NOTE:
Please read all instructions
carefully before using this
product
MARCY DIAMOND ELITE
SMITH CAGE
Table of Contents
Safety Notice
MD-MXM6
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-MXM6
Retain This
Manual for
Reference
08-3-06
OWNER'S
MANUAL
IMPEX®
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weight on Rack: 300 lbs.
6. Maximum weight on Smith Bar: 300 lbs.
7. Maximum weight on Weight Holder: 200 lbs.
8. Maximum weight on Leg Developer: 100 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer, and Upper
Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for
replacements. Apply the labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the Left & Right Base Frames (#26 & #27) by a Cross Brace (#36) in the mid-
span. Secure each end of the Cross Brace with two M10 x 2 ½” Carriage Bolts (#102),
one 4 3/8” x 1 ¾” Bracket (#56), two Ø ¾” Washers (#89), and two M10 Aircraft Nuts
(#106).
C.) Attach a Front Vertical Beam (#24) to the Left Base Frame (#26). Secure it with two
M10 x 2 ¾” Carriage Bolts (#103), one 4 ¾” x 2” Bracket (#57), two Ø ¾” Washers
(#89), and two M10 Aircraft Nuts (#106). Repeat the same procedure to install the
other side.
D.) Attach the Front Top Beam (#43) to the two Front Vertical Beams. Secure each end
with one M10 x 2 ½” Allen Bolt (#96), 4” x 2” Bracket (#55), and Ø ¾” Washer (#89) to
the top hole. Secure the bottom hole with one M10 x 2 ¾” Carriage Bolt (#103), Ø ¾”
Washer (#89), and M10 Aircraft Nut (#106).
E.) Insert a Guide Rod (#35) into the hole on the Left Base Frame (#26). Secure it with
one M10 x 1” Allen Bolt (#92) and ∅ ¾” Washer (#89) from the bottom.
F.) Slide a Lower Safety Stop Frame (#52) and a Safety Stop Frame (#32) onto the Guide
Rod (#35).
G.) Secure the top of the Guide Rod to the Front Vertical Beam with one M10 x 1” Allen
Bolt (#92) and ∅ ¾” Washer (#89).
H.) Attach a Safety Hook (#53) to the Lower Safety Stop Frame (#52). Secure it with one
M10 x 1” Allen Bolt (#92), two ∅ ¾” Washers (#89), and one M10 Aircraft Nut (#106).
I.) Attach the Safety Hook to the selected hole on the Front Vertical Beam.
J.) Repeat procedures E through I above to install the other side.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Rear Vertical Beam (#38) onto the Cross Brace (#36). Attach the Weight Glide
Post (#34) to the Rear Vertical Beam and Cross Brace. Attach the Foot Plate (#115) to the
Cross Brace. Align the holes and secure them with two M10 x 2 ¾” Carriage Bolts (#103),
∅ ¾” Washers (#89), and M10 Aircraft Nuts (#106).
B.) Slide the Sliding Weight Post (#45) onto the Weight Glide Post (#34).
C.) Place the Upper Frame (#37) onto the Rear Vertical Beam (#38), Weight Glide Post (#34),
and Front Top Beam (#43).
D.) Secure the Upper Frame to the Weight Glide Post (#34) with two M10 x 2 3/8” Allen Bolts
(#95), four ∅ ¾” Washers (#89), and two M10 Aircraft Nuts (#106).
E.) Secure the Upper Frame to the Rear Vertical Beam (#38) with two M10 x 2 3/8” Carriage
Bolts (#100), ∅ ¾” Washers (#89), and M10 Aircraft Nuts (#106).
F.) Secure the Upper Frame to the Front Top Beam (#43) with two M10 x 2 ¾” Carriage Bolts
(#103), one 4 ¾” x 2” Bracket (#57), two ∅ ¾” Washers (#89), and two M10 Aircraft Nuts
(#106).
G.)Slide two Olympic Sleeves (#62) onto the posts on the Sliding Weight Post (#45). Attach a
Spring Clip (#83) to each Sleeve.
H.) Secure the Foot Plate (#115) to the Rear Vertical Beam (#38) with one M10 x 2 ½”
Carriage Bolt (#102), Ø ¾” Washer (#89), and M10 Aircraft Nut (#106).
I.) Securely tighten all nuts and bolts previously installed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Butterfly Base (#39) and Butterfly Pulley Bracket (#44) to the Rear Vertical Beam
(#38). Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#102), ∅ ¾”
Washers (#89), and M10 Aircraft Nuts (#106).
B.) Insert the axle on the Right Butterfly (#41) through the hole on the Butterfly Base. Secure it
with one Lock Ring (#80), M6 x 1 ¼” Allen Screw (#107), and M6 Aircraft Nut (#108).
C.) Push a Butterfly Arm Pad (#58) onto the Right Butterfly.
D.) Repeat Procedures B and C above to install the other side.
E.) Attach the Backrest Board (#33) to the Rear Vertical Beam. Secure it with two M8 x 2 3/8”
Allen Bolts (#104) and ∅ 5/8” Washers (#88).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting
Sleeve (#48) in between the two Safety Stop Frames (#32). Align the holes and insert the
Weight Bar (#49) into the Safety Stop Frame from one end through the Weight Lifting Sleeve
to the other Safety Stop Frame on the opposite end. Center the bar and secure it to each
Safety Stop Frame with two M8 x 3/8” Allen Bolts (#110) on each end.
B.) Turn the safety hook on the Weight Lifting Sleeve to secure its position on the selected holes
on the Front Vertical Beams. Slide two Long Olympic Sleeves (#63) onto the Weight Bar.
Attach two Spring Clips (#83) to the Olympic Sleeves.
C.) Attach four Weight Posts (#42) to the Left & Right Base Frames (#26 & #27). Secure each
Post with one M10 x 1” Allen Bolt (#92) and ∅ ¾” Washer (#89).
D.) Attach four Olympic Sleeves (#62) to the Posts. Attach a Spring Clip (#83) to each Sleeve.
E.) Insert the Left & Right Bar Holders (#28 & #29), Left & Right Safety Catches (#30 & #31) into
the selected holes on the two Front Vertical Beams (#24).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach a 124” Cable (#60) to the front opening on the Upper Frame (#37). Attach a
Pulley (#81) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#94), two Ø 1
1/8” Bushings (#86), and one M10 Aircraft Nut (#106). Make sure the ball stopper on
the Cable is underneath the Upper Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of
Upper Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 1/8” Allen Bolt
(#94), two Ø 1 1/8” Bushings (#86), and one M10 Aircraft Nut (#106).
C.) Draw the Cable around the Pulley then downward. Install a Pulley to the top holes on
the two Double Floating Pulley Brackets (#46). Secure the Pulley with one M10 x 1 ¾”
Allen Bolt (#93), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#106). Let the
Brackets hanging for now.
D.) Draw the Cable around the Pulley then upward to the opening on the top of Weight
Glide Post (#34). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#95), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#106).
E.) Draw the Cable around the Pulley then downward to the Sliding Weight Post (#45).
Secure the Cable to the Sliding Weight Post with one M10 x 1” Allen Bolt (#92), two Ø
¾” Washers (#89), and one M10 Aircraft Nut (#106).
F.) Connect the Lat Bar (#50) to the Cable with a Chain (#87) using two C-clips (#84).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 79” Butterfly Cable (#61) to the clip on the Left Butterfly (#40). Draw the
Cable to the left Butterfly Pulley Bracket (#44).
B.) Attach a Pulley (#81) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#93), two ∅ ¾”
Washers (#89), and one M10 Aircraft Nut (#106).
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley
Bracket (#47). Install a Pulley to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#93),
two ∅ ¾” Washers (#89), and one M10 Aircraft Nut (#106). Let the Bracket hanging for now.
D.) Draw the Cable around the Pulley then upward to the right Butterfly Pulley Bracket. Install
another Pulley. Draw the Cable around the Pulley then clip to the Right Butterfly (#41).
DIRGARM 6
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach one 124” Cable (#60) to the lower opening on the Rear Vertical Beam (#38). Attach
a Pulley to the opening. Secure it with M10 x 2 3/8” Allen Bolt (#95), two Ø 1” Bushings
(#85), and one M10 Aircraft Nut (#106).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post (#34).
Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#93), two ∅ ¾”
Washers (#89), and one M10 Aircraft Nut (#106).
C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket
previously installed in Step-5. Install a Pulley.
D.) Draw the Cable around the Pulley then downward to the open bracket on the back of Rear
Vertical Beam. Install a Pulley then draw the Cable upward to the Single Floating Pulley
Bracket (#47) installed in Step-6. Secure the end of the Cable to the bracket with one M10
x 1” Allen Bolt (#92), two ∅ ¾” Washers (#89), and one M10 Aircraft Nut (#106).
E.) Connect the Shiver Bar (#51) to the Cable with a Chain (#87) using two C-clips (#84).
F.) Check the tension of the Cables. If the Cables are too loose, adjust the tension by moving
up the Pulley on the Double Floating Pulley Bracket (#46). If the Tension is too tight, then
move down the Pulley.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach the Front Post (#3) to the Front Stabilizer (#17).
B.) Secure it with three M10 x 5/8” Allen Bolts (#90) and ∅ ¾” Washers (#89).
DIAGRAM 8
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the Main Seat Support (#1) to the Rear Stabilizer (#4). Secure it with two M10 x
2 3/8” Carriage Bolts (#100), one 5 1/8” x 2 3/8” Bracket (#21), two Ø ¾” Washers
(#89), and two M10 Aircraft Nuts (#106).
B.) Attach the Wheel (#14) to the Rear Stabilizer. Secure it with one M8 x 5 1/8” Allen Bolt
(#98), two Ø5/8” Washers (#88), and one M8 Aircraft Nut (#109).
C.) Place the Main Seat Support (#1) onto the Front Post (#3). Secure it with two M10 x 2
¾” Carriage Bolts (#103), one 5 1/8” x 2 ¾” Bracket (#22), two Ø ¾” Washers (#89),
and two M10 Aircraft Nuts (#106).
DIAGRAM 9
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-10 (See Diagram 10)
A.) Attach the Leg Developer Holder (#2) to the Main Seat Support (#1). Secure it with one
M10 x 5/8” Allen Bolt (#90) and Ø ¾” Washer (#89) from the top, two M10 x 3 ¾” Carriage
Bolts (#101), two Ø ¾” Washers (#89), and two M10 Aircraft Nuts (#106) from the side.
B.) Attach the Leg Developer (#12) to the Leg Developer Holder (#2). Secure it with one Axle
(#18), two M10 x 5/8” Allen Bolts (#90), and two ∅ ¾” Washers (#89).
C.) Attach an Olympic Sleeve (#62) onto the weight post on Leg Developer. Attach a Spring
Clip (#83) to the Sleeve.
D.) Insert the Arm Curl Stand (#6) into the top opening on the Leg Developer Holder. Use a
Lock Knob (#79) to secure the Stand at desired height.
DIAGRAM 10
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-11 (See Diagram 11)
A.) Insert two ؽ” Bushings (#113) into the holes on the Seat Bracket (#5) and align the
holes to the pivot on the Main Seat Support (#1).
B.) Attach the two Backrest Supports (#10) to the Seat Bracket and align the holes. Secure
them with a M10 x 7 ¼” Allen Bolt (#97), two Ø ¾” Washers (#89), and one M10 Aircraft
Nut (#106). Do not over tighten the Nut and Bolt. Make sure the Backrest Supports are
able to swivel.
C.) Attach the Backrest Incline Support (#7) to the opening on the Main Seat Support (#1).
Use the T-shaped Locked Pin (#15) to secure the Backrest Incline Support at “the last
hole”. See diagram below.
D.) Attach the other end of the Backrest Incline Support to the Backrest Supports (#10).
Align the holes and secure them with two M10 x 1 ¾” Allen Bolts (#93) and Ø ¾”
Washers (#89).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-12 (See Diagram 12)
A.) Place the Seat Pad (#8) onto the Seat Bracket (#5). Secure it with four M8 x 1 5/8” Allen
Bolts (#99) and Ø5/8” Washers (#88).
B.) Attach the Bench Backrest Board (#9) to the Backrest Supports (#10). Secure it with four M8
x 1 5/8” Allen Bolts (#99) and Ø5/8” Washers (#88).
C.) Attach the Arm Curl Pad (#11) to the Arm Curl Stand (#6). Secure it with two M8 x 5/8” Allen
Bolts (#91) and Ø 5/8” Washers (#88).
DIAGRAM 12
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-13 (See Diagram 13)
A.) Insert three Foam Tubes (#16) halfway through the holes on Leg Developer Holder (#2) and
Leg Developer (#12).
B.) Push six Foam Rolls (#23) onto the Tubes from both ends.
C.) Push six Foam Roll End Caps (#72) into the ends.
D.) Attach the Arm Curl Handle (#19) to the bracket on the Leg Developer and secure it with a
Lock Pin (#20). Remove the Arm Curl Handle when doing Leg Developer exercises.
DIAGRAM 13
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE EXPLODED DIAGRAM
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
3
1
1
1
1
1
1
6
2
2
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
4
1
1
1
2
1
1
1
1
1
2
2
1
2
2
3
2
1
2
3
4
5
6
7
8
9
Main Seat Support
Leg Developer Holder
Front Post
Rear Stabilizer
Seat Bracket
Arm Curl Stand
Backrest Incline Support
Seat Pad
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
1 5/8” x ¾” End Cap
124” Cable
79” Butterfly Cable
Olympic Sleeve
Long Olympic Sleeve
Ø 1 1/8” Bushing
∅ 1 ½” x 1” Bushing
1 ½” Square End Cap
1 ¾” Square End Cap
2” Square End Cap
1 5/8” x 2 3/8” End Cap
∅ 2” End Cap
∅ 1” Cone-shaped End Cap
Foam Roll End Cap
6” Grip
2 3/8” x 1 ¾” Sleeve
1” Square End Cap
Ø 1” End Cap
1 ¾” x 1 ½” Sleeve
1 ½” x 1” Sleeve
Lock Knob
2
2
1
7
2
4
2
2
3
2
1
4
7
6
6
1
4
7
2
8
1
2
11
1
9
4
2
4
2
14
71
6
2
12
9
2
4
2
1
1
8
4
2
7
12
2
1
43
2
2
1
4
1
1
2
2
1
8
2
1
Bench Backrest Board
10 Backrest Support
11 Arm Curl Pad
12 Leg Developer
13 Ø 2” Leg Developer Bushing
14 Wheel
15 T-shaped Lock Pin
16 Foam Tube
17 Front Stabilizer
18 Axle
19 Arm Curl Handle
20 Lock Pin
21 5 1/8” x 2 3/8” Bracket
22 5 1/8” x 2 ¾” Bracket
23 Foam Roll
Lock Ring
Pulley
1 ¾” x 1 5/8” Rubber Bumper
Spring Clip
C-clip
24 Front Vertical Beam
25 Panel
26 Left Base Frame
27 Right Base Frame
28 Left Bar Holder
29 Right Bar Holder
30 Left Safety Catch
31 Right Safety Catch
32 Safety Stop Frame
33 Backrest Board
34 Weight Glide Post
35 Guide Rod
36 Cross Brace
37 Upper Frame
38 Rear Vertical Beam
39 Butterfly Base
40 Left Butterfly
∅ 1” Bushing
∅ 1 1/8” Bushing
Chain
Ø 5/8” Washer
Ø ¾” Washer
M10 x 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 7 ¼” Allen Bolt
M8 x 5 1/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 3 ¾” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M8 x 2 3/8” Allen Bolt
M6 x 5/8” Philips Screw
M10 Aircraft Nut
M6 x 1 ¼” Allen Bolt
M6 Aircraft Nut
M8 Aircraft Nut
M8 x 3/8” Allen Bolt
Ankle Strap
Single Handle
Ø ½” Bushing
Ø 1” x 3/8” Bushing
Foot Plate
Panel Screw
#6 Allen Wrench (Tool)
#5 Allen Wrench (Tool)
41 Right Butterfly
42 Weight Post
43 Front Top Beam
44 Butterfly Pulley Bracket
45 Sliding Weight Post
46 Double Floating Pulley Bracket
47 Single Floating Pulley Bracket
48 Weight Lifting Sleeve
49 Weight Bar
50 Lat Bar
51 Shiver Bar
52 Lower Safety Stop Frame
53 Safety Hook
54 Shiver Bar Tube
55 4” x 2” Bracket
56 4 3/8” x 1 ¾” Bracket
57 4 ¾” x 2” Bracket
58 Butterfly Arm Pad
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX®
LIMITED WARRANTY
®
IMPEX warrants this product to be free from defects in workmanship and material, under normal use and
service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends
only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at
IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Hans Grohe Plumbing Product 06460000 User Manual
Harbor Freight Tools Cordless Drill 32940 User Manual
Harman Kardon TV Video Accessories 376 User Manual
Hearth and Home Technologies Indoor Fireplace 6000G User Manual
Honeywell Scanner 800 Series User Manual
Hotpoint Refrigerator FFQ48 User Manual
HP Hewlett Packard Projector Ep9012 User Manual
IBM Printer 1 Port USB Print Server User Manual
Image Home Gym IMEX35080 User Manual
i Tech Dynamic Headphones iLady User Manual