650CRT
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
PRODUCT SPECIFICATIONS
•
•
Read and observe the safety rules.
Gasoline Capacity:
3 Quarts
Unleaded Regular
Follow a regular schedule in maintaining, caring for
and using your tiller.
OIL (API-SF/SJ):
(Capacity 20 oz./0.6L)
SAE 30 (Above 40°F)
SAE 5W-30/10W30
(Below 40°F)
•
Follow instructions under“Maintenance”and“Storage”
sections of this Owner’s Manual.
IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL
COMBUSTION ENGINE AND SHOULD NOT BE USED ON
OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-
COVERED OR GRASS COVERED LAND UNLESS THE
ENGINE'S EXHAUST SYSTEM IS EQUIPPED WITH A SPARK
ARRESTER MEETING APPLICABLE LOCAL LAWS (IF ANY).
IFASPARKARRESTERISUSED,ITSHOULDBEMAINTAINED
IN EFFECTIVE WORKING ORDER BY THE OPERATOR.
Spark Plug:
Champion
RC12YC
(Gap: .030"/0.76mm)
CONGRATULATIONS on your purchase of a new tiller. It
has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problems you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS
REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA
PUBLIC RESOURCES CODE). OTHER STATES MAY HAVE
SIMILARLAWS. FEDERALLAWSAPPLYONFEDERALLANDS.
SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT
FOR SPARK ARRESTER.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tiller properly.
Always observe the “SAFETY RULES”.
TABLE OF CONTENTS
SAFETY RULES ..........................................................2
CUSTOMER RESPONSIBILITIES...............................3
PRODUCT SPECIFICATIONS.....................................3
ASSEMBLY...............................................................4-6
OPERATION ...........................................................7-10
MAINTENANCE SCHEDULE ....................................11
MAINTENANCE ...................................................11-13
SERVICE & ADJUSTMENTS ...............................14-17
STORAGE..................................................................18
TROUBLESHOOTING ...............................................19
REPAIR PARTS-TILLER.......................................20-26
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
FRONT
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) Utility knife
(1) Tire pressure gauge
(1) Pair of pliers
LEFT
RIGHT
(1) 9/16" wrench
OPERATOR’S POSITION (See Fig. 1)
When right or left hand is mentioned in this manual, it
means when you are in the operating position (standing
behind tiller handles).
OPERATOR’S
POSITION
FIG. 1
CONTENTS OF HARDWARE PACK
(1) Carriage Bolt
3/8-16 UNC x 1 Grade 5
(1) Center Locknut
3/8-16 UNC
(2) Handle Locks
(1) Handle Lock Lever
(1) Hairpin Clip
(1) Flat Washer 13/32 x 1 x 11 Gauge
(1) Pivot Bolt
3/8-16 UNC Grade 5
Extra Shear Pins & Clips
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
•
Grasp handle assembly. Hold in “up”position. Be sure
handle lock remains in gearcase notch. Slide handle
assembly into position.
UNPACKING CARTON (See Fig. 2)
CAUTION: Be careful of exposed
staples when handling or disposing
of cartoning material.
HANDLE ASSEMBLY
"UP" POSITION
IMPORTANT:
WHEN UNPACKING AND ASSEMBLING
TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES.
TIGHTEN HANDLE LOCK
LEVER TO HOLD
•
While holding handle assembly, cut cable ties securing
handle assembly to top frame and depth stake. Let
handle assembly rest on tiller.
•
•
Remove top frame of carton.
Slowly ease handle assembly up and place on top of
carton.
•
•
Cut down right hand front and right hand rear corners
of carton, lay side carton wall down.
Remove packing material from handle assembly.
LOOSEN HANDLE
LOCK LEVER TO MOVE
FIG. 4
HANDLE
ASSEMBLY
•
Rotatehandleassemblydown.Insertrearcarriagebolt
first, with bolt head on L.H. side of tiller and loosely
assemble locknut (See Fig. 5).
•
•
Insert pivot bolt in front part of plate and tighten.
Cut down remaining corners of carton and lay panels
flat.
•
Lower the handle assembly. Tighten nut on carriage
bolt so handle moves with some resistance. This will
allow for easier adjustment.
•
•
Place flat washer on threaded end of handle lock le-
ver.
Insert handle lock lever through handle base and
gearcase. Screw in handle lock lever just enough to
hold lever in place.
SHIFT ROD
FIG. 2
•
•
Insert second handle lock (with teeth inward) in the
slot of the handle base (just inside of washer).
With handle assembly in lowest position, securely
tighten handle lock lever by rotating clockwise. Leav-
ing handle assembly in lowest position will make it
easier to remove tiller from carton.
INSTALL HANDLE (See Figs. 3, 4, and 5)
•
Insert one handle lock (with teeth facing outward) in
gearcase notch. (Apply grease on smooth side of
handle lock to aid in keeping lock in place until handle
assembly is lowered into position.)
HANDLE
LOCK
VIEWED FROM R.H. SIDE OF TILLER
HANDLE ASSEMBLY
FLAT
WASHER
GEARCASE
SLOT
HANDLE LOCK
LEVER
GEARCASE
NOTCH
HANDLE
LOCK
CARRIAGE
BOLT
PIVOT BOLT
HANDLE
BASE
LOCKNUT
FIG. 3
FIG. 5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
CONNECT SHIFT ROD (See Fig. 7)
ATTACH CLUTCH CABLE (See Fig. 6)
•
•
Insert end of shift rod into hole of shift lever indicator.
Insert hairpin clip through hole of shift rod to secure.
•
Hook end of clutch cable through hole in control bar
bracket.
SHIFT
HAIRPIN
CLIP
CONTROL BAR
BRACKET
SHIFT
ROD
LEVER
INDICATOR
FIG. 7
REMOVE TILLER FROM CRATE
•
•
•
Make sure shift lever indicator is in “N” position (See
Fig. 7)
Tilt tiller forward by lifting handle. Separate cardboard
cover from leveling shield.
Rotate tiller handle to the right and pull tiller out of
carton.
END OF CLUTCH
CABLE
FIG. 6
CHECK TIRE PRESSURE
The tires on your unit were overinflated at the factory for
shipping purposes. Correct and equal tire pressure is
important for best tilling performance.
•
Reduce tire pressure to 20 PSI (1.4 kg/cm2).
HANDLE HEIGHT
•
Handle height may be adjusted to better suit operator.
(See “TO ADJUST HANDLE HEIGHT” in the Service
and Adjustments section of this manual).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOWYOUR TILLER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TILLER.
Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their
meaning.
THROTTLE
CONTROL
SHIFT LEVER
CHOKE CONTROL
SHIFT LEVER INDICATOR
DRIVE
CONTROL
BAR
DEPTH STAKE
LEVELING
SHIELD
RECOIL
OUTER SIDE
SHIELD
STARTER
HANDLE
FIG. 8
MEETS ANSI SAFETY REQUIREMENTS
Our tillers conform to the safety standards of the American National Standards Institute.
CHOKE CONTROL - Used when starting a cold engine.
DEPTH STAKE - Controls depth at which tiller will dig.
DRIVE CONTROL BAR - Used to engage tines.
LEVELING SHIELD - Levels tilled soil.
OUTER SIDE SHIELD - Adjustable to protect small plants
from being buried.
RECOIL STARTER HANDLE - Used to start the engine.
SHIFT LEVER - Used to shift transmission gears.
SHIFT LEVER INDICATOR - Shows which gear the trans-
mission is in.
THROTTLE CONTROL - Controls engine speed.
.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any tiller can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields before starting
your tiller and while tilling. We recommend a wide vision safety mask for over spectacles
or standard safety glasses.
DEPTH STAKE (See Fig. 10)
The depth stake can be raised or lowered to allow you more
versatile tilling and cultivating, or to more easily transport
your tiller.
HOW TO USEYOUR TILLER
Know how to operate all controls before adding fuel and
oil or attempting to start engine.
STOPPING (See Fig. 9)
TINES AND DRIVE
•
Release drive control bar to stop movement.
•
Move shift lever to “N” (neutral) position.
TRANSPORT
POSITION
SHALLOWEST
TILLING (CULTI-
VATING)
ENGINE
•
Move throttle control to “STOP” position.
•
Never use choke to stop engine.
DEEPEST
TILLING
THROTTLE
CONTROL
SHIFT
LEVER
DEPTH
STAKE
DRIVE CONTROL
BAR
“ENGAGED” PO-
SITION
FIG. 10
TILLING (See Fig. 11)
•
Release depth stake pin. Pull the depth stake up for
increased tilling depth. Place depth stake pin in hole
of depth stake to lock in position.
DRIVE CONTROL BAR
“DISENGAGED” POSITION
•
•
Place shift lever indicator in tilling position.
Hold the drive control bar against the handle to start
tilling movement. Tines and wheels will both turn.
Move throttle control to “FAST” position for deep tilling.
To cultivate, throttle control can be set at any desired
speed, depending on how fast or slow you wish to
cultivate.
FIG. 9
TINE OPERATION - WITH WHEEL DRIVE
•
•
Always release drive control bar before moving shift
lever into another position.
•
Tine movement is achieved by moving shift lever to
(
) till position and engaging drive control bar.
IMPORTANT: ALWAYS RELEASE DRIVE CONTROL
BAR BEFORE MOVING SHIFT LEVER INTO ANOTHER
POSITION.
FORWARD
STOPPED
•
-
WHEELS ONLY/TINES
DEPTH STAKE PIN
“RELEASED” POSITION
Releasedrivecontrolbarandmoveshiftleverindicator
to “F” (forward) position. Engage drive control bar and
tiller will move forward.
REVERSE - WHEELS ONLY/TINES STOPPED
•
•
•
•
•
DO NOT STAND DIRECTLY BEHIND TILLER.
Release the drive control bar.
Move throttle control to “SLOW” position.
Move shift lever indicator to “R” (reverse) position.
Hold drive control bar against the handle to start tiller
movement.
“LOCKED”
POSITION
NUT “B”
HARD TO SHIFT GEARS
•
Brieflyengagedrivecontrolbarandreleaseorrocktiller
forward and backward until are able to shift gears.
OUTER
SIDE SHIELD
NUT “A”
FIG. 11
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
•
For cold weather operation you should change oil for
easier starting (See oil viscosity chart in the Mainte-
nance section of this manual).
To change engine oil, see the Maintenance section in
this manual.
TURNING
•
•
•
Release the drive control bar.
Move throttle control to “SLOW” position.
Placeshiftleverindicatorin“F”(forward)position. Tines
will not turn.
•
•
•
Lift handle to raise tines out of ground.
Swing the handle in the opposite direction you wish
to turn, being careful to keep feet and legs away from
tines.
OIL
LEVEL
•
When you have completed your turn-around, release
the drive control bar and lower handle. Place shift
lever in till position and move throttle control to desired
speed. To begin tilling, hold drive control bar against
the handle.
OIL
FILLER
PLUG
OIL DRAIN
PLUG
OUTER SIDE SHIELDS (See Fig. 11)
The back edges of the outer side shields are slotted so
that the shields can be raised for deep tilling and lowered
for shallow tilling to protect small plants from being buried.
Loosen nut “A” in slot and nut “B”. Move shield to desired
position (both sides). Retighten nuts.
FIG. 12
ADD GASOLINE
•
Fill fuel tank. Use fresh, clean, regular unleaded gaso-
line. (Use of leaded gasoline will increase carbon and
lead oxide deposits and reduce valve life.)
TO TRANSPORT
IMPORTANT: WHENOPERATINGIN TEMPERATURESBELOW
32°F (0°C), USE FRESH, CLEAN, WINTER GRADE GASOLINE
TO HELP INSURE GOOD COLD WEATHER STARTING.
CAUTION: Beforeliftingortransporting,
allow tiller engine and muffler to cool.
Disconnect spark plug wire. Drain
gasoline from fuel tank.
WARNING: Experienceindicatesthatalcoholblendedfuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage. To avoid engine problems,
the fuel system should be emptied before storage of
30 days or longer. Drain the gas tank, start the engine
and let it run until the fuel lines and carburetor are empty.
Use fresh fuel next season. See Storage section of this
manual for additional information. Never use engine or
carburetor cleaner products in the fuel tank or permanent
damage may occur.
AROUND THEYARD
•
Release the depth stake pin. Move the depth stake
down to the top hole for transporting the tiller. Place
depth stake pin in hole of depth stake to lock in posi-
tion. This prevents tines from scuffing the ground.
•
•
•
Place shift lever indicator in “F” (forward) position for
transporting.
Hold the drive control bar against the handle to start
tiller movement. Tines will not turn.
CAUTION: Fill to within 1/2 inch of top of fuel tank
to prevent spills and to allow for fuel expansion. If
gasolineisaccidentallyspilled,movemachineaway
from area of spill. Avoid creating any source of igni-
tion until gasoline vapors have disappeared.
Move throttle control to desired speed.
AROUND TOWN
•
•
•
Disconnect spark plug wire.
Drain fuel tank.
Transport in upright position to prevent oil leakage.
Donotoverfill. Wipeoffanyspilledoilorfuel. Donot
store, spill or use gasoline near an open flame.
BEFORE STARTING ENGINE
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT
TO ENTER THE ENGINE WHEN CHECKING OR ADDING
OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN
APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN
FILL FUNNELS.
TO START ENGINE (See Fig. 13)
CAUTION: Keep drive control bar in
“DISENGAGED” position when start-
ing engine.
CHECK ENGINE OIL LEVEL (See Fig.12)
•
•
•
The engine in your unit has been shipped, from the
factory, already filled with SAE 30 summer weight oil.
With engine level, clean area around oil filler plug and
remove plug.
Engineoilshouldbetopointofoverflowingwhenengine
is level. For approximate capacity see “PRODUCT
SPECIFICATIONS” on page 3 of this manual. All oil
must meet A.P.I. Service Classification SF-SJ.
When starting engine for the first time or if engine has run
out of fuel, it will take extra pulls of the recoil starter to
move fuel from the tank to the engine.
•
•
•
•
Make sure spark plug wire is properly connected.
Move shift lever indicator to “N” (neutral) position.
Place throttle control in “FAST” position.
Turn fuel shut-off valve 1/4 turn to open position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
•
Soilconditionsareimportantforpropertilling.Tineswill
•
•
Move choke control to choke position.
notreadilypenetratedry,hardsoilwhichmaycontribute
to excessive bounce and difficult handling of your tiller.
Hard soil should be moistened before tilling; however,
extremely wet soil will “ball-up” or clump during tilling.
Wait until the soil is less wet in order to achieve the
best results. When tilling in the fall, remove vines and
long grass to prevent them from wrapping around the
tine shaft and slowing your tilling operation.
Grasp recoil starter handle with one hand and grasp
tiller handle with other hand. Pull rope out slowly until
engine reaches start of compression cycle (rope will
pull slightly harder at this point).
Pull recoil starter handle quickly. Do not let starter
handle snap back against starter.
If engine fires but does not start, move choke control
to half choke position. Pull recoil starter handle until
engine starts.
When engine starts, slowly move choke control to
"RUN" position as engine warms up.
•
•
•
Donotleanonhandle. Thistakesweightoffthewheels
and reduces traction. To get through a really tough
section of sod or hard ground, apply upward pressure
on handle or lower the depth stake.
•
NOTE: A warm engine requires less choking to start.
•
•
Move throttle control to desired running position.
Allow engine to warm up for a few minutes before
engaging tines.
NOTE: Ifatahighaltitude(3000feet)orincoldtemperatures
(below 32°F), the carburetor fuel mixture may need to be
adjusted for best engine performance. See "TO ADJUST
CARBURETOR" in the Service and Adjustments section
of this manual.
4
3
2
1
5
6
7
NOTE: If engine does not start, see troubleshooting
points.
FIG. 14
CULTIVATING
Cultivating is destroying the weeds between rows to pre-
vent them from robbing nourishment and moisture from the
plants. At the same time, breaking up the upper layer of
soil crust will help retain moisture in the soil. Best digging
depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields
to protect small plants from being buried.
CHOKE CONTROL
•
Cultivate up and down the rows at a speed which will
allow tines to uproot weeds and leave the ground in
rough condition, promoting no further growth of weeds
and grass (See Fig. 15).
RECOIL STARTER HANDLE
FIG. 13
TILLING HINTS
CAUTION: Untilyouareaccustomedto
handlingyourtiller,startactualfielduse
with throttle in slow position (mid-way
between “FAST” and “IDLE”).
•
•
Tilling is digging into, turning over, and breaking up
packedsoilbeforeplanting.Loose,unpackedsoilhelps
root growth. Best tilling depth is 4" to 6" (10-15 cm).
A tiller will also clear the soil of unwanted vegetation.
The decomposition of this vegetable matter enriches
the soil. Depending on the climate (rainfall and wind),
it may be advisable to till the soil at the end of the
growing season to further condition the soil.
You will find tilling much easier if you leave a row un-
tilled between passes. Then go back between tilled
rows. (See Fig. 14) There are two reasons for doing
this.First, wide turns are much easier to negotiate than
about-faces. Second, the tiller won’t be pulling itself,
and you, toward the row next to it.
FIG. 15
TINE SHEAR PINS
The tine assemblies on your tiller are secured to the tine
shaft with shear pins (See “TINE REPLACEMENT” in the
Service and Adjustments section of this manual).
If the tiller is unusually overloaded or jammed, the shear
pins are designed to break before internal damage occurs
to the transmission.
•
If shear pin(s) break, replace only with those shown in
the Repair Parts section of this manual.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
SCHEDULE
E
S
S
R
S
R
S
R
N
O
U
U
O
U
O
H
C
U
O
S
A
A
E
E
S
E
R
5 H
25 H
50 H
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Y
R
Y
R
Y
R
Y
R
O
E
F
E
E
V
E
V
E
SERVICE DATES
V
E
V
E
B
E
E
Check Engine Oil Level
Change Engine Oil
1,2
Oil Pivot Points
Inspect Spark Arrester / Muffler
Inspect Air Screen
Clean or Replace Air Cleaner Cartridge
Clean Engine Cylinder Fins
Replace Spark Plug
2
RH Gear Case Grease Fitting (1oz.)
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
LUBRICATION CHART
GENERAL RECOMMENDATIONS
The warranty on this tiller does not cover items that have
beensubjectedtooperatorabuseornegligence. Toreceive
fullvaluefromthewarranty,theoperatormustmaintaintiller
as instructed in this manual.
!THROTTLE
CONTROL
Some adjustments will need to be made periodically to
properly maintain your tiller.
" ENGINE
# RH GEAR CASE
GREASE FITTIG
All adjustments in the Service and Adjustments section
of this manual should be checked at least once each
season.
•
Once a year you should replace the spark plug, clean
or replace air filter, and check tines and belts for wear.
A new spark plug and clean air filter assure proper
air-fuel mixture and help your engine run better and
last longer.
! DEPTH
STAKE PIN
! LEVELING
SHIELD
HINGES
BEFORE EACH USE
•
•
•
Check engine oil level.
Check tine operation.
Check for loose fasteners.
! IDLER
BRACKET
! WHEEL
HUB
! SAE 30 OR 10W-30 MOTOR OIL
" REFER TO MAINTENANCE “ENGINE” SECTION
# EP #1 GREASE
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to
prevent accidental starting of engine.
Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank
before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.
Do not touch hot muffler or cylinder fins as contact may cause burns.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SF-SJ. Select the oil’s SAE viscosity grade
according to your expected temperature.
OIL
DRAIN
PLUG
SAE VISCOSITY GRADES
SAE 30
10W-30 / 5W-30
-20°
0°
30°
40°
4°
100°
30° 40°
60°
80°
°
°
F
C
-20°
10°
-30°
-10°
20°
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
FIG. 16
FIG. 17
NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
40°F (4°C). Check your engine oil level more frequently to
avoid possible engine damage from running low on oil.
AIR FILTER (See Fig. 18)
Yourenginewillnotrunproperlyusingadirtyairfilter. Clean
the foam pre-cleaner after every 25 hours of operation or
every season. Service paper cartridge every 100 hours of
operation or every season, whichever occurs first.
Change the oil after every 25 hours of operation or at
least once a year if the tiller is not used for 25 hours in
one year.
Service air cleaner more often under dusty conditions.
•
Remove cover screw and cover.
TO SERVICE PRE-CLEANER
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Add SAE
30 motor oil or equivalent. Tighten oil filler plug securely
each time you check the oil level.
•
•
•
•
•
•
Remove foam pre-cleaner from air cleaner cover.
Wash it in liquid detergent and water.
Squeeze it dry in a clean cloth.
If very dirty or damaged, replace pre-cleaner.
Reinstall pre-cleaner into air cleaner cover.
Reinstall cover and secure screw.
TO CHANGE ENGINE OIL (See Figs. 16 and 17)
Determine temperature range expected before oil change.
All oil must meet API service classification SF-SJ.
•
•
•
Be sure tiller is on level surface.
Oil will drain more freely when warm.
Use a funnel to prevent oil spill on tiller, and catch oil
in a suitable container.
TO SERVICE CARTRIDGE
•
Carefully remove cartridge to prevent debris from
entering carburetor. Clean base carefully to prevent
debris from entering carburetor.
•
•
Clean cartridge by tapping gently on flat surface. If
very dirty or damaged, replace cartridge.
Reinstall cartridge, cover with pre-cleaner and secure
with screw.
•
Remove drain plug. For easier removal of plug use
7/16 12 Pt. socket with extension.)
Tip tiller forward to drain oil.
After oil has drained completely, replace oil drain plug
and tighten securely.
Remove oil filler plug. Be careful not to allow dirt to
enter the engine.
Refillenginewithoil. See“CHECKENGINEOILLEVEL”
in the Operation section of this manual.
•
•
IMPORTANT: PETROLEUMSOLVENTS,SUCHASKEROSENE,
ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. THEY
MAY CAUSE DETERIORATION OFTHE CARTRIDGE. DO NOT
OILCARTRIDGE. DONOTUSEPRESSURIZEDAIRTOCLEAN
OR DRY CARTRIDGE.
•
•
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MUFFLER
COVER
KNOB
Do not operate tiller without muffler. Do not tamper with
exhaustsystem.Damagedmufflersorsparkarresterscould
create a fire hazard. Inspect periodically and replace if
necessary. If your engine is equipped with a spark arrester
screen assembly, remove every 50 hours for cleaning and
inspection. Replace if damaged.
COVER
FOAM
PRECLEANER
AIR CLEANER
CARTRIDGE
SPARK PLUG
Replace spark plugs at the beginning of each tilling sea-
son or after every 50 hours of use, whichever comes first.
Spark plug type and gap setting is shown in “PRODUCT
SPECIFICATIONS” on page 3 of this manual.
BASE
FIG. 18
TRANSMISSION
Once a season, lubricate the right hand side gear case
grease fitting with 1 oz. of EP #1 Grease.
COOLING SYSTEM (See Fig. 19)
Your engine is air cooled. For proper engine performance
and long life keep your engine clean.
CLEANING
•
•
Clean air screen frequently using a stiff-bristled
brush.
Keep cylinder fins, levers, and linkage free of dirt and
chaff.
Do not clean your tiller when the engine and transmission
are hot. We do not recommend using pressurized water
(garden hose, etc.) to clean your unit unless the gasket
area around the transmission and the engine muffler, air
filter and carburetor are covered to keep water out. Water
in engine will shorten the useful life of your tiller.
•
•
•
Clean engine, wheels, finish, etc. of all foreign mat-
ter.
Keep finished surfaces and wheels free of all gasoline,
oil, etc.
Protect painted surfaces with automotive type wax.
BLOWER
HOUSING
AIR SCREEN
FIG. 19
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come
into contact with plug.
TILLER
CLEVIS
PIN
TO ADJUST HANDLE HEIGHT (See Fig. 20)
Select handle height best suited for your tilling conditions.
Handle height will be different when tiller digs into soil.
NUT “C”
•
•
First loosen handle lock lever.
Handle can be positioned at different settings between
“HIGH” and “LOW” positions.
NUT
“D”
•
Retighten handle lock lever securely after adjusting.
HANDLE
(HIGH POSITION)
HAIRPIN
CLIP
HANDLE LOCK
LEVER
NUT “B”
INNER SIDE
SHIELD
NUT “A”
OUTER SIDE
SHIELD
HANDLE
(LOW POSITION)
FIG. 21
TO REMOVE BELT GUARD (See Fig. 22)
NOTE: For ease of removal, remove hairpin clip and
clevis pin from left wheel. Pull wheel out from tiller about
1 inch.
FIG. 20
•
•
Remove two (2) screws from side of belt guard.
Remove hex nut and washer from bottom of belt guard
(located behind wheel).
Pull belt guard out and away from unit.
Replace belt guard by reversing above procedure.
TIRE CARE
CAUTION: When mounting tires, un-
lessbeadsareseated,overinflationcan
cause an explosion.
•
•
•
•
Maintain 20 PSI (1.4 kg/cm2) of tire pressure. If tire
pressures are not equal, tiller will pull to one side.
Keep tires free of gasoline or oil which can damage
rubber.
SCREW
AND WASHER
BELT GUARD
HEX NUT
AND
WASHER
(LOCATED
BEHIND
TIRE)
TO REMOVE WHEEL (See Fig. 21)
•
•
•
Place blocks under transmission to keep tiller from
tipping.
Remove outer side shield by removing nuts “A” and
“B”.
Remove inner side shield by removing nuts “C” and
“D”.
•
•
•
Remove hairpin clip and clevis pin from wheel.
Remove wheel and tire.
Repair tire and reassemble.
SCREW
AND
HAIRPIN CLIP AND
CLEVIS PIN
WASHER
FIG. 22
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
GROUND DRIVE BELT ADJUSTMENT (See
TO REPLACE GROUND DRIVE BELT (See
Fig. 23)
Fig. 23)
For proper belt tension, the extension spring should
have about 5/8 inch stretch when drive control bar is in
“ENGAGED” position. This tension can be attained as
follows:
•
•
•
Remove belt guard (See“TO REMOVE BELT GUARD”
in this section of this manual).
Remove old belt by slipping off engine pulley first then
remove from transmission pulley.
Place new belt in groove of transmission pulley and
into engine pulley. BELT MUST BE IN GROOVE ON
TOP OF IDLER PULLEY. NOTE POSITION OF BELT
TO GUIDES.
•
Loosen cable clip screw securing the drive control
cable.
•
Slide cable forward for less tension and rearward for
more tension until about 5/8 inch stretch is obtained
while the drive control bar is engaged.
•
•
•
Check belt adjustment as described below.
Replace belt guard.
Reposition wheel and replace clevis pin and hairpin
clip.
•
Tighten cable clip screw securely.
CABLE CLIP
SCREW
ENGINE
PULLEY
DRIVE
CONTROL
CABLE
LESS
TENSION
MORE
TENSION
5/8"
EXTENSION
SPRING
IDLER
PULLEY
TRANSMISSION PULLEY
FIG. 23
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
•
To maintain the superb tilling performance of this
TINE REPLACEMENT (See Figs. 24, 25, and
machine the tines should be checked for sharpness,
wear, and bending, particularly the tines which are
next to the transmission. If the gap between the tines
exceeds 3-1/2 inches (9 cm), they should be replaced
or straightened as necessary.
26)
CAUTION: Tines are sharp. Wear
gloves or other protection when han-
dling tines.
•
New tines should be assembled as shown in Fig.
26. Sharpened tine edges will rotate rearward from
above.
A badly worn tine causes your tiller to work harder and dig
more shallow. Most important, worn tines cannot chop and
shred organic matter as effectively nor bury it as deeply as
good tines. A tine this worn needs to be replaced.
TRANSMISSION
NEW TINE
WORN TINE
TINE
TINE
FIG. 24
3-1/2" MAX
(9 CM)
FIG. 25
HAIRPIN CLIP
SHARP EDGE
COUNTER
TINE
ROTATION
HAIRPIN CLIP
SHARP EDGE
SHARP EDGES
SHEAR PIN
SHARP
EDGES
SHARP
EDGE
SHEAR PIN
FIG. 26
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
ENGINE
TO ADJUST CARBURETOR
Thecarburetorhasbeenpresetatthefactoryandadjustment
should not be necessary. However, engine performance
can be affected by differences in fuel, temperature, altitude
or load. If the carburetor does need adjustment, contact
your nearest authorized service center/department
IMPORTANT: NEVERTAMPERWITHTHEENGINEGOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH
SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACTYOURNEARESTAUTHORIZEDSERVICECENTER/
DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND
EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.
TO ADJUST THROTTLE CONTROL CABLE
(See Fig. 27)
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is
necessary, proceed as follows:
•
With engine not running, move remote throttle control
lever to “FAST” position.
•
If throttle lever on engine touches high speed stop, no
further adjustment is necessary. If throttle lever does
not touch high speed stop, continue with adjustment
procedure.
•
•
Loosen cable clamp screw.
Move throttle lever up until it touches high speed stop,
and hold in this position.
•
Tighten cable clamp screw securely.
CLAMP SCREW
CASING
AND WIRE
THROTTLE CONTROL
FIG. 27
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Immediately prepare your tiller for storage at the end of the
ENGINE OIL
Drainoil(withenginewarm)andreplacewithcleanoil. (See
“ENGINE” in the Maintenance section of this manual).
season or if the unit will not be used for 30 days or more.
CAUTION: Never store the tiller with
gasoline in the tank inside a building
where fumes may reach an open flame
orspark. Allowtheenginetocoolbefore
storing in any enclosure.
CYLINDER(S)
•
•
Remove spark plug.
Pour 1 ounce (29 ml) of oil through spark plug hole into
cylinder.
•
•
Pull starter handle slowly several times to distribute
oil.
Replace with new spark plug.
TILLER
•
Cleanentiretiller(See“CLEANING”intheMaintenance
section of this manual).
•
Inspect and replace belts, if necessary (See belt re-
placement instructions in the Service and Adjustments
section of this manual).
Lubricate as shown in the Maintenance section of this
manual.
Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
OTHER
•
•
•
•
Do not store gasoline from one season to an-
other.
•
•
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your unit indoors and cover it to give
protection from dust and dirt.
Cover your unit with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your unit to rust.
•
ENGINE
IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.
FUEL SYSTEM
IMPORTANT:ITISIMPORTANTTOPREVENTGUMDEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
ASTHE CARBURETOR, FUEL FILTER, FUEL HOSE, ORTANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.
•
•
Drain the fuel tank.
Start the engine and let it run until the fuel lines and
carburetor are empty.
•
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
•
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in mini-
mizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain
the gas tank and carburetor if using fuel stabilizer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
Will not start
1. Out of fuel.
1. Fill fuel tank.
2. Engine not “CHOKED” properly.
3. Engine flooded.
4. Dirty air cleaner.
5. Water in fuel.
2. See “TO START ENGINE” in Operation section.
3. Wait several minutes before attempting to start.
4. Clean or replace air cleaner cartridge.
5. Drain fuel tank and carburetor, and refill tank with fresh
gasoline.
6. Clogged fuel tank.
6. Remove fuel tank and clean.
7. Loose spark plug wire.
8. Bad spark plug or improper gap.
9. Carburetor out of adjustment.
10. Oil soaked air filter.
7. Make sure spark plug wire is seated properly on plug.
8. Replace spark plug or adjust gap.
9. Make necessary adjustments.
10. Replace air filter.
Hard to start
1. Throttle control not set properly.
2. Dirty air cleaner.
3. Bad spark plug or improper gap.
4. Stale or dirty fuel.
5. Loose spark plug wire.
6. Carburetor out of adjustment.
1. Place throttle control in “FAST” position.
2. Clean or replace air cleaner cartridge.
3. Replace spark plug or adjust gap.
4. Drain fuel tank and refill with fresh gasoline.
5. Make sure spark plug wire is seated properly on plug.
6. Make necessary adjustments.
Loss of power
1. Engine is overloaded.
2. Dirty air cleaner.
3. Low oil level/dirty oil.
4. Faulty spark plug.
5. Oil in fuel.
1. Set depth stake for shallower tilling.
2. Clean or replace air cleaner cartridge.
3. Check oil level/change oil.
4. Clean and regap or change spark plug.
5. Drain and clean fuel tank and refill, and clean carburetor.
6. Drain fuel tank and refill with fresh gasoline.
7. Drain fuel tank and carburetor, and refill tank with fresh
gasoline.
6. Stale or dirty fuel.
7. Water in fuel.
8. Clogged fuel tank.
8. Remove fuel tank and clean.
9. Spark plug wire loose.
10. Dirty engine air screen.
11. Dirty/clogged muffler.
12. Carburetor out of adjustment.
13. Poor compression.
9. Connect and tighten spark plug wire.
10. Clean engine air screen.
11. Clean/replace muffler.
12. Make necessary adjustments.
13. Contact an authorized service center/department.
Engine overheats
1. Low oil level/dirty oil.
2. Dirty engine air screen.
3. Dirty engine.
4. Partially plugged muffler.
5. Improper carburetor adjustment.
1. Check oil level/change oil.
2. Clean engine air screen.
3. Clean cylinder fins, air screen, and muffler area.
4. Remove and clean muffler.
5. Adjust carburetor to richer position.
Excessive bounce/
difficult handling
1. Ground too dry and hard.
1. Ground too wet.
1. Moisten ground or wait for more favorable soil
conditions.
Soil balls up or clumps
1. Wait for more favorable soil conditions.
Engine runs but tiller
won’t move
1. Drive control bar is not engaged.
2. V-belt not correctly adjusted.
3. V-belt is off pulley(s).
1. Engage drive control.
2. Inspect/adjust V-belt.
3. Inspect V-belt.
Engine runs but labors
when tilling
1. Tilling too deep.
2. Throttle control not properly adjusted.
3. Carburetor out of adjustment.
1. Set depth stake for shallower tilling.
2. Check throttle control setting.
3. Make necessary adjustments.
Tines will not rotate
1. Shear pin(s) broken.
1. Replace shear pin(s).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
HANDLE ASSEMBLY
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
21
23
532 18 11-27 Handle
532 08 67-77 Screw, Hex Washer Hd. Slotted
#10-24 x 1/2
532 00 94-84 Clip
532 15 92-31 Cable, Clutch
1
532 18 06-34 Control, Throttle
532 00 92-66 Grip, Handle
532 15 92-28 Bar Assembly, Control
532 18 06-76 Panel, Control
2
4
24
26
27
29
30
31
33
37
41
6
8
871 19 10-08 Screw, Truss Hd. #10-24 UNC x 1/2
532 12 47-97 Grip, Handle
873 90 04-00 Nut Hex Flange 1/4-20 Unc
873 73 10-00 Nut, Keps #10-24 UNC
532 10 41-64 Tie, Cable
10
11
12
13
14
15
16
17
18
19
20
532 12 47-88 Clip, Hairpin
532 08 13-28 Bolt, Shoulder
532 15 06-96 Bolt, Pivot
532 10 93-35 Handle, Shift
872 14 04-04 Bolt, Carriage 1/4-20 UNC x 1/2
532 10 26-04 Grip, Bar, Control
532 10 27-44 Clamp, Bar, Control
532 10 93-13 Grommet, Rubber
532 10 93-37 Rod, Shift
872 11 06-08 Bolt, Carriage 3/8-16 x 1 Gr. 5
532 10 92-29 Lock, Handle
873 68 06-00 Nut, Crownlock 3/8-16 Unc
819 13 16-11 Washer 13/32 x 1 x 11 Ga.
532 10 92-28 Lever, Lock, Handle
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
MAINFRAME, LEFT SIDE
9
532 08 67-77 Screw, Hex, Washer Head, Slotted
#10-24 x 1/2
KEY PART
NO. NO.
10
11
12
13
14
15
16
19
21
22
23
532 00 94-84 Clip
810 04 04-00 Washer, Lock 1/4
873 22 04-00 Nut, Hex 1/4-20
823 23 05-06 Screw, Set, Hex 5/16-18 x 3/8
532 11 06-52 Spacer, Split 0.327 x 0.42 x 2.09
819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.
532 14 51-02 Sheave, Transmission
812 00 00-28 Retainer, Ring
532 15 61-17 Spacer, Split
DESCRIPTION
30
31
32
33
34
35
36
37
38
39
40
44
65
532 15 92-29 Bracket, Idler
532 10 23-84 Bolt, Hex 5/16-16 x 12
532 10 21-41 Shaft, Idler Arm
874 76 06-16 Bolt, Hex 3/8-16 x 1
532 10 23-83 Counterweight, L. H.
874 76 05-32 Bolt, Hex 5/16-18 x 2
532 10 23-31 Bracket, Reinforcement, L. H.
532 13 08-12 Sheave, Engine
874 76 05-44 Bolt, Fin Hex 5/16-18 UNC x 2-3/4
532 14 00-62 Cap, Plunger Blk
874 77 05-08 Bolt, Fin Hex 5/16-24 UNF x 1/2
532 00 50-15 Tire
532 12 43-66 Rim
532 12 47-18 Tire Valve
532 17 04-88 Screw Hex Wsh Slt #10-24 x 1/2
873 80 05-00 Nut Lock Hex w/Ins 5/16-18 Unc PL
873 97 05-00 Nut Lock Hex Flange
24
25
26
27
28
29
532 12 68-75 Rivet, Drilled
532 12 47-88 Clip, Hairpin
532 16 67-92 Guard, Belt
532 13 28-01 Belt, V
NOTE: All component dimensions given in U.S.
532 10 46-79 Pulley, Idler
inches. 1 inch = 25.4 mm
812 00 00-32 Ring, Klip
21
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
MAINFRAME, RIGHT SIDE
16
15
1
2
2
2
13
3
12
4
5
6
7
8
9
11
10
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
1
532 16 65-32 Bumper
12
13
532 12 68-75 Rivet, Drilled
532 00 50-15 Tire
2
873 97 05-00 Locknut, Hex, Flange 5/16-18
819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.
874 76 05-12 Bolt, Hex 5/16-18 x 3/4
532 10 23-32 Bracket, Reinforcement
874 76 05-32 Bolt, Hex 5/16-18 x 2
532 10 21-73 Counter Weight, R.H.
810 04 06-00 Washer, Lock 3/8
3
532 12 43-66 Rim
4
532 12 47-18 Tire Valve
- - - - - - - -
5
15
16
Engine, Briggs & Stratton
Model No. 121402 (Order parts
from Engine Manufacturer)
6
7
8
532 12 47-56 Tie Cable
9
873 22 06-00 Nut, Hex 3/8-16
10
11
874 76 05-24 Bolt, Hex 5/16-18 x 1-1/2
532 12 47-88 Clip, Hairpin
NOTE: All component dimensions given in U.S.inches.
1 inch = 25.4 mm
22
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
TRANSMISSION
KEY PART
NO. NO.
DESCRIPTION
24
25
27
28
29
30
31
32
33
34
35
36
810 04 07-00 Washer, Lock 7/16
873 61 07-00 Nut, Hex 7/16-20
532 14 30-09 Bearing, Shaft, Ground Drive L.H.
532 10 63-90 Spacer 0.765 x 1.125 x 1.23
532 10 21-34 Chain #35-50 Pitch
532 15 07-37 Ground Shaft Assembly
532 14 30-08 Bearing, Shaft, Ground Drive R.H.
532 10 63-88 Spacer 0.70 x 1.00 x 1.150
532 10 21-21 Sprocket and Gear Assembly
532 10 21-12 Shaft, Reduction (2nd)
532 10 21-01 Screw, Whiz, Lock 5/16-18 x 3-1/2
532 15 43-55 Sprocket Assembly w/Bearing (In-
cludes Key Nos. 37 and 38)
532 12 47-91 Bearing, Needle
532 15 43-56 Sprocket, Tine
532 10 53-45 Gear, Cluster, Red 1st & 2nd
532 10 53-46 Gear, Reverse
532 00 83-58 Shaft, Reduction (1st)
532 00 42-20 Washer, Thrust
KEY PART
NO. NO.
DESCRIPTION
1
532 18 06-77 Transmission Assembly (Includes
Key Nos. 2-53)
532 18 06-27 Gearcase, L.H. w/Bearing (Includes
Key No. 4)
2
3
532 16 19-63 Gasket, Gearcase
532 00 50-20 Bearing, Needle
532 00 13-70 Washer, Thrust 5/8 x 1.10 x 1/32
532 13 73-35 Pinion, Input
4
37
38
39
40
41
42
43
44
48
5
6
7
532 14 51-01 Shaft, Input
8
532 12 47-92 Bearing, Needle
532 15 44-67 Washer, Seal
532 12 46-97 Ball, Steel
9
10
11
12
13
14
15
16
18
19
20
532 10 61-46 Spacer 1.01 x 1.75 x 0.760
532 15 52-36 Seal Asm, Oil
532 18 06-31 Gearcase, R.H. w/Bearing (In-
cludes Key No. 8)
532 13 26-88 Shaft, Tine
532 10 03-71 Spring, Shift, Fork
532 10 61-60 O-Ring
532 14 21-45 Arm, Shift
532 00 83-53 Fork, Shift
49
50
51
52
53
58
60
- -
812 00 00-39 Ring, Klip
532 10 61-47 Chain, Roller #50-50 Pitch
817 72 04-08 Screw 1/4-20 x 1/2
873 22 05-00 Nut, Hex 5/16-18
532 15 44-66 Shaft, Shift
532 00 43-58 Washer
812 00 00-40 Ring, Klip
532 16 51-40 Kit, Bearing
532 10 21-14 Gear, Assembly, Reverse Idler (In-
cludes Key Nos. 21 and 22)
532 10 21-15 Gear, Reverse Idler
532 00 68-03 Bearing, Needle
532 10 21-11 Shaft, Reverse Idler
532 17 95-20 Bolt Shoulder 1/4-20 Unc x .875
532 12 48-36 Fitting Grease
21
22
23
532 00 60-66 Grease, Plastilube #1
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
23
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
TINE SHIELD
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
1
873 90 05-00 Nut, Lock Hex Flange 5/16-18
532 16 29-52 Shield, Side, Outer L. H.
532 00 83-93 Pin, Stake, Depth
19
20
21
22
23
24
25
26
27
28
29
30
32
33
532 10 27--01
873 22 06-00 Nut, Hex 3/8-16
532 10 21-56 Stake, Depth
874 93 06-32 Bolt, Hex 3/8-16 x 2
532 00 44-40 Hinge
872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr. 5
532 12 47-17 Cap, Vinyl
532 10 92-27 Pad, Idler
532 12 50-16 Shield, Leveling
532 12 05-88 Pin, Hinge
532 14 22-93 Shield, Side
Grip
2
3
4
812 00 00-35 Ring, Klip
5
532 18 08-47 Bolt, Rdhd Sqnk 5/16-18 x 3/4
532 00 83-94 Spring
532 00 83-92 Bracket, Latch
532 10 92-30 Spring, Depth Stake
532 14 22-92 Shield, Tine
872 14 05-08 Bolt, Carriage 5/16-18 UNC x 1
873 22 05-00 Nut, Hex 5/16-18
810 04 05-00 Washer, Lock 5/16
872 11 05-10 Bolt, Carriage 5/16-18 x 1-1/4
532 12 43-11 Bracket, Shield Tine
532 16 29-53 Shield, Side, Outer R.H.
873 90 04-00 Nut, Hex Flange 1/4-20 UNC
872 04 04-10 Bolt, Carriage 1/4-20 x 1-1/4 Gr.
6
7
8
9
10
11
12
13
14
15
16
18
873 97 05-00 Locknut, Flange 5/16-18
873 22 04-00 Nut Fin Hex 1/4-20 UNC
810 04 04-00 Washer Lock Hvy Helical 1/4
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
TINE ASSEMBLY
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
1
2
3
4
5
6
7
532 00 44-59 Tine, Outer, L.H.
532 13 26-73 Clevis Pin
532 00 65-54 Tine, Inner, L.H.
532 12 46-60 Retainer, Spring Zinc
532 13 27-27 Assembly, Hub and Plate, L.H.
873 61 06-00 Nut, Hex 3/8-24
810 04 06-00 Washer, Lock 3/8
8
874 61 06-16 Bolt, Hex 3/8-24 x 1
532 00 44-60 Tine, Outer, R.H.
532 13 27-28 Assembly, Hub and Plate, R.H.
532 00 65-55 Tine, Inner, R.H.
9
10
11
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30
DECALS
3
2
1
8
10
6
5
7
11
9
KEY PART
NO. NO.
DESCRIPTION
1
532 17 70-07 Decal, Blt Grd
532 17 59-97 Decal, CNTRL PNL
532 18 08-13 Decal, Logo
2
3
5
532 11 06-14 Decal, Hand Placement
532 10 21-80 Decal, Shift Indicator
532 16 23-84 Decal, Warning
532 17 10-79 Decal, Engine B&S 6.5 HP
532 12 00-76 Decal, Warning, Rotating Tines
532 16 68-69 Decal, Engine Intek REF
532 17 10-78 Decal, Rewind Intek #274350
532 18 48-25 Manual, Owner’s (English)
532 18 48-26 Manual, Owner’s (French)
6
7
8
9
10
11
- -
- -
26
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY STATEMENT
SECTION 1: LIMITED WARRANTY
SECTION 4: EXCEPTIONS AND LIMITATIONS
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur-
chaser to be free from defects in material and workmanship from the date of purchase for the “Warranty
Period” of the product as set forth below:
This warranty shall be inapplicable to defects resulting from the following:
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,
corrosion, or any adverse reaction due to incorrect storage or use habits;
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruc-
tion sheet furnished by Husqvarna;
(3)Alterations or modifications that change the intended use of the product or affects the product’s per-
formance, operation, safety, or durability, or causes the product to fail to comply with any applicable
laws; or:
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand
held product.
3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)
2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area
walks, and ground engaging commercial equipment.
(4)Additional damage to parts or components due to continued use occurring after any of the above.
2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors,
walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld
blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for
noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO
THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RE-
SERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE,
Emission control system components necessary to comply with CARB-TIER-II and EPA regulations,
except for those components which are part of engine systems manufactured by third party engine manu-
facturers for which the purchaser has received a separate warranty with product information supplied at
time of purchase.
AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY
UCTS.
MANUFACTURED PROD-
1Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-pro-
fessional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hover-
ing trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection
systems used for commercial, institutional, professional or income producing purposes or use.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.
90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole prun-
ers, snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any
Husqvarna product used for commercial, institutional, professional, or income producing purposes or use
except as otherwise provided herein.
SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written
in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur,
the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof
of purchase, as explained in section 6, rests solely with the customer.
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase
for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Prod-
uct must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must
be followed as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not
covered under warranty.
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly
filled out and mailed to Husqvarna Forest & Garden Company.This card should be mailed within ten (10) days
from the date of purchase in order to confirm the warranty and to facilitate post-sale service.
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty ser-
vice.This proof must include date purchased, model number, serial number, and complete name and address
of the selling dealer.
Husqvarna will repair or replace defective components without charge for parts or labor if a component
fails because of a defect in material or workmanship during the warranty period.
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an au-
thorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.
The following items are not covered by this warranty:
(1)Normal customer maintenance items which become worn through normal regular use, including,
but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs,
saw chain, spark plugs, starter ropes and tines;
(2)Natural discoloration of material due to ultraviolet light;
HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respec
tive manufacturer’s warranty as provided in writing with the product information supplied at the time
of purchase; all claims must be sent to the appropriate manufacturer;
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for
warranty should be sent to the manufacturer; and
531 83 81-23 2002
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regula
tions which are manufactured by third party engine manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
532 18 48-25 Rev. 1 05.13.03 TR
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|