IPL, MC-18, 2007-09, 542 20 11-33
MC-18
Spare Parts & Operator’s Manual
Piezas de repuesto y Manual del operador
MC 18 9H
MC 18 13H
542 20 11-33
HUSQVARNA CONSTRUCTION PRODUCTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbol Definitions
Definición De Simbolos
• Please Read The Instructions For Use Prior To Operating The Machine For The First Time.
• Antes De La Puesta En Marcha, Lea Detenidamente Las Instrucciones Y Familiaricese Con La Máquina.
• Mandatory
• Obligatorio
• Indication
• Indicación
• Prohibition
• Prohibición
• Warning Triangle
• Triángwulo De Advertencia
• Wear Eye Protection
• Usar Gafas De Protección
• Wear Head Protection
• Usar Casco De Protección
• Wear Breathing Protection
• Usar Máscara De Protección
• The Use Of Ear Protection Is Mandatory
• Es Obligatorio El Uso De Protección Auditiva
• Wear a Hard Hat
• Usar Casco Duro
• Wear Safety Shoes
• Usar Zapatos De Seguridad
• Wear Appropriate Clothing
• Usar Ropa Adecuada
• Remove The Blade Prior To Hoisting, Loading, Unloading And Transporting The Machine On Jobsite
• Desmontar El Disco Antes De Desplazar, Cargar, Descargar O Transportar La Máquina En La Obra
• Motor Off
• Parar El Motor
• Use In Well Ventilated Area
• Usar En Una Área Bien Ventilada
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do Not Use In Flammable Areas
• No Usar In Áreas Inflamables
• Machinery Hazard, Keep Hands And Feet Clear
• Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina
• Danger, Poison Exhaust Gas
• Peligro, Gas De Escape Venenoso
• No Non-working Personnel In Area
• Prohibido Para Personas Ajenas A La Obra
• No Smoking
• No Fumar
• Do Not Operate Without All Guards In Place
• No Operar Sin Todas Las Protecciones In Su Sitio
• Always Keep the Blade Guards In Place
• Mantenga Siempre Las Protecciones De La Hoja En Su Sitio
• Water Supply On
• Suministro De Agua Desconectado
• Water Supply Off
• Suministro De Agua Des Conectado
• Keep Work Area Clean/Well Lit, Remove All Safety Hazards
• Mantenga Limpio El Sitio De Trabajo/Bien Iluminado, Elimine Todos Los Riesgos De Seguridad
• Dangerously High Noise Level
• Nivel De Ruido Elevadamente Peligroso
• Pay Extreme Attention To The Care And Protection Of The Machine Before Starting Up
• Ponga Extrema Atención Al Cuidado Y Preparación De La Máquina Antes De Ponerla En Marcha
• Remove Tools From Area And Machine
• Elimine Las Herramientas Del Área Y De La Máquina
• Oil Required
• Necesita Aceita
• Dipstick, Maintain Proper Oil Level
• Varilla De Control, Mantenga El Nivel De Aceite Correcto
• Lubrication Point
• Punto De Lubrication
• Unleaded Fuel Only
• Combustible Sin Piomo Solamente
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Repairs Are To Be Done By An Authorized Dealer Only
• Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado
• Diamond Blade
• Sierra Diamantada
• Blade Diameter
• Diámetro De La Hoja
• Pulley Diameter
• Diámetro De La Correa
• Number of Revolutions Per Minute, Rotational Speed
• N° De Revoluciones Por Minuto, Velocidad De Rotación
• Blade Flange Diameter
• Diámetro De La Brida De La Hoja
• Machine Mass (lbs)
• Masa De La Máquina (lbs)
• Engine
• Motor
• Engine Speed Revolutions/Minute
• Velocidad Del Motor En Revoluciones Por Minuto (RPM)
• Engine Start
• Arranque Del Motor
WARNING
HEARING HAZARD
DURING NORMAL USE OF THIS MACHINE, OPERATOR MAY BE EXPOSED TO A NOISE
LEVEL EQUAL OR SUPERIOR TO 85 dB (A)
ATENCION
RIESGO DE DAÑO AUDITIVO
EN CONDICIONES NORMALES DE UTILIZACIÓN, EL OPERADOR DE ESTA MÁQUINA PUEDE
ESTAR EXPUESTO A UN NIVEL DE RUIDO IGUAL O SUPERIOR A 85 dB (A)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DECAL DESCRIPTIONS AND LOCATIONS
DECRIPCIÓN DE CALCAMONIAS Y UBICACIONES
P/N 542190733
Location: Front of Frame
Quantity: 1
P/N 50249101
Location: Belt Guard
Quantity: 1
P/N 174998
Location: Top of Screw Feed Bracket
Quantity: 1
P/N 040563
Location: Front of Frame
Quantity: 1
P/N 177588
Location: Top of Belt Guard
Quantity: 1
P/N 542169065
Location: Engine Fuel Tank
Quantity 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MC 18 Specifications
Power Source
MC 18 Model
Horsepower
Gas
MC 18 9H
9 HP
MC 18 13H
13 HP
Screw Feed Model
ALL SAWS FEATURE:
18 (450)
4-5/8"-6-5/8" (117.5-168.3mm)
2,600
209 (95)
182 (83)
Max. Blade Cap. in. (mm)
Max. Depth of Cut
Blade Shaft RPM
Weight Crated - lb. (Kg)
Uncrated - lb. (Kg)
Arbor Size
2600
222 (101)
195 (88)
1" (25.4mm)
Blade Flange
Blade Drive
Blade Control
Blade Coolant
Axle Front
4-1/2" dia. with drive pin
3 V-belts (9 & 13 HP engine)
Spring assisted screw feed
Removable dual water spray tubes; water supply connector located on left side of saw; control
3/4" (19 mm) diameter; raises and lowers cutting head
Wheels Front
Rear
Chassis
5" x 1-1/2" x 3/4" (102 x 38 x 19mm); solid rubber tires, cast iron hub, roller bearings, lube fitting
8" x 2" x 5/8" (203 x 51 x 15.9mm); ball bearings; semi-pneumatic tires
One piece reinforced box base
POWER SOURCE:
Honda
Honda
Engine/Motor
Gas Engine
GX270
Gas Engine
GX390
Specifications
Max. Horsepower
Displacement cu. in. (cc)
Bore - in. (mm)
Stroke - in. (mm)
Cylinders/Stroke
Fuel Capacity - gal. (l)
Oil Capacity - pt.(l)
Air Filter
9 HP
13 HP
23.7 (389)
3.5 (88)
2.5 (64)
1/4
1.72 (6.5)
2.3 (1.1)
Dry type
dual element
w/pre cleaner
16.5 (270)
3.0 (76)
2.3 (58)
1/4
1.59 (6.0)
2.3 (1.1)
Dry type
dual element
w/pre cleaner
Recoil
Starter
Engine Coolant
Oil Sentry
Recoil
Air
Standard
Air
Standard
SAW DIMENSIONS: Inches (mm)
Crated Dimensions: L-35" x H-30-1/2" x W-22" (889 x 775 x 559mm)
Inches
47-1/2
45-1/2
Metric (mm)
(1207)
(1156)
A - Height (Max.) - In. (mm)
B - Saw Length, Pointer Up
C - Max. Saw Length, Pointer
Down & Handles Out
E - Pointer Extension
F - Frame Width
G - Frame Length
H - Saw Width
I - Front Axle Length
J - Rear Wheel Track
K - Blade to Wall
64-1/4
18-3/4
16
22-1/2
22
10-1/4
19-1/2
2-3/8
15
(1632)
(476)
(406)
(572)
(559)
(260)
(495)
(61)
L - Wheel Base Length
(381)
Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
SAFETY FIRST!
WARNINGS
DO’s and DO NOT’s
WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING
INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY.
DO
DO read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls.
DO keep all guards in place and in good condition.
DO wear safety approved hearing, eye, head and respiratory protection.
DO read and understand all warnings and instructions on the machine.
DO read and understand the symbol definitions contained in this manual.
DO keep all parts of your body away from the blade and all other moving parts.
DO know how to stop the machine quickly in case of emergency.
DO turn the “ON/OFF” switch to the “OFF” position prior to connecting the electric powered model to the power source.
DO inspect the blade, flanges and shafts for damage before installing the blade.
DO use the blade flange size shown for each blade size.
DO use only steel center diamond blades manufactured for use on concrete saws.
DO use only reinforced abrasive blades or steel center diamond blades manufactured for use on concrete saws.
DO use only the blade flanges supplied with the saw. Never use damaged or worn blade flanges.
DO use only blades marked with a maximum operating speed greater than the blade shaft speed. Verify speed by checking blade shaft
rpm and pulley diameters.
DO verify saw drive configuration by checking blade shaft RPM, pulley diameters, and blade flange diameter.
DO read all safety materials and instructions that accompany any blade used with this machine.
DO inspect each blade carefully before using it. If there are any signs of damage or unusual wear, DO NOT USE THE BLADE.
DO mount the blade solidly and firmly. Wrench tighten the arbor nut.
DO make sure the blade and flanges are clean and free of dirt and debris before mounting the blade on the saw.
DO use the correct blade for the type of work being done. Check with blade manufacturer if you do not know if blade is correct.
DO use caution and follow the instructions when loading and unloading the machine.
DO operate this machine only in well ventilated areas.
DO instruct bystanders on where to stand while the machine is in operation.
DO establish a training program for all operators of this machine.
DO clear the work area of unnecessary people. Never allow anyone to stand in front of or behind the blade while the engine is
running.
DO make sure the blade is not contacting anything before starting the engine.
DO use caution when lifting and transporting this machine.
DO always tie down the machine when transporting.
DO use caution and follow instructions when setting up or transporting the machine.
DO have all service performed by competent service personnel.
DO make sure electric powered machines are plugged into a properly grounded circuit.
DO make sure power cords are the proper size and in good condition.
DO verify the blade arbor hole matches the machine spindle before mounting the blade
DO always check for buried electrical cables before sawing. If unsure, contact the local utilities.
DO clean the machine after each day’s use.
DO follow all electrical codes in your area.
DO consider work area environment. Don’t expose power tools to rain. Don’t use power tools in wet locations.
DO use caution to guard against electric shock. Prevent body contact with grounded surfaces (i.e., pipes, radiators, ranges,
refrigerators).
DO use correct voltage and proper extension cords. Never carry tool by cord or yank it to disconnect it from receptacle. Keep cord
away from heat, oil and sharp edges.
DO always transport the machine with the motor stopped.
DO keep the handles dry, clean and free of oil and dirt.
DO disconnect tools from power source when not in use, before servicing and when changing accessories.
DO carefully maintain and clean for better and safer performance. Follow instructions for changing accessories. Inspect tool cords peri-
odically and, if damaged, have repaired by authorized service facility.
DO always give a copy of this manual to the equipment user. If you need extra copies, call TOLL FREE 1-800-288-5040.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST!
WARNINGS
DO’s and DO NOT’s
WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING
INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY.
DO NOT
DO NOT operate this machine unless you have read and understood this operator’s manual.
DO NOT operate this machine without the blade guard, or other protective guards in place.
DO NOT stand behind or in front of the blade path while the engine/motor is running.
DO NOT leave this machine unattended while the engine/motor is running.
DO NOT work on this machine while the engine/motor is running.
DO NOT operate this machine when you are tired or fatigued.
DO NOT use a wet blade without adequate water supply to the blade.
DO NOT exceed maximum blade speed shown for each blade size. Excessive speed could result in blade breakage.
DO NOT operate the machine if you are uncertain of how to run the machine.
DO NOT use damaged equipment or blades.
DO NOT touch or try to stop a moving blade with your hand.
DO NOT cock, jam, wedge or twist the blade in a cut.
DO NOT transport a cutting machine with the blade mounted on the machine.
DO NOT use a blade that has been dropped or damaged.
DO NOT
use carbide tipped blades.
DO NOT touch a dry cutting diamond blade immediately after use. These blades require several minutes to cool after each cut.
DO NOT use damaged or worn blade flanges.
DO NOT allow other persons to be near the machine when starting, refueling, or when the machine is in operation.
DO NOT operate this machine in an enclosed area unless it is properly vented.
DO NOT operate this machine in the vicinity of anything that is flammable. Sparks could cause a fire or an explosion.
DO NOT allow blade exposure from the guard to be more than 180 degrees.
DO NOT operate this machine with the belt guard or blade guard removed.
DO NOT operate this machine unless you are specifically trained to do so.
DO NOT use a blade that has been over heated. (Core has a bluish color.)
DO NOT jam material into the blade.
DO NOT grind on the side of the blade.
DO NOT lay power cords in or near the water.
DO NOT tow this machine behind a vehicle.
DO NOT replace the motor with any motor that does not have a special grounding connection.
DO NOT operate this machine while under the influence of drugs or alcohol.
*****************
This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which
it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Diamant
Boart, Inc. and we have advised you.
Husqvarna Constructuion Products N. A.
17400 West 119th Street
Olathe, Kansas 66061
USA
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 1
FIGURE 2
2H
2B
2A
2 I
2F
2D
2E
2A. BLADE SHAFT NUT: Use to tighten the outer flange
against the diamond blade.
2B. OUTER FLANGE: Use to hold the diamond blade in
position.
2C. NOT USED
2D. LOCKING PIN: Use to prevent the diamond blade
from rotating on the shaft during operation.
2E. DIAMOND BLADE: Use as the cutting tool for
concrete and asphalt surfaces.
2F. INNER FLANGE: Inside support used to hold the
diamond blade in position.
2G. NOT USED
1A. WATER VALVE: Use to control the water supply to
2H. BLADE GUARD FRONT: The front section of the
the diamond blade.
blade guard.
1B. WATER INLET: Connect water hose at this garden
2I.
BLADE SHAFT: Supports the blade flanges and
hose connection.
1C. HANDLE ADJUSTMENT KNOBS: Use to adjust
handle height.
1D. ENGINE STOP SWITCH: Stop Switch: Push down
to stop engine.
1E. DEPTH CONTROL LOCK: Use to lock the position
of the Depth Control Hand Wheel.
1F. DEPTH CONTROLHAND WHEEL: Controls lowering
and raising of the blade into and out of the cut.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE OPERATION CHECKLIST
Before leaving our factory, every machine is thoroughly tested. Follow our instructions strictly and
your machine will give you long service in normal operating conditions.
Before starting up the machine, make sure you read this entire operations manual and are familiar
with the operation of the machine.
WITH MACHINE COLD AND SETTING LEVEL:
1.
Check engine oil. Fill to full mark on dip stick with 10W30 oil. DO NOT OVERFILL!!
• Gas Models: Class MS, SD, SE or better.
1 - 2 HOUR OPERATION CHECK:
ALWAYS park machine on a level surface with the engine “OFF” and the engine switch set in the
“OFF” position before performing any maintenance. Let the machine cool down!!
1.
Tension the blade drive V-belts. DO NOT over tension!!
SCHEDULED MAINTENANCE QUICK REFERENCE:
Before performing any maintenance, ALWAYS park the machine on a level surface with the engine
“OFF” and the engine switch set in the “OFF” position.
SERVICE DAILY:
NOTE: See engine manual for specific engine maintenance
for your specific model.
1. Check engine oil level.
2. Check blade guard for damage.
3. Check engine air filter, replace if dirty.
4. Lubricate bladeshaft bearings.
5. Lubricate front wheel bearings.
6. Check blade drive V-belt tension. DO NOT over
tension!!! Change in sets only!
SERVICE EVERY 50 HOURS:
1. Replace engine oil and filter.
2. Clean engine/motor air fins.
3. Lubricate depth control adjustment screw. (Screw
Feed version only.)
4. Check wheels for wear or damage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICATION
INFORMATION
INSTRUCTION
2
Assembly
MANDATORY
WARNING
•
The Handle must be attached. Place Handle
in position and securely tighten Knobs.
PROHIBITION
•
Check the engine oil level. Service before using.
Refer to the engine operation manual for detailed
information.
3
General Instructions
These signs will give
advice for your safety
Remove the Blade (2E) before transport.
Before leaving our factory every machine is
thoroughly tested.
WARNING: DO NOT operate without the proper
blade guard over the Blade! (2E)
Follow our instructions strictly and your ma-
chine will give you long service in normal operating
WARNING: DO NOT operate the saw with the
front of the Blade Guard (2H) raised!
1
Features
Use: Wet sawing of old and new concrete and asphalt.
Tools: Diamond blades — water cooled, Ø: 10", 12", 14",
18" and 20" with Arbor Ø - 1"
WARNING: Blade exposure CANNOT exceed
180 degrees when operating!
(For information, contact your Husqvarna supplier)
CUTTING DEPTHS
•
•
The Front Pointer must be checked for alignment with
the Blade (2E). It must be in line with the Blade (2E)
mounted on the Blade Shaft (2I).
MAXIMUM
BLADE DEPTH
(To Collar)
MC18
BLADE SIZE
MAXIMUM DEPTH
(To Depth Stop)
2 1/2" (62mm)
3-1/2" (87mm)
4-1/2" (112mm)
6-1/2" (158mm)
10" (250mm)
12" (300mm)
14" (350mm)
18" (450mm)
2 3/4" (68mm)
3-3/4" (93mm)
4-3/4" (118mm)
6-3/4" (164mm)
For WET SAWING, be sure the water jets in the blade
guard water tubes are open and that each side of the
Blade (2E) has an adequate supply of water. Test the
water supply for pressure and quantity (flow) before
starting to saw.
Before starting up the machine, make
sure you read this entire manual and are
familiar with the operation of this
machine.
WATER FLOW from 2-1/2 to 5 gallons of
water per minute MUST flow over the blade
to properly cool it and to get maximum blade
life. DO NOT use conventional (wet) diamond
blades without water!
The working area must be completely clear,
well lit and all safety hazards removed.
•
•
Saw only as deep as the specifications and job
conditions require. Sawing excessively deep is
wasteful–avoid it! Step cut in increments of 2 inches
(50 mm) for best results.
The operator must wear
p r o t e c t i v e c l o t h i n g
appropriate to the work he
is doing.
Saw in a straight line. Mark the cutting line clearly so
the saw operator can follow the line without difficulty.
The saw should NOT be twisted from side to side try-
ing to force the blade back on the line.
Any persons not involved in the work, should
leave the area.
Use only blades marked with a maximum
operating speed greater than the bladeshaft
speed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Starting The Power Source
4
Check Before Starting
Always pay extreme care and attention to the
preparation of the machine before starting.
Remove all wrenches and tools from the floor
and the machine.
Take into account the working conditions from
the health and safety point of view.
Always keep blade guard and transmission
guard in place.
FUEL: Check the engine maintenance manual.
* Gas Models: Unleaded gasoline is recommended.
Check that the engine oil level is correct. Because
the engine often operates at an angle, check the oil
level (with engine horizontal) frequently to ensure that
the oil level never falls below the lower mark on the
dipstick. 10W30 oil is recommended.
•
On Gasoline Engine Models:
1. Refer to the engine operating manual for proper engine
operation.
2. Fill the engine fuel tank and check the engine oil level.
Refer to the engine manual for detailed information.
5
Fitting The Blade
3. Start the engine. Refer to the engine manual for detailed
information.
(See Fig. 1 and 2)
4. Let the engine warm up at half throttle. All sawing is
done at full throttle. The governor is factory set for the
correct engine speed. Do not change the Governor
setting – it is factory set for the correct speed.
Always set the Engine Switch (1D) to the "OFF"
position before mounting the Blade (2E).
•
•
Set the Engine Switch (1D) to the "OFF" position.
Raise the machine to a high position [by cranking the
Raise/Lower Hand Wheel].
Raise the front half of the Blade Guard (2H).
Unscrew the Blade Shaft Nut (2A). Remove Outer
Flange (2B).
WARNING: To STOP ENGINE, PUSH the
Engine Stop Switch DOWN, located on the
handle support of the saw. [Wait for all engine
movement to stop.]
•
•
•
•
Fit Diamond Blade (2E) on the Blade Shaft Arbor.
Install Outer Flange (2B) into the Blade Shaft (2I)
makingsurethattheLockingPin(2D)passesthroughthe
Diamond Blade (2E) and into the Inner Flange (2F).
Note the direction of rotation of the blade. The
direction of rotation is shown by an arrow on
the Diamond Blade (2E). Make sure that the
contact surfaces on the Diamond Blade (2E),
Inner & Outer Flanges (2B & 2F) and Blade
Arbor are clean.
•
•
•
Rotate Outer Flange (2B) and the Blade (2E) in the
opposite direction of blade rotation to remove back-
lash.
Install and tighten Blade Flange Nut using the Blade
Shaft Wrench [50 lb.-ft. (68 N-m)] while firmly holding
the Diamond Blade (2E).
Lower front half of Blade Guard (2H).
The Blade Shaft Nut (2A) on the Right Hand
side has Left Hand threads.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Stopping the Saw
7
8
To Maneuver the Saw
•
•
Set the handle bar height to a comfortable position.
•
Screw Feed Version:
Raise the blade out of the cut by pulling up on the
depth control lock and slowly turning the hand wheel
clockwise. Raise the blade (2E) high enough out of
the cut to clear the pavement when maneuvering the
saw.
Raise the Blade (2E) as high as possible so that
the Blade (2E) will not strike pavement when
To Start Sawing
•
•
•
Turn off the Water Valve (1A).
•
•
Follow all of the instructions outlined above.
Open the Water Valve (1A) FULL open. Check the
water to verify full flow, then adjust for proper amount
of water on the blade BEFORE you lower the Blade.
Turn the Engine Throttle to the IDLE position.
STOP the engine by turning the Engine Switch (1D)
to the OFF position.
Test for adequate water supply [2-1/2 to 5
gal/min (10 to 20 lit./min)]. Low water flow will
cause damage to diamond blades.
If water supply is interrupted, stop cutting
immediately.
Screw Feed Version:
•
Lower the blade into the cut by pulling up on the Depth
Control Lock (1E) and slowly turning the Hand Wheel
COUNTER-CLOCKWISE. When the desired depth of
cut is reached, push Depth Control Lock down to lock
it in the hand wheel.
•
During cutting, DO NOT exert excessive side pressure
on the Handle Bars to attempt to “STEER” the saw.
Use only enough pressure to follow the previously
marked line.
•
•
If the saw should stall for any reason, raise the blade
completely out of the cut before starting your power
source again!
When lowering the Blade (2E) into a partially made
cut, the blade must be perfectly aligned within the cut
before starting to saw again. DO NOT FORCE the
Blade (2E) into the material by lowering the Blade too
fast, or by propelling the saw too fast.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Maintenance
11
Optional and Accessory (Field Installed)
SPECIAL OUTER FLANGE ASSY 1/2" (12.7mm)
WIDE CUT (P/N 167963)
Before performing any maintenance, ALWAYS
park the machine on a level surface with the
Engine OFF and the Engine Switch in the "OFF"
position.
•
A Special Outer Flange Assembly is available as a
field installed accessory. It enables the MC 18 to cut
7/16" - 1/2" (11-12.7mm) wide.
After each use: CLEAN the machine.
WARNING: This special outer flange assembly
is for use with blade width stacks of 7/16" - 1/2"
(11mm-12.7mm) only! If blade width stacks of
less than 7/16" (11mm) are required, use the
standard outer flange assembly supplied with
the MC 18. The Special Outer Flange Assembly
can be identified by the COUNTERBORE on the
“Nut Side” of the flange. The Standard Outer
Flange Assembly has NO COUNTERBORE.
LUBRICATION:
LUBRICATE DAILY
Front Wheels and Blade Shaft Bearings
LUBRICATE EVERY 50 HOURS
Depth Control Adjustment Screw (Screw Feed Version
Only)
WATER TANK KIT
A 6 gallon (23 liter) Water Tank Kit is available as a
•
NOTE: When cutting dry, lubricate blade shaft bearings 2 or
3 times daily, the grease provides an added protective seal
for the bearings. Use only a Premium Lithium 12 based
Grease, conforming to NLG1 Grade #2 Consistency, without
Molybdenum Disulfide.
Field installed accessory. Use only for dry cutting!
The water tank is designed only to suppress airborne
concrete dust.
WARNING: DO NOT use conventional (wet)
diamond blades with the water tank as the
water source, because there is not sufficient wa-
ter flow available to properly cool the blades!
ENGINE OIL:
Check daily. Keep the oil clean and at the proper level.
10W30 MS, SD, SE or better is generally recommended.
Capacity levels indicated on page 10. DO NOT OVERFILL!!
Change engine oil and oil filter every 50 HOURS of operation.
Refer to the engine manual for detailed information.
TIE DOWN BRACKET KIT (P/N 167189)
•
A Tie Down Bracket Kit is available as a field installed
accessory. The kit consists of two (2) tie down loops
that are installed at the front of the frame. They are to
be used only to SECURE the saw to a truck or trailer
during transport.
CLEAN ENGINE AIR FILTER:
Clean the air filter 2 or 3 times daily when dry cutting. Refer
to the engine manual for detailed information.
ENGINE CARE:
Refer to the engine manual for detailed information.
WARNING: DO NOT use the tie down
brackets as a device for lifting the saw!
15
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Governor Speed
13
Repairs
It is critical that the Governor and throttle on all internal
combustion engines be adjusted properly. The engine speed
is preset at the factory for the proper sawing speed. It is
NOT normally necessary to change this setting. It should be
periodically verified after the saw is placed into service. To
change the Governor setting, refer to the engine manual.
We carry out all repairs in the shortest possible time and at
the most economical prices. (See back page for our address
and phone numbers.)
14
Service Parts
WARNING: Overspeeding the blade can result
in blade breakage and/or personal injury to the
operator and bystanders!! To assure the proper
Governor adjustment, determine the correct
blade shaft speed from the following chart.
Follow the engine manufacturer’s instruction
procedure for Governor and throttle setting.
For quick supply of spare parts and to avoid any lost time,
it is essential to quote the data on the manufacturer’s plate
fixed to the machine and the part number (s) to be replaced
with every order.
Write the Model Number & Serial Number here for future
reference:
Model Number:____________________
Serial Number:____________________
NO LOAD BLADE SHAFT AND ENGINE R.P.M.s
BLADE SHAFT ENGINE
MODEL
R.P.M.
R.P.M.
9H 14"/18"
13H-14"/18"
2610
2610
3600
3600
The instructions for use and spare parts found in this document are for infor-
mation only and are not binding. As part of our product quality
improvement policy, we reserve the right to make any and all technical
modifications without prior notice.
The manufacturer accepts no
responsibility caused by unsuitable
use or modifications
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
NOTA:
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 1 – Frame & Axle
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 1 – Frame & Axle
BILL OF MATERIAL
DESCRIPTION
1 502470001 Frame Weldment, MC18
INDEX P/N
QTY
1
1
1
4
2
2 174942
3 174975
4 020768
5 040091
Axle, Front
Axle, Pivot
Washer, Flat .75 SAE
Wheel Assy, 5 Inch Dia
6 541201090 Lock Collar, .750 ID (w/ss)
2
1
4
2
3
7 020551
8 020767
9 139569
Screw, Set Soc Cup Pt .312-18UNC x .25
Washer, Flat .625 SAE
Wheel, 8 Inch Dia
10 541200649 Lock Collar, .625 w/SS
11 020551
12 139638
13 020323
14 020199
15 139582
Screw, Set Soc Cup Pt .312-18UNC x .25
Anchor, Spring
Capscrew, Hex Hd .375-16UNC x 1.00
Locknut, Fiber .375-16UNC
Bolt, Tension
1
1
2
2
1
16 020140
17 020766
18 020201
19 139581
21 174946
Nut, Std Hex .500-13UNC
Washer, Flat .500 SAE
Locknut, Fiber .500-13UNC
Spring
1
1
1
2
1
Handle, Bent
22 542139568 Grip, Handle
2
2
1
1
23 177557
24 163988
25 197170
Knob, 3/8-16UNC-2A x 1.00
Wrench, 1-1/16" Open End
Wing Bolt, M6 x 1.0 x 16 mm
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 2 – Depth Control (Screw Feed)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 2 – Depth Control (Screw Feed)
BILL OF MATERIAL
INDEX P/N
1 174997
2 049924
DESCRIPTION
QTY
1
1
Adj Nut Wldmnt w/ Grease Fit
Fitting, Grease 1/8 NPT x 90°
3 542177915 Screw, Adj., .625-8 ACME
4 542190434 Bearing, Flange, .50 Inch ID
5 502469901 Bracket, Screw Feed
1
1
1
6 020764
7 020786
8 020330
9 040153
10 040151
Washer, Flat .375 SAE
Lockwasher, Split .375
Capscrew, Hex Hd .375-16UNC x 3.00
Assy, Hand Wheel
4
4
4
1
1
Wheel, Hand - Machined
11 032250
12 020766
13 174956
14 020552
15 174994
Handle Assy, Revolving
Washer, Flat .500 SAE
Bracket, Stop
Screw, Set Soc Cup Pt .312-18UNC x .50
Spacer, Adjustment Screw
1
2
1
1
1
16 160164
17 020540
18 177239
19 040183
20 174961
Pin, Clevis .50 Dia x 1.13 Lg
Screw, Set Soc Cup Pt .250-20UNC x .25
Pin, Rue Ring - .50 DIA
Rubber Boot, 3 Inch (20 ribs)
Hose Clamp, Worm Drive SAE 24 Narrow
1
1
1
1
2
21 020010
22 020012
23 020762
24 020195
25 020788
Key, Woodruff #405
Bolt, Carriage .250-20UNC x 1.00
Washer, Flat .250 SAE
Locknut, Fiber .250-20UNC
Lockwasher, Split .500
1
2
2
2
1
26 030210
27 020668
28 174998
Nut, Acorn LT .500-13UNC
Capscrew, Hex Hd .500-13UNC x .75
Decal, Screw Feed
1
1
1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 3 – Pointer & Belt Guard
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 3 – Pointer & Belt Guard
BILL OF MATERIAL
INDEX P/N
DESCRIPTION
QTY
1
1 502469601 Guard, Shaft - Weldment
2 020785
3 020399
4 502469701 Bracket, Pointer Mount
5 502437601 Bar, Pointer - Offset
Lockwasher, Split .313
Capscrew, Hex Hd .312-18UNC x 3.25
2
2
1
1
6 502437701 Bar, Pointer - Straight
1
1
1
1
1
7 041231
8 041220
9 020786
10 020136
Rod, Pointer
Wheel, 3in Dia
Lockwasher, Split .375
Nut, Std Hex .375-16UNC
11 020199
12 172137
13 162761
14 020395
15 020195
Locknut, Fiber .375-16UNC
Rope, Pointer
Clamp
Capscrew, Soc Hd .250-20UNC x .625
Locknut, Fiber .250-20UNC
1
1
2
2
2
16 139749
17 139748
18 040550
19 020786
20 020323
Capscrew, Hex Hd M10 x 1.50 x 25mm
Locknut, Fiber M10 x 1.50
Hinge Block, Pointer
4
4
1
1
1
Lockwasher, Split .375
Capscrew, Hex Hd .375-16UNC x 1.00
21 177696
22 020199
Draw Bolt, 3/8-16UNC
Locknut, Fiber .375-16UNC
1
1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 4 – Guards & Water Distribution
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 4 – Guards & Water Distribution
BILL OF MATERIAL
INDEX P/N
DESCRIPTION
QTY
1
1 502469801 Guard, Belt
2 020785
3 020313
4 174992
5 139021
Lockwasher, Split .313
4
4
1
Capscrew, Hex Hd .312-18UNC x .75
Water Valve Assy, MC18
Water Valve
1
6 169196
7 539300267 Hose Adapter
8 045640
9 040254
10 139616
Elbow, 1/2NPT Male x 90° Brass
1
1
1
1
1
Filter Washer
Washer, Hose
Hose Assy, Water - MC18
11 020782
12 196039
13 195129
14 020743
15 020233
Lockwasher, Split #10
2
2
1
1
1
Screw, Rd Hd Mach 10-24 x .500 Cross Z/P
Assy, Blade Guard - 18in Husq Gray
Washer, Flat .375 Dia
Capscrew, Hex Hd .375-16UNC x 3.75
16 020199
17 020742
18 020785
19 020313
Locknut, Fiber .375-16UNC
Washer, Flat .313 Dia
Lockwasher, Split .313
1
1
1
1
Capscrew, Hex Hd .312-18UNC x .75
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 5 – Blade Guard
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 5 – Blade Guard
BILL OF MATERIAL
DESCRIPTION
50244701 Rear Guard Weldment - 18 Inch Husq Gray
195127 Hinge
139596 Front Guard Weldment, 18 Inch Husq Gray
173059 Washer, Flat M8
167478 Capscrew, Hex Hd M8 x 1.25 x 25mm
INDEX P/N
QTY
1
1
1
6
1
2
3
4
5
6
6
7
8
9
139738 Locknut, Fiber M8 x 1.25
139098 Splash Flap
167761 Capscrew, Hex Hd M5 x 0.8 x 20mm
173047 Washer, Flat M5
6
1
4
2
2
10
172316 Locknut, Fiber M5 x 0.8
11
12
13
14
15
020782 Lockwasher, Split #10
172011 Nut, Hex Hd M5 x 0.80
040330 Spring, .375 OD x .054 Dia
049212 Clamp, Water Tube
167818 Capscrew, Slot Flat Hd M6 x 1.0 x 16mm
2
4
1
2
4
16
17
18
19
20
139745 Locknut, Fiber M6 x 1.0
167046 Water Tube, 18 Inch
020864 Plug, Soc Hd 1/8 NPT Brass
139051 Gasket, Water Manifold
139045 Water Manifold, Machined
8
2
2
1
1
21
22
040275 Adapter, 3/8 NPT x Male Garden Hose
167551 Capscrew, Hex Hd M6 x 1.0 x 40mm
1
4
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 6 – Engine & Bladeshaft
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 6 – Engine & Bladeshaft
BILL OF MATERIAL
INDEX P/N DESCRIPTION
QTY
1
1
2
1
1 174973 Group, Bladeshaft R&L 4.5 (9H,13H)
2 177569 Bladeshaft Assy, Complete (9H,13H)
3 167185 Collar, Inner 4.50 OD
4 167962 Collar, Outer 4.50 OD Assy
5 167964 Pin, Drive
1
6 167846 Nut, LH Thread, Bladeshaft
7 167847 Nut, RH Thread, Bladeshaft
8 020067 Key, Square .250 x 1.25 Lg
9 139300 Pulley Assy, 3GR 3V 3.65 (9H,13H)
10 020541 Screw, Set Soc Cup Pt .250-20UNC x .375
1
1
1
1
4
11 162633 Bearing, 1in Pillowblock BB
12 174962 Spacer, Bearing
13 020743 Washer, Flat .375 Dia
14 020330 Capscrew, Hex Hd .375-16UNC x 3.00
15 020199 Locknut, Fiber .375-16UNC
2
2
8
4
4
16 177958 Engine, 13HP Honda - Modified
-- 167751 Engine, 9HP Honda - Modified
17 174962 Spacer, Bearing (9R,13R,13H)
18 174736 Plate, Adapter (13H Only)
19 020743 Washer, Flat .375 Dia
1
1
2
2
8
20 020786 Lockwasher, Split .375 (13H Only)
21 020377 Capscrew, Hex Hd .375-16UNC x 1.50 (13H)
-- 020380 Capscrew, Hex Hd .375-16UNC x 1.75 ( 9H)
22 020322 Capscrew, Hex Hd .375-16UNC x .75 (13H)
23 048740 Capscrew, Hex Hd .375-16UNC x 1.25 (13H)
24 020199 Locknut, Fiber .375-16UNC
7
4
4
3
1
4
1
25 167133 Adapter, M12 x 10mm Hose Barb (9H,13H)
26 167305 Hose Assembly, Oil Drain
27 020049 Hose Clamp, Worm Drive
28 167306 Cap, Blanking
29 167622 Tube Nut, M16
30 174999 Assy, Cord
1
1
1
1
1
31 167746 Pulley Assy, 3G3V 2.65 Dia (w/ss)
32 020540 Screw, Set Soc Cup Pt .250-20UNC x .25
33 020067 Key, Square .250 x 1.25 Lg
34 139613 V-Belt, 3VX300 [set of 3](13H)
-- 139614 V-Belt, 3VX280 [set of 3]( 9H)
35 047455 V-Belt, 3VX300 (13H)
1
2
1
1
1
3
1
-- 058020 V-Belt, 3VX280 ( 9H)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 7 – Kit, Water Tank (174957)
BILL OF MATERIAL
INDEX P/N
DESCRIPTION
QTY
1
1 502479401 Bracket, Water Tank
2 174648
3 020764
4 020509
5 020199
Water Tank (w/cap), 7 Gallon
1
Washer, Flat .375 SAE
4
Capscrew, Hex Hd .375-16UNC x 2.00
Locknut, Fiber .375-16UNC
2
4
6 020322
7 139722
8 020049
9 174016
10 174741
Capscrew, Hex Hd .375-16UNC x .75
Hose, 3/8 ID x 4.4
2
1
2
1
Hose Clamp, Worm Drive
Fitting, Hose Barb 3/8 ID x 3/4 Male
Kit: Quick Disconnect Garden Hose w/Valve 1
11 196037
12 187667
13 196038
14 187667
Fitting, 3/4 FGH SWV x 1/4 HB Nylon
Hose, 1/4 ID x 7in
Fitting, 1/4 Y Nylon LP
Hose, 1/4 ID x 9in
1
1
1
2
30
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES / NOTAS:
Download from Www.Somanuals.com. All Manuals Search And Download.
Husqvarna Construction Products N. A.
Corporate Office
17400 West 119th Street
Olathe, Kansas 66061
Tel. 913-928-1000
Fax 913-438-7951
Customer Service: 800-288-5040
Customer Serv. Fax: 800-825-0028
DUST WARNING
Cutting, especially when DRY cutting, generates dust that comes from the material being cut,
which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount of such dust can cause:
Respiratory diseases (affecting your ability to breath), including chronic bronchitis, silicosis
and pulmonary fibrosis from exposure to silica. These diseases may be fatal;
Skin irritation and rash; and
Cancer according to NTP* and IARC*
*National Toxicology Program / International Agency for Research on Cancer
Take precautionary steps
Avoid inhalation of and skin contact with dust, mist and fumes;
Wet cut when feasible, to minimize dust;
Wear and ensure that all bystanders wear appropriate respiratory protection such as dust
masks designed to filter out microscopic particles. (See OSHA 29 CFR Part 1910.1200)
California Prop 65 Warning:
Use of this product can cause exposure to materials known to the State of California to cause cancer
and/or birth defects or other reproductive harm.
Printed in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|