41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting and Optional Accessories
Understanding Mounting
Hunter’s patented mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in
one of two ways, depending on your preference: Standard or Angle
mounting. e steps in this manual include instructions for both
mounting methods.
Standard Mounting hangs from
the ceiling by a downrod (included),
Considering Optional Accessories
recommended for ceilings 8 feet or higher
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
For ceilings higher than 8 feet, you
can purchase Hunter extension
downrods. All Hunter fans use sturdy
3/4” diameter pipe to assure stability
and wobble-free performance.
3
Angle Mounting recommended for a
vaulted or angled ceiling
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver
• Phillips-head screwdriver
• Wrench or pliers
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Check
for any shipping damage to the motor or fan blades. If one of the fan
blades was damaged in shipment, return all the blades for replacement.
Installing Multiple Fans?
4
If you are installing more than
one fan, keep the fan blades in
sets, as they were shipped.
If any parts are missing or damaged, contact your Hunter dealer or call
Hunter Technical Support Department at 888-830-1326.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
Hunter Fan Company
41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Ceiling Plate
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
Isolator
Ceiling
Plate
2-2. Your fan comes with four neoprene noise isolators (“Isolators”).
Position the isolators between the ceiling plate and ceiling by
inserting the raised areas on each isolator into the holes in the
ceiling plate.
Step 2-2
2-3. read the lead wires from the outlet box down through the hole
in the middle of the ceiling plate.
2-4. Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
Note: e isolators should be flush against the ceiling.
2-5. Place a flat washer on each of the two 3” screws and pass the
screws through the slotted holes in the ceiling plate into the pilot
holes you drilled.
5
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Steps 2-3 – 2-5
Flat Washer
3” Screw
For Angled Ceilings: Be sure to
orient the ceiling plate so that the
arrows printed on the ceiling plate are
pointing towards the ceiling peak.
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling and Hanging the Fan
Step 3-1
3-1. Insert the downrod through the canopy, canopy trim ring, and
adapter cover. Feed the wires from the fan through the downrod.
3-2. Using the provided allen wrench, loosen the allen head set screw
on the adapter to install the pipe and ball assembly. Note: When
the pipe and ball assembly is fully installed, 2-3 threads on the
pipe will still be visible; this is normal. Securely retighten the set
screw with the allen wrench.
Downrod
Canopy
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
Canopy
Trim Ring
Allen Head
Set Screw
Adapter
Cover
3-3. Raise the fan and place the hook on the ceiling plate through the
U-shaped hole in the rim.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Step 3-3
U-shaped
Hole
6
Hunter Fan Company
41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Wiring the Fan
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
4-1. Disconnect the power by turning off the circuit breakers to the
outlet box and associated wall switch location.
4-2. Decide how you want to set up the fan and light controls. You
can control the fan and/or lights together or separately using one
or two wall switches. Follow Step 4-3 OR Step 4-4, depending on
what you decide.
4-3. If you want to, you can control the fan and light separately using
two wall switches, connect the wires as follows: connect the green
ground wire to the ground wire, connect white wire to white wire,
connect black wire to black wire, and connect the black/white
wire from the fan to the wire for the wall switch.
Step 4-3
7
4-4. Alternatively, you can control both fan and light with one switch.
To do so connect the wires as follows: connect the green ground
wire to the ground wire, connect white wire to white wire,
connect the black and the black/white wire from the fan to the
black wire in the ceiling.
4-5. To connect the wires, hold the bare metal leads together and place
a wire nut over them, then twist clockwise until tight.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
4-6. Push all wires and wire nuts back through the ceiling plate hole
into the outlet box.
Wire Nut
Step 4-4
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Installing the Canopy and Canopy Trim Ring
Step 5-2
Ceiling Plate
5-1. Holding the canopy, raise the fan off the hook.
5-2. Align the slots in the canopy with the tabs on the ceiling plate.
5-3. Raise the canopy over the ceiling plate. Rotate the canopy
clockwise until the tabs on the ceiling plate totally engage with
the slots in the canopy.
5-4. Loosely assemble the three canopy screws into the canopy one at
a time. Once all three screws are in, tighten them.
Canopy Trim
Ring
Canopy
5-5. Using both hands, push the canopy trim ring up to the top of the
canopy. e canopy trim ring will snap and lock into place.
Should you need to remove the canopy
trim ring, follow these steps:
1. Locate the tab indicators, small
bumps on top of tabs.
2. Press firmly on opposite sides of the
ring towards the canopy. e tabs
will flex out releasing the trim ring
from the canopy.
8
Step 5-3
Steps 5-4 – 5-5
Canopy
Screw
Hunter Fan Company
41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
6-1. Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
Step 6-1 (Detail)
6-2. Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.
6-3. Some blade mounting screws are installed in the motor to
secure shipping blocks. Remove the blade mountings screws and
rubber bumpers from the motor. Save the screws and discard the
bumpers.
Grommet
6-4. For each blade, insert one blade mounting screw through the
blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.
Steps 6-1 – 6-2
Blade Assembly
Screws
9
Use with grommet
Use without grommet
Blade Mounting
Screw
Step 6-4
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Installing the Light Fixture
WARNING: Use only the light fixture supplied with this fan model.
7-1. To attach the upper switch housing, partially install two #6-32 x
3/8” housing assembly screws into the switch housing mounting
plate.
7-2. Feed the upper plug connector through the center opening of the
housing.
7-3. Align the keyhole slots in the housing with the housing assembly
screws.
7-4. Turn the housing counterclockwise until the housing assembly
screws are firmly situated in the narrow end of the keyhole slots.
Install the remaining #6-32 x 3/8” screw into the housing. Tighten
all three screws firmly.
Steps 7-1 – 7-4
Housing
Assembly
Screw
CAUTION: Make sure the upper switch housing is securely
attached to the switch housing mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
switch housing and light fixture falling.
Upper
Switch
Housing
10
7-5. read the wires from the lower switch housing assembly through
the center hole.
7-6. To attach the lower switch housing, connect the upper plug
connector from the motor to the lower plug connector in the
lower switch housing assembly.
Plug
Connector
Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
7-7. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower switch
housings. Attach the lower switch housing to the upper switch
housing with three housing assembly screws. Note: You will need
to rotate the blade irons out of the way for each screw.
Steps 7-6 – 7-7
Lower Switch
Housing
Housing
Assembly
Screw
Hunter Fan Company
41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch Housing Cover
7-8. Align the bracket with the reversing switch hole on the switch
housing cover. Snap the bracket into place.
7-9. Attach the switch housing cover by partially installing the
assembly screw.
7-10. Connect the wires from the switch housing to the wires from
the light kit as follows: connect the black wire to black wire and
connect the white wire to white wire. Place the wires into the
light kit assembly.
7-11. To connect the wires, hold the bare metal leads together and
place a wire nut over them, then twist clockwise until tight.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
7-12. Place the key slot on the light kit over the screw attached to the
bracket. Twist the light kit assembly into place and tighten the
screw securely.
Bracket
Steps 7-8 – 7-10
7-13. Install and tighten the remaining screw securely.
7-14. Install two A-19 bulbs (60 watts maximum each).
Assembly
Screw
11
7-15. Install the glass bowl, cap, and finial. Be sure to thread the pull
chains through as shown. Securely tighten the finial.
Assembly
Screw
Key Slot
Glass Bowl
Light Kit
Assembly
Cap
Finial
Wire Nut
Step 7-15
Steps 7-12 – 7-13
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan.
8-2. e fan pull chain controls power to the fan. e pull chain has
four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• e chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
8-3. e light pull chain controls power to the light. e pull chain has
two settings: On and Off.
In warm weather, use
downward air flow pattern
8-4. Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In cold weather, having the fan draw air upward (clockwise
blade rotation) will distribute the warmer air trapped at the
ceiling around the room without causing a draft.
12
8-5. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
8-6. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
Hunter Fan Company
41873-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Tighten the blade bracket screws until snug.
2. Tighten the blade screws until snug.
3. Check to see if the blade is cracked. If so, replace all the blades.
4. Change to an approved speed control.
5. Be sure that the glass is secure.
6. Check and tighten the screws in the switch housing mounting
plate and in the upper and lower switch housing.
13
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade and/or blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
41873-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|