NOTE:
Please read all instructions
carefully before using this
product
MARCY PLATINUM
SMITH CAGE
MP-3105
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-3105
Retain This
Manual for
Reference
12-27-06
OWNER'S
MANUAL
IMPEX®
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weight on Rack: 600 lbs.
6. Maximum weight on Smith Bar: 300 lbs.
7. Maximum weight on Weight Holder: 200 lbs.
8. Maximum weight on Leg Developer: 100 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer, and Upper
Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for
replacements. Apply the labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach one Diagonal Support (#3) to the Right Cross Brace (#15). Secure it with one 3
¾” x 2 3/8” Bent Bracket (#26), M10 x 2 3/8” Carriage Bolt (#81), Ø ¾” Washer (#87),
and M10 Aircraft Nut (#89) to the front hole. Secure the back hole with one M10 x 2
1/8” Allen Bolt (#74) and Ø ¾” Washer (#87). Repeat the same procedure to install the
other Diagonal Support to the Left Cross Brace (#14).
C.) Attach the Left & Right Cross Brace (#14 & #15) to the Rear Vertical Beam (#10).
Secure them together with two M10 x 2 ¾” Carriage Bolts (#83), Ø ¾” Washers (#87),
and M10 Aircraft Nuts (#89).
D.) Attach the Foot Plate (#34) to the front of Rear Vertical Beam (#10). Attach the Weight
Glide Post Base (#11) to the back of Rear Vertical Beam. Align the holes and secure
them together with two M10 x 2 3/8” Allen Bolts (#75), four Ø ¾” Washers (#87), and
two M10 Aircraft Nuts (#89).
E.) Secure the Foot Plate (#34) to the Rear Vertical Beam (#10) with one M10 x 3” Allen
Bolt (#77), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#89).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Left Vertical Beam (#1) to the left Diagonal Support (#3). Secure it with two M10
x 2 ¾” Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers
(#87), and two M10 Aircraft Nuts (#89).
B.) Attach one Guide Rod (#5) onto the left Diagonal Support. Secure it with one M10 x 1”
Allen Bolt (#72) and Ø ¾” Washer (#87) from the bottom.
C.) Slide a Ø 2 ½” x 1” Rubber Bumper (#65) and the Left Safety Stop Frame (#7) onto the
Guide Rod from the top.
D.) Attach a Guide Rod Bracket (#4) onto the Guide Rod (#5) and the Left Vertical Beam (#1).
Secure it with three M10 x 1” Allen Bolts (#72) and Ø ¾” Washers (#87).
E.) Repeat Procedure A to D above to install the other side.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Place the Weight Glide Post (#12) onto the Weight Glide Post Base (#11). Secure it
with four M10 x ¾” Carriage Bolts (#79), Ø ¾” Washers (#87) and M10 Aircraft Nuts
(#89).
B.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post.
C.) Attach the Upper Frame (#13) onto the Rear Vertical Beam (#10). Secure it with two
M10 x 3 1/8” Carriage Bolts (#84), one 3 ½” x 1 5/8” Bent Bracket (#28), two Ø ¾”
Washers (#87), and two M10 Aircraft Nuts (#89).
D.) Attach the rear of Upper Frame (#13) to the Weight Glide Post (#12) and secure it with
one 2 ¾” x 1 ¾” Bracket (#29), M10 x 2 3/8” Allen Bolt (#75) and Ø ¾” Washer (#87) to
the upper hole. Secure the lower hole with one M10 x 2 ½” Carriage Bolt (#82), Ø ¾”
Washer (#87), and M10 Aircraft Nut (#89).
E.) Attach one Upper Frame Support (#16) to the Left Vertical Beam (#1). Secure it with
one 2 ¾” x 2” Bent Bracket (#27), M10 x 3 3/8” Allen Bolt (#78) and Ø ¾” Washer (#87)
to the upper hole. Secure the lower hole with one M10 x 3 ½” Carriage Bolt (#85), Ø ¾”
Washer (#87), and M10 Aircraft Nut (#89). Repeat the same step to install the other
Upper Frame Support (#16) to the Right Vertical Beam (#2).
F.) Attach the two Upper Frame Supports (#16) to the Upper Frame (#13) from each side.
Secure them together with two M10 x 2 3/8” Carriage Bolts (#81), Ø ¾” Washers (#87),
and M10 Aircraft Nuts (#89).
G.)Securely tighten all Nuts and Bolts previously installed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Butterfly Base (#17) to the front of Rear Vertical Beam (#10). Attach the Butterfly
Pulley Bracket (#18) to the back of Rear Vertical Beam. Align the holes and secure them with
two M10 x 2” Carriage Bolts (#80), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#89).
B.) Insert the Axle on the Left Butterfly (#19) into the Butterfly Base from the bottom. Secure it
with one Lock Ring (#54), Ø 1 ½” Washer (#53), M6 x 1 ¼” Allen Bolt (#69), and M6 Aircraft
Nut (#88).
C.) Attach a Butterfly Arm Pad (#38) to the Left Butterfly (#19). Secure it with two M8 x 2 ½” Allen
Bolts (#71) and Ø 5/8” Washers (#86).
D.) Repeat Procedure B and C above to install the Right Butterfly (#20).
E.) Attach the Backrest Board (#39) to the Rear Vertical Beam (#10). Secure it with two M8 x 1
¾” Allen Bolts (#70) and Ø 5/8” Washers (#86).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach a 123” Cable (#37) to the front opening on the Upper Frame (#13). Attach a
Pulley (#44) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#75), two Ø 1
1/8” x 3/8” Pulley Bushings (#42), and one M10 Aircraft Nut (#89). Make sure the ball
stopper on the Cable is underneath the Upper Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of
Upper Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt
(#75), two Ø 1 1/8” x 3/8” Pulley Bushings (#42), and one M10 Aircraft Nut (#89).
C.) Draw the Cable around the Pulley then downward. Install a Pulley to the top holes on
the two Double Floating Pulley Brackets (#23). Secure the Pulley with one M10 x 1 ¾”
Allen Bolt (#73), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#89). Let the
Brackets hanging for now.
D.) Draw the Cable around the Pulley then upward to the opening on the top of Weight
Glide Post (#12). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#75), two Ø 1” x ½” Pulley Bushings (#40), and one M10 Aircraft Nut (#89).
E.) Draw the Cable around the Pulley then downward to the Sliding Weight Post (#22).
Secure the Cable to the Sliding Weight Post with one M10 x 1” Allen Bolt (#72), two Ø
¾” Washers (#87), and one M10 Aircraft Nut (#89).
F.) Connect the Lat Bar (#21) to the Cable with a Short Chain (#47) using two Hooks (#48).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 79” Butterfly Cable (#36) to the clip on the Left Butterfly (#19). Draw the
Cable to the left Butterfly Pulley Bracket (#18).
B.) Attach a Pulley (#44) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two ∅ ¾”
Washers (#87), and one M10 Aircraft Nut (#89).
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley
Bracket (#24). Install a Pulley to the Bracket. Let the Bracket hanging for now.
D.) Draw the Cable around the Pulley then upward to the right Butterfly Pulley Bracket. Install
another Pulley. Draw the Cable around the Pulley then clip to the Right Butterfly (#20).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach one 123” Cable (#37) to the lower opening on the Rear Vertical Beam (#10). Attach
a Small Pulley (#45) to the opening. Secure it with a M10 x 2 ¾” Allen Bolt (#76), two Ø 1”
x 5/8” Pulley Bushings (#41), and one M10 Aircraft Nut (#89).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post Base
(#11). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two ∅
¾” Washers (#87), and one M10 Aircraft Nut (#89).
C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket (#23)
previously installed in Step-5. Install a Pulley.
D.) Draw the Cable around the Pulley then downward to the open bracket on the back of Rear
Vertical Beam (#10). Install a Pulley then draw the Cable upward to the Single Floating
Pulley Bracket (#24) installed in Step-6. Secure the end of the Cable to the bracket with
one M10 x 1” Allen Bolt (#72), two ∅ ¾” Washers (#87), and one M10 Aircraft Nut (#89).
E.) Connect the V Bar (#35) to the Cable with a Long Chain (#46) using two Hooks (#48).
F.) Check the tension of the Cables. If the Cables are too loose, adjust the tension by moving
up the Pulley on the Double Floating Pulley Bracket (#23). If the Tension is too tight, then
move down the Pulley.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Note: Help of another person is strongly recommended for this step. Place the Weight
Lifting Sleeve (#6) in between the two Safety Stop Frames (#7 & #8). Align the holes
and insert the Weight Bar (#9) into the Left Safety Stop Frame through the Weight
Lifting Sleeve to the other end of Right Safety Stop Frame. Turn the safety hooks on
the Weight Lifting Sleeve to secure its position on the selected slot of the Vertical
Beams (#1 & #2). Center the Weight Bar and secure it to the Left & Right Safety Stop
Frames with two M8 x 3/8” Allen Bolts (#90) on each end.
B.) Slide two Olympic Sleeves (#50) onto the Sliding Weight Post (#22). Slide two Long
Olympic Sleeves (#51) onto the Weight Bar (#9).
C.) Attach four Spring Clips (#49) to the Olympic Sleeves.
D.) Attach the Left & Right Bar Holders (#32 & #33), Left & Right Safety Catches (#30 &
#31) onto the selected peg on the Left & Right Vertical Beams.
DIAGRAM 8
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the Main Seat Support (#92) to the Rear Stabilizer (#93). Secure it with two M10
x 3 ½” Allen Bolts (#114), one 2 ¾” x 2” Bent Bracket (#27) and two Ø ¾” Washers
(#87).
B.) Attach the Front Post (#94) to the Main Seat Support. Secure it with two M10 x 2 ¾”
Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers (#87),
and two M10 Aircraft Nuts (#89).
C.) Thread two T-shaped Lock Pins (#101) into the holes on the Main Seat Support (#92)
and the Front Post (#94).
DIAGRAM 9
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-10 (See Diagram 10)
A.) Attach the Seat Bracket (#95) to the pivot on the Main Seat Support (#92).
B.) Attach the two Backrest Supports (#97) to the Seat Bracket (#95) and align the holes.
Secure them with a M12 x 8 ½” Allen Bolt (#113), two Ø 1” Washers (#111), and one
M12 Aircraft Nut (#112). Use the T-shaped Lock Pin on the Main Seat Support to lock the
Seat Bracket at desired incline.
C.) Attach the Backrest Incline Support (#96) in between the two Backrest Supports (#97).
Align the holes and secure it with a M12 x 8 ½” Allen Bolt (#113), two Ø 1” Washers
(#111), and one M12 Aircraft Nut (#112). Place the other end of the Support onto the
selected slot on the Main Seat Support.
D.) Do not over tighten the Nut and Bolt. Make sure the Backrest Supports and Backrest
Incline Support are able to swivel.
E.) Insert the Foam Tube Frame (#99) into the opening on the Front Post (#94). Use the T-
shaped Lock Pin to lock the Frame at desired height.
F.) Insert the Foam Tube (#100) half way through the hole on the Foam Tube Frame. Push
two Vinyl Foam Rolls (#106) onto the Tube from both ends. Plug two Foam Roll End
Caps (#108) into the ends.
DIAGRAM 10
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-11 (See Diagram 11)
A.) Place the Seat Pad (#103) onto the Seat Bracket (#95). Secure it with four M8 x 1 5/8” Allen
Bolts (#98) and Ø 5/8” Washers (#86).
B.) Attach the Bench Backrest Board (#104) to the Backrest Supports (#97). Secure it with four
M8 x 1 5/8” Allen Bolts (#98) and Ø5/8” Washers (#86).
DIAGRAM 11
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE EXPLODED DIAGRAM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
3
2
3
1
1
1
1
1
1
1
1
1
2
2
1
2
2
4
4
10
1
1
1
4
4
2
2
4
2
2
1
2
1
3
1
2
3
4
5
6
7
8
9
Left Vertical Beam
59
60
61
62
63
∅ 1” Cone-shaped End Cap
Ø 1” End Cap
2” x 1 ¾” Sleeve
6
2
2
2
2
2
2
Right Vertical Beam
Diagonal Support
Guide Rod Bracket
Guide Rod
Lat Bar Grip
5 ¾” x 2” Rubber Bumper
3 3/8” x 2” Rubber Bumper
Ø 2 ½” x 1” Rubber Bumper
Lifting Sleeve
64
65
Left Safety Stop Frame
Right Safety Stop Frame
Weight Bar
66
Ø 1 ¾” x 1 5/8” Rubber Bumper 1
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
Ø 2” End Cap
2
1
2
2
4
10
7
2
6
1
1
2
4
2
4
1
8
2
2
14
62
2
39
4
2
1
1
1
1
1
2
8
1
1
2
1
1
1
1
2
4
2
1
2
4
2
2
2
1
1
10 Rear Vertical Beam
11 Weight Glide Post Base
12 Weight Glide Post
13 Upper Frame
14 Left Cross Brace
15 Right Cross Brace
16 Upper Frame Support
17 Butterfly Base
M6 x 5/8” Philips Screw
M6 x 1 ¼” Allen Bolt
M8 x 1 ¾” Allen Bolt
M8 x 2 ½” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 3” Allen Bolt
M10 x 3 3/8” Allen Bolt
M10 x ¾” Carriage Bolt
M10 x 2” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3 1/8” Carriage Bolt
M10 x 3 ½” Carriage Bolt
∅ 5/8” Washer
Ø ¾” Washer
M6 Aircraft Nut
M10 Aircraft Nut
M10 x 3/8” Allen Bolt
Wheel
Main Seat Support
Rear Stabilizer
Front Post
18 Butterfly Pulley Bracket
19 Left Butterfly
20 Right Butterfly
21 Lat Bar
22 Sliding Weight Post
23 Double Floating Pulley Bracket
24 Single Floating Pulley Bracket
25 4 3/8” x 2 ¾” Bent Bracket
26 3 ¾” x 2 3/8” Bent Bracket
27 2 ¾” x 2” Bent Bracket
28 3 ½” x 1 5/8” Bent Bracket
29 2 ¾” x 1 ¾” Bracket
30 Left Safety Catch
31 Right Safety Catch
32 Left Bar Holder
33 Right Bar Holder
34 Foot Plate
35 V Bar
36 79” Butterfly Cable
37 123” Cable
38 Butterfly Arm Pad
39 Backrest Board
40 Ø 1” x ½” Pulley Bushing
41 Ø 1” x 5/8” Pulley Bushing
42 Ø 1 1/8” x 3/8” Pulley Bushing
43 Ø 1 1/8” x 5/8” Bushing
44 Pulley
45 Small Pulley
46 Long Chain
47 Short Chain
48 Hook
Seat Bracket
Backrest Incline Support
Backrest Support
M8 x 1 5/8” Allen Bolt
Foam Tube Frame
Foam Tube
T-shaped Lock Pin
Plastic Cover
Seat Pad
Bench Backrest Board
4” Grip
Vinyl Foam Roll
1” Square End Cap
Foam Roll End Cap
1 ¾” Sleeve
Ø 1” E-Clip
Ø 1” Washer
M12 Aircraft Nut
M12 x 8 ½” Allen Bolt
M10 x 3 ½” Allen Bolt
Ankle Strap
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
49 Spring Clip
50 Olympic Sleeve
51 Long Olympic Sleeve
52 1 ½” x 1” Sleeve
53 Ø 1 ½” Washer
54 Lock Ring
55 2” Square End Cap
56 2” Butterfly Base End Cap
57 1 ¾” Square End Cap
58 1 ½” Square End Cap
Single Handle
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX®
LIMITED WARRANTY
®
IMPEX warrants this product to be free from defects in workmanship and material, under normal use and
service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends
only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at
IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Air Conditioner 24R200 User Manual
Haier Clothes Dryer HDY C70 User Manual
HANNspree Flat Panel Television K226 10C1 User Manual
Hans Grohe Indoor Furnishings 10111XX1 User Manual
Hasbro Robotics 6805280000 User Manual
Havis Shields Automobile Accessories C TM EXPD User Manual
Healthrider Treadmill HRTL14911 User Manual
HP Hewlett Packard Laptop 2540P User Manual
HP Hewlett Packard Personal Computer dv9500 User Manual
Ikelite Digital Camera C 60 User Manual