Operator’s manual
345e EPA III 346XP EPA I
353 EPA IIITrioBrake
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY TO SYMBOLS
You will find the following labels on your chain saw:
EPA I
EPA III
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal emissions requirements.
Maintenance, replacement, or repair of the emission control
devices and system may be performed by any nonroad
engine repair establishment or individual.
The engine exhaust from this product
contains chemical known to the State
of California to cause cancer, birth
defects or other reproductive harm.
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Bar and chain combinations ...................................... 41
Contents
KEY TO SYMBOLS
Saw chain filing and file gauges ................................ 41
FEDERAL EMISSION CONTROL WARRANTY
STATEMENT
Symbols on the machine: .........................................
Symbols in the operator’s manual: ...........................
CONTENTS
YOUR WARRANTY RIGHTS AND OBLIGATIONS ... 42
AMERICAN STANDARD SAFETY PRECAUTIONS
Safety precautions for chain saw users ..................... 43
Contents ...................................................................
INTRODUCTION
6
Dear customer! .........................................................
WHAT IS WHAT?
What is what on the chain saw? ...............................
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw ..................................
Important ..................................................................
Always use common sense ......................................
Personal protective equipment .................................
Machine′s safety equipment .....................................
Cutting equipment .................................................... 11
ASSEMBLY
Fitting the bar and chain ........................................... 17
FUEL HANDLING
Fuel .......................................................................... 19
Fueling ...................................................................... 20
Fuel safety ................................................................ 20
STARTING AND STOPPING
Starting and stopping ............................................... 21
WORKING TECHNIQUES
Before use: ............................................................... 23
General working instructions .................................... 23
How to avoid kickback .............................................. 30
MAINTENANCE
General ..................................................................... 31
Carburetor adjustment .............................................. 31
Checking, maintaining and servicing chain saw safety
equipment ................................................................. 32
Muffler ...................................................................... 34
Starter ...................................................................... 35
Air filter ..................................................................... 36
Spark plug ................................................................ 36
Lubricating the bar tip sprocket ................................ 37
Needle bearing lubrication ........................................ 37
Adjustment of the oil pump ....................................... 37
Cooling system ......................................................... 37
”Air Injection” centrifugal cleaning ............................ 38
Heated handles ........................................................ 38
Electrical carburetor heating ..................................... 38
Winter use ................................................................ 38
Maintenance schedule ............................................. 39
TECHNICAL DATA
Technical data .......................................................... 40
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear customer!
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when
the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets.
The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different products, from wood
stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers
appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest
priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as well as for
building and construction industry.
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer
who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time.Think of this operator′s
manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and the second-hand
value of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the
operator′s manual, so they will also know how to properly maintain and use it.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
27
32
26
25
24
35
18
19
31
23
6
5
20
4
21 22
1
7
8
9
2
13 14 15
10 11 12
16 17
29
30
28
What is what on the chain saw?
1
2
3
4
5
6
7
8
9
Product and serial number plate
Throttle lockout
Decompression valve
Front handle
19 Chain oil tank
20 Starter
21 Fuel tank
22 Choke control/Start throttle lock
23 Rear handle
Cylinder cover
Front hand guard
Muffler
24 Stop switch
25 Adjuster screws carburetor
26 Air purge
Bumper spike
Bar tip sprocket
27 Information and warning decal
28 Bar guard
10 Rear handle with right hand guard
11 Throttle control
12 Clutch cover
29 Combination spanner
30 Operator’s manual (EPA)
31 Right-hand brake trigger
13 Oil pump adjustment screw
14 Chain catcher
32 Switch for heated handle (346XPG TrioBrake, 353G
TrioBrake)
15 Chain tensioning screw
16 Bar
33 Knob (345e TrioBrake)
34 Chain tensioner wheel (345e TrioBrake)
35 Felling direction mark
17 Chain
18 Starter handle
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw
Important
•
Please read this manual carefully.
IMPORTANT!
•
Check that the cutting equipment is correctly fitted and
adjusted. See instructions under the heading Assembly.
The machine is only designed for cutting wood.
You should only use the saw with the bar and chain
combinations we recommend in the chapter Technical
data.
•
•
•
Refuel and start the chain saw. See the instructions
under the headings Fuel Handling and Starting and
Stopping.
Never use the machine if you are fatigued, while under the
influence of alcohol or drugs, medication or anything that
could affect your vision, alertness, coordination or
judgement.
Do not use the chain saw until sufficient chain oil has
reached the chain. See instructions under the heading
Lubricating cutting equipment.
Long-term exposure to noise can result in permanent
hearing impairment. So always use approved hearing
protection.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
Do not modify this product or use it if it appears to have
been modified by others.
WARNING! Under no circumstances may
the design of the machine be modified
!
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures must
be carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
without the permission of the manufacturer.
Always use genuine accessories. Non-
authorized modifications and/or
accessories can result in serious personal
injury or the death of the operator or others.
Your warranty may not cover damage or
liability caused by the use of non-
authorized accessories or replacement
parts.
Never use any accessories other than those
recommended in this manual. See instructions under the
headings Cutting equipment and Technical data.
CAUTION! Always wear protective glasses or a face visor
to reduce the risk of injury from thrown objects. A chain
saw is capable of throwing objects, such as wood chips,
small pieces of wood, etc, at great force.This can result in
serious injury, especially to the eyes.
WARNING! A chain saw is a dangerous tool
if used carelessly or incorrectly and can
cause serious, even fatal injuries. It is very
important that you read and understand the
contents of this operator’s manual.
!
WARNING! Running an engine in a confined
or badly ventilated area can result in death
due to asphyxiation or carbon monoxide
poisoning.
WARNING!The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of
a damaged muffler.
!
WARNING! Faulty cutting equipment or the
wrong combination of bar and saw chain
increases the risk of kickback! Only use the
bar/saw chain combinations we
recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
WARNING! Long term inhalation of the
engine’s exhaust fumes, chain oil mist and
dust from sawdust can represent a health
risk.
!
WARNING! The ignition system of this
machine produces an electromagnetic field
Always use common sense
!
during operation.This field may under
some circumstances interfere with
pacemakers.To reduce the risk of serious
or fatal injury, we recommend persons with
pacemakers to consult their physician and
the pacemaker manufacturer before
operating this machine.
It is not possible to cover every conceivable situation you can
face when using a chain saw. Always exercise care and use
your common sense. Avoid all situations which you consider
to be beyond your capability. If you still feel uncertain about
operating procedures after reading these instructions, you
should consult an expert before continuing. Do not hesitate
to contact your dealer or us if you have any questions about
the use of the chain saw. We will willingly be of service and
provide you with advice as well as help you to use your chain
saw both efficiently and safely. Attend a training course in
chain saw usage if possible.Your dealer, forestry school or
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
your library can provide information about which training
Generally clothes should be close-fitting without restricting
materials and courses are available.
your freedom of movement.
IMPORTANT! Sparks can come from the muffler, the bar
and chain or other sources. Always have fire extinguishing
tools available if you should need them.Help prevent forest
fires.
′
Machine s safety equipment
In this section the machine’s safety features and their
function are explained. For inspection and maintenance see
instructions under the heading Checking, maintaining and
servicing chain saw safety equipment. See instructions
under the heading, What is what?, to find where these parts
are located on your machine.
Work is constantly in progress to improve the design and
technology - improvements that increase your safety and
efficiency.Visit your dealer regularly to see whether you can
benefit from new features that have been introduced.
The life span of the machine can be reduced and the risk of
accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
Personal protective equipment
WARNING! Never use a machine with
defective safety components. Safety
equipment must be inspected and
maintained. See instructions under the
heading Checking, maintaining and
servicing chain saw safety equipment. If
your machine does not pass all the checks,
take the saw to a servicing dealer for repair.
WARNING! Most chain saw accidents
happen when the chain touches the
!
operator.You must use approved personal
protective equipment whenever you use the
machine. Personal protective equipment
cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident
does happen. Ask your dealer for help in
choosing the right equipment.
Chain brake and front hand guard
Your chain saw is equipped with a chain brake that is
designed to stop the chain if you get a kickback. The chain
brake reduces the risk of accidents, but only you can prevent
them.
Take care when using your saw and make sure the kickback
zone of the bar never touches any object.
•
•
•
•
•
•
Approved protective helmet
Hearing protection
Protective goggles or a visor
Gloves with saw protection
Trousers with saw protection
Boots with saw protection, steel toe-cap and non-slip
sole
•
The chain brake (A) can either be activated manually (by
your left hand) or automatically by the inertia release
mechanism.
•
•
Always have a first aid kit nearby.
Fire Extinguisher and Shovel
A
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
The brake is applied when the front hand guard (B) is
•
To release the chain brake pull the front hand guard
pushed forwards or when the right-hand brake trigger (E)
is pushed up and forwards.
backwards, towards the front handle.
B
E
•
Kickback can be very sudden and violent. Most
kickbacks are minor and do not always activate the chain
brake. If this happens you should hold the chain saw
firmly and not let go.
•
This movement activates a spring-loaded mechanism
that tightens the brake band (C) around the engine drive
system (D) (clutch drum).
•
The way the chain brake is activated, either manually or
automatically by the inertia release mechanism,
depends on the force of the kickback and the position of
the chain saw in relation to the object that the kickback
zone of the bar strikes.
If you get a violent kickback while the kickback zone of
the bar is farthest away from you the chain brake is
designed to be activated by the inertia in the kickback
direction.
•
The front hand guard is not designed solely to activate
the chain brake. Another important feature is that it
reduces the risk of your left hand hitting the chain if you
lose grip of the front handle.
•
•
The chain brake must be engaged when the chain saw is
started to prevent the saw chain from rotating.
If the kickback is less violent or the kickback zone of the
bar is closer to you the chain brake is designed to be
activated manually by the movement of your left hand.
Use the chain brake as a ”parking brake” when starting
and when moving over short distances, to reduce the risk
of moving chain accidentally hitting your leg or anyone or
anything close by.
•
In the felling position the left hand is in a position that
makes manual activation of the chain brake impossible.
With this type of grip, that is when the left hand is placed
so that it cannot affect the movement of the front hand
guard, the chain brake can only be activated by the
inertia action.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Will my hand always activate the chain
Chain catcher
brake during a kickback?
The chain catcher is designed to catch the chain if it snaps
or jumps off. Replace it if necessary with an aluminium chain
catcher (is available as spare part). This should not happen
if the chain is properly tensioned (see instructions under the
heading Assembly) and if the bar and chain are properly
serviced and maintained (see instructions under the heading
General working instructions).
No. It takes a certain force to move the hand guard forward.
If your hand only lightly touches the front guard or slips over
it, the force may not be enough to trigger the chain brake.You
should also maintain a firm grip of the chain saw handles
while working. If you do and experience a kickback, your
hand may never leave the front handle and will not activate
the chain brake, or the chain brake will only activate after the
saw has swung around a considerable distance. In such
instances, the chain brake might not have enough time to
stop the saw chain before it touches you.
There are also certain positions in which your hand cannot
reach the front hand guard to activate the chain brake; for
example, when the saw chain is held in felling position.
Will my inetria activated chain brake always
activate during kickback in the event of a
kickback?
Right hand guard
No. First your brake must be in working order. Testing the
brake is simple, see instructions under the heading
Apart from protecting your hand if the chain jumps or snaps,
the right hand guard stops branches and twigs from
interfering with your grip on the rear handle.
Checking, maintaining and servicing chain saw safety
equipment. We recommend you do before you begin each
work session. Second the kickback must be strong enough
to activate the chain brake. If the chain brake is too sensitive
it would activate all the time which would be a nuisance.
Will my chain brake always protect me from
injury in the event of a kickback?
No.First, the chain brake must be in working order to provide
the intended protection. Second, it must be activated during
the kickback as described above to stop the saw chain.
Third, the chain brake may be activated but if the bar is too
close to you the brake might not have enough time to slow
down and stop the chain before the chain saw hits you.
Vibration damping system
Your machine is equipped with a vibration damping system
that is designed to reduce vibration and make operation
easier.
Only you and proper working technique can eliminate
kickback and its danger.
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control.When you press the lock (A)
(i.e. when you grasp the handle) it releases the throttle
control (B).When you release the handle the throttle control
and the throttle lockout both move back to their original
positions.This arrangement means that the throttle control is
automatically locked at the idle setting.
The machine′s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine′s handle unit. The body of the
chain saw, including the cutting equipment, is insulated from
the handles by vibration damping units.
A
Cutting hardwoods (most broadleaf trees) creates more
vibration than cutting softwoods (most conifers). Cutting with
B
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
cutting equipment that is blunt or faulty (wrong type or badly
sharpened) will increase the vibration level.
WARNING! Never use a saw without a
muffler, or with a damaged muffler. A
damaged muffler may substantially
increase the noise level and the fire hazard.
Keep fire fighting equipment handy. If a
spark arrestor screen is required in your
area, never use the saw without or with a
broken spark arrestor screen.
!
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure to
vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes in
skin colour or condition.These symptoms
normally appear in the fingers, hands or
wrists.These symptoms may be increased
in cold temperatures.
!
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
•
•
Reduce the risk of kickback.
Reduce the risk of the saw chain breaking or jumping off
the bar.
•
•
•
Obtain optimal cutting performance.
Extend the life of cutting equipment.
Avoid increasing vibration levels.
General rules
Stop switch
•
Only use cutting equipment recommended by us!
Use the stop switch to switch off the engine.
See instructions under the heading Technical data.
•
Keep the chain’s cutting teeth properly sharpened!
Follow our instructions and use the recommended
file gauge. A damaged or badly sharpened chain
increases the risk of accidents.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
•
Maintain the correct depth gauge setting! Follow our
instructions and use the recommended depth gauge
clearance. Too large a clearance increases the risk of
kickback.
WARNING! The exhaust fumes from the
engine are hot and may contain sparks
!
which can start a fire. Never start the
machine indoors or near combustible
material!
In areas with a hot, dry climate there is a high risk of fires.
These areas are sometimes subject to government rules
requiring among other things the muffler must be equipped
with an approved type of spark arrestor screen.
•
•
Keep the chain properly tensioned! If the chain is
slack it is more likely to jump off and lead to increased
wear on the bar, chain and drive sprocket.
Keep cutting equipment well lubricated and properly
maintained! A poorly lubricated chain is more likely to
break and lead to increased wear on the bar, chain and
drive sprocket.
CAUTION! The muffler gets very hot during and after use.
This also applies during idling. Be aware of the fire hazard,
especially when working near flammable substances and/
or vapours.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
Number of drive links. The number of drive links is
determined by the length of the bar, the chain pitch and
the number of teeth on the bar tip sprocket.
Cutting equipment designed to reduce
kickback
WARNING! Faulty cutting equipment or the
wrong combination of bar and saw chain
!
increases the risk of kickback! Only use the
bar/saw chain combinations we
recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
•
Bar groove width (inches/mm). The groove in the bar
must match the width of the chain drive links.
The only way to avoid kickback is to make sure that the
kickback zone of the bar never touches anything.
By using cutting equipment with ”built-in” kickback reduction
and keeping the chain sharp and well-maintained you can
reduce the effects of kickback.
•
Chain oil hole and hole for chain tensioner.The bar must
be matched to the chain saw design.
Bar
The smaller the tip radius the lower the chance of kickback.
Chain
Chain
A chain is made up of a number of links, which are available
in standard and low-kickback versions.
•
Chain pitch (inches)
IMPORTANT! No saw chain design eliminates the danger
of kickback.
•
Drive link width (mm/inches)
Number of drive links.
WARNING! Any contact with a rotating saw
chain can cause extremely serious injuries.
!
Some terms that describe the bar and chain
To maintain the safety features of the cutting equipment, you
should replace a worn or damaged bar or chain with a bar
and chain combinations recommended by Husqvarna. See
instructions under the heading Technical Data for a list of
replacement bar and chain combinations we recommend.
•
Bar
•
Length (inches/cm)
Sharpening your chain and adjusting depth
gauge setting
•
Number of teeth on bar tip sprocket (T).
General information on sharpening cutting teeth
•
Never use a blunt chain. When the chain is blunt you
have to exert more pressure to force the bar through the
wood and the chips will be very small. If the chain is very
blunt it will produce wood powder and no chips or
shavings.
•
Chain pitch (inches).The spacing between the drive links
of the chain must match the spacing of the teeth on the
bar tip sprocket and drive sprocket.
•
A sharp chain eats its way through the wood and
produces long, thick chips or shavings.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
The cutting part of the chain is called the cutter and
Sharpening cutting teeth
consists of a cutting tooth (A) and the depth gauge (B).
The cutters cutting depth is determined by the difference
in height between the two (depth gauge setting).
To sharpen cutting teeth you will need a round file and a file
gauge.See instructions under the headingTechnical data for
information on the size of file and gauge that are
recommended for the chain fitted to your chain saw.
When you sharpen a cutting tooth there are four important
factors to remember.
1
Filing angle
•
•
Check that the chain is correctly tensioned.A slack chain
will move sideways, making it more difficult to sharpen
correctly.
2
Cutting angle
Always file cutting teeth from the inside face. Reduce the
pressure on the return stroke. File all the teeth on one
side first, then turn the chain saw and file the teeth on the
other side.
3
4
File position
Round file diameter
•
File all the teeth to the same length. When the length of
the cutting teeth is reduced to 0.16 inch (4 mm) the chain
is worn out and should be replaced.
It is very difficult to sharpen a chain correctly without the right
equipment.We recommend that you use our file gauge.This
will help you obtain the maximum kickback reduction and
cutting performance from your chain.
General advice on adjusting depth gauge setting
•
When you sharpen the cutting tooth (A) the depth gauge
setting (C) will decrease. To maintain optimal cutting
performance the depth gauge (B) has to be filed down to
achieve the recommended depth gauge setting. See
instructions under the heading Technical data to find the
correct depth gauge setting for your particular chain.
See instructions under the heading Technical data for
information about sharpening your chain.
WARNING! Departure from the sharpening
instructions considerably increases the
risk of kickback.
!
WARNING!The risk of kickback is increased
if the depth gauge setting is too large!
!
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Adjustment of depth gauge setting
346XP TrioBrake, 353 TrioBrake
•
•
The cutting teeth should be newly sharpened before
adjusting the depth gauge setting. We recommend that
you adjust the depth gauge setting every third time you
sharpen the cutting teeth. NOTE! This recommendation
assumes that the length of the cutting teeth is not
reduced excessively.
•
•
Loosen the bar nuts that hold the clutch cover/chain
brake. Use the combination spanner. Then tighten the
bar nuts by hand as tight as you can.
You will need a flat file and a depth gauge tool. We
recommend that you use our depth gauge tool to acheive
the correct depth gauge setting and bevel for the depth
gauge.
Raise the tip of the bar and stretch the chain by
tightening the chain tensioning screw using the
combination spanner. Tighten the chain until it does not
sag from the underside of the bar.
•
Use the combination spanner to tighten the bar nuts
while lifting the tip of the bar at the same time. Check that
you can pull the chain round freely by hand and that it
does not sag from the underside of the bar.
•
Place the depth gauge tool over the chain. Detailed
information regarding the use of the depth gauge tool,
will be found on the package for the depth gauge tool.
Use the flat file to file off the tip of the depth gauge that
protrudes through the depth gauge tool. The depth
gauge setting is correct when you no longer feel
resistance as you draw the file along the depth gauge
tool.
The position of the chain tensioning screw on our chain saws
varies from model to model. See instructions under the
heading What is what? to find out where it is on your model.
345e TrioBrake
Tensioning the chain
•
Release the knob by folding it out.
WARNING! A slack chain may jump off the
bar and cause serious or even fatal injury.
!
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up
the slack.
Check the chain tension every time you refuel. NOTE! A new
chain has a running-in period during which you should check
the tension more frequently.
•
Turn the knob anti clockwise to loosen the bar cover.
Tension the chain as tightly as possible, but not so tight that
you cannot pull it round freely by hand.
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
Adjust the tension on the chain by turning the wheel
Filling with chain oil
down (+) for tighter tension and up (-) to loosen the
tension.
•
All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also adjustable.
•
The saw chain oil tank and the fuel tank are designed so
that the fuel runs out before the saw chain oil.
However, this safety feature requires that you use the
right sort of chain oil (if the oil is too thin it will run out
before the fuel), and that you adjust the carburetor as
recommended (a lean mixture may mean that the fuel
lasts longer than the oil) and that you also use the
recommended cutting equipment (a bar that is too long
will use more chain oil).
•
Tighten the bar clutch by turning the knob clockwise.
Checking chain lubrication
•
Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.
•
Fold the knob back in to lock the tensioning.
Aim the tip of the bar at a light coloured surface about 20
cm (8 inches) away. After 1 minute running at 3/4 throttle
you should see a distinct line of oil on the light surface.
Lubricating cutting equipment
WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.
!
If the chain lubrication is not working:
•
Check that the oil channel in the bar is not obstructed.
Clean if necessary.
Chain oil
Chain oil must demonstrate good adhesion to the chain and
also maintain its flow characteristics regardless of whether it
is warm summer or cold winter weather.
As a chain saw manufacturer we have developed an optimal
chain oil which has a vegetable oil base.We recommend the
use of our own oil for both maximum chain life and to
minimise environmental damage. If our own chain oil is not
available, standard chain oil is recommended.
•
Check that the groove in the edge of the bar is clean.
Clean if necessary.
Never use waste oil! Using waste oil can be dangerous to
you and damage the machine and environment.
IMPORTANT! When using vegetable based saw chain oil,
dismantle and clean the groove in the bar and saw chain
before long-term storage. Otherwise there is a risk of the
saw chain oil oxidizing, which will result in the saw chain
becoming stiff and the bar tip sprocket jamming.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
Check that the bar tip sprocket turns freely and that the
lubricating hole in the tip sprocket is not blocked. Clean
and lubricate if necessary.
When the length of the cutting teeth has worn down to only
0.16 inch (4 mm) the chain must be replaced.
Bar
Check regularly:
•
Whether there are burrs on the edges of the bar.Remove
these with a file if necessary.
If the chain lubrication system is still not working after
carrying out the above checks and associated measures you
should contact your servicing dealer.
Chain drive sprocket
•
•
Whether the groove in the bar has become badly worn.
Replace the bar if necessary.
The clutch drum is fitted with one of the following drive
sprockets:
Whether the tip of the bar is uneven or badly worn. If a
hollow forms on the underside of the bar tip this is due to
running with a slack chain.
A
B
Spur sprocket (the chain sprocket is welded on the drum)
Rim sprocket (replaceable)
Regularly check the degree of wear on the drive sprocket.
Replace if wear is excessive. Replace the drive sprocket
whenever you replace the chain.
•
To prolong the life of the bar you should turn it over daily.
Needle bearing lubrication
WARNING! Most chain saw accidents
happen when the chain touches the
operator.
Both versions of sprockets have a needle bearing on the
drive shaft, which has to be greased regularly (once a week).
CAUTION! Use only high quality bearing grease or engine
oil.
!
Wear personal protective equipment. See
instructions under the heading Personal
protective equipment.
See instructions under the heading Maintenance, Needle
bearing lubrication.
Do not tackle any job that you feel you are
not adequately trained for. See instructions
under the headings Personal protective
equipment, How to avoid kickback, Cutting
equipment and General working
Checking wear on cutting equipment
Check the chain daily for:
instructions.
Avoid situations where there is a risk of
kickback. See instructions under the
′
heading Machine s safety equipment.
Use the recommended protective
equipment and check its condition. See
instructions under the heading General
working instructions.
•
•
•
Visible cracks in rivets and links.
Whether the chain is stiff.
Whether rivets and links are badly worn.
Check that all the chain saw safety features
are working. See instructions under the
headings General working instructions and
General safety precautions.
Replace the saw chain if it exhibits any of the points above.
We recommend you compare the existing chain with a new
chain to decide how badly the existing chain is worn.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Tension the chain by turning the chain tensioning screw
clockwise using the combination spanner. See instructions
under the heading Tensioning the chain.
Fitting the bar and chain
WARNING! Always wear gloves, when
working with the chain.
!
346XP TrioBrake, 353 TrioBrake
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar nuts with the
combination spanner.
Remove the bar nuts and remove the clutch cover (chain
brake). Take off the transportation ring (A).
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the chain
tension regularly. A correctly tensioned chain ensures good
cutting performance and long life.
345e TrioBrake
Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it in
the groove on the bar. Begin on the top edge of the bar.
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
Remove the knob and remove the clutch cover (chain brake).
Take off the transportation ring.
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Fit the clutch cover and locate the chain adjuster pin in the
hole in the bar. Check that the drive links of the chain fit
correctly over the drive sprocket and that the chain is
correctly located in the groove in the bar.Tighten the bar nuts
finger tight.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it in
the groove on the bar. Begin on the top edge of the bar.
tension regularly. A correctly tensioned chain ensures good
cutting performance and long life.
Note: If clutch cover is difficult to remove, replace bar nuts,
engage brake and rerelease (an audible click will be heard if
released properly).
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Install the clutch cover and locate the chain tensioner pin in
the clutch cover. Check that the chain’s drive links fit
correctly over the drive sprocket and that the chain is
correctly located in the groove in the bar. Install the chain
tensioning pulley but do not tighten.
Tension the chain by turning the wheel down (+). The chain
should be tensioned until it does not sag from the underside
of the bar.
The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar knob by turning
the knob clockwise.
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the chain
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing ratio
Fuel
1:50 (2%) for all engines.
Note!The machine is equipped with a two-stroke engine and
must always be run using a mixture of gasoline and two-
stroke oil. It is important to accurately measure the amount
of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
Gasoline, litre
Two-stroke oil, litre
2% (1:50)
0,10
5
10
0,43/0,20
0,30
15
WARNING! Always ensure there is
adequate ventilation when handling fuel.
!
20
0,40
US gallon
US fl. oz.
2 1/2
Gasoline
1
2 1/2
5
6 1/2
12 7/8
•
•
Use good quality unleaded gasoline.
Mixing
CAUTION! Engines equipped with catalytic
converters must be run on unleaded fuel mixtures.
•
Leaded gasoline will destroy the catalytic converter and
it will no longer serve its purpose.The green fuel cap on
saws fitted with catalytic converters means that only
unleaded gasoline can be used.
•
The lowest recommended octane grade is 87
((RON+MON)/2). If you run the engine on a lower octane
grade than 87 so-called knocking can occur. This gives
rise to a high engine temperature and increased bearing
load, which can result in serious engine damage.
•
•
Always mix the gasoline and oil in a clean container
intended for fuel.
•
When working with continuous high revs (e.g. limbing) a
higher octane is recommended.
Always start by filling half the amount of the gasoline to
be used. Then add the entire amount of oil. Mix (shake)
the fuel mixture. Add the remaining amount of gasoline.
Environment fuel
HUSQVARNA recommends the use of alkylate fuel or
environmental fuel for four-stroke engines blended with two-
stroke oil as set out below. Note that carburetor adjustment
may be necessary when changing the type of fuel (see
instructions under the heading Carburetor).
•
•
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
Do not mix more than one month’s supply of fuel at a
time.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Running-in
Avoid running at a too high speed for extended periods
during the first 10 hours.
Chain oil
Two-stroke oil
•
We recommend the use of special oil (chain oil) with
good adhesion characteristics.
•
•
•
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two stroke-engines.
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
Never use oil intended for four-stroke engines.
•
•
•
Never use waste oil. This results in damage to the oil
pump, the bar and the chain.
It is important to use oil of the right grade (suitable
viscosity range) to suit the air temperature.
In temperatures below 32°F (0°C) some oils become too
viscous. This can overload the oil pump and result in
damage to the oil pump components.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
•
Contact your service agent when choosing chain oil.
Fuel safety
Fueling
•
Never refuel the machine while the engine is running.
•
Make sure there is plenty of ventilation when refuelling or
mixing fuel (gasoline and 2-stroke oil).
•
Move the machine at least 10 ft (3 m) from the refuelling
point before starting it.
WARNING! Taking the following
precautions, will lessen the risk of fire:
!
Do not smoke and do not place any hot
objects in the vicinity of fuel.
Always stop the engine and let it cool for a
few minutes before refuelling.
Min. 3 m
(10 ft)
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
•
Never start the machine:
1
If you have spilled fuel or chain oil on the machine.Wipe
off the spillage and allow remaining fuel to evaporate.
Tighten the fuel cap carefully after
refuelling.
2
3
If you have spilled fuel on yourself or your clothes,
change your clothes. Wash any part of your body that
has come in contact with fuel. Use soap and water.
Always move the machine away from the
refuelling area before starting.
If the machine is leaking fuel. Check regularly for leaks
from the fuel cap and fuel lines.
Clean the area around the fuel cap. Clean the fuel and chain
oil tanks regularly. The fuel filter must be replaced at least
once a year. Contamination in the tanks causes malfunction.
Make sure the fuel is well mixed by shaking the container
before refuelling.The capacities of the chain oil tank and fuel
tank are carefully matched.You should therefore always fill
the chain oil tank and fuel tank at the same time.
WARNING! Never use a machine with
visible damage to the spark plug guard and
ignition cable. A risk of sparking arises,
which can cause a fire.
Transport and storage
•
Always store the chain saw and fuel so that there is no
risk of leakages or fumes coming into contact with sparks
or naked flames from electrical equipment, electric
motors, relays/switches, boilers and the like.
•
•
Always store fuel in an approved container designed for
that purpose.
WARNING! Fuel and fuel vapor are highly
flammable.Take care when handling fuel
and chain oil. Be aware of the risks of fire,
explosion and those associated with
inhalation.
For longer periods of storage or for transport of the chain
saw, the fuel and chain oil tanks should be emptied. Ask
where you can dispose of waste fuel and chain oil at your
local gas station.
!
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
The bar guard must always be fitted to the cutting
attachment when the machine is being transported or in
storage, in order to prevent accident contact with the
sharp chain. Even a non-moving chain can cause
serious cuts to yourself or persons you bump into with an
exposed chain.
Long-term storage
Empty the fuel/oil tanks in a well ventilated area. Store the
fuel in approved cans in a safe place. Fit the bar guard.
Clean the machine. See instructions under the heading
Maintenance schedule.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
started the valve will automatically return to its original
setting.
Starting and stopping
WARNING! Note the following before
starting:
A
B
!
The chain brake must be engaged when the
chain saw is started to reduce the chance
of contact with the moving chain during
starting.
Never start a chain saw unless the bar,
chain and all covers are fitted correctly.
Otherwise the clutch can come loose and
cause personal injuries.
Warm engine
Use the same procedure as for starting a cold engine but
without setting the choke control in the choke position. The
correct choke/start throttle setting is obtained by moving the
choke control to the choke position and then pushing it in
again.
Place the machine on firm ground. Make
sure you have a secure footing and that the
chain cannot touch anything.
Keep people and animals well away from
the working area.
Cold engine
Starting:The chain brake should be activated when starting
the chain saw. Activate the chain brake by pushing the front
hand guard forwards.
Starting
Grip the front handle with your left hand. Hold the chain saw
on the ground by placing your right foot through the rear
handle. Pull the starter handle with your right hand and pull
out the starter cord slowly until you feel a resistance (as the
starter pawls engage) then pull firmly and rapidly. Never
wrap the starter cord around your hand
Ignition; choke: Set the choke control in the choke position.
This should automatically set the stop switch to the start
position.
Start throttle: The correct choke/start throttle setting is
obtained by moving the control to the choke position.
CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully
extended. This can damage the machine.
If the machine is fitted with an air purge (A): Press the air
purge repeatedly until fuel begins to fill the bulb. The bulb
need not be completely filled.
Push in the choke control as soon as the engine fires and
make repeated starting attempts. Immediately press and
release the throttle when the engine starts. That will
disengage the throttle latch.
If the machine is fitted with a decompression valve (B):Press
the valve to reduce the pressure in the cylinder and make
starting easier.You should always use the decompression
valve when starting the machine. Once the machine has
As the chain brake is still activated the engine must return to
idling speed as soon as possible by disengaging the throttle
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
latch in order to avoid unnecessery wear on the clutch
•
Observe your surroundings and make sure that there is
assembly.
no risk of people or animals coming into contact with the
cutting equipment.
Note! Pull the front hand guard towards the front handle.The
chain brake is now disengaged.Your saw is ready for use.
•
Always hold the saw with both hands. The right hand
should be on the rear handle, and the left hand on the
front handle. All people, whether right or left handed,
should use this grip. Use a firm grip with thumbs and
fingers encircling the chain saw handles.
WARNING! Long term inhalation of the
engine’s exhaust fumes, chain oil mist and
dust from sawdust can represent a health
risk.
!
•
Never start a chain saw unless the bar, chain and all
covers are fitted correctly. See instructions under the
heading Assembly. Without a bar and chain attached to
the chain saw the clutch can come loose and cause
serious injury.
Stopping
•
The chain brake should be activated when starting. Se
instructions under the heading Start and stop. Do not
drop start. This method is very dangerous because you
may lose control of the saw.
The engine is stopped by pushing the stop switch to the stop
position.
•
Never start the machine indoors. Exhaust fumes can be
dangerous if inhaled.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Basic safety rules
Before use:
1
•
Look around you:
6
5
To ensure that people, animals or other things cannot
affect your control of the machine.
7
4
3
•
To make sure that none of the above might come within
reach of your saw or be injured by falling trees.
8
10
2
9
1
1
Check that the chain brake works correctly and is not
damaged.
2
3
Check that the rear right hand guard is not damaged.
Check that the throttle lockout works correctly and is not
damaged.
CAUTION! Follow the instructions above, but do not use a
chain saw in a situation where you cannot call for help in
case of an accident.
4
Check that the stop switch works correctly and is not
damaged.
2
Do not use the machine in bad weather, such as dense
fog, heavy rain, strong wind, intense cold, etc.Working in
bad weather is tiring and often brings added risks, such
as icy ground, unpredictable felling direction, etc.
5
6
Check that all handles are free from oil.
Check that the anti vibration system works and is not
damaged.
7
8
9
Check that the muffler is securely attached and not
damaged.
3
Take great care when removing small branches and
avoid cutting bushes (i.e. cutting many small branches at
the same time). Small branches can be grabbed by the
chain and thrown back at you, causing serious injury.
Check that all parts of the chain saw are tightened
correctly and that they are not damaged or missing.
Check that the chain catcher is in place and not
damaged. Replace it if necessary with an aluminium
chain catcher (is available as spare part).
10 Check the chain tension.
General working instructions
4
Make sure you can move and stand safely. Check the
area around you for possible obstacles (roots, rocks,
branches, ditches, etc.) in case you have to move
suddenly. Take great care when working on sloping
ground.
IMPORTANT!
This section describes basic safety rules for using a chain
saw. This information is never a substitute for professional
skills and experience. If you get into a situation where you
feel unsafe, stop and seek expert advice. Contact your
chain saw dealer, service agent or an experienced chain
saw user.Do not attempt any task that you are not sure you
can handle!
Before using a chain saw you must understand the effects
of kickback and how to avoid them. See instructions under
the heading How to avoid kickback.
Before using a chain saw you must understand the
difference between cutting with the top and bottom edges
of the bar. See instructions under the headings How to
avoid kickback and Machine’s safety equipment.
5
Take great care when cutting a tree that is under tension.
A tree that is under tension may spring back to its normal
position before or after being cut. If you position yourself
incorrectly or make the cut in the wrong place the tree
may hit you or the machine and cause you to lose control.
Both situations can cause serious personal injury.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Have control over the workpiece. If the pieces you intend
to cut are small and light, they can jam in the saw chain
and be thrown towards you. Even if this does not need to
be a danger, you may be surprised and lose control of the
saw. Never saw stacked logs or branches without first
separating them.Only saw one log or one piece at a time.
Remove the cut pieces to keep your working area safe.
6
Before moving your chain saw switch off the engine and
lock the chain using the chain brake. Carry the chain saw
with the bar and chain pointing backwards. Fit a guard to
the bar before transporting the chain saw or carrying it for
any distance.
4
Never use the chain saw above shoulder height and
avoid cutting with the tip of the bar. Never use the
chain saw one-handed!
Never carry or hang the saw by the trigger! This could
damage the mechanism and disable the chain brake.
7
When you put the chain saw on the ground, lock the saw
chain using the chain brake and ensure you have a
constant view of the machine. Switch the engine off
before leaving your chain saw for any length of time.
5
In order to keep control of your saw, always maintain a
firm foothold. Never work on a ladder, in a tree or on any
other insecure support.
General rules
1
If you understand what kickback is and how it happens
then you can reduce or eliminate the element of surprise.
By being prepared you reduce the risk. Kickback is
usually quite mild, but it can sometimes be very sudden
and violent.
2
Always hold the chain saw firmly with your right hand on
the rear handle and your left hand on the front handle.
Wrap your fingers and thumbs around the handles.You
should use this grip whether you are right-handed or left-
handed. This grip minimizes the effect of kickback and
lets you keep the chain saw under control.Do not let go
of the handles!
6
7
Always use a fast cutting speed, i.e. full throttle.
Take great care when you cut with the top edge of the bar,
i.e. when cutting from the underside of the object.This is
known as cutting with a pushing chain.The chain tries to
push the chain saw back towards the user. If the saw
chain is jamming, the saw may be pushed back at you.
3
Most kickback accidents happen during limbing. Make
sure you are standing firmly and that there is nothing in
the way that might make you trip or lose your balance.
Lack of concentration can lead to kickback if the kickback
zone of the bar accidentally touches a branch, nearby
tree or some other object.
8
Unless the user resists this pushing force there is a risk
that the chain saw will move so far backwards that only
the kickback zone of the bar is in contact with the tree,
which can lead to a kickback.
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Cutting with the bottom edge of the bar, i.e. from the top
3
Make sure the chain will not strike the ground or any
of the object downwards, is known as cutting with a
pulling chain. In this case the chain saw pulls itself
towards the tree and the front edge of the chain saw body
rests naturally on the trunk when cutting. Cutting with a
pulling chain gives the operator better control over the
chain saw and the position of the kickback zone.
other object during or after cutting.
4
Is there a risk of kickback?
9
Follow the instructions on sharpening and maintaining
your bar and chain.When you replace the bar and chain
use only combinations that are recommended by us.See
instructions under the headings Cutting equipment and
Technical data.
5
Do the conditions and surrounding terrain affect how
safely you can stand and move about?
Basic cutting technique
Two factors decide whether the chain will jam or the object
that you are cutting will split: the first is how the object is
supported before and after cutting, and the second is
whether it is in tension.
WARNING! Never use a chain saw by
holding it with one hand. A chain saw is not
safely controlled with one hand. Always
have a secure, firm grip around the handles
with both hands.
!
In most cases you can avoid these problems by cutting in two
stages; from the top and from the bottom.You need to
support the object so that it will not trap the chain or split
during cutting.
General
IMPORTANT! If the chain jams in the cut: stop the engine!
Don’t try to pull the chain saw free. If you do you may be
injured by the chain when the chain saw suddenly breaks
free. Use a lever to open up the cut and free the chain saw.
•
•
Always use full throttle when cutting!
Reduce the speed to idle after every cut (running the
engine for too long at full throttle without any load, i.e.
without any resistance from the chain during cutting, can
lead to serious engine damage).
The following instructions describe how to handle the
common situations you are likely to encounter when using a
chain saw.
•
•
Cutting from above = Cutting with a pulling chain.
Cutting from below = Cutting with pushing chain.
Cutting with a pushing chain increases the risk of kickback.
See instructions under the heading How to avoid kickback.
Limbing
When limbing thick branches you should use the same
approach as for cutting.
Terms
Cutting = General term for cutting through wood.
Limbing = Cutting branches off a felled tree.
Cut difficult branches piece by piece.
2
1
Splitting = When the object you are cutting breaks off before
the cut is complete.
3
There are five important factors you should consider
before making a cut:
1
Make sure the cutting equipment will not jam in the cut.
2
Make sure the object you are cutting will not split.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Cutting
Turn the log and finish the cut from the opposite side.
WARNING! Never attempt to cut logs while
they are in a pile or when a couple of logs
are lying together. Such procedures
drastically increase the risk of kickback
which can result in a serious or fatal injury.
!
The log is supported at one end. There is a high risk that
it will split.
If you have a pile of logs, each log you attempt to cut should
be removed from the pile, placed on a saw horse or runners
and cut individually.
Remove the cut pieces from the cutting area. By leaving
them in the cutting area, you increase the risk for
inadvertently getting a kickback, as well as increasing the
risk of losing your balance while working.
Start by cutting from below (about 1/3 of the way through).
Finish by cutting from above so that the two cuts meet.
The log is supported at both ends. There is a high risk that
the chain will jam.
The log is lying on the ground. There is little risk of the
chain jamming or the object splitting. However there is a risk
that the chain will touch the ground when you finish the cut.
Start by cutting from above (about 1/3 of the way through).
Cut all the way through the log from above. Avoid letting the
chain touch the ground as you finish the cut. Maintain full
throttle but be prepared for what might happen.
Finish by cutting from below so that the two cuts meet.
If it is possible (can you turn the log?) stop cutting about 2/3
of the way through the log.
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
is high accident risk. See instructions under the heading
Freeing a tree that has fallen badly.
Tree felling technique
IMPORTANT! It takes a lot of experience to fell a tree.
Inexperienced users of chain saws should not fell trees. Do
not attempt any task beyond your experience level!
Safe distance
The safe distance between a tree that is to be felled and
anyone else working nearby is at least 2 1/2 tree lengths.
Make sure that no-one else is in this ”risk zone” before or
during felling.
IMPORTANT! During critical felling operations, hearing
protectors should be lifted immediately when sawing is
completed so that sounds and warning signals can be
heard.
Clearing the trunk and preparing your retreat
Delimb the stem up to shoulder height. It is safer to work
from the top down and to have the tree between you and the
saw.
Felling direction
The aim is to fell the tree in a position where you can limb
and cross-cut the log as easily as possible.You want it to fall
in a location where you can stand and move about safely.
Once you have decided which way you want the tree to fall
you must judge which way the tree would fall naturally.
Several factors affect this:
•
•
•
•
•
•
Lean of the tree
Bend
Wind direction
Arrangement of branches
Weight of snow
Remove any undergrowth from the base of the tree and
check the area for obstacles (stones, branches, holes, etc.)
so that you have a clear path of retreat when the tree starts
to fall.Your path of retreat should be roughly 135 degrees
away from the intended felling direction.
Obstacles within the reach of the tree: for example, other
trees, power lines, roads and buildings.
•
Look for signs of damage and rot in the stem, this makes
it more probably that the tree will break and start to fall
before you expect it to.
Danger zone
tion
irec
g d
ellin
F
Retreat path
Danger zone
ne
er zo
g
an
D
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to
make it fall in the direction you first intended.
Another very important factor, which does not affect the
felling direction but does affect your safety, is to make sure
the tree has no damaged or dead branches that might break
off and hit you during felling.
The main point to avoid is letting the tree fall onto another
tree. It is very dangerous to remove a trapped tree and there
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Felling
Felling cut
The felling cut is made from the opposite side of the tree and
it must be perfectly horizontal. Stand on the left side of the
tree and cut on the pull stroke.
WARNING! Unless you have special
training we advise you not to fell trees with
a diameter larger than the bar length of your
saw!
!
Make the felling cut about 1.5-2 inches (3-5 cm) above the
bottom directional cut.
Felling is done using three cuts. First you make the
directional cuts, which consist of the top cut and the bottom
cut, then you finish with the felling cut. By placing these cuts
correctly you can control the felling direction very accurately.
Directional cuts
To make the directional cut you begin with the top cut. Aim
using to the saw’s felling direction mark (1) toward a goal
further forward in the terrain, where you would like the tree to
fall (2). Stand on the right-hand side of the tree, behind the
saw, and cut with a pull stroke.
Finish the felling cut parallel with the directional cut line so
that the distance between them is at least 1/10 of the trunk
diameter. The uncut section of the trunk is called the felling
hinge.
Next make the bottom cut so that it finishes exactly at the end
of the top cut.
The felling hinge controls the direction that the tree falls in.
The directional cuts should run 1/4 of the diameter through
the trunk and the angle between the top cut and bottom cut
should be 45°.
All control over the felling direction is lost if the felling hinge
is too narrow or non-existent, or if the directional cuts and
felling cut are badly placed.
The line where the two cuts meet is called the directional cut
line. This line should be perfectly horizontal and at right
angles (90°) to the chosen felling direction.
When the felling cut and directional cut are complete the tree
should start to fall by itself or with the aid of a felling wedge
or breaking bar.
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
We recommend that you use a bar that is longer than the
diameter of the tree, so that you can make the felling cut and
directional cuts with single cutting strokes. See instructions
under the heading Technical data section to find out which
lengths of bar are recommended for your saw.
•
Portable
Cutting trees and branches that are in tension
Preparations: Work out which side is in tension and where
the point of maximum tension is (i.e. where it would break if
it was bent even more).
There are methods for felling trees with a diameter larger
than the bar length. However these methods involve a much
greater risk that the kickback zone of the bar will come into
contact with the tree.
Decide which is the safest way to release the tension and
whether you are able to do it safely. In complicated situations
the only safe method is to put aside your chain saw and use
a winch.
General advice:
Freeing a tree that has fallen badly
Position yourself so that you will be clear of the tree or branch
when the tension is released.
Freeing a ”trapped tree”
It is very dangerous to remove a trapped tree and there is
high accident risk.
Never try to fell the tree that is trapped.
Make one or more cuts at or near the point of maximum
tension. Make as many cuts of sufficient depth as necessary
to reduce the tension and make the tree or branch break at
the point of maximum tension.
Never cut straight through a tree or branch that is in
tension!
If you must cut across tree/limb, make two to three cuts, one
inch apart, one to two inches deep.
Never work in the risk zone of the hanging trapped tree.
Continue to cut deeper until tree/limb bends and tension is
released.
The safest method is to use a winch.
Tractor-mounted
Cut tree/limb from outside the bend, after tension has been
released.
•
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Limbing
How to avoid kickback
WARNING! A majority of kickback
WARNING! Kickback can happen very
accidents occur during limbing. Do not use
the kickback zone of the guide bar. Be
extremely cautious and avoid contacting
the log, other limbs or objects with the nose
of the guide bar. Be extremely cautious of
limbs under tension.They can spring back
toward you and cause loss of control
resulting in injury.
!
suddenly and violently; kicking the chain
saw, bar and chain back at the user. If this
happens when the chain is moving it can
cause very serious, even fatal injuries. It is
vital you understand what causes kickback
and that you can avoid it by taking care and
using the right working technique.
!
What is kickback?
Make sure that you can stand and move about safely. Work
on the left side of the trunk.Work as close as possible to the
chain saw for maximum control. If possible, let the weight of
the chain saw rest on the trunk.
The word kickback is used to describe the sudden reaction
that causes the chain saw and bar to jump off an object when
the upper quadrant of the tip of the bar, known as the
kickback zone, touches an object.
Kickback always occurs in the cutting plane of the bar.
Normally the chain saw and bar are thrown backwards and
upwards towards the user. However, the chain saw may
move in a different direction depending on the way it was
being used when the kickback zone of the bar touched the
object.
Keep the trunk between you and the chain saw as you move
along the trunk.
Cutting the trunk into logs
See instructions under the heading Basic cutting technique.
Kickback only occurs if the kickback zone of the bar touches
an object.
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
lean mixture gives a higher engine speed and a rich
mixture gives a lower engine speed.
General
The user must only carry out the maintenance and service
work described in this manual.
•
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
IMPORTANT! Any maintenance other than that described
in this manual must be carried out by your servicing dealer
(retailer).
Basic settings and running in
The basic carburetor settings are adjusted during testing at
the factory. Avoid running at a too high speed for extended
periods during the first 10 hours.
Carburetor adjustment
CAUTION! If the chain rotates while idling the T-screw
must be turned anti-clockwise until the chain stops.
Due to existing environmental and emissions legislation your
chain saw is equipped with movement limiters on the
carburetor adjuster screws. These limit the adjustment
possibilities to a maximum of a 1/2 turn.
Rec. idle speed: 2700 rpm
Fine adjustment
H
L
When the machine has been ”run-in” the carburetor should
be finely adjusted. The fine adjustment should be carried
out by a qualified person. First adjust the L-jet, then the
idling screw T and then the H-jet.
1/2
1/2
Conditions
•
Before any adjustments are made the air filter should be
clean and the cylinder cover fitted. Adjusting the
carburetor while a dirty air filter is in use will result in a
leaner mixture next time the filter is cleaned. This can
give rise to serious engine damage.
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
Function
•
•
•
Do not attempt to adjust the L and H jets beyond
either stop as this could cause damage.
•
The carburetor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the carburetor.
The air/fuel mixture is adjustable. Correct adjustment is
essential to get the best performance from the machine.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
Place the machine on a flat surface so that the bar points
away from you and so that the bar and chain do not come
into contact with the surface or other objects.
•
The satisfactory operation of a catalytic converter
depends, among other factors, on the correct adjustment
of the carburetor. Carefully follow the instructions below,
using a tachometer as an aid.
Low speed jet L
•
•
The setting of the carburetor means that the engine is
adapted to local conditions, for example, the climate,
altitude, fuel and the type of 2-stroke oil.
Turn the low speed jet L clockwise until it stops. If the engine
accelerates poorly or idles unevenly, turn the low speed jet L
anticlockwise until good acceleration and idling are
achieved.
The carburetor has three adjustment controls:
- L = Low speed jet
Fine adjustment of the idling speedT
- H = High speed jet
Adjust the idle speed with the T-screw. If it is necessary to re-
adjust, turn the T-screw clockwise while the engine is
running, until the chain starts to rotate. Then turn counter-
clockwise until the chain stops. A correctly adjusted idle
speed setting occurs when the engine runs smoothly in
every position. It should also be good margin to the rpm
when the chain starts to rotate.
- T = Idle adjustment screw
L
H
WARNING! Contact your servicing dealer, if
the idle speed setting cannot be adjusted
!
T
so that the chain stops at idle. Do not use
the chain saw until it has been properly
adjusted or repaired.
•
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled
with the throttle.If they are screwed clockwise the air/fuel
ratio becomes leaner (less fuel) and if they are turned
anti-clockwise the ratio becomes richer (more fuel). A
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checking the front hand guard
High speed jet H
At the factory the engine is adjusted at sea level. When
working at a high altitude or in different weather
conditions, temperatures and atmospheric humidity, it
may be necessary to make minor adjustments to the
high speed jet.
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
CAUTION! If the high speed jet is screwed in too far, it
may damage the piston/cylinder.
When test run at the factory, the high speed jet is set so that
the engine satisfies the applicable legal requirements at the
same time as achieving maximum performance. The
carburetor’s high speed jet is then locked using a limiter cap
in the fully screwed out position. The limiter cap limits the
potential to adjust the high speed jet to at most half a turn.
Move the front hand guard forwards and back to make sure
it moves freely and that it is securely anchored to the clutch
cover.
Correctly adjusted carburetor
When the carburetor is correctly adjusted the machine
accelerates without hesitation and the machine 4-cycles a
little at max. speed. It is also important that the chain does
not rotate at idle. If the L-jet is set too lean it may cause
starting difficulties and poor acceleration. If the H-jet is set
too lean the machine will have less power, poor acceleration
and could suffer damage to the engine.
Checking the inertia brake release
Checking, maintaining and
servicing chain saw safety
equipment
With the engine turned off, hold the chain saw over a stump
or other firm object. Let go of the front handle so that the bar
drops towards the stump as the chain saw rotates around the
rear handle.
Note! All servicing and repair work on the machine requires
special training. This is especially true of the machine′s
safety equipment. If your machine fails any of the checks
described below we recommend you to contact our
servicing dealer.
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain brake
and clutch drum. Dirt and wear can impair operation of the
brake.
When the bar hits the stump the brake should be
applied.
Regularly check that the brake band is at least 0.024 inch
(0.6 mm) thick at its thinnest point.
32 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checking the right-hand brake trigger
Throttle lockout
Check that the right hand guard is not damaged and that
there are no visible defects, such as cracks.
•
•
•
•
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Push the trigger up and forwards to check that it moves freely
and is securely hinged to the clutch cover.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Never carry or hang the saw by the trigger! This could
damage the mechanism and disable the chain brake.
Check that the throttle control and throttle lockout move
freely and that the return springs work properly.
Checking the brake trigger
Place the chain saw on firm ground and start it. Make sure
the chain does not touch the ground or any other object. See
the instructions under the heading Start and stop.
Start the chain saw and apply full throttle. Release the
throttle control and check that the chain stops and
remains stationary. If the chain rotates when the throttle
control is in the idle position you should check the
carburetor idle adjustment.
Chain catcher
Check that the chain catcher is not damaged and is firmly
attached to the body of the chain saw. Replace it if
necessary with an aluminium chain catcher (is available as
spare part).
Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles.
Apply full throttle and activate the chain brake by tilting your
left wrist forward onto the front hand guard. Do not let go of
the front handle. The chain should stop immediately.
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Muffler
Right hand guard
Check that the right hand guard is not damaged and that
there are no visible defects, such as cracks.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to the
machine.
Vibration damping system
Regularly check the vibration damping units for cracks or
deformation.
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you should
clean the screen at least once a week.This is best done with
a wire brush. A blocked screen will cause the engine to
overheat and may lead to serious damage.
Make sure the vibration damping units are securely attached
to the engine unit and handle unit.
Note! The screen must be replaced if it is damaged. If the
screen is blocked the machine will overheat and this will
cause damage to the cylinder and piston. Never use a
machine with a muffler that is in poor condition.Never use a
muffler if the spark arrestor screen is missing or
defective.
Stop switch
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible material.
A muffler equipped with a catalytic converter significantly
reduces the amount of hydrocarbons (HC), nitrogen oxides
(NO) and aldehydes in the exhaust fumes.Carbon monoxide
(CO), which is poisonous and odorless, is not however
reduced! Consequently, never work in an enclosed or badly
ventilated area. Good air circulation should always prevail
when working in snowy hollows, ravines or in confined
conditions.
34 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
starter housing and the starter handle. Tie a good knot
on the starter cord.
Starter
WARNING!When the recoil spring is wound
up in the starter housing it is under tension
and can, if handled carelessly, pop out and
cause personal injury.
!
Care must be exercised when replacing the
return spring, starter cord or the drive disc
spring. Wear protective glasses and
protective gloves.
Changing a broken or worn starter cord
346XP, 353:
•
Loosen the screws that hold the starter against the
crankcase and remove the starter.
•
Undo the screw in the centre of the pulley and remove
the pulley. Insert and fasten a new starter cord to the
pulley. Wind approx. 3 turns of the starter cord onto the
pulley. Connect the pulley to the recoil spring so that the
end of the spring engages in the pulley. Fit the screw in
the center of the pulley. Insert the starter cord through
the hole in the starter housing and the starter handle.
Make a secure knot in the end of the starter cord.
•
Pull out the cord approx. 30 cm (12 inches) and hook it
into the notch in the rim of the pulley. Release the recoil
spring by letting the pulley rotate slowly backwards.
Tensioning the recoil spring
•
Hook the starter cord in the notch in the pulley and turn
the starter pulley about 2 turns clockwise.
345e:
Undo the bolt in the centre of the pulley and remove the
•
Note! Check that the pulley can be turned an additional
1/2 turn when the starter cord is pulled all the way out.
drive disc, drive disc spring and the pulley. Insert and
secure a new starter cord in the starter pulley. Wind
approx. 3 turns of the starter cord on the starter pulley.
Fit the starter pulley so that the end of the recoil spring
hooks into the starter pulley. Now assemble the drive
disc spring, drive disc and the bolt in the centre of the
pulley. Carry the starter cord through the hole in the
English – 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Replacement of broken recoil and drive
disc springs
Air filter
The air filter must be regularly cleaned to remove dust and
dirt in order to avoid:
Recoil spring (A)
•
•
•
•
•
•
Carburettor malfunctions
Starting problems
•
Lift up the starter pulley. See instructions under the
heading Changing a broken or worn starter cord.
Remember that the recoil spring is coiled under tension
in the starter housing.
Loss of engine power
Unnecessary wear to engine parts
Excessive fuel consumption.
•
•
Remove the cassette with the recoil spring from the
starter.
Remove the air filter after taking off the air filter cover.
When refitting make sure that the air filter seals tightly
against the filter holder. Clean the filter by brushing or
shaking it.
Lubricate the recoil spring with light oil. Fit the cassette
with recoil spring in the starter. Fit the starter pulley and
tension the recoil spring.
Drive disc spring (B)
345e:
•
Undo the bolt in the centre of the pulley and remove the
drive disc and the drive disc spring.
•
Replace the drive disc spring and fit the drive disc above
the spring.
The filter can be cleaned more thoroughly by washing it in
water and detergent.
An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals. A damaged air filter
must always be replaced.
A
A
A HUSQVARNA chain saw can be equipped with different
types of air filters according to working conditions, weather,
season, etc. Contact your dealer for advice.
B
Spark plug
346XP, 353
345e
Fitting the starter
The spark plug condition is influenced by:
•
To fit the starter, first pull out the starter cord and place
the starter in position against the crankcase.Then slowly
release the starter cord so that the pulley engages with
the pawls.
•
•
Incorrect carburetor adjustment.
An incorrect fuel mixture (too much or incorrect type of
oil).
•
Fit and tighten the screws that hold the starter.
•
A dirty air filter.
These factors cause deposits on the spark plug electrodes,
which may result in operating problems and starting
difficulties.
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action.If the spark plug is dirty, clean it and check
that the electrode gap is 0.020 inch (0.5 mm).The spark plug
36 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
should be replaced after about a month in operation or
earlier if necessary.
machine is supplied from the factory with the screw set to
position 2. Turning the screw clockwise will reduce the oil
flow and turning the screw anti-clockwise will increase the oil
flow.
Note! Always use the recommended spark plug type! Use of
the wrong spark plug can damage the piston/cylinder.Check
that the spark plug is fitted with a suppressor.
+ –
1
2
3
Lubricating the bar tip sprocket
Recommended settings:
Bar 13"-15": Position 1
Bar 15"-18": Position 2
Bar 18"-20": Position 3
Lubricate the bar tip sprocket each time you refuel. Use the
special grease gun and a good quality bearing grease.
WARNING! The engine must be stopped
when making adjustments.
!
Cooling system
Needle bearing lubrication
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The clutch drum has a needle bearing on the output shaft.
This needle bearing must be lubricated regularly (once a
week).
The cooling system consists of:
1
2
3
4
5
Air intake on the starter.
Air guide plate.
When lubricating, remove the clutch cover by loosening the
two bar nuts. Lay the saw on its side with the clutch drum
upwards.
Fins on the flywheel.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
Lubrication involves engine oil dripping into the centre of the
clutch drum as it rotates.
5
4
3
2
1
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Adjustment of the oil pump
Note! The cooling system on a chain saw with catalytic
converter must be cleaned daily. This is particularly
important on chain saws with catalytic converters, because
the higher exhaust temperature requires efficient cooling of
the engine and the catalytic converter unit.
(346XP/353)
The oil pump is adjustable.Adjustments are made by turning
the screw using a screwdriver or combination spanner. The
English – 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
•
•
Partly mask the air inlet on the starter to increase the
working temperature of the engine.
”Air Injection” centrifugal cleaning
Centrifugal cleaning means the following: All air to the
carburetor passes through the starter. Dirt and dust is
pushed out by the cooling fan.
Preheat the intake air to the carburetor by using the heat
from the cylinder.
°
°
Temperature 0 C (32 F) or colder:
A special winter kit, including necessary parts and assembly
instructions, is available for using the machine in cold
temperatures.
345e: Before usage a hole is made in the cylinder cover and
a winter flap is fitted (see illustration below).
346XP, 353: The cylinder cover is designed so it can be
IMPORTANT! In order to maintain operation of the
centrifugal cleaning system it must be regularly maintained.
Clean the air intake to the starter, the fins on the flywheel, the
space around the flywheel, inlet pipe and carburetor
compartment.
adjusted for running in cold weather.
Twist the winter flap so that preheated air from the cylinder
can pass into the carburetor space preventing icing of the air
filter, etc.
Heated handles
(346XPG, 353G)
On models with the model code XPG/G both the front handle
bar and the rear handle are equipped with electrical heating
coils. These are supplied with electricity from a generator
built into the chain saw.
For temperatures below -5°C (23°F) and/or in snow
conditions there is also:
•
•
a special cover (A) for the starter housing
a winter plug (B) for the air nozzle that is fitted as shown.
When the switch is pushed upwards, the heat is switched on.
When the switch is pushed downwards, the heat is switched
off.
Electrical carburetor heating
(346XPG, 353G)
These reduce the flow of cooling air and prevent large
amounts of snow from being sucked into the carburetor
space.
If this chain saw is marked with Carburetor Heating then it is
equipped with an electrically heated carburettor. The
electrical heating prevents icing in the carburettor. A
thermostat regulates heating so that the carburettor always
has the correct working temperature.
For further information see assembly instructions for the
winter kit.
CAUTION! When the winter plug is fitted the winter flap must
be open!
Winter use
Running problems can occur when using the machine in the
cold and snowy conditions caused by:
IMPORTANT! If the temperature rises above -5°C (23°F) or
0°C (32°F) respectively the machine MUST be restored to
its normal set-up. Otherwise there is a risk of overheating,
which can cause severe engine damage.
•
•
Too low engine temperature.
Icing of the air filter and carburetor.
Special measures are therefore often required:
38 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section.
Daily maintenance
Weekly maintenance
Monthly maintenance
Check the brake band on the chain
brake for wear. Replace when less than
0.024 inch (0.6 mm) remains at the
most worn point.
On chain saws without a catalytic
converter, check the cooling system
weekly.
Clean the outside of the machine.
Check that the components of the
throttle control work safely. (Throttle
lockout and throttle control.)
Check the starter, starter cord and
return spring.
Check the clutch centre, clutch drum
and clutch spring for wear.
Clean the chain brake and check that it
operates safely. Make sure that the
chain catcher is undamaged, and
replace it if necessary with an
aluminium chain catcher (is available as
spare part).
Check that the vibration damping
elements are not damaged.
Clean the spark plug. Check that the
electrode gap is 0.020 inch (0.5 mm).
The bar should be turned daily for more
even wear. Check the lubrication hole in
the bar, to be sure it is not clogged.
Clean the bar groove. If the bar has a
sprocket tip, this should be lubricated.
Lubricate the clutch drum bearing.
Clean the outside of the carburetor.
Check that the bar and chain are getting File off any burrs from the edges of the Check fuel hose for cracks or other
sufficient oil.
bar.
damage. Change if necessary.
Check the saw chain with regard to
visible cracks in the rivets and links,
whether the saw chain is stiff or whether
the rivets and links are abnormally
worn. Replace if necessary.
Clean or replace the spark arrestor
screen on the muffler.
Empty the fuel tank and clean the
inside.
Sharpen the chain and check its tension
and condition. Check the drive sprocket
for excessive wear and replace if
necessary.
Clean the carburetor compartment.
Empty the oil tank and clean the inside.
Check all cables and connections.
Clean the air filter. Replace if
necessary.
Clean the starter units air intake.
Clean the area under the cover for the
right-hand brake.
Check that nuts and screws are tight.
Check that the stop switch works
correctly.
Check that there are no fuel leaks from
the engine, tank or fuel lines.
On chain saws with a catalytic
converter, check the cooling system
daily.
Make sure the mechanism for the right-
hand brake operates smoothly.
English – 39
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
345e TrioBrake
346XP TrioBrake
353 TrioBrake
Engine
Cylinder displacement, cu.in/cm3
Cylinder bore, inch/mm
Stroke, inch/mm
2,75/45,0
1,65/42
1,28/32,5
2700
3,06/50,1
1,74/44,3
1,28/32,5
2700
3,15/51,7
1,77/45
1,28/32,5
2700
Idle speed, rpm
Power, kW/ rpm
2,2/9000
2,7/9600
2,4/9000
Ignition system
Manufacturer of ignition system
Type of ignition system
SEM
SEM
CD
SEM
CD
CD
NGK BPMR 7A/
Champion RCJ 7Y RCJ 7Y
NGK BPMR 7A/ Champion NGK BPMR 7A/
Spark plug
Champion RCJ 7Y
Electrode gap, inch/mm
0,02/0,5
0,02/0,5
0,02/0,5
Fuel and lubrication system
Manufacturer of carburetor
Carburetor type
Zama
Zama
Zama
C3-EL 32
1,06/0,5
9
C3-EL 18B
1,06/0,5
5-12
C3-EL 18B
1,06/0,5
5-12
Fuel tank capacity, US pint/litre
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/litre
Type of oil pump
0,53/0,25
Automatic
0,59/0,28
Automatic
0,59/0,28
Automatic
Weight
Chain saw without bar or chain, empty tanks, lb/kg
11,0/5,0
346XP: 11,0/5,0
353: 11,0/5,0
346XPG: 11,2/5,1
353G: 11,2/5,1
353 E-tech: 11,0/
5,0
346XP E-tech: 11,0/5,0
346XPG E-tech: 11,2/5,1
353G E-tech: 11,2/
5,1
Chain/bar
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Pitch, inch/mm
13"/33
13"/33
13"/33
13-20"/33-50
12-19"/31-48
0,325/8,25
0,050/1,3
0,058/1,5
Spur/7
13-20"/33-50
12-19"/31-48
0,325/8,25
0,050/1,3
0,058/1,5
Rim/7
13-20"/33-50
12-19"/31-48
0,325/8,25
0,050/1,3
0,058/1,5
Rim/7
Thickness of drive links, inch/mm
Drive sprocket type/teeth
Chain speed at max. power, m/sec
17,3
18,5
17,3
40 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 345e TrioBrake, 346XP TrioBrake
and 353 TrioBrake. The combinations of power head, bar and chain have been investigated in accordance with the kickback
and vibration requirements of ANSI B 175.1–2000.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding
maximum nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will
also achieve kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For
guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth
may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a
sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
Bar and chain combinations
Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175.1 safety
requirements for gasoline powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in.
specified in ANSI 175.1.We recommend that you as a replacement use the listed chains or "Low kickback saw chains" which
are available at your dealer.
Bar
Chain
Drive link count
Length, inch
Pitch, inch
0,325
0,325
0,325
0,325
0,325
0,325
0,325
0,325
0,325
0,325
Gauge, inch
Max. nose radius
Type
13
15
16
18
20
13
15
16
18
20
10T
10T
10T
10T
10T
10T
10T
10T
10T
12T
56
64
66
72
78
56
64
66
72
78
1,3
1,5
Husqvarna H30
Husqvarna H25
Note: For the chains above you are free to choose between 0,050" and 0,058" gauge drive link for the corresponding bar, see
the table below.
0,050"/1,3 mm
0,058"/1,5 mm
H30
-
H22
H25
Saw chain filing and file gauges
English – 41
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
charge to the owner at an approved Husqvarna Forest & Garden
servicing dealer. If you have any questions regarding your
warranty rights and responsibilities, you should contact your
nearest authorized servicing dealer or call Husqvarna Forest &
YOUR WARRANTY RIGHTS AND
OBLIGATIONS
The EPA (The US Environmental Protection Agency),
Environment Canada and Husqvarna Forest & Garden are
pleased to explain the emissions control system warranty on
your 2009 and later small nonroad engine. In U.S. and
Canada, new small nonroad engines must be designed, built
and equipped to meet the federal stringent anti-smog
standards. Husqvarna Forest & Garden must warrant the
emission control system on your small nonroad engine for
the period of time listed below provided there has been no
abuse, neglect or improper maintenance of your unit.Your
emission control system includes Parts such as the
carburetor and the ignition system. Where a warrantable
condition exists, Husqvarna Forest & Garden will repair your
small nonroad engine at no cost to you. Expenses covered
under warranty include diagnosis, parts and labor.
WARRANTY PERIOD Any warranted part which is not
scheduled for replacement as required maintenance, or
which is scheduled only for regular inspection to the effect of
“repair or replace as necessary” shall be warranted for 2
years.Any warranted part which is scheduled for replacement
as required maintenance shall be warranted for the period of
time up to the first scheduled replacement point for that part.
DIAGNOSIS The owner shall not be charged for diagnostic
labor which leads to the determination that a warranted part
is defective, if the diagnostic work is performed at an
approved Husqvarna Forest & Garden servicing dealer.
CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden
may be liable for damages to other engine components
caused by the failure of a warranted part still under warranty.
′
MANUFACTURER S WARRANTY
COVERAGE
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
The 2009 and later small nonroad engines are warranted for
two years. If any emission related part on you engine (as
listed above) is defective, the part will be repaired or
replaced by Husqvarna Forest & Garden.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest & Garden is
not liable to cover failures of warranted parts caused by the
use of add-on or modified parts.
′
OWNER S WARRANTY RESPONSIBILITIES
As the small nonroad engine owner, you are responsible for
the performance of the required maintenance listed in your
Operator′s Manual. Husqvarna Forest & Garden recommends
that you retain all receipts covering maintenance on your small
nonroad engine, but Husqvarna Forest & Garden cannot deny
warranty solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance. As the
small nonroad engine owner, you should, however, be aware
that Husqvarna Forest & Garden may deny you warranty
coverage if your small nonroad engine or a part of it has failed
due to abuse, neglect, improper maintenance, unapproved
modifications or the use of parts not made or approved by the
original equipment manufacturer.You are responsible for
presenting your small nonroad engine to a Husqvarna Forest
& Garden authorized servicing dealer as soon as a problem
exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.If you have
any questions regarding your warranty rights and
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at 1-
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement part
used in the performance of any warranty maintenance or
repairs on emission-related parts, will be provided without
charge to the owner if the part is under warranty.
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at 1-800-
EMISSION CONTROL WARRANTY PARTS
LIST
1
2
3
Carburetor and internal parts
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date small nonroad
engine is delivered.
Intake pipe, airfilter holder and carburetor bolts.
Airfilter and fuelfilter covered up to maintenance
schedule.
LENGTH OF COVERAGE
4
5
6
Spark Plug, covered up to maintenance schedule
Ignition Module
Muffler with catalytic converter
Husqvarna Forest & Garden warrants to the initial owner and
each subsequent purchaser that the engine is free from
defects in materials and workmanship which cause the
failure of a warranted part for a period of two years.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or
replacement of any warranted part will be performed at no
´®z+RxQ¶5
´®z+RxQ¶5
42 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
AMERICAN STANDARD SAFETY PRECAUTIONS
Other safety precautions
Safety precautions for chain saw
users
(ANSI B 175.1-2000 Annex C)
WARNING! Do not operate a chain saw with
one hand! Serious injury to the operator,
helpers, bystanders or any combination of
these persons may result from one-handed
operation. A chain saw is intended for two-
handed use.
!
Kickback safety precautions
WARNING! Kickback may occur when the
nose or tip of the guide bar touches an
object, or when the wood closes in and
pinches the saw chain in the cut.
!
Do not operate a chain saw when you are fatigued.
Use safety footwear; snug-fitting clothing, protective gloves,
and eye, hearing and head protection devices.
Tip contact in some cases may cause a
lightning fast reverse reaction, kicking the
guide bar up and back towards the
operator.
Use caution when handling fuel. Move the chain saw at least
10 feet (3 m) from the fueling point before starting the
engine.
Do not allow other persons to be near the chain saw when
starting or cutting with the chain saw. Keep bystanders and
animals out of the work area.
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back towards the operator.
Do not start cutting until you have a clear work area, secure
footing and a planned retreat path from the falling tree.
Either of these reactions may cause you to
lose control of the saw which could result
in serious personal injury.
Keep all parts of your body away from the saw chain when
the engine is running.
Before you start the engine, make sure that the saw chain is
not contacting anything.
Do not rely exclusively upon the safety
devices built into your saw. As a chain saw
user, you should take several steps to keep
your cutting jobs free from accident or
injury.
Carry the chain saw with the engine stopped, the guide bar
and saw chain to the rear, and the muffler away from your
body.
Do not operate a chain saw that is damaged, improperly
adjusted, or not completely and securely assembled. Be
sure that the saw chain stops moving when the throttle
control trigger is released.
With a basic understanding of kickback, you can reduce or
eliminate the element of surprise. Sudden surprise
contributes to accidents.
Shut off the engine before setting the chain saw down.
Keep a good firm grip on the saw with both hands, the right
hand on the rear handle, and the left hand on the front
handle, when the engine is running. Use a firm grip with
thumbs and fingers encircling the chain saw handles. A firm
grip will help you reduce kickback and maintain control of the
saw. Don’t let go.
Use extreme caution when cutting small size brush and
saplings because slender material may catch the saw chain
and be whipped toward you or pull you off balance.
When cutting a limb that is under tension be alert for
springback so that you will not be struck when the tension in
the wood fibers is released.
Make sure that the area in which you are cutting is free from
obstacles. Do not let the nose of the guide bar contact a log,
branch, or any other obstacle which could be hit while you
are operating the saw.
Keep handles dry, clean and free of oil or fuel mixture.
Operate the chain saw only in well-ventilated areas.
Do not operate a chain saw in a tree unless you have been
specifically trained to do so.
Cut at high engine speeds.
Do not overreach or cut above shoulder height.
Do not operate a chain saw above shoulder height.
Follow manufacturer’s sharpening and maintenance
instructions for the saw chain.
All chain saw service, other than the items listed in the
operator’s/owner’s safety and maintenance instructions,
should be performed by competent chain saw service
personnel. (For example, if improper tools are used to
remove the flywheel or if an improper tool is used to hold the
flywheel in order to remove the clutch, structural damage to
the flywheel could occur and subsequently cause the
flywheel to burst.)
Only use replacement bars and chains specified by the
manufacturer or the equivalent.
When transporting your chain saw, use the appropriate
guide bar guard.
Note: This Annex is intended primarily for the consumer or
occasional user.
English – 43
Download from Www.Somanuals.com. All Manuals Search And Download.
1151438-95
´®z+SKy¶5n¨
´®z+SKy¶5n¨
2009-01-21
Download from Www.Somanuals.com. All Manuals Search And Download.
|
