NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
IGS 16
PERSONAL TRAINER
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
IGS 16
Retain This
Manual for
Reference
09-22-03
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Place the Main Base Frame (#2) on a flat surface.
B.) Attach two Pulleys (#84) to the open oblique pulley brackets on the center of the Main Base
Frame. Secure each Pulley with one M10 x 2” Allen Bolt (#102), two Ø ¾” Washers (#118),
and one M10 Aircraft Nut (#125).
C.) Attach four Pulleys (#84) to the other four open brackets on the Main Base Frame. Secure
each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one M10
Aircraft Nut (#125).
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Main Base Frame (#2) and the Rear Base (#18) to the bottom of the Rear Vertical
Beam (#4). Align the holes and secure them together with two M10 x 3” Carriage Bolts (#105),
Ø ¾” Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the nuts and bolts yet.
B.) Attach two Pulleys (#84) to the top & bottom open brackets on the Rear Vertical Beam (#4).
Secure each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one
M10 Aircraft Nut (#125).
C.) Push two Stabilizer End Caps (#86) onto each end of the base on the Rear Vertical Beam. After
completing the entire assembling of the machine, check the stability. If the base was not
leveled, adjust the M10 x 1” Socket Cap Screws (#109) on the Caps to level the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Front Vertical Beam (#3) to the Main Base Frame (#2). Secure it with one M10 x 2 ¾”
Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten the
nut and bolt yet.
B.) Attach a Pulley to the bracket on the upper Front Vertical Beam. Attach a L-shaped Bracket
(#28) to the Pulley. Secure them with one M10 x 2” Allen Bolt (#102), two Ø ¾” Washers (#118),
and one M10 Aircraft Nut (#125).
C.) Place two Pulleys in the two openings on the Front Vertical Beam. Secure each Pulley with one
M10 x 2 ½” Allen Bolt (#103), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
D.) Insert a Pulley Pre-tensioner (#24) through the hole on the back of Front Vertical Beam. Secure
it with two Ø 1 1/8” x Ø ½” Washers (#120) and M12 Regular Nuts (#127).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Seat Support (#11) to the Front Vertical Beam (#3) and Main Base Frame (#2).
Secure it to the Front Vertical Beam with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers
(#118), and one M10 Aircraft Nut (#125). Secure it to the Main Base Frame with one M10 x 4 ½”
Allen Bolt (#108), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
B.) Attach the Leg Developer (#12) to the Seat Support. Align the holes and insert a 2 ¾” Leg
Developer Axle (#43). Secure the Axle with two M6 x 3/8” Socket Set Screws (#112). Insert a 4”
L-shaped Pin (#39) to lock the Leg Developer in place. Remove the Pin when doing Leg
Developer exercises.
C.) Insert a Foam Tube (#37) halfway through the hole on the Leg Developer. Push two Foam Rolls
(#62) onto the Tube from both ends. Push two Foam Roll End Caps (#90) into the ends.
D.) Attach a Pulley to the open bracket on the Leg Developer. Secure it with one M10 x 1 ¾” Allen
Bolt (#101), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Insert a M6 x 1 5/8”
Allen Bolt (#96) through the holes on the bracket and secure it with two Ø ½” Washers (#117)
and one M6 Aircraft Nut (#123).
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Place the Seat (#61) onto the Seat Incline Adjustment (#13). Secure it with two M10 x 1 ¾” Allen
Bolts (#101) and Ø ¾” Washers (#118).
B.) Insert the Seat Incline Adjustment into the opening on the Seat Support (#11). Use a Lock Knob
(#71) to secure the Seat at desired height.
C.) Insert a Foam Tube (#37) halfway through the hole on the Seat Incline Adjustment (#13). Push
two Foam Rolls (#62) onto the Tube from both ends. Push two Foam Roll End Caps (#90) into
the ends.
D.) Secure the Tube with one M6 x ¼” Socket Set Screw (#111).
E.) Attach the Front Stabilizer (#14) to the front opening on the Main Base Frame (#2). Secure it
with three M10 x ¾” Allen Bolts (#97) and Ø ¾” Washers (#118).
F.) Attach the Foot Plate (#31) to the Front Stabilizer. Secure it with two M10 x 1” Allen Bolts (#98),
Ø ¾” Spring Washers (#115), Ø ¾” Washers (#118), and Ø ½” Bushings (#46).
G.)Push two Stabilizer End Caps (#86) onto the Front Stabilizer (#14).
DIAGRAM 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP6 (See Diagram 6)
A.) Slide the Sliding Pulley Frame (#21) onto the Sliding Pulley Vertical Beam (#9) from the bottom.
Use a Lock Knob (#71) to secure the Frame at desired position.
B.) Attach the Sliding Pulley Vertical Beam (#9) onto the Rear Base (#18). Secure it with two M10 x
¾” Allen Bolts (#97) and Ø ¾” Washers (#118). Do not tighten the bolts yet.
C.) Place the Upper Frame (#5) onto the Front Vertical Beam (#3). Secure it with two M10 x 4”
Carriage Bolts (#107), Ø ¾” Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the
nuts and bolts yet.
D.) Attach the Upper Frame (#5) to the Rear Vertical Frame (#4). Align them to the Sliding Pulley
Vertical Beam (#9). Secure them together with two M10 x 3” Carriage Bolts (#105), Ø ¾”
Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the nuts and bolts yet.
E.) Insert the axle on the Sliding Pulley Bracket (#22) into the pivot on the Sliding Pulley Frame
(#21). Secure it with one Ø 1 ¼” x Ø 5/8” Washer (#121) and M16 Regular Nut (#128). Make
sure the Bracket is able to swivel.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Attach a Pulley to the front opening on the Upper Frame (#5). Secure it with one M10 x 2 ½”
Allen Bolt (#103), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten
the nut and bolt yet. The Pulley needs to be removed to install the cable later.
B.) Attach the Lat Bar Holder (#19) to the Upper Frame. Secure it with one M10 x 2 ¾” Allen Bolt
(#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
C.) Attach two Pulleys to the open bracket underneath the Upper Frame. Secure them with one
M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
Repeat the same step to install the other two Pulleys to the other open bracket underneath the
Upper Frame.
D.) Attach a Pulley to the opening on the Upper Frame and top of Sliding Pulley Vertical Beam (#9).
Secure each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one
M10 Aircraft Nut (#125).
E.) Thread a Pulley Pre-tensioner (#24) into the hole underneath the Upper Frame and secure it
with one M12 Regular Nut (#127) and Ø1 1/8”xØ ½” Washer (#120). Do not tighten the nut yet.
F.) Attach a Pulley to the Adjustable Single Pulley Bracket (#25). Secure it with one M10 x 1 ¾”
Allen Bolt (#101), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
G.) Insert the Adjustable Single Pulley Bracket (#25) through the hole on the Upper Frame. Secure
it with two Ø 1 1/8” x Ø ½” Washers (#120), one M12 Regular Nut (#127) and one M12 Aircraft
Nut (#126). Do not tighten the nuts yet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Insert the Right Butterfly Arm (#6) into the pivot on the Front Vertical Beam (#3). Secure it
with one M10 x ¾” Allen Bolt (#97), Ø ¾” Spring Washer (#115), and Ø 1 ½” x Ø ½”
Washer (#122).
B.) Insert the Butterfly Swivel Handle (#8) into the pivot tube on the Right Butterfly Arm (#6).
Secure the bottom with a Ø 1” Clip Ring (#94).
C.) Repeat the above steps to install the other side.
DIAGRAM 8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the Bench Press Base (#32) to the pivot on the Upper Frame (#5). Align the holes and
insert a 8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x ½”
Socket Set Screws (#113).
B.) Attach the Bench Press Arm (#1) to the Bench Press Base (#32). Align the holes and insert a
8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x ½” Socket Set
Screws (#113).
C.) Thread a T-shaped Pull Pin Set (#69) through the hole on the Bench Press Base (#32) to obtain
the desired Bench Press position.
D.) Attach two Pulleys (#84) to the open bracket on the back of Bench Press Base (#32). Secure
them with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft
Nut (#125).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Diagram 10)
A.) Attach the Backrest Adjustment Frame (#10) to the Front Vertical Beam (#3). Secure the
bottom of the Frame to the Front Vertical Beam with one M10 x 3 1/8” Allen Bolt (#106), two Ø
¾” Washers (#118), and one M10 Aircraft Nut (#125).
B.) Attach two Backrest Swivel Brackets (#38) to the pivot on the Frame. Attach the Backrest Board
(#60) to the Brackets. Secure the Board with two M10 x 1 1/8” Allen Bolts (#99) and Ø ¾”
Washers (#118).
C.) Thread a T-shaped Pull Pin Set (#69) through the hole on the Front Vertical Beam (#3) to obtain
the desired Backrest position.
D.) Attach the Angled Foam Tube (#30) to the Backrest Adjustment Frame (#10). Secure it with
one Bent Bracket (#29), M10 x 1 5/8” Allen Bolt (#100) and Ø 7/8” Bent Washer (#119).
E.) Push two Foam Rolls (#62) onto the Tube from both ends. Push two Foam Roll End Caps
(#90) into the ends.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Diagram 11)
A.) Align two Ø 2 ½” x 1” Rubber Bumpers (#76) onto the holes on the Main Base Frame (#2).
Insert two Guide Rods (#15) through the Bumpers and into the Base Frame. Slide 19 Weight
Plates (#48) onto the Guide Rods.
B.) Slide the Selector Stem (#47) with the Selector Rod (#36) onto the Guide Rods. Insert the
Selector Rod (#36) through the center hole.
C.) Insert a Weight Plate Selector Pin (#72) through the selected hole on the Weight Plates.
D.) Place the Top Socket Assembly (#20) onto the Guide Rods. Secure it to the Upper Frame (#5)
with two M10 x 2 ¾” Allen Bolts (#104), four Ø ¾” Washers (#118), and two M10 Aircraft Nuts
(#125).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12 (See Diagram 12)
A.) Attach two Pulleys to each Angled Double Floating Pulley Bracket (#26). Secure each Pulley
with one M10 x 1 ¾” Allen Bolt (#101), two ∅3/4” Washers (#118), and one M10 Aircraft Nut
(#125). Do not tighten the nuts and bolts yet. The Pulleys may need to be removed when
installing the Cables.
B.) Attach one Pulley to a Single Pulley Bracket (#23).
C.) Attach two Pulleys to the Double Floating Pulley Brackets (#27).
DIAGRAM 12
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13 Upper Cable Looping (See Diagram 13)
A.) Slide a Ball Stopper (#70) onto the 161” Upper Cable (#52). Slide and Pull the Cable Strap
Bracket (#45) onto the Cable. Secure the Bracket with a M8 x 1 ¼” Allen Bolt (#110) and M8
Aircraft Nut (#124).
B.) Attach the tip of the Upper Cable to the Pulley on the front of the Upper Frame (#5). Insert
the Cable into the Frame through the tube to the second opening. Remove the Pulley to get
the Cable out then reinstall the Pulley.
C.) Draw the Cable around the Pulley then down to the right Pulley on the back of the Bench
Press Base (#32). Draw the Cable around the right Pulley then to the Pulley on the front of
the Front Vertical Beam (#3).
D.) Draw the Cable around the Pulley then back to the left Pulley on the back of the Bench Press
Base (#32).
E.) Draw the Cable around the left Pulley then to the Pulley in the upper open slot on the Front
Vertical Beam (#3).
F.) Draw the Cable underneath the Pulley then pull upward to the first right Pulley underneath
the Upper Frame. Draw the Cable over the Pulley to the second right Pulley underneath the
Upper Frame.
G.)Draw the Cable over the Pulley then pull downward. Attach the Cable to the upper Pulley on
an Angled Double Floating Pulley Bracket (#26) installed in Step12. Attach the Bracket
underneath the Pulley Pre-tensioner (#24).
H.) Draw the Cable underneath the Pulley then pull upward to the Pulley on the Adjustable
Single Pulley Bracket installed in Step-7G. Let the Double Floating Pulley Bracket (#26)
hanging for now.
I.) Draw the Cable around the Pulley then pull downward to the Selector Rod (#36).
J.) Attach the end of the Cable to a M12 x 1” Split Bolt (#42). Thread the Split Bolt through a Ø
1” Spring Washer (#116) and the ring on the Weight Plate Selector Pin (#72) into the
Selector Rod (#36).
K.) Connect the Lat Bar (#17) to the Cable Strap Bracket with a Hook (#41).
L.) Place the Lat Bar onto the Lat Bar Holder.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 13
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 14 High-Low Station Cable Looping (See Diagram 14)
A.) Slide a Ball Stopper (#70) onto the 262” High-Low Cable (#53). Slide and Pull the Cable
Strap Bracket (#45) onto the Cable. Secure the Bracket with a M8 x 1 ¼” Allen Bolt (#110)
and M8 Aircraft Nut (#124).
B.) Attach the Cable in between the pre-assembled two Small Pulleys (#85) on the
Sliding Pulley Frame (#22). Note: The Ball Stopper should be in front of the Sliding
Pulley Frame.
C.) Draw the Cable through the Sliding Pulley Frame then pull upward to the Pulley on
the top opening of the Sliding Pulley Vertical Beam (#9).
D.) Draw the Cable over the Pulley then pull forward to the Pulley on the rear opening on
the Upper Frame (#5).
E.) Draw the Cable over the Pulley then pull downward. Attach the Cable to the Pulley
on the Single Floating Pulley Bracket (#23) installed in Step12.
F.) Draw the Cable underneath the Pulley then pull upward to the Pulley on the upper
Rear Vertical Frame (#4). Let the Single Floating Pulley Bracket hanging for now.
G.) Draw the Cable around the Pulley then drop the Cable inside the tube downward
through the Rear Vertical Frame to the Pulley on the bottom opening. Remove the
Pulley to get the Cable out then reinstall the Pulley. Draw the Cable underneath the
Pulley then pull upward to the bracket on the Sliding Pulley Frame (#21).
H.) Attach the Cable head to the bracket. Secure the Cable head in place with one M10
x 1 1/8” Allen Bolt (#99) and M10 Aircraft Nut (#125).
I.) Connect the Single Handle (#35) to the Cable Strap Bracket (#45) with a Hook (#41).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 14
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 15 Lower & AB Cable Looping (See Diagram 15)
A.) Insert the 265” Lower Cable underneath the Pulley on the Leg Developer (#12).
B.) Draw the Cable underneath the Pulley along the Main Base Frame to the Pulley under the
Seat. Continue drawing the Cable along the Base Frame through the opening on the bottom
of the Front Vertical Beam to the Pulley on the rear of Main Base Frame.
C.) Draw the Cable underneath the Pulley then pull upward to the left Pulley underneath the
Upper Frame (#5). Draw the Cable around the Pulley then pull downward. Attach the Cable
to the upper Pulley on the Double Floating Pulley Brackets (#27) previously installed in Step-
12.
D.) Draw the Cable around the Pulley then upward to the left Pulley under the Upper Frame. Let
the Bracket hanging for now.
E.) Draw the Cable around the Pulley then downward. Attach the Cable to the upper Pulley on
an Angled Double Floating Pulley Bracket (#26) previously installed in Step-12.
F.) Draw the Cable underneath the Pulley then upward to the Pulley in the middle opening on
the Front Vertical Beam. Draw the Cable over the Pulley and through the opening.
G.)Install the Ball Stopper (#70) and the Cable Strap Bracket (#45) to the Cable. Connect a
Hook (#41) to the Cable Strap Bracket and secure with the M8 x 1 ¼” Allen Bolt (#110) and
M8 Aircraft Nut (#124) on the Bracket.
H.) Connect the AB Strap (#58) or Triceps Rope (#59) to the Hook for various exercises.
I.) Use a Hook (#41) to connect a Chain (#40) to the clip on the end of the Cable in front of the
Leg Developer (#12).
J.) Use a Hook (#41) to connect the Ankle Strap (#57), Double Handle (#34), or Shiver Bar (#33)
to the Chain for various exercises.
K.) Note: After completing the entire Cable installations, adjust the tightness of the Cable Loop
System by adjusting the height of the Pulley Pre-tensioner (#24). Lower the Pre-tensioner so
it touches the top of the Pulley Bracket.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 15
24
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 16 Butterfly Cable Looping (See Diagram 16)
A.) Attach one end of the 99” Butterfly Cable (#55) to the bottom of the Right Butterfly (#6).
Secure it with the M10 x 1 5/8” Allen Bolt (#100), Ø 7/8” x ½” Spacer (#80), two Ø ¾”
Washers (#118), and one M10 Aircraft Nut (#125) on the Bracket.
B.) Remove the Cable Strap Bracket from the other end of the Cable.
C.) Pull the Cable towards the back of the machine to the right oblique Pulley on the Main Base
Frame behind the Front Vertical Beam.
D.) Draw the Cable underneath the Pulley then pull upward to the lower Pulley on the Angled
Double Floating Pulley Bracket (#26). Draw the Cable around the Pulley then downward to
the left oblique Pulley on the Main Base Frame.
E.) Draw the Cable underneath the Pulley then pull to the Left Butterfly (#7).
F.) Repeat the Step A above to secure the end Cable to the Left Butterfly.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 17 Tension Cable looping (See Diagram 17)
A.) Thread the bolt on the 161” Tension Cable (#56) into the Single Floating Pulley Bracket (#23)
previously installed.
B.) Remove the Cable Strap Bracket from the other end of the Cable.
C.) Draw the Cable down to the oblique Pulley on the Main Base Frame. Draw the Cable
underneath the Pulley then pull upward to the lower Pulley on the Angled Double Floating
Pulley Bracket (#26) previously installed.
D.) Draw the Cable around the Pulley then pull downward to the other oblique Pulley on the Main
Base Frame.
E.) Draw the Cable underneath the Pulley then pull upward to the lower Pulley on the Double
Floating Pulley Bracket (#27) previously installed.
F.) Draw the Cable over the Pulley then pull downward to the post on the Main Base Frame.
Attach the end of the Cable to the Cable Strap Bracket (#45). Secure the Strap to the post
with one M8 x 1 ¼” Allen Bolt (#110) and M8 Aircraft Nut (#124).
G.) Securely tighten all Nuts and Bolts previously installed.
H.) Check the tightness of the Cable Loop System.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 18 (See Diagram 18)
A.) Attach two Weight Plate Covers (#16) to the Top Socket Assembly (#20) and Main Base
Frame (#2). Secure each Weight Plate Cover with four M6 x 3/8” Allen Bolts (#95) and Ø ¾”
Nylon Washers (# 67).
DIAGRAM 18
27
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
56
57
58
59
60
61
62
63
64
65
66
67
68
161” Tension Cable
Ankle Strap
AB Strap
Tricep Rope
Backrest Board
1
1
1
1
1
1
6
4
38
4
2
8
8
2
3
2
1
4
1
2
2
2
KEY NO. DESCRIPTION
Q’ty
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
2
2
1
1
5
1
1
2
6
2
1
19
8
2
2
1
1
1
1
1
2
3
4
Bench Press Arm
Main Base Frame
Front Vertical Beam
Rear Vertical Beam
Upper Frame
Seat
Foam Roll
5
6
Right Butterfly
Butterfly Handle Bushing
Weight Plate Bushing
Selector Stem Bushing
Ø 5/8” Bushing
Ø ¾” Nylon Washer
Sliding Frame Plastic Cap
T-shaped Pull Pin Set
Ball Stopper
7
Left Butterfly
8
9
Butterfly Swivel Handle
Sliding Pulley Vertical Beam
Backrest Adjustment Frame
Seat Support
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Leg Developer
Seat Incline Adjustment
Front Stabilizer
Guide Rod
Weight Stack Cover
Lat Bar
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Lock Knob
Weight Plate Selector Pin
Weight Cover Rubber Edge
Rubber Pad
Foot Plate Anti-slipping Pad
Ø 2 ½” x 1” Rubber Bumper
Ø 1” x 5/8” Rubber Bumper
Rear Base
Lat Bar Holder
Top Socket Assembly
Sliding Pulley Frame
Sliding Pulley Bracket
Single Floating Pulley Bracket
Pulley Pre-tensioner
Adjustable Single Pulley Bracket
Angled Double Floating Pulley Bracket
Double Floating Pulley Bracket
L-shaped Pulley Bracket
Bent Bracket
Angled Foam Tube
Foot Plate
Bench Press Base
Shiver Bar
Double Handle
Single Handle
Backrest Board Rubber Bumper 1
Ø 1” x 3” Rubber Bumper
Ø 7/8” x ½” Spacer
Bench Press Handle Grip
Sliding Frame Handle Grip
Butterfly Grip
2
2
4
1
4
30
2
4
11
1
1
6
2
8
1
2
8
3
7
2
4
3
20
3
5
8
4
1
2
1
4
4
Pulley
Small Pulley
85
86
Stabilizer End Cap
2” Square End Cap
1 ½” Square End Cap
2” x 1” End Cap
Foam Roll End Cap
Ø 2 3/8” End Cap
Ø 1” End Cap
2 3/8” Pin
Ø 1” Clip Ring
M6 x 3/8” Allen Bolt
M6 x 1 5/8” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 1/8” Allen Bolt
M10 x 1 5/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 3” Carriage Bolt
M10 x 3 1/8” Allen Bolt
M10 x 4” Carriage Bolt
M10 x 4 ½” Allen Bolt
M10 x 1” Socket Cap Screw
M8 x 1 ¼” Allen Bolt
87
88
89
90
91
92
93
94
95
96
97
Selector Rod
Foam Tube
Backrest Swivel Bracket
4” L-shaped Pin
Chain
Hook
98
M12 x 1” Split Bolt
2 ¾” Leg Developer Axle
8” Bench Press Axle
Cable Strap Bracket
Ø ½” Bushing
Selector Stem
Weight Plate
Ø 1 ¼” Bushing
Ø ¾” Bushing
99
100
101
102
103
104
105
106
107
108
109
110
Ø 1” Bushing
161” Upper Cable
262” High Low Cable
265” Lower & AB Cable
99” Butterfly Cable
29
Download from Www.Somanuals.com. All Manuals Search And Download.
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
M6 x ¼” Socket Set Screw
M6 x 3/8” Socket Set Screw
M10 x ½” Socket Set Screw
M10 x ¾” Socket Set Screw
Ø ¾” Spring Washer
Ø 1” Spring Washer
Ø ½” Washer
1
2
4
2
4
1
6
93
1
5
1
2
3
4
45
1
5
1
1
1
1
1
1
Ø ¾” Washer
Ø 7/8” Bent Washer
Ø 1 1/8” x Ø ½” Washer
Ø 1 ¼” x Ø 5/8” Washer
Ø 1 ½” x Ø ½” Washer
M6 Aircraft Nut
M8 Aircraft Nut
M10 Aircraft Nut
M12 Aircraft Nut
M12 Regular Nut
M16 Regular Nut
Allen Wrench #8 (Tool)
Allen Wrench #6 (Tool)
Allen Wrench #5 (Tool)
Allen Wrench #4 (Tool)
Allen Wrench #3 (Tool)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
IGS-16 WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station
1
2
3
4
5
6
73
73
70
100
77
31
38
7
84
84
81
115
88
36
44
8
95
95
92
130
99
41
50
9
Arm Curl
Lat Pull
18
18
15
25
22
6
29
29
26
40
33
11
14
40
40
37
55
44
16
20
51
51
48
70
55
21
26
62
62
59
85
66
26
32
106
106
103
145
110
46
AB Station
Leg Developer
Bench Press
Butterfly
High Low Cable
8
56
WEIGHT PLATE
Station
10
11
12
13
14
15
16
17
18
19
Arm Curl
117 128 139 150 161 172 183 194 205 216
117 128 139 150 161 172 183 194 205 216
Lat Pull
AB Station
Leg Developer
Bench Press
Butterfly
114 125 136 147 158 169 180 191 202 213
160 175 190 205 220 235 250 265 280 295
121 132 143 154 165 176 187 198 209 220
51
62
56
68
61
74
66
80
71
86
76
92
81
98
86
91
96
High Low Cable
104 110 116
* Numbers are approximate. Actual weights may vary.
* Values for Butterfly are for each arm.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
IRON GRIP SPORT
By IMPEX FITNESS PRODUCTS
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Grizzly Nail Gun H6332 User Manual
Havis Shields Personal Computer C TCB 14 User Manual
Heat Glo LifeStyle Indoor Fireplace ST 42TVFL IPI User Manual
Honeywell Weather Radio T675A User Manual
Hotpoint Electric Pressure Cooker EW31 User Manual
HP Hewlett Packard PDAs Smartphones hx2000 Series User Manual
HP Hewlett Packard Personal Computer 575611 001 User Manual
HP Hewlett Packard Printer 1150 Series User Manual
Humminbird Switch 531871 1_A User Manual
Impex Home Gym WM 357 User Manual