Ikelite Digital Camera SD630 User Manual

Digital Housing  
i n s t r u c t i o n m a n u a l  
f o r  
Canon  
PowerShot S80  
H o u s i n g  
#6140.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IInnssttaalllliinngg tthhee CCaammeerraa  
Remove the back  
CClloossiinngg tthhee HHoouussiinngg  
housing back  
1. Place housing face down in your  
lap or on flat surface.  
See Lens Cover Note below  
from the housing.  
The mounting tray  
2. Check to see that there is an  
o’ring on the housing back and  
that it is clean and in its proper  
location.  
3. Guide the back onto the housing.  
The o’ring should touch the  
housing all the way around. There  
should be an even gap all the way  
around between the housing and  
the housing back.  
4. Lift the lid snaps so they are  
extended and place the lid snap  
into the hook on the housing  
back.  
O' Ring  
for the camera is  
secured to the  
housing back.  
Lid  
Hook  
Position the camera  
on the tray and  
secure it with the  
mounting bolt  
o’ring  
housing  
which threads into  
the camera’s tripod  
socket. Use aa ccooiinn  
or flatt bladed  
screwdrriver too tighteen the mouunting bbolt so tthhe camerra is flat  
against tthe tray.  
Mounting  
Tray  
Mounting Bolt  
CAMERA / MOUNT  
housing back  
5. To close the housing push  
down on the lid snaps until  
they snap into place . Lid  
even gap  
CAUTION:  
all 4 sides  
Some camera tripod socket threads are plastic. The mounting  
tray bolt is metal. Do not cross thread or over tighten as you  
may damage the camera tripod socket threads.  
snaps on opposite sides of the  
housing should be closed at the  
same time. Be sure they are down  
far enough to engage the lock.  
o’ring  
housing  
NNOOTTEE:: TThhee ccaammeerraass LLeennss CCoovveerr mmuusstt bbee iinn tthhee ooppeenn  
ppoossiittiioonn bbeeffoorree cclloossiinngg tthhee hhoouussiinngg..  
Slide the camera’s Lens Cover open, then slide it back towards the  
lens until the camera’s lens retracts back into the camera body.  
Leave the Lens Cover in this position when installing the camera  
into the housing. In this position the housing ON/OFF control can  
be used to turn the camera on and off.  
Double chheck - Once the housing is closed, check the o’ring seal.  
Check the gap between the housing back and the housing, it  
should be even all the way around.  
Look through the clear plastic back at the o’ring. You should see a  
darkened area where the o’ring is compressed against the  
housing back. If you do not see an even black compression seal  
all the way around the back, open the lid snaps, reseat the  
housing back and close the lid snaps. Visually check the seal again.  
4
5
CChheecckkiinngg CCoonnttrroollss  
UUssiinngg tthhee ZZoooomm CCoonnttrrooll UUnnddeerrwwaatteerr  
Once the housing has been closed, push the controls back into  
place. Make sure they line up with the camera’s controls. Pull  
out on the housing’s Zoom Control and align with the camera’s  
Zoom Lever then push the housing control back in to engage  
with the camera’s Zoom lever.  
When the housing’s Zoom control is activated underwater the  
water pressure will not allow the camera’s Zoom lever to return  
to the center position. When the camera’s Zoom lever is held to  
You  
either side it will not allow the camera to take a picture.  
must reeturn thee cameraas Zoom leever to thhe centerr positiion after  
each actiivation.  
TTuurrnniinngg tthhee CCaammeerraa OOnn  
To turn the camera ON, use the housing ON/OFF control to  
slide the Camera Lens Cover away from the lens. To turn the  
camera OFF, pull out on the housing ON/OFF control and  
rotate it past the raised part of the Lens Cover, push down and  
slide the Lens Cover toward the lens (Lens will retract into  
camera body).  
UUssiinngg tthhee RRiigghhtt AArrrrooww//FFllaasshh aanndd MMuullttii CCoonnttrrooll DDiiaall  
The housing’s control for the camera’s Right Arrow/Flash and  
Multi Control Dial has a white dot that aligns with the housing  
controls activation paw. The control is used in two different ways.  
To activate the Right Arrow/Flash function place the white dot  
over the camera control and push in and pull out on the housing  
control.  
LLuubbrriiccaannttss  
1. Ikelite provides silicone lubricant with the housing. We recommend  
you use only Ikelite lubricant on Ikelite products as some other  
brands may cause the o’ring to swell and not seal properly.  
2. Use only enough lubricant to lightly cover control shafts and  
o’rings. Wipe off any excess lubricant with a clean cloth.  
Lubricant is not a sealant, it is used to reduce friction. Excessive  
lubricant can collect sand and dirt which may interfere with  
proper sealing.  
To rotate the camera’s Multi Control Dial place the white dot at  
about an 8 o’clock position, rotate the housing control clockwise  
to about the 10 o’clock position. Lift the housing control and  
repeat this action until the desired setting is obtained.  
CAUTION:  
UUnnddeerrwwaatteerr tthhee wwhhiittee ddoott oonn tthhee ccoonnttrrooll sshhoouulldd bbee ppllaacceedd iinn tthhee  
33 oocclloocckk ppoossiittiioonn ssoo iitt ddooeess nnoott aaccttiivvaattee tthhee ccaammeerraass AArrrrooww//FFllaasshh  
ccoonnttrrooll.. Underwwater thee water prressure wwill pushh this conntrol in.  
If the caamera’ss RRight Arrrow/Flassh controol is heldd in the deepressed  
posittion sevveral ccaamera fuunctionns will nnot acttivate.  
CAUTION  
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann  
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diffuser/Deflector material  
UUssiinngg FFllaasshh  
DDiiffffuusseerr aanndd DDeefflleeccttoorr ccoonntt..  
A diffuser and deflector are  
included with the housing. The  
diffuser is white transparent  
plastic. The deflector is also  
white but is not transparent  
and has a decal on the front.  
UUssiinngg tthhee CCaammeerraass BBuuiilltt--iinn FFllaasshh..  
If you do not have an external flash the camera’s built-in flash  
can be used. See Diffuser instructions.  
Port Clamp  
Spring  
To install the diffuser or  
deflector spread the port clamp  
at the spring end and slide over  
the lens port. The white plastic  
should be placed in front of the  
camera flash. The port clamp  
should be pushed back against  
the front of the housing.  
DDiiffffuusseerr && DDeefflleeccttoorr IInnssttaallllaattiioonn  
Diffuser  
Spread to Install  
DDiiffffuusseerr  
The diffuser should be installed when using the camera’s built in  
flash. When shooting with the camera’s built-in flash at  
approximately 2 feet (0.6 m) or less, the lens port on the  
housing may block a portion of the light from the camera’s  
built-in flash, creating a shadow in the lower left of the photo.  
If this occurs, zoom the lens slightly to eliminate the shadow.  
(You can test this above water)  
DDeefflleeccttoorr  
The deflector should be installed when using an external strobe  
such as the DS51 or DS125 Substrobe and EV Controller. The  
deflector will redirect the camera’s flash to the EV Controller  
which controls the external strobes output.  
Housing shown with  
Diffuser installed.  
8
9
OOppttiioonnaall AAcccceessssoorriieess  
LLeennss PPoorrtt  
Treat the glass in the lens port as a camera lens. After use, rinse  
and gently dry the lens port to avoid water spotting. To clean  
use a mild soap solution or lens cleaner.  
BBaacckk OOrriinngg #0109  
O’rings last for several years if properly maintained. (See  
maintenance) Always carry a spare.  
Do not use alcohol or window cleaner on the Lens Port.  
WWiiddee--AAnnggllee AAddaapptteerr #9306.80  
The Lens Port will accept (2) Wide-Angle Adapters. The Wide-  
Angle Adapter #9306.80 which is required to mount the Inon  
UWL-150AD Bayonet style wide-angle lens. The Wide-Angle  
Adapter 9306.81 is required to mount the following Wide-Angle  
Lenses, Inon UWL-100, Sea&Sea #58070 and Ep0que DCL-20  
screw thread (67mm) style wide-angle lenses.  
These lenses can be secured onto the Wide-Angle Adapter  
above or below water as they are designed to have water  
between the front of the port and the accessory lens. Make sure  
no air bubbles are trapped between the port and the accessory  
lens. Any vignetting that occurs can be eliminated by zooming  
the camera lens slightly. The camera’s built-in flash cannot be  
used with wide angle  
Required to mount Inon UWL-150AD Bayonet style wide-angle  
lens.  
WWiiddee--AAnnggllee AAddaapptteerr #9306.81  
Required to mount Inon UWL-100 Screw Thread (67mm) style  
wide-angle lens.  
UURR//PPrroo FFiilltteerr #6441.32  
The UR/Pro underwater color correcting filter is designed to  
restore some of the warm colors filtered out by the water. For  
available light use only, not recommended for use with flash.  
TTrraayy wwiitthh RReelleeaassee HHaannddllee #9523.31  
Tray and Release Handle is required to mount external  
Substrobes.  
Wide-Angle Adapter  
lenses. The front of the  
lenses are so large they  
block the camera’s flash.  
To properly light subjects  
when using a wide angle  
lens an external strobe  
should be used. Due to  
the wide-angle of  
wide-angle lens  
coverage of these lenses,  
the DS125 Substrobe is  
recommended or two  
DS51 Substrobes.  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Substrobe  
DS125  
OOppttiioonnaall AAcccceessssoorriieess  
OOppttiioonnaall AAcccceessssoorriieess  
Substrobe  
DS51  
SSuubbssttrroobbee DDSS5511 PPaacckkaaggee #3944.57  
The Substrobe DS51 package includes  
the Substrobe DS51, the EV  
SSuubbssttrroobbee DDSS112255 PPaacckkaaggee #3944.77  
The Substrobe DS125 package  
includes the Substrobe DS125, the EV  
Controller, ball socket arm and  
charger. The EV Controller provides  
10 manual power settings in 1/2 stop  
increments. An external strobe offers  
several advantages over using the  
camera’s built-in flash. External  
strobes move the flash away from  
the camera lens which helps reduce  
backscatter. They also expand  
lighting options to achieve the best  
lighting for different subjects. A  
second external digital strobe  
Controller and ball socket arms. The  
EV Controller provides 10 manual  
power settings in 1/2 stop  
increments. An external strobe  
offers several advantages over using  
the camera’s built-in flash. External  
strobes move the flash away from  
the camera lens which helps reduce  
backscatter. They also expand  
lighting options to achieve the best  
lighting for different subjects. A  
second external digital strobe  
package can be added to fill the  
shadows and produce more realistic  
photographs.  
Ball Socket  
Arm  
Ball Socket  
Arm  
package can be added to fill the  
shadows and produce more realistic  
photographs.  
The Substrobe DS51 covers the  
equivalent of a 28mm lens. It is the  
ideal choice when using only the  
camera lens or the camera lens with  
a macro accessory lens.  
The Substrobe DS125 covers the  
equivalent of a 18mm lens, 100  
degrees. It is the ideal choice when  
using accessory wide angle lenses  
greater than 28mm.  
EV Controller  
EV Controller  
If an accessory wide angle lens wider  
than 28mm is used, the ideal  
lighting choice is the Substrobe  
DS125, which covers 100 degrees, or  
two Substrobe DS51’s can be used.  
NOTE:  
NOTE:  
Optional Tray and  
Optional Tray and  
Release Handle  
required to mount  
Substrobes.  
Release Handle  
required to mount  
Substrobes.  
12  
13  
MMaaiinntteennaannccee  
CCoonnttrrooll MMaaiinntteennaannccee  
The Ikelite Digital Housing should be given the same care and  
attention as your other photographic equipment. In addition to  
normal maintenance we recommend that the housing be returned  
to Ikelite periodically to be checked and pressure tested.  
Ikelite controls are designed to provide years of reliable service  
with minimal maintenance.  
1. Push button controls require no maintenance other than rinsing  
in fresh water after saltwater use. If a push button control  
becomes difficult to push or if it sticks when depressed, soak the  
housing in luke warm fresh water. After a few minutes operate  
the push button. If this does not correct the problem, return the  
housing to Ikelite for maintenance.  
Do Not  
1.  
leave the camera and housing in direct sunlight for  
prolonged periods. Heat may damage the camera.  
2. Do Nott ship the camera in the housing.  
3. Before using the housing, always check the tightness of the  
screw in each control knob.  
set  
controol gland  
Check each  
penetrating the housing to make sure  
they are tight. There is a slight chance that either could vibrate  
loose during travel.  
lubricate shaft  
4. Keep the back o’ring clean and lightly lubricated. To lubricate  
remove the o’ring from the back. Put a small amount of lkelite  
lubricant on your fingers. Draw the o’ring through your fingers  
to apply a light coating of lubricant. Only apply enough  
housing  
pull out to  
expose shaft  
Do Not sstretcch the oo’ring  
lubricant to make the o’ring feel slick.  
.
This light coating of lubricant will help to keep the o’ring from  
drying out and will help to show a dark sealing line when the  
housing back is properly sealed.  
2. Some of the controls have long shafts. These controls can be  
pulled out, exposing the shaft (see drawing).  
5. Keep the area where the o’ring fits and the sealing surface of  
the housing clean.  
To lubricate the control, gently pull on the knob until the  
stainless steel shaft is exposed. Lightly lubricate the shaft, then  
move the shaft in and out several times. This will lubricate the  
x’ring in the Ikelite control gland. This should be done before  
using the housing after a prolonged storage period, or once a  
week when the housing is in use.  
6. Rinse the housing exterior thoroughly in fresh water after each  
salt water use. Dry with a soft cloth. Dry lens port to eliminate  
water spotting.  
After several uses in salt water soak the housing exterior in a  
mild soap solution, rinse and dry before storage. When storing  
the housing, remove the back o’ring, lightly lubricate and place  
in a plastic bag. Place the plastic bag with o’ring inside the  
housing for safe keeping.  
CCAAUUTTIIOONN  
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann  
14  
15  
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CCoonnttrrooll MMaaiinntteennaannccee CCoonntt..  
GGeenneerraall TTiippss  
3. Some of the controls have a short shaft and cannot be pulled  
out exposing the shaft for lubrication. In the unlikely event one  
of these controls sticks or becomes difficult to operate you can  
remove the control from the housing and lubricate it, or return  
the housing to Ikelite for maintenance. To remove the control,  
loosen the set screw in the knob (allen wrench required);  
remove the knob. If there is salt or dirt build-up on the exposed  
control shaft, clean the shaft. Open the housing and gently slide  
the control shaft out of the control gland. Clean and lightly  
lubricate the shaft, including the end of the shaft. Slide the  
shaft back into the control gland and gently slide it back and  
forth a few times without fully removing the shaft from the  
gland. Replace the knob, NOTE the flat area on the shaft, the  
set screw in the knob should tighten down against the flat area  
on the control so the knob does not turn on the shaft.  
1. Due to the power required to operate the camera, flash, and  
LCD screen it is a good idea to start each dive with a fresh set of  
batteries.  
2. Some cameras reset their flash to AUTO when the camera is  
turned on. If you prefer another setting be sure to select it.  
3. As soon as you enter the water, take a moment and check the  
housing to see that it is properly sealed.  
4. Next, check to see if there are any bubbles on the face of the  
lens port. If there are, take your finger and remove them. If  
there are bubbles on the lens port they can produce soft focus  
spots in your photographs.  
NOTE  
5. If you are shooting with the camera’s built-in flash and the  
cameras lens is set to the widest angle you may need to zoom  
the lens slightly or a shadow may appear in the lower left  
corner of close-up photographs. The lens port may block some  
of the light. Installing the flash diffuser will help to eliminate  
the shadow. (You can test this above water)  
housing  
gland  
control  
shaft  
To shoot photographs closer than 2 feet (0.6m), you need to  
use an external strobe such as the DS51 or DS125. With an  
external strobe you can position it so nothing blocks the light  
path between the strobe and the subject.  
Loosen set screw  
(allen wrench required)  
Flat  
Tighten set screw down  
against this area when  
replacing the knob.  
Lubricate end of shaft  
before reinserting into  
gland  
17  
16  
PPhhoottoo TTiippss  
PPhhoottoo TTiippss CCoonntt..  
1. The number one rule in underwater photography is eliminate as  
much water between camera and subject as possible. Get as  
close as you can to the subject, then use the zoom. If you are  
using flash, subjects beyond 6 feet (1.8m)will not have much  
color.  
6. When using daylight or flash if your camera consistently over  
or underexposes the image you may want to adjust your  
camera’s exposure compensation settings. Many cameras allow  
you to adjust both available light and flash exposure with an EV  
control in the camera’s menu.  
2. The camera’s built-in flash is very close to the camera lens. The  
flash can light up any suspended particles in the water and they  
can be recorded in your picture. This effect is called backscatter.  
To eliminate as much backscatter as possible, photograph close.  
Photograph in clear water; do not stir up the sand or silty  
bottom. If backscatter becomes a problem in the environment  
you are photographing, an external flash will help eliminate  
much of the backscatter.  
3. Digital cameras have a slight lag time between when you press  
the shutter release button and the camera actually takes the  
picture. Hold the camera steady a second or two after pressing  
the shutter release button.  
7. Many photographers transfer their images to the computer  
where they can fine tune the appearance of the image. Many of  
the image manipulation programs make you think you can  
magically correct any image taken and make a good picture.  
One thing to remember when using image manipulation  
programs, if the image is overexposed much of the color is  
missing. If the color is missing you cannot adjust it. If images  
are slightly underexposed the color is there, it is just dark and  
you can adjust it to some degree. So if you error in exposure it  
is better to have the image slightly underexposed than over  
exposed.  
4. Do not shoot down on subjects as they will quite often blend  
into the background and be difficult to see in the photograph.  
Shoot subjects straight on or shoot up at a slight angle using  
the blue water as a contrasting background.  
5. Underwater flash is used to restore the warmer colors filtered  
out by the water as well as to illuminate the subject. When  
photographing underwater, set the camera to use flash on  
every shot. If the camera’s flash is set to AUTO and the sun is  
behind your subject, the camera may see enough light that it  
does not fire the flash. With the sun behind the subject the  
subject is shaded (dark) and needs flash for a good exposure.  
18  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy  
All Ikelite products are warranted against any manufacturing  
defects for a period of one (1) year from the date of purchase.  
Defective products should be returned prepaid to Ikelite. Ikelite  
will, at its discretion, repair or replace such products, and will  
return to customer prepaid. All other claims, of any nature,  
including but not limited to bulb failure are not covered. Except as  
mentioned above, no other warranty expressed or implied, applies  
to this Ikelite product.  
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee  
Ikelite is most interested in preforming any service to assure that  
all products perform as intended. For repair or service, return  
the product to the address below with your name, address,  
phone number and a brief description of the problem. Evidence  
of purchase date must be provided to obtain warranty service.  
Ikelitte Underrwater SSystems  
50 W 33rdd Street  
Indiannapoliiss, IN 462208 USA  
317-9223-4523  
email: iikelitee@ikeliite.com  
www.ikellite.com  
Digittal 61400.08-0022-0506  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Air Conditioner HW 18L2H User Manual
Harbor Freight Tools Tool Storage 69572 User Manual
Harman DJ Equipment MFXI User Manual
Havis Shields Automobile Parts KR 153X SP KOV User Manual
Hawking Technology Network Card H DS20L User Manual
Hotpoint Range SBS 638 CX S User Manual
Hotpoint Ventilation Hood BH11 User Manual
Hubbell Switch Type AR User Manual
IBM Computer Monitor T541A User Manual
IKEA Wheelchair AA 152981 2 User Manual