat
Procedure C above to install a Pulley.
F.) Draw the Cable to the left Butterfly. Attach the end to the hook on the Left Butterfly.
G.)Push one Butterfly Foam Roll (#40) onto the Right Butterfly. Attach a Front Press Handle
(#14) to the Right Butterfly. Secure it with one M10 x 2 ¾” Allen Bolt (#75) and Ø ¾” Washer
(#80). Repeat the same procedure to install the Foam Roll and Handle to Left Butterfly.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 131” Lower Cable (#36) to the opening on the bottom of the Leg
Developer (#9).
B.) Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#74), two Ø
7/8” x 5/8” Pulley Bushings (#43), and one M10 Aircraft Nut (#82).
C.) Draw the Cable underneath the Pulley to the opening in between the two Seat
Support Frames (#10).
D.) Attach a Pulley to the opening. Secure it with one M10 x 2 ¾” Allen Bolt (#75), two Ø
¾” Washers (#80) and one M10 Aircraft Nut (#82). Insert a M10 x 2 ½” Allen Bolts
(#74) through the hole on the two Seat Support Frames under the Pulley. Secure the
Bolt with two Ø ¾” Washers (#80) and one M10 Aircraft Nut (#82).
E.) Draw the Cable underneath the Pulley along the Main Base Frame to the opening on
the bottom of the Vertical Frame (#4). Repeat Procedure B above to install another
Pulley.
F.) Pull the Cable upward to the Crossed Double Floating Pulley Bracket (#17)
previously installed in Step-6. Install another Pulley with one M10 x 1 ¾” Allen Bolt
(#72), two Ø ¾” Washers (#80) and one M10 Aircraft Nut (#82).
G.) Draw the Cable over the Pulley then downward to the opening on the bottom of
Vertical Support Frame (#3). Repeat Procedure B to install another Pulley.
H.) Pull the Cable around the Pulley then upward to the Double Floating Pulley Bracket
(#29) previously installed in Step-5. Install another Pulley with one M10 x 1 ¾” Allen
Bolt (#72), two Ø ¾” Washers (#80) and one M10 Aircraft Nut (#82).
I.) Draw the Cable around the Pulley then pull downward to the bracket on the back of
the Vertical Support Frame. Secure the Cable to the bracket with one M10 x 1” Allen
Bolt (#71), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82).
J.) Adjust the tension of the Cable by adjusting the Pulley position on the Double
Floating Pulley Bracket (#29). If the cables are too loose, move the Pulley up one
hole. If the cables are too tight, move the Pulley down one hole.
K.) For best performance of the machine, adjust the Cables so the Selector Stem (Top
Plate) on the weight stack is ¼” above the first plate. To select the weight, push
down on the Selector Stem to close the gap then insert the selector pin. This will
remove the slack in the cable system so the range of motion is smooth and tight.
L.) Connect the Shiver Bar (#20) to a Chain (#37) with a C-clip (#38). Connect the
Chain to the Lower Cable with another C-clip.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 7
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
4 1/8” x 2 1/8” Rubber Bumper
Ø 1 ¾” Rubber Bumper
Ø 2 ½” Rubber Bumper
Ø 1 ½” Rubber Bumper
Ø 1 ½” Bushing
1
1
2
1
4
2
7
1
2
4
1
1
4
1
6
2
1
1
2
6
5
8
2
8
8
1
1
4
4
61
8
34
1
1
1
1
2
3
4
5
6
7
8
Main Base Frame
Rear Base Frame
Vertical Support Frame
Vertical Frame
Upper Frame
Top Socket Assembly
Guide Rod
Seat Support
Leg Developer
Seat Support Frame
Front Press Base
Left Butterfly
1
1
1
1
1
1
2
1
1
2
1
1
1
2
1
2
Ø 1 ¾” End Cap
2” Square End Cap
Ø 1” Cone-shaped End Cap
Ø 1” End Cap
Foam Roll End Cap
Single Handle
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Ankle Strap
M12 Aircraft Nut
Right Butterfly
M6 x 5/8” Philips Screw
M10 x 2 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M12 x 3” Allen Bolt
M12 x 4 1/8” Allen Bolt
M12 x 4 3/8” Allen Bolt
M10 x 5/8” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 3” Allen Bolt
M10 x 3 ½” Allen Bolt
M8 x 2 ½” Allen Bolt
Ø 5/8” Washer
Front Press Handle
Butterfly Pulley Bracket
Swivel Pulley Bracket
Crossed Double Floating Pulley Bracket1
Rotating Ring
Lat Bar
Shiver Bar
Foam Tube
Foot Plate
4 ¾” x 2” Bracket
4” x 2” Bracket
1 7/8” Square Bracket
L-shaped Cable Retainer
Weight Stack Cover
Selector Rod
Double Floating Pulley Bracket
Backrest Board
Seat Pad
Selector Stem
Weight Plate
153” Upper Cable
125” Butterfly Cable
131” Lower Cable
Chain
2
1
1
2
2
2
1
2
2
1
1
2
1
1
1
14
1
1
1
1
3
1
2
4
2
8
4
4
4
16
1
6
1
Ø ¾” Washer
Ø 1” Washer
M10 Aircraft Nut
#5 Allen Wrench (Tool)
#6 Allen Wrench (Tool)
#8 Allen Wrench (Tool)
C-Clip
L-shaped Pin
Butterfly Foam Roll
Foam Roll
Ø 7/8” x ¾” Long Pulley Bushing
Ø 7/8” x 5/8” Pulley Bushing
Ø 1” Bushing
Plastic Ring
Rivet
Pulley
Main Base Frame End Cap
Handle Grip
1 7/8” x 1 7/8” Rubber Bumper
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|