Impex Home Gym MWB CR 4 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

MARCY CORNER GYM

CR 4

Resistance Chart

How to Use

Warranty

Ordering Parts

Model

MWB CR 4

Retain This

Manual for

Reference

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

6-18-01

info@impex-fitness.com

OWNER'S

MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you

operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or

operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.

THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS

WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING

ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL

INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS

PRODUCT.

SAVE THESE INSTRUCTIONS.

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY INSTRUCTION

Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches

NOTE: It is strongly recommended this machine be assembled by two or more people to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each

other. Attach the Rear Vertical Beam (#5) to the joint and align the holes. Secure the top hole

with a M10 x 2 ¾” Carriage Bolt (#90), Æ3/4” Washer (#106) and M10 Aircraft Nut (#110). Secure

the bottom hole with a M10 x 2 ½” Allen Bolt (#97) and Æ ¾” Washer (#106). DO NOT tighten all

the nuts and bolts yet.

B.) Attach the Guide Rod Base (#24) diagonally to the two Base Frames. Secure it with a M10 x 2 ½”

Allen Bolt (#97) and Æ1 ¼” Washer (#104) on each side on the Base.

C.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure it with two M10 x 2 ¾”

Carriage Bolts (#90), Æ3/4” Washers (#106), and M10 Aircraft Nuts (#110). Repeat the same

procedure to install the Left Vertical Beam (#4).

Diagram 1

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 2 (See Diagram 2)

A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two

M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two Æ3/4” Washers (#106), and two

M10 Aircraft Nuts (#110).

B.) Attach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M10 x 2 ½”

Allen Bolt (#97), Æ ¾” Washer (#106), and 4” x 2” Bracket (#39) into the upper hole. Secure the

bottom hole with one M10 x 2 ¾” Carriage Bolt (#90), Æ ¾” Washer (#106), and M10 Aircraft Nut

(#110).

C.) Attach both Left and Right Upper Frame (#7) & (#6) to the Rear Vertical Beam (#5). Secure it with

a M10 x 2 ½” Allen Bolt (#97) and Æ ¾” Washer (#106) to the upper hole. Secure the bottom hole

with a M10 x 2 ¾” Carriage Bolt (#90), Æ ¾” Washer (#106) and M10 Aircraft Nut (#110).

D.) Align two Rubber Bumpers (#63) to the holes on the Guide Rod Base (#24). Push two Guide

Rods (#31) into the holes. Slide the Selector Stem (#44) onto the Guide Rods. Slide the Selector

Stem over the Selector Rod (#43). Please note this machine comes with 14 plates. You can

purchase another 5 more plates in the future to increase the weights. For now, drop the Selector

Stem down on the Selector Rod so there are 14 grooves underneath it. Secure it with a M10 x 1 ¾”

Allen Bolt (#98). DO NOT install the plates yet.

E.) Place the Top Socket Assembly (#25) over the top of the two Guide Rods. Secure it with two M6 x

5/8” Allen Bolts (#103).

F.) Secure the Top Socket Assembly (#25) to both Upper Frames (#6) & (#7) with a M10 x 2 ½” Allen

Bolt (#97) and Æ1 ¼” Washer (#104) on each side.

G.) Securely tighten all nuts and bolts previously installed.

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 3 (See Diagram 3)

A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2

¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two Æ ¾” Washers (#106) and two M10 Aircraft

Nuts (#110).

B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them with two

M10 x 2 ¾” Carriage Bolts (#90), Æ ¾” Washers (#106), and M10 Aircraft Nuts (#110).

DIAGRAM 3

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 4 (See Diagram 4)

A.) Attach four Æ1” x ½” Bushings (#55) to the Leg Press Pivot Arm (#18). Attach the Pivot Arm to the

bracket on the Right Base Frame (#1). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two

Æ 1” Washers (#105), and one M12 Aircraft Nut (#109).

B.) Attach two Æ1”x1/2” Bushings (#55) to the tube on the Leg Press Frame (#19). Attach the Leg

Press Frame (#19) to the top of the Pivot Arm (#18). Secure it with one M12 x 3 1/8” Hex Head

Bolt (#91), two Æ 1” Washers (#105), and one M12 Aircraft Nut (#109).

C.) Attach two Æ1”x1/2” Bushings (#55) to the pivot tube on the Right Base Frame (#1).

D.) Attach four D-Shaped Bushings (#57) to the top and bottom holes on the Leg Press Crank (#17).

Repeat for the other Crank. Attach the two Cranks to the pivot tube on the Right Base Frame (#1).

Secure them with a M12 x 5 11/16” Bolt (#94), two Æ1” Washers (#105), and one M12 Aircraft Nut

(#109).

E.) Repeat the same procedure D above to install the Cranks to the Leg Press Frame (#19).

DIAGRAM 4

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 5 (See Diagram 5)

A.) Insert the Chromed Adjustment Tube (#20) into the Leg Press Frame (#19). Secure it with a

Quick Release Pin (#62).

B.) Attach the Foot Plate (#21) to the Chromed Tube (#20) and secure it with a L-Shaped Pin (#112).

C.) Attach the Bench Press Frame (#11) to the pivot tube on the Right Base Frame (#1). Insert a M10

x 8 5/8” Axle (#82) through the holes. Secure it with two Æ ¾” Washers (#106) and M10 Aircraft

Nuts (#110) on both sides. Close the ends with two Round Caps (#108).

D.) Attach two Bench Press Handles (#12) to the Bench Press Frame (#11). Secure them with two

Quick Release Pins (#62).

E.) Attach the Seat (#40) to the Seat Support Frame (#14). Secure it with two Æ5/8” Washers (#107)

and M8 x 2 ½” Allen Bolts (#101).

F.) Attach the Backrest Board (#41) to the Right Vertical Beam (#3). Secure it with two Æ 5/8”

Washers (#107) and M8 x 2 ½” Allen Bolts (#101).

DIAGRAM 5

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 6 (See Diagram 6)

A.) Attach the Butterfly Support Frame (#8) to the front of the Right Vertical Beam (#3). Attach the

Butterfly Pulley Support (#113) to the back of the Right Vertical Beam (#3). Secure them with two

M10 x 3” Carriage Bolts (#89), Æ ¾” Washers (#106), and M10 Aircraft Nuts (#110).

B.) Insert the axle on the Right Butterfly (#10) into the hole on the Butterfly Support Frame (#8) from

the bottom up. Secure it with a Æ1 ½” Washer (#59) and M12 Aircraft Nut (#109). Close the end

with a Round Cap (#108). Slide the Butterfly Foam (#67) onto the Arm. Repeat the same

procedure to install the Left Butterfly (#9).

C.) Attach a Butterfly Pulley Bracket (#29) to the bottom of the Butterfly Pulley Support (#113).

Secure it with a M12 x 4 5/16” Bolt (#93), Æ1” Washer (#105), and M12 Aircraft Nut (#109).

Repeat to install another Bracket.

DIAGRAM 6

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 7 (See Diagram 7)

A.) Attach the Leg Developer Frame (#15) to the Left Vertical Beam (#4). Secure it with two M10 x 2

¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two Æ ¾” Washers (#106), and two M10

Aircraft Nuts (#110).

B.) Attach the Leg Developer Frame (#15) to the Left Base Frame (#2). Secure it with a M10 x 2 ¾”

Carriage Bolt (#90), Æ ¾” Washer (#106), and M10 Aircraft Nut (#110).

C.) Place a Æ1 ½” Ring (#114) onto the pivot axle on the Left Base Frame (#2). Then slide the Swivel

Frame (#26) onto the axle. Secure it with a Æ ¾” Washer (#106) and M10 x 1” Allen Bolt (#99).

D.) Attach the Backrest Board (#41) to the Left Vertical Beam (#4). Secure it with two Æ5/8”

Washers (#107) and M8 x 2 ½” Allen Bolts (#101).

E.) Attach two Æ1” x 5/8” Bushings (#54) to the holes on the Rear Vertical Beam (#5). Attach the

Vertical Press Frame (#13) to the holes. Insert a M12 x 3 ¾” Axle (#81) through the holes. Secure

it with two Æ1” Washers (#105) and M12 Aircraft Nuts (#109). Close the ends with two Round

Caps (#108).

F.) Lubricate the inside of the two Foam Grips (#65) with water. Slide them onto the Vertical Press

Frame (#13).

DIAGRAM 7

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 8 (See Diagram 8)

A.) Attach the Seat (#40) to the Leg Developer Frame (#15). Secure it with two Æ5/8” Washers

(#107) and M8 x 2 ½” Allen Bolts (#101).

B.) Attach both Left Handlebar (#32) and Right Handlebar (#33) to the Leg Developer Frame (#15)

underneath the Seat (#40). Secure them with two M10 x 2 ¾” Carriage Bolts (#90), Æ ¾” Washers

(#106), and M10 Aircraft Nuts (#110).

C.) Attach two Æ1” x ½” Bushings (#55) to the Leg Developer (#23). Attach the Leg Developer to the

bracket on the Leg Developer Frame (#15). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91),

two Æ 1” Washers (#105), and one M12 Aircraft Nut (#105).

D.) Insert two Foam Roll Tubes (#37) halfway through the holes on the Leg Developer (#23) and Leg

Developer Frame (#15). Push four Foam Rolls (#66) onto the tubes from both sides. Close the

ends with four 2” Round End Caps (#74). Insert a L-Shaped Pin (#112) into the hole on the

bracket on the Leg Developer Frame (#15) to lock the Leg Developer (#23) in place. Remove

the Pin when using.

E.) Attach the Arm Curl Pad (#42) to the Arm Curl Stand (#22). Secure it with two Æ5/8” Washers

(#107) and M8 x 5/8” Allen Bolts (#102).

F.) Insert the Arm Curl Stand (#22) into the opening on the Leg Developer Frame (#15). Secure it

with a Quick Release Pin (#62).

DIAGRAM 8

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 9 (See Diagram 9 & 15)

A.) Attach a Pulley (#58) to the bracket on the Right Butterfly Arm (#10). Secure it with one M10 x 1 ¾”

Allen Bolt (#98), two Æ ¾” Washers (#106), and one M10 Aircraft Nut (#110). Repeat to install

another Pulley to the other side.

B.) Attach one end of the 86” Butterfly Cable (#84) to the Right Butterfly Pulley Bracket (#29). Install a

Pulley (#58) to the Bracket and secure it with a M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers

(#106), and a M10 Aircraft Nut (#110).

C.) Draw the Cable over the Pulley on the Right Butterfly Arm (#10). Then draw the Cable to the other

Pulley on the Left Butterfly Arm (#9). Continue drawing the Cable to the Left Butterfly Pulley

Bracket (#29). Install a Pulley following Step B above.

D.) Pull both ends of the Cable (#84) downward until they come together. Attach a Short Chain (#45)

in between the ends. Secure them with one M10 x 1” Allen Bolt (#99), two Æ ¾” Washers (#106),

and one M10 Aircraft Nut (#110).

E.) Attach a Single Floating Pulley Bracket (#27) to the end of the Chain (#45) using a Clip (#88). Let

the Chain hanging for now. NOTE: After completing the whole set up, check the cable loop

system. If the cable loop is too loose, shorten this Chain (#45).

DIAGRAM 9

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 10 (See Diagram 10 & 15)

A.) Attach the Ball-end of the 132” Upper Cable (#85) to the Right Upper Frame (#6). Install a Pulley

(#58). Push two Bushings (#56) into the holes from both sides. Secure it with one M10 x 2 ½”

Allen Bolt (#97) and M10 Aircraft Nut (#110).

B.) Draw the Cable towards the back of the machine along the top of the Right Upper Frame (#6).

Install another Pulley (#58) using one M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers (#106),

and one M10 Aircraft Nut (#110).

C.) Draw the Cable downward through the Frame and install a Pulley to a Single Floating Bracket

(#27). Secure it with one M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers (#106), and one M10

Aircraft Nut (#110). Let the Bracket hanging for now.

D.) Draw the Cable upward towards the top of the Top Socket Assembly (#25). Install another Pulley.

E.) Continue drawing the Cable over the Pulley downward through the hole on Top Socket Assembly

(#25). Thread the end of the Cable into the Selector Rod (#43).

DIAGRAM 10

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 11 (See Diagram 11 & 15)

A.) Attach one end of the 327 ½” Leg Press Cable (#83) to the bracket on the Leg Press Pivot Arm

(#18). (See C View) Secure it with one M10 x 1” Allen Bolt (#99), two Æ ¾” Washers (#106), and

one M10 Aircraft Nut (#110). NOTE: Do not over tighten this bolt. Make sure the head of the

cable can swivel on the bolt.

B.) Draw the Cable to the Vertical Supports (#16). Install a Pulley (#58). Secure it with one M10 x 5”

Allen Bolt (#96), two Æ ¾” Washers (#106), and one M10 Aircraft Nut (#110). Draw the Cable

over this Pulley back to the Leg Press Pivot Arm (#18). Install another Pulley using one M10 x 1 ¾”

Hex Head Bolt (#92), two Æ ¾” Washers (#106), and one M10 Aircraft Nut (#110).

C.) Draw the Cable towards back of the machine to the bottom of the Right Vertical Beam (#3).

Install a Pulley (#58) using one M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers (#106), and

one M10 Aircraft Nut (#110). (See D View)

D.) Draw the Cable over the Pulley back to the Bench Press Frame (#11). Install a Pulley with one

M10 x 8 ½” Axle (#95), two Æ ¾” Washers (#106), and two M10 Aircraft Nuts (#110).

E.) Draw the Cable back to the Right Vertical Beam (#3). Install a Pulley. (See D View).

F.) Draw the Cable to the Bench Press Frame (#11) and install another Pulley.

G.) Draw the Cable back to the Right Vertical Beam (#3) through the hole to the back of the Beam.

Install another Pulley.

H.) Draw the Cable upward to the Single Floating Pulley Bracket (#27) previously installed in STEP

9E. Install another Pulley.

I.) Draw the Cable over the Pulley downward to the bracket on the Right Base Frame (#1). Install

another Pulley.

J.) Draw the Cable all the way up to the bottom of the Right Upper Frame (#6). Install another Pulley.

K.) Then draw the Cable downward to install a Pulley to a Double Floating Pulley Bracket (#30). Let

the Bracket hanging for now.

L.) Finally draw the Cable upward to the Single Floating Pulley Bracket (#27) previously installed in

STEP 10C. Secure the end of the Cable to the Bracket with one M10 x 1” Allen Bolt (#99), two Æ

¾” Washers (#106), and one M10 Aircraft Nut (#110).

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 12 (See Diagram 12 & 15)

A.) Attach the Ball-end of the 158” Ab Cable (#86) to the opening on the Left Vertical Beam (#4).

Install a Pulley (#58). Push two Bushings (#56) from both sides of the Beam. Secure it with a

M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110).

B.) Draw the Cable over the Pulley downward and install another Pulley to a Double Floating Pulley

Bracket (#30). Secure it with one M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers (#106), and

one M10 Aircraft Nut (#110). Let the Bracket hanging for now.

C.) Draw the Cable upward to the bottom of the Vertical Press Frame (#13). Install two Pulleys.

Draw the Cable over the two Pulleys then downward to the bracket on the Left Base Frame (#2).

Install another Pulley.

D.) Draw the Cable across to the bracket on the Right Base Frame (#1). Install a Pulley.

E.) Draw the Cable upward to the Double Floating Pulley Bracket (#30) previously installed in STEP

11K. Install another Pulley to the Bracket.

F.) Finally draw the Cable over the Pulley downward to the Right Base Frame (#1). Secure the end

of Cable to the Frame with a M10 x 1” Allen Bolt (#99), two Æ ¾” Washers (#106), and one M10

Aircraft Nut (#110).

DIAGRAM 12

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 13 (See Diagram 13 & 15)

A.) Attach the Ball-end of the 102” Leg Curl Cable (#87) to the opening on the Leg Developer (#23).

Install a Pulley (#58) to the opening. Attach two Bushings (#56) to the holes on the Leg

Developer. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110).

B.) Pull the Cable through the openings to the bracket on the Left Base Frame (#2). Install a Pulley.

Secure it with a M10 x 1 ¾” Hex Head Bolt (#92), two Æ ¾” Washers (#106), and one M10 Aircraft

Nut (#110).

C.) Continue drawing the cable through the opening on the bottom of the Left Vertical Beam (#4).

Install another Pulley.

D.) Draw the Cable upward to the Double Floating Pulley Bracket (#30) previously installed in STEP

12B. Install another Pulley.

E.) Pull the Cable downward to the Swivel Frame (#26). Install another Pulley.

F.) Slide a Ring Cap (#80), Rubber Ball (#79) and Æ7/8” Washer (#78) onto the end of the Cable.

Screw a Connector (#48) onto the Cable. See E View.

DIAGRAM 13

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 14 (See Diagram 14 & 15)

A.) Tighten all the nuts and bolts previously installed.

B.) Before putting the Weight Plates on, now move the machine to the corner of the room or place

where you will use the machine.

C.) Lift up the Selector Rod and install the Weight Plates. To install the plates, hold the plate at an

angle and place between the two guide rods then drop it down. Make sure the grooves on the

plastic covers all face up. See diagram below. It is strongly recommended to spay some

lubricant such as WD-40 on the two guide rods to minimize friction.

D.) Check the tightness of the cable loop. If the loop is too loose, shorten the chain installed in STEP

9E.

E.) Attach the Weight Stack Cover (#28) to the machine and secure it with four Æ3/4” Washers

(#106) and M10 x ½” Allen Bolts (#100).

DIAGRAM 14

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

KEY NO. DESCRIPTION

Q’ty

Right Base Frame

Left Base Frame

Right Vertical Beam

Left Vertical Beam

Rear Vertical Beam

Right Upper Frame

Left Upper Frame

Butterfly Support Frame

Left Butterfly

Pulley

Æ1 ½” Washer

Grip

Æ1 1/8” Bushing

Quick Release Pin

Rubber Bumper

Rubber Bumper for Leg Developer

Foam Grip

Right Butterfly

Bench Press Frame

Bench Press Handle

Vertical Press Frame

Seat Support Frame

Leg Developer Frame

Vertical Support

Leg Press Crank

Leg Press Pivot Arm

Leg Press Frame

Chromed Adjustment Tube

Foot Plate

Arm Curl Stand

Leg Developer

Guide Rod Base

Top Socket Assembly

Swivel Frame

Single Floating Pulley Bracket

Weight Stack Cover

Butterfly Pulley Bracket

Double Floating Pulley Bracket

Guide Rod

Left Handlebar

Right Handlebar

Lat Bar

Curl Bar

Collar

Foam Roll Tube

4 ¾” x 2” Bracket

4” x 2” Bracket

Seat

Backrest Board

Arm Curl Pad

Selector Rod

Selector Stem

Foam Roll

Butterfly Roam

1 ½” Square Sleeve

2” Square End Cap

1 ¾” Square End Cap

2” Square End Cap

1 ¾” Square End Cap

2” x 1” End Cap

2” Round End Cap

1 ¼” Round End Cap

3 1/8” x 1 9/16” End Cap

2” Square Sleeve

Æ7/8” Washer

Rubber Ball

Ring Cap

M12 x 3 ¾” Axle

M10 x 8 5/8” Axle

Leg Press Cable (327 ½”)

Butterfly Cable (86”)

Upper Cable (132”)

Ab Cable (158”)

Leg Curl Cable (102”)

Clip

M10 x 3” Carriage Bolt

M10 x 2 ¾” Carriage Bolt

M12 x 3 1/8’ Hex Head Bolt

M10 x 1 3/4” Hex Head Bolt

M12 x 4 5/16” Bolt

M12 x 5 11/16” Bolt

M10 x 8 ½” Axle

M10 x 5” Allen Bolt

M10 x 2 ½” Allen Bolt

M10 x 1 ¾” Allen Bolt

M10 x 1” Allen Bolt

M10 x ½” Allen Bolt

M8 x 2 ½” Allen Bolt

M8 x 5/8” Allen Bolt

M6 x 5/8” Allen Bolt

Æ 1 ¼" Washer

Short Chain

Long Chain

Rubber Cushion

Connector

Selector Pin

Weight Plate

Ab Strap

Ankle Strap

Single Handle

Æ1” x 5/8” Bushing

Æ1” x ½” Bushing

Bushing for Pulley

D-Shaped Bushing

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

Æ 1” Washer

Æ ¾” Washer

Æ 5/8” Washer

Round Cap

M12 Aircraft Nut

M10 Aircraft Nut

Æ 1 ½” Bushing

L-shaped Pin

Butterfly Pulley Support

Æ 1 ½” Ring

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO USE

How to use the quick release connector.

The Clip is removed from the

Connector.

Connector

Clip

Place the chain in between

the connector and insert the

Clip through the holes.

Chain

Insert

Push down the Clip to secure.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,

under normal use and service conditions, for a period of two years on the Frame from the date of

purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this

Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX

Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must

be prepaid by the customer. This warranty does not extend to any product or damage to a product

caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs

not provided by a IMPEX authorized service center or for products used for commercial or rental

purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in

connection with the use or performance of the product or other damages with respect to any

economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of

removal, installation or other consequential damages or whatsoever natures. Some states do not

allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above

limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied

warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to

the terms set forth herein. Some states do not allow limitations on how long an implied warranty

lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state

to state.

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

www.impex-fitness.com

info@impex-fitness.com

When ordering replacement parts, always give the following information.

Model

Description of Parts

Part Number

Date of Purchase

Download from Www.Somanuals.com. All Manuals Search And Download.

Grindmaster Coffeemaker OPOD User Manual
Harbor Freight Tools Motorcycle Accessories 97071 User Manual
Harbor Freight Tools Saw 42307 User Manual
Hotpoint Refrigerator HL161I User Manual
HP Hewlett Packard Network Router 2040D User Manual
Huffy Fitness Equipment 211387 User Manual
Hypertec Carrying Case TANCD2HY User Manual
Hyundai Whiteboard Accessories ACCENT User Manual
IBM Laptop SG24 6526 00 User Manual
IBM Personal Computer LCD PC User Manual