NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
MWM 1801
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 1801
Retain This
Manual for
Reference
08-18-03
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine to be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket
(#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90).
DIAGRAM 1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10
x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90). NOTE:
Do not tighten the Nuts and Bolts yet.
B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10
x 2 ½” Carriage Bolt (#82), ∅ ¾” Washer (#93), and M10 Aircraft Nut (#90).
C.) Attach the Right Seat Support (#8) to the Right Vertical Beam (#2). Secure it with one
Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two
M10 Aircraft Nuts (#90).
D.) Attach the Leg Developer (#9) to the Right Seat Support (#8). Secure it with one M10 x 2”
Axle (#56), two M10 x ¾” Allen Bolts (#86), and two ∅ ¾” Washers (#93). NOTE: Do not
over tighten the bolts. Make sure the Leg Developer is able to swivel.
DIAGRAM 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Align four ∅ 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame
(#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the
Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a
Selector Rod (#24) through the hole on each Selector Stem. Secure each Selector
Rod to the Selector Stem with two M10 x 1” Allen Bolts (#78) and ∅ ¾” Washers
(#93). Please note this machine comes with 18 plates, 9 to each stack. You can
purchase another 5 more plates (Model no. WK51) in the future to increase the
weights. It is strongly recommended to spay lubricant such as WD-40 on the two
Guide Rods to minimize friction.
B.) Attach the Right Upper Frame (#6) to the top of Right Vertical Beam (#2). Secure it
with a Pulley Bracket (#46), two M10 x 2 ½” Carriage Bolts (#82), two Ø ¾” Washers
(#93), and two M10 Aircraft Nuts (#90).
C.) Attach the Top Socket Assembly (#7) to the four Guide Rods. Make sure the Guide
Rods are inserted into the holes on the Top Socket Assembly. Secure the Top Socket
Assembly to the Guide Rods with four M10 x 1” Allen Bolts (#78) and ∅ ¾” Washers
(#93).
D.) Secure the Top Socket Assembly (#7) to the Right Upper Frame (#6) with two M10 x
2 3/8” Carriage Bolts (#80), ∅3/4” Washers (#93) and M10 Aircraft Nuts (#90).
E.) Carefully tilt over the machine with a help of another person. Secure the Guide Rods
(#5) to the Right Base Frame (#1) with four ∅ ¾” Washers (#93) and M10 x 1” Allen
Bolts (#78).
F.) Securely tighten all Nuts and Bolts previously installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two
M10 x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90).
B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left
Vertical Beam. Secure the Frame to the Left Vertical Beam with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90). Secure the Frame to the Top Socket Assembly with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90).
C.) Attach the Left Seat Support (#14) to the Left Base Frame (#3) and the Left Vertical
Beam (#4). Secure it to the Left Base Frame with one M10 x 2 ½” Carriage Bolt
(#82), ∅ ¾” Washer (#93), and M10 Aircraft Nut (#90). Secure it to the Vertical
Beam with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾”
Washers (#93), and two M10 Aircraft Nuts (#90).
D.) Attach the Leg Press Frame (#17) to the bracket on the Left Base Frame (#3).
Secure it with one M12 x 3” Allen Bolt (#77), two ∅ 1” Washers (#92), and one M12
Aircraft Nut (#89). Do not over tighten the Nut and Bolt. Make sure the Leg Press
Frame is able to swivel.
E.) Attach the Leg Press Support Frames (#18) to both side of the Leg Press Frame
(#17). Secure them together with two M10 x 2 ½” Carriage Bolts (#82), ∅ ¾”
Washers (#93), and M10 Aircraft Nuts (#90).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a
M10 x 9 ¼” Axle (#50), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90).
B.) Attach the two Front Presses (#16) to the Front Press Base (#15). Secure each
Front Press with two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93),
and two M10 Aircraft Nuts (#90).
DIAGRAM 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame
(#11) from the bottom up. Slide a ∅ 1 ½” Washer (#54) and ∅ 1 3/8” Lock Ring (#53)
onto the Axle. Align the holes and secure the Ring with a M6 x 1 5/8” Hex Bolt (#87)
and M6 Aircraft Nut (#91). Repeat the same procedure to install the other side.
B.) Push two Butterfly Foam Rolls (#39) onto the Butterfly arms.
DIAGRAM 6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Loop Diagram for Butterfly Station
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Loop Diagram for Bench Press Station
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each
Bracket with one M12 x 4 3/8” Allen Bolt (#76), two ∅1” Washers (#92) and one M12 Aircraft
Nut (#89). NOTE: Do not over tighten the Bolt. Make sure the Bracket is able to swivel.
B.) Attach one end of the 83” Butterfly Cable (#29) to the clip on the Right Butterfly (#13). Pull
the Cable to the right open Swivel Pulley Bracket (#42).
C.) Attach a Pulley (#65) to the Bracket. Secure it with one M10 x 2 “Allen Bolt (#81), two ∅ ¾”
Washers (#93), and one M10 Aircraft Nut (#90).
D.) Draw the Cable downward. Repeat Step B above to install a Pulley to the Angled Double
Pulley Bracket (#45). Let the Bracket hanging for now. Pull the Cable upward to the left
open Swivel Pulley Bracket.
E.) Repeat Step B above to install another Pulley to the Left Swivel Pulley Bracket. Draw the
Cable to the Left Butterfly (#12). Attach the end of the Cable to the clip on the Left Butterfly.
DIAGRAM 7
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8”
Allen Bolt (#83), two ∅ 3/4” Washers (#93), and one M10 Aircraft Nut (#90). Attach one
end of the 136” Butterfly Support Cable (#31) to the Chain using a C-clip (#63). NOTE:
After complete installing all the cables, check the tightness of the cable loop system. If
the cable is too loose, shorten the chain.
B.) Draw the Cable to the Angled Double Pulley Bracket (#45) previously installed.
C.) Attach a Pulley to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾”
Washers (#93), and one M10 Aircraft Nut (#90).
D.) Pull the Cable around the Pulley then downward. Repeat Step C above to install a
Pulley to a Single Floating Pulley Bracket (#43). Let the Bracket hanging for now. Draw
the Cable underneath the Pulley then upward through the Left Upper Frame (#11) to
the open Bracket on the top.
E.) Attach a U-shaped Bracket (#49) to the Bracket. Repeat Step C above to install a
Pulley. Draw the Cable over the Pulley then pull the Cable downward to the Selector
Rod (#24). Thread the tip bolt of the Cable into the Selector Rod.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9 & Cable Loop Diagram)
A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat
Support (#14), underneath the rubber bumper. Secure it with one M10 x 2 3/8” Allen
Bolt (#79), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
B.) Draw the Cable to the slotted opening on the Leg Press Frame (#17). Install a Pulley to
the opening then secure it with two ∅5/8” x ½” Pulley Bushings (#58), one M10 x 2 3/8”
Allen Bolt (#79), and one M10 Aircraft Nut (#90).
C.) Draw the Cable around the Pulley then toward the opening on the Left Seat Support
(#14). Repeat the Step B above to install a Pulley.
D.) Draw the Cable over the Pulley then downward to the open bracket on the Left Base
Frame (#3). Attach a Pulley to the Bracket then secure it with one M10 x 2” Allen Bolt
(#81), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
E.) Draw the Cable underneath the Pulley and towards the back of the machine, along the
Left Base Frame to the lower opening on the Left Vertical Beam (#4). Repeat Step B
above to install a Pulley. Draw the Cable around the Pulley then pull back towards the
lower opening on the Front Press Base (#15).
F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#75), two ∅ ¾”
Washers (#93), and one M10 Aircraft Nut (#90).
G.)Draw the cable around the Pulley then pull the Cable towards the open bracket on the
Left Vertical Beam. Attach a U-shaped Bracket (#49) to the open Bracket. Install
another Pulley. Secure them with one M10 x 2” Allen Bolt (#81), two ∅ ¾” Washers
(#93), and one M10 Aircraft Nut (#90).
H.) Draw the Cable around the Pulley then back to the upper opening on the Front Press
Base (#15). Repeat Step F above to install another Pulley.
I.) Draw the Cable around the Pulley then towards the upper slotted opening on the Left
Vertical Beam (#4). Repeat Step B above to install a Pulley.
J.) Draw the Cable over the Pulley then downward to the open bracket on the Left Base
Frame. Install a Pulley. Secure the Pulley with an L-shaped Bracket (#48), one M10 x 2”
Allen Bolt (#81), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
K.) Draw the Cable underneath the Pulley then pull the Cable upward to the Single Floating
Pulley Bracket (#43) previously installed. Secure the Cable with one M10 x 1 3/8”” Allen
Bolt (#83), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 9
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Diagram 10 & Cable Loop Diagram)
A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6).
NOTE: The Ball Stopper on the Cable needs to be underneath the Frame.
B.) Attach a Pulley (#65) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅
5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90).
C.) Draw the Cable towards the back of the machine to the Pulley Bracket (#46). Install a Pulley
to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), one L-shaped Bracket (#48), two
∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
D.) Pull the Cable over the Pulley then downward. Attach a Pulley to a Double Floating Pulley
Bracket (#44). Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾” Washers (#93), and
one M10 Aircraft Nut (#90). Let the Bracket hanging for now.
E.) Pull the Cable around the Pulley then upward to the open bracket on the back of the Top
Socket Assembly (#7). Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt
(#81), U-shaped Bracket (#49), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).
F.) Pull the Cable around the Pulley then downward to the Selector Rod (#24). Thread the bolt
at the end of the Cable into the Selector Rod.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Diagram 11 & Cable Loop Diagram)
A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach
a Pulley to the opening. Secure the Pulley with one M10 x 2 3/8” Allen Bolt (#79), two
∅ 5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90).
B.) Pull the AB Cable around the Pulley then downward. Attach the end of Cable to a
Chain (#51). Secure the Cable to the Chain with one M10 x 1” Allen Bolt (#78), two ∅
¾” Washers (#93), and one M10 Aircraft Nut (#90). Let the Chain hanging for now.
C.) Attach the 171” Lower Cable (#27) to the opening on the Leg Developer (#9). Attach a
Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ 5/8” x
½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90). Draw the Lower Cable
underneath the Pulley through the opening on the Right Seat Support (#8) then to the
open bracket on the Right Base Frame (#1).
D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾”
Washers (#93), and one M10 Aircraft Nut (#90).
E.) Draw the Lower Cable underneath the Pulley along the Right Base Frame and
through the opening on the Right Vertical Beam (#2) to the second open bracket on
the Right Base Frame. Attach a L-shaped Bracket (#48) to the bracket then repeat
Step D above to install a Pulley.
F.) Pull the Cable underneath the Pulley then upward to the Double Floating Pulley
Bracket (#44) previously installed. Repeat Step D above to install a Pulley.
G.)Draw the Cable around the Pulley then pull the Cable downward to the first Bracket
on the Right Base Frame. Install another Pulley.
H.) Pull the Cable around the Pulley then upward to the Chain (#51). Connect the Cable
to the end of the Chain using a C-clip (#63).
I.) Check the tightness of the Cable loop system. If the cable loop is too loose, shorten
the chain.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 11
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12 (See Diagram 12)
A.) Now move the machine to its final position. After installing the weight stack, it will be too heavy to
move. Check and tighten all Nuts and Bolts previously installed.
B.) Install 9 Weight Plates (#36) to each set of Guide Rods (#5). To install the plate, lift up the
Selector Rod in the center, hold the plate at an angle and place between the two Guide Rods then
drop it down. NOTE: Make sure the groves on the plastic covers all face the same direction. The
caps should interlock with each other.
C.) Align the center holes on all plates. Insert the Selector Rod (#24) into the center holes on the
plates. Insert the Weight Selector Pin (#52) into the selected stack of Weight Plates to obtain the
desired weight for exercise. Make sure the magnet on the Pin faces up. It is strongly
recommended to spray lubricant such as WD-40 on the two Guide Rods to minimize friction.
D.) Attach the Backrest Board (#23) to the Right Vertical Beam (#2). Secure it with two M8 x 2 1/8”
Allen Bolts (#84) and ∅ 5/8” Washers (#94).
E.) Place the Seat (#22) onto the Right Seat Support (#8). Secure it with two M8 x 2 1/8” Allen Bolts
(#84) and two ∅ 5/8” Washers (#94).
F.) Attach the Arm Curl Pad (#21) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8” Allen Bolts
(#85) and ∅ 5/8” Washers (#94). Insert the Arm Curl Stand into the top opening on the Right Seat
Support. Use a M18 Lock Knob (#64) to hold the desired height for Arm Curl exercise.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13 (See Diagram 13)
A.) Insert one Foam Tube (#34) halfway through the hole on the Right Seat Support (#8). Insert
one Foam Tube (#34) halfway through the hole on the Leg Developer (#9). Push four Foam
Rolls (#38) onto the Tubes from both sides. Plug the Foam Roll End Caps (#74) into the ends.
B.) Attach the Lat Bar (#20) to the Chain (#51) using a C-clip (#63). Attach the Chain to the Upper
Cable (#26). See How To Use.
C.) Attach the AB Strap (#25) to the AB Cable (#30) using a C-clip.
D.) Attach the Arm Curl Handle (#32) to a Chain (#51) using a C-clip. Attach the Chain to the
Lower Cable (#27). Remove the Chain and Handle when using the Leg Developer.
DIAGRAM 13
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 14 (See Diagram 14)
A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secure it with two M8 x 2 1/8”
Allen Bolts (#84) and ∅ 5/8” Washers (#94).
B.) Place the Seat (#22) onto the Left Seat Support (#14). Secure it with two M8 x 2 1/8” Allen
Bolts (#84) and two ∅ 5/8” Washers (#94).
C.) Attach the Leg Press Plate (#19) to the Leg Press Frame (#17). Secure it with a L-Shaped
Pin (#62).
DIAGRAM 14
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE
How to use the quick release connector.
The Clip is removed from the Connector.
Connector
Clip
Place the chain in between the connector
and insert the Clip through the holes.
Chain
Insert
Push down the Clip to secure.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Right Base Frame
Right Vertical Beam
Left Base Frame
Left Vertical Beam
Guide Rod
Right Upper Frame
Top Socket Assembly
Right Seat Support
Leg Developer
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
2
2
18
36
4
2
2
4
2
1
1
1
1
5
3
4
1
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Chain
4
2
2
2
2
1
4
14
2
8
2
1
5
1
25
1
2
4
1
1
2
Weight Selector Pin
Ø 1 3/8” Lock Ring
Ø 1 ½” Washer
Butterfly Axle
M10 x 2” Axle
Ø 1 3/8” Selector Stem Bushing
Ø 5/8” x ½” Pulley Bushing
Ø 1 3/8” x 1” Bushing
Ø 5/8” Bushing
∅ ½” Bushing
L-shaped Pin
C-clip
M18 Lock Knob
Pulley
Ø 1 ½” x 5/8” Rubber Bumper
Ø 1 5/8” x 1 5/8” Rubber Bumper
Ø 2 ½” x 1” Rubber Bumper
1 ½” Square End Cap
1 ¾” Square Sleeve
2” Square End Cap (Impex Logo)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Arm Curl Stand
Left Upper Frame
Left Butterfly
Right Butterfly
Left Seat Support
Front Press Base
Front Press
Leg Press Frame
Leg Press Support Frame
Leg Press Plate
Lat Bar
Arm Curl Pad
Seat
Backrest Board
Selector Rod
AB Strap
114” Upper Cable
171” Lower Cable
140” Leg Press Cable
83” Butterfly Cable
39” AB Cable
136” Butterfly Support Cable
Arm Curl Handle
Curl Bar Handle Tube
Foam Tube
Selector Stem
Weight Plate
Weight Plate Cover
Foam Roll
Butterfly Foam Roll
Lat Bar Grip
1 ¾” Square End Cap (Impex Logo) 19
1 ½” Square End Cap (Impex Logo)
Foam Roll End Cap
M10 x 8 ¼” Allen Bolt
M12 x 4 3/8” Allen Bolt
M12 x 3” Allen Bolt
M10 x 1” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 2” Allen Bolt
M10 x 2 ½” Carriage Bolt
M10 x 1 3/8” Allen Bolt
M8 x 2 1/8” Allen Bolt
M8 x 5/8” Allen Bolt
M10 x ¾” Allen Bolt
M6 x 1 5/8” Hex Bolt
M6 x 5/8” Philips Screw
M12 Aircraft Nut
2
4
2
2
1
13
8
2
16
24
2
8
2
2
2
3
3
57
2
6
82
11
M10 Aircraft Nut
M6 Aircraft Nut
∅ 1” Washer
Ø ¾” Washer
Handle Grip
Swivel Pulley Bracket
Single Floating Pulley Bracket
Double Floating Pulley Bracket
Angled Double Pulley Bracket
Pulley Bracket
Ø 5/8” Washer
Bracket
L-shaped Bracket
U-shaped Bracket
M10 x 9 ¼” Axle
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MWM 1801 Weight Resistance Chart
Weight Plate
Station
Low Pulley
Lat Pull
1
2
42
42
42
26
100
63
3
54
53
54
32
134
82
4
5
6
7
8
9
30
31
30
20
66
44
66
78
90
102
97
114
108
114
62
126
119
126
68
64
75
86
Ab Strap
Butterfly
Leg Press
Front Press
66
78
90
102
56
38
44
50
168
101
202
120
236
139
270
158
304
177
338
196
*Each plate weights 10 lb.
*Resistance measured in pounds.
*Numbers are approximate. Actual number may vary.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|