Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
INSTALLATION OVERVIEW
Determining How to Mount the Transducer
Your Humminbird fishfinder includes a standard
transducer. This transducer can be mounted on the
transom of the boat or bonded to the inside of a fiberglass
hull boat.
The transom installation, which is the most widely used,
places the transducer on the outside of the boat hull. This
technique produces the least signal loss, and provides a
way to adjust the transducer after installation. The
mounting hardware included is designed to protect both
the boat and the transducer should the boat strike debris in
the water or when trailering.
As an alternative to transom mounting, it is possible on
many fiberglass-hulled boats to glue the transducer on
the inside of the boat hull. Since fiberglass has similar
sonar characteristics as water, the sonar signal can
pass through the boat hull with minimal loss. The hull
of the boat must be single layer construction (not
double-hulled) Also, any air trapped in the lamination
of the fiberglass would prevent the sonar signal from
passing through.
Inside the hull installations require no holes be drilled
into the boat and through experimentation, high-speed
operation comparable to transom mounting can be achieved. Two-part slow cure
epoxy (not included) is required to glue the transducer in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
ALTERNATE MOUNTING METHODS
ALTERNATE TRANSDUCERS AND MOUNTING METHODS
Your Humminbird fishfinder comes with everything necessary for installation and
operation on most boats. However, there are several situations which may
require a different type of transducer. Inboard boats, wood or metal hulls, and sail
boats create unique transducer mounting needs Alternate transducers and
mounting methods are detailed below.
Portable Mounting
The standard transducer can be adapted for portable
installations with a portable mounting kit available from
Humminbird. This accessory adapts your transducer to a
suction cup mount for temporary installation on the boat hull
or other surface.
Trolling Motor Mounting
The standard transducer can also be adapted to mount on
most trolling motors using a different accessory kit. This
accessory includes a bracket and hose clamp that allows
mounting the transducer to the body of most trolling motors.
Thru-Hull Mounting
Thru-hull transducers install through a hole drilled in the hull
of the boat. Larger boats or boats with inboard motors create
turbulence that make transom mounting ineffective. Also,
hulls that are very thick or are double layered, or made from
materials such as wood or metal, (which do not conduct
sonar signals) make inside the hull mounting inadvisable.
Thru-hull mounting may require the use of a fairing block to level the transducer
with the waterline. Also, since special tools and knowledge may be required to
perform this type of installation, it is best to refer to a qualified marine technician.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
TRANSDUCER EXCHANGE
TRANSDUCER EXCHANGE
Other transducers are available as replacements for the standard transducer.
You may exchange your new and unassembled transducer for another type by
returning it to the address listed in Customer Support. Some transducers may
have additional cost. Refer to the Accessory catalog or call Customer Support for
information.
BEGINNING INSTALLATION
Now that you have determined the transducer mounting method you can begin
installation of your new Humminbird fishfinder. The installation guide included on
the next few pages provides detailed step by step instructions for installation of
the control head and transducer. For transom mount transducer installations you
will need the mounting template included with your manual.
In addition to the parts included you need the following for installation and
operation:
·
·
·
·
·
·
·
·
·
A powered hand drill and various drill bits
Philips and flat-head screwdrivers
A ruler or measuring tape
Pen or pencil
12 volt power source (your boat’s battery)
A 1-amp fuse
A fuse holder (if you are wiring directly to the boat’s battery)
Silicone sealant (for sealing drilled holes)
2-part, slow-cure epoxy (for inside the hull transducer installations)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Do not begin this transducer installation until you read the Installation
Preparation in the Operation Guide. This chapter contains information
critical to the correct installation of your transducer.
Due to the wide variety of boat hulls, only general instructions are
presented in the installation guide. Each boat hull represents a unique set
of requirements that should be evaluated prior to installation.
TRANSOM INSTALLATION
Step One - Determine Where to Mount the Transducer
Begin the transducer installation by determining where on the
transom to install the transducer. Consider the following to find
the best location:
·
·
It is very important to locate the transducer in an area which is
relatively free of turbulent water, As a boat moves through the
water, turbulence is generated by the weight of the boat, and
the thrust of the propeller(s). This turbulent water is normally
confined to areas immediately aft of ribs, strakes or rows of
rivets on the bottom of the boat, and in the immediate area of
the propeller(s) (Figure 1). On outboard or inboard/outboard
boats it is best to stay at least 15” (40cm) to the side of the
propeller(s).
If possible, viewing the transom of the boat while the boat is
moving will provide the best means of locating turbulence free
water. If maximum high-speed operation is a high priority, this
is the recommended method. If this is not possible, select a
location on the transom where the hull forward of this location
is smooth, flat, and free of protrusions or ribs.
·
·
The transducer when mounted should point straight down.
The design of the transducer will accommodate a wide range
of deadrises and remain ported straight down (Figure 2).
On boats with stepped hulls, it may be possible to mount the transducer on
the step. Never mount the transducer on the transom behind a step, as this
area of the transom will not be in contact with the water at high speed (Figure
3).
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
·
If the propeller(s) is (are) forward of the transom, it may be impossible to find
an area clear from turbulence, and a different mounting technique or
transducer type should be considered.
Step Two - Drill the Mounting Holes
1. Remove the mounting template from the front of the Operations Manual.
2. Hold the template on the transom of the boat in the location where the
transducer will be installed (Figure 4). Align the template vertically, ensuring
the lower edge of the transom meets with the bottom corner
of the template.
3. Using a pencil or punch, mark the two mounting holes
shown on the template onto the transom. Do not mark or
drill any other holes at this time.
4. Using a 5/32” (4mm) bit drill the two holes to a depth of
approximately 1" (3cm). On fiberglass hulls, it is best to
start with a smaller bit and use progressively larger drill bits
to reduce the chance of chipping or flaking the outer
coating.
Step Three - Assemble the Transducer
1. Attach the Pivot to the transducer body as shown in Figure
5, using the #8 – 3/8” (9mm) long allen headed pivot screw,
the headed pin, the two flat washers, and the two toothed
lock washers.
Note: The toothed lock washers must be positioned
between the transducer and the pivot ears. The flat
washers must be positioned to the outside at the pivot
ears.
2. Using the AIlen wrenches provided, loosely tighten the pivot
screw (Figure 6). Do not completely tighten the assembly at
this time, so the pivot angle can be adjusted later.
3. Insert the pivot/transducer assembly into the mounting
bracket as shown in Figure 7. Do not snap the assembly
closed.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Step Four - Mount the Transducer to the Transom
1. Apply silicone sealant to the mounting holes drilled into the transom.
2. Align the transducer assembly with the drilled holes in the transom (Figure 8).
3. Use either a flat head screwdriver, a 5/16" (8mm) hex driver, or a 5/16" (8mm)
socket to mount the assembly. Using the two #10 – 1”
(25mm) long slotted hex head screws, mount the transducer
assembly to the transom as shown. Do not fully tighten the
mounting screws in order to vertically adjust the transducer.
Snap the pivot down into place.
Step Five - Adjust the Running Position of the Transducer
The bracket allows height and tilt adjustment, the pivot screws
allow angular adjustment. Initially, adjust the transducer as
described in the following paragraphs. Further adjustment may
be necessary to refine the instillation after high speed testing.
1. First adjust the pivot angle of the transducer body so its
length is parallel with the length of hull of the boat. Then
pivot the transducer down so the rear is about 1/4 inch
(6mm) lower than the front (Figure 9).
2. Fully tighten the two pivot screws using the Allen wrenches.
It may be necessary to retighten the pivot screws after the
initial use as the plastics may still be seating to the lock
washers.
3. Adjust the height of the assembly so the face of the
transducer is 3/16" (4.5mm) beneath the lower edge of the
transom (Figure 10). Mark the position of the mounting
bracket on the transom with a pencil.
4. Force the pivot to the up position to gain access to the
mounting screws. Assure the transducer location has not
changed, then fully tighten the two mounting screws (Figure
11). Snap the pivot back down.
Confirm the pivot angle has not changed.
Note: A third screw location is provided for the
Download from Www.Somanuals.com. All Manuals Search And Download.
mounting bracket. Drill this hole and install the screw after final testing and
adjustments have been completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Step Six - Route the Cable
There are several ways to route the transducer cable to the to the area where the
control head will be installed. The most common procedure routes the cable
through the transom into the boat.
Inside the boat there is often a channel or conduit used for other
wiring that the cable can be routed along. Do not cut or shorten
the transducer cable and try not to damage the cable insulation.
Route the cable as far as practical from the VHF radio antenna
cables or tachometer cable to reduce the possibility of
interference.
If the cable is too short, extension cables are available to extend
the transducer cable up to a total of 50' (15 m). Call Humminbird
Customer Support for more information.
Follow these steps to route the cable through the transom:
1. Drill a 5/8” (16mm) hole above the water line. Route the
cable through the hole.
2. Fill the hole with silicone sealant.
3. Place the escutcheon plate over the hole and attach with the two #8 x 5/8”
(16mm) screws.
4. Secure the cable by attaching the cable camp to the transom using a #8 x
5/8” (16mm) screw.
Note: The transducer will pivot up to 90 degrees in the bracket. Allow
enough slack in the cable for this movement. It is best to route the cable to
the side of the transducer so the cable will not be damaged by the
transducer during movement.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSIDE THE HULL INSTALLATION
INSIDE THE HULL INSTALLATION
Inside the hull installation requires the mount system and control
head be installed and operational. See Installing the Control Head
for instruction on installing the unit.
Inside the hull mounting generally produces good results in single
thickness fiberglass-hulled boats. Humminbird cannot guarantee
depth performance when transmitting and receiving through the
hull of the boat since some signal loss occurs. The amount of loss
depends on hull construction and thickness, and the installation.
This installation requires slow-cure two-part epoxy. Do not use
silicone or any other soft adhesive to install the transducer, as this
material reduces the sensitivity of the unit. Five minute epoxy has
a tendency to cure before all the air bubbles can be purged.
Step One - Determine the Mounting Location
Begin the transducer installation by determining where inside the
hull to install the transducer. Consider the following to find the
best location:
·
Observe the outside of the boat hull to find the areas that are
mostly free from turbulent water. Avoid ribs, strakes, and other
protrusions as these create turbulence (Figure 14).
·
As a general rule, the faster the boat can travel the further aft
and closer to the centerline of the hull the transducer has to be
located to remain in contact with the water at high speeds.
Step Two - Test the Mounting Location
There is no opportunity for adjustment after the transducer glued
in place. Therefore, it is best to perform a trial installation on inside the hull
transducers first, and run the boat at high speeds to determine the best mounting
area.
1. At the identified mounting location, lay the transducer body face down with
the pointed end towards the bow.
2. Fill the hull with enough water to submerge the transducer body. Use a sand
filled bag or other heavy object to hold the transducer in position.
Download from Www.Somanuals.com. All Manuals Search And Download.
The transducer cannot transmit through air. The water purges any air from
between the transducer and the hull and fills any voids in the coarse
fiberglass surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSIDE THE HULL INSTALLATION
3. Power up the Control Head.
4. Run the boat at various speeds and water depths while observing the screen
on the Control Head. If the unit functions well at low speeds but begins to skip
or miss the bottom at higher speeds, the transducer needs to be moved. If
depth performance is required, test the fishfinder in water at the desired
depth. Test different locations in the hull until the optimum performance is
achieved.
Step Three - Permanently Mount the Transducer
1. Once the mounting location is determined, mark the position of the
transducer.
2. Remove the water from inside the hull and thoroughly dry the
mounting surface. If the surface is excessively rough, it may be
necessary to sand the area to provide a smooth mounting
surface.
Ensure the mounting area is clear and dry.
3. Mix an ample quantity of two-part slow-cure epoxy slowly and
thoroughly. Avoid trapping air bubbles.
4. Coat the face of the transducer and the inside of the hull (Figure
16).
5. Press the transducer into place with a slight twisting motion to
purge any trapped air from underneath, keeping the pointed end
of the transducer body pointed forward (Figure 17).
Note: Proper operation requires the pointed end of the
transducer body to face towards the bow.
6. Weight the transducer so it does not move while the epoxy is curing.
When the epoxy cures, no water is necessary inside the hull. Neither water,
spilled gasoline, or oil will affect the performance of the transducer.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
CONTROL HEAD INSTALLATION
Step One - Determine Where to Mount
Begin the installation by determining where to mount the control head. Consider
the following to determine best location:
·
The cables for power, transducer and temp/speed accessories (if applicable)
should be installed first and must reach the mounting location. Extension
cables are available.
·
There are two ways to route the cables to the unit: through a
hole in the mounting surface underneath the mounting bracket
or from a hole outside the mounting bracket. Routing the cables
down under the mount provides maximum weather protection;
however this is not always feasible if the area under the
fishfinder is inaccessible. In this case, route the cables through
a hole at another location and cover with the supplied hole
cover.
·
·
The mounting surface should be adequately supported to
protect the fishfinder from excessive wave shock and vibration,
and provide visibility while in operation.
The mounting area should allow sufficient room for the unit to
pivot and swivel freely, and for easy removal and installation
(Figures 18-19).
Step Two - Connect the Power Cable to the Boat
A 6’ (2m) long power cable is included to supply power to the
fishfinder. You may shorten or lengthen the cable using 18 gauge
multi-stranded copper wire.
CAUTION: Some boats have 24 or 36 volt electric systems. Be
sure your unit is connected to a 12 VDC power supply.
The Power can be connected to the boat's electrical system at two
places: a fuse panel, usually located near the console, or directly to the battery.
If a fuse terminal is available, use crimp-on type electrical connectors (not
included) that match the terminal on the fuse panel. Attach the black wire to
ground, and the red wire to 12 VDC power (Figure 20). Be sure to use a one amp
Download from Www.Somanuals.com. All Manuals Search And Download.
fuse in the connection. If you must wire the control head directly to a battery, be
sure to install an inline fuse holder
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
and one amp fuse (not included) for the protection of the unit (Figure 21).
Humminbird is not responsible for over voltage or over current failures.
In order to minimize the potential for interference with other
marine electronics a separate power source (such as a
second battery) may be necessary.
Step Three - Drill the Mounting Holes
1. Set the mounting bracket in place on the mounting
surface. Mark the four mounting screw locations with a
pencil or punch.
2. Set the mounting bracket aside, and drill the four
mounting screw holes using a 9/64” (3.6mm) bit.
Step Four - Run the Cables
1. If the cables must pass through a hole underneath the
mounting surface, mark and drill a 1” (25mm) hole
centered between the four mounting holes (Figure 22).
Note: if the cables must pass through the mounting
surface at a different location, drill the 1" (25mm) hole at
that location and pass the cables through from
underneath. Also, you must break out the tabs on the
rear of the mounting base using needle nose pliers
(Figures 24-25).
2. Insert all cables through the 1” (25mm) hole from beneath
the mounting surface.
3. Pass the cables through the grommet (if the cable hole is
underneath the mounting bracket) then press the grommet
in place around the cables and into the 1” (25mm) hole.
4. Pass the cables through the mounting base, out the top of
the mounting bracket.
5. Place the mounting bracket on the mounting surface aligned with the drilled
holes. Insert the four flathead wood screws into the mounting holes and
tighten fully (Figure 23).
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional: If the cables pass outside the mounting bracket, install the hole
cover over the hole and fasten in place using the two #8 x 7/8” (22mm)
wood screws (Figure 24).
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
Step Five - Assembling the Connector Holder
1. Insert the cable connectors into the connector holder.
The cable connectors are labeled, and there are
corresponding labels on the connector holder (Figure
26). The slots for the connectors are keyed to prevent
reverse installation, so do not force the connector into
the holder.
2. Carefully pull the excess cable from beneath the -
mounting surface so the connector holder aligns with the
mounting holes on the front of the mounting bracket
(Figure 27).
3. Snap the support plate to the rear of the connector
holder (Figure 28).
4. Insert the connector holder into place and use the two
#6-32 x ¾” (9mm) screws to fasten it to the mounting
bracket (Figure 28).
5. Install the control head by sliding it onto the mounting
bracket until it is fully seated. To remove the unit simply
depress the latch on the rear of the unit and lift (Figure
29).
Your Humminbird is now ready for operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TEST THE INSTALLATION
TEST THE INSTALLATION
Testing should be performed with the boat in the water, however you can initially
confirm basic operation with the boat trailered.
Press POWER once to turn the unit on. There will be an audible chirp when any
button is pressed to confirm the button press. If the unit does not power-up,
ensure the unit is fully seated on the mount and that power is available.
The first screen provides four options: Start-up, Options, Simulator, and
Diagnostic. A message at the bottom of the screen indicates the transducer
connection. If no transducer is detected (or one is not connected), the message
will indicate this and the unit will go into simulator after the initial screen times
out.
Note: the transducer must be submerged in water for reliable transducer
detection.
If a transducer is detected, the unit will enter “Start Up” or normal operation
unless you choose another option. If you do not press any button before the timer
reaches “0”, the normal operation screen is displayed. If the boat is in water,
sonar data appears.
If the bottom is visible on screen with a digital depth readout, the unit is working
properly. Ensure the boat is in water greater than 2’ but less than the depth
capability of the unit and the transducer is fully submerged. Remember the sonar
signal cannot pass through air.
If the unit is working properly gradually increase the boat speed to test high-
speed performance. If the unit-functions well at low speeds but begins to skip or
miss the bottom at higher speeds, the transducer requires adjustment. Refer to
the appropriate transducer installation section for more detail.
Note: it is often necessary to make several incremental transducer
adjustments before optimum high-speed performance is achieved.
Important: For Transom Mount transducer installations, install the third mounting
screw after the final transducer adjustments.
Humminbird · 3 Humminbird Lane · Eufaula, Alabama 36027
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT YOU SEE ON SCREEN
The first thing you may notice about the Wide 3D Vista unit is the high-resolution, wide screen
LCD display. The LCD display uses super-twist technology for maximum viewability and is
ruggedized for tough shock and vibration endurance. The display is also backlit for nighttime
operation, and uses special components so it can operate at temperatures more extreme than
you are likely to encounter.
The Wide 3D Vista gives you three basic ways to view the bottom terrain: 3D view, 2D view, and
the Combo view. Simply pressing the VIEW button will toggle these options. The default view,
which is selected when you first power the unit, is the 3D view shown in Figure a. The sonar
returns from each of the six elements are combined to create a wire-frame type 3D representation
of target location and bottom terrain.
Current information, or the terrain directly beneath
your boat, is displayed on the lower right, and
advances to the left as new information is received.
The view created is an accurate depiction of the
terrain which you have just covered.
In some situations, the selected point of view may
prevent the display of some information due to the
slope of the terrain. If you are traveling in a direction
which will present this situation for an extended
period of time, an option is available to reverse the
view-point to the opposite side of your boat, which
enables you to see information that would otherwise
be masked by the terrain. The normal or default point
of view is called “right perspective” since the view
point is to the right of the boat. Reversing this view
point is called “right perspective” since the view point is to the right of the boat. Reversing this
view point is called “left perspective” (Figure B). This option is available in the System Options
screen which will be discussed in more detail later in this manual.
The 2D view shown in Figure C, will be familiar to previous sonar users. All the information
collected by the six individual beams is compressed into a 2-dimensional presentation. The most
current information is displayed on the right side of the screen and moves to the left as new
information is received.
The Combo view combines a 3D and 2D representation of the same information. This view is
shown in Figure D and is especially useful in learning to use the 3D presentation.
Download from Www.Somanuals.com. All Manuals Search And Download.
A valuable accessory available for use with all Wide 3D products is Wide Side. Your unit has the
capability of displaying information from a special “side-locking” transducer as shown in Figure E.
See the “Advanced Feature” section for more information.
Using the View button to toggle between the three main views gives you the maximum benefit of
each type of view: The 3D view gives you an excellent representation of bottom terrain and
target location, The 2D view is best for determining bottom hardness and texture and locating
structure or bottom detail. The combo view combines both 3D and 2D views to provide the best of
both views.
USING THE 3D VIEW
At power-up, the Wide 3D Vista locates the bottom and adjusts the depth range to a setting
most appropriate for that depth. The bottom will usually be displayed about 2/3 of the way down
the display. Each of the six sonar beams transmits a signal at a rate of about four times per
second. The returned signals from each transmit are compared and evaluated before the
information is displayed, so each display update contains information gathered from several
transit and receive cycles.
Download from Www.Somanuals.com. All Manuals Search And Download.
The digital depth shown on-screen is the depth of the water directly beneath your boat. As new
information is received, the most recent information is displayed at the lower right, directly
underneath the boat symbol. Previous information advances to the left. Boat speed and water
surface temperature are displayed at the upper right. If you have not connected this accessory,
the screen layout will be slightly different. The distance back number represents the linear
distance of the sonar information being displayed. The faster your boat is moving, the greater the
amount of distance will be seen on the screen.
As the depth of the water changes, the Wide 3D Vista will automatically adjust the depth range
and sensitivity as necessary to view the bottom on-screen. The 3D view of the Wide 3D Vista is
capable of tracking the bottom to a depth of 240 feet. Beyond 240 feet, you must select the 2D
view for bottom tracking to 1000 feet. When operating at depths near 240 feet in the 3D or
Combo views, A message will appear warning you of the depth limitations of the 3D view. Also,
the 2D view has a depth capability much greater than the 3D view. The 200 kHz transducer will
provide reliable target and bottom tracking to a depth of 1000 feet.
If a target is detected between the surface and the
bottom and it meets the fish identification criteria, it is
displayed as a fish symbol. Sonar returns that do not
meet this criteria are displayed as “raw” information.
Depending on the strength of the signal reflected from
the target, and other factors, one of three different size
fish symbols used. These reflected signals are
“normalized” for depth, so that a small fish does not
appear to be a large fish if it is close to the boat.
Since some species of fish tend to be better reflectors
of sonar than others, the strength of return is not
always an accurate indicator of fish size, however,
typically, the larger the fish, the larger the signal return.
Additionally, since the Wide3D Vista uses a six element transducer, the position of the target
relative to the boat is known. To help differentiate targets seen directly under the boat from those
seen in the outer beams, these fish symbols are indicated differently. Targets seen in the two
center beams are located directly under your boat, and are displayed as solid fish symbols.
Targets seen in the outer four beams are located in the outer portion of the sonar coverage area
and are displayed as hollow fish symbols. This is true for all views.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE 2D VIEW
When operating in 2D view, the Wide 3D Vista operates as most normal depth sounders with
several exceptions. The six beam 53 degree transducer allows you to search for fish with a much
wider area of coverage than ordinary depth sounders. The hollow and solid fish symbols give you
directional information, and you can quickly switch back to the 3D view for a better idea of where
the target is located.
The 2D view provides more information about bottom hardness and texture using Structure ID.
Only information collected from the center two beams is used to draw the bottom depiction.
Terrain outside the coverage area of the center two beams will not be seen in the 2D view. Using
a narrower beam provides much more detailed information as to the composition of the bottom.
If the bottom is hard and smooth, the bottom depiction will be narrow and dense. If the bottom is
mud or soft sand, the bottom depiction will be thick and less dense. This indicates that much of
the solar signal is absorbed by the soft bottom. If the bottom is rugged and varying, such as a
rocky bottom, the depiction will be textured and vary in density. Structure such as submerged
trees or brush, or other objects are clearly displayed above the solid bottom in varying densities
of pixelization. This bottom depiction is useful in locating structure, by comparing relative density
as well as depth.
The transmitted sonar signal travels downward, and is reflected back toward the surface by the
bottom or other objects for display on-screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
The signal does not stop there- it is reflected downward again by the surface of the water, and a
weak “second return” is usually visible if the depth range is sufficient to see it. The second return
may be used as an indicator for setting the sensitivity bias.
USING THE COMBO VIEW
The Combo view combines a 3D view with a 2D view on the same screen. This is an ideal view
for 2D users learning to interpret 3D information. Also, you can view a wide area of coverage on
the 3D portion of the screen, but retain the bottom detail of the 2D view.
CONTROL FUNCTIONS
The Wide 3D Vista unit uses only eight buttons to control all functions. The controls are divided
into two groups: POWER, STOP, VIEW, and LIGHT are one group., and the Menu System
controls are the other group. When any button is pressed, an audible “chirp” will verify the control
input.
POWER, as previously discussed, powers the Wide 3D Vista for normal
operation. Also if the unit is powered off, press and hold POWER until you
hear a continuous “chirp” to enable simulator operation as discussed in
“Simulator Operation”. Pressing POWER when the unit is in normal or
simulator operation will power the unit off.
STOP freezes the display to allow closer study. Pressing STOP again will
resume normal operation. Also, if a menu is on-screen, STOP will retain the
menu on-screen until STOP is pressed again. The digital bottom depth will
continue to update, as usual, even if the display is stopped.
VIEW toggles between the three main views; 3D view, 2D VIEW, AND
Combo view when using the standard transducer. If you are using the optional
Wide Side transducer, VIEW toggles between the left, right, both, and down
views.
LIGHT enables a two-level display backlight and backlit keypad. Pressing
once will turn the light on low, pressing a second time will increase the
backlight to the high setting, and pressing a third time will turn the backlight off.
The four remaining buttons work together to control the Menu System - an array of menu
controlled functions.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU brings a menu on-screen for adjustment, or if a menu is already present, the next menu in
sequence will appear. Menus will go off-screen and normal operation will resume after a short
period of time. If you wish to keep the menu on-screen for an extended period of time, press
STOP.
UP arrow selects the next larger or next sequential adjustment within the menu. Holding an
Arrow button down will cause the unit to continue to make the adjustment, until a limit is reached,
and the limit alarm sounds.
DOWN arrow selects the next smaller adjustment within the menu.
ENTER is used to toggle other menu options on and off.
All menus use the same general layout as shown in the sample menu. The heading of the menu
is at the top. The area in the center is controlled by the UP and DOWN arrows, and the area
under the horizontal line is controlled by the ENTER button. Not all menus are affected by all
controls, but the layout is the same regardless. Pressing MENU repeatedly will sequentially
display all available menus.
MENU FUNCTIONS
The following section explains each menu in detail, and how these adjustments can be used to
extract the maximum information from the sonar returns. With several exceptions, once a setting
has been changed, the Wide 3D Vista will remember that setting until it is again changed, even if
power is disconnected.
SENSITIVITY
As the Wide 3D Vista receives returned signals, the sensitivity of the receiver is adjusted
automatically based on a number of factors such as the depth of the water, and the signal clarity.
In murky water, full of debris, the Wide 3D Vista will select a lower sensitivity setting. In clear
water, where there is little debris to defract the sonar signal, the sensitivity is set higher.
The sensitivity menu allows you to “bias” this
automatic setting up or down based on personal
preference.
You can select a bias of +5 to –5, for 11 different
bias settings. A bias setting of “0” has no effect on the
automatic function. A +3 setting selects a sensitivity
setting three steps higher than the unit would normally
select, so even the smallest returns are displayed on-
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
A setting of –2 sets the sensitivity two steps below what the unit would normally select, so only
the largest targets of other returns are displayed.
Another use of the Sensitivity menu is to select the bottom representation. In the 2D view the
Wide 3D Vista normally displays a variable Structure ID bottom, which can allow experienced
users to determine the texture or relative hardness of the bottom. For simplicity, you can select a
black bottom using the ENTER button. This blackens in the display below the bottom for easiest
recognition of the bottom location, even from a great distance.
RANGE
The Wide 3D Vista adjusts the depth range automatically, so the bottom return is displayed at
the bottom 1/3 of the display. This leaves the top 2/3 to display anything between the surface and
the bottom. As your boat moves over deeper or shallower water, the unit adjusts the depth range
of the display to keep the bottom return in the same general area on the screen.
However, you may choose to control this range
adjustment manually. By pressing ENTER, you can
select manual operation, meaning the unit will no
longer adjust the depth range automatically. The
depth range selected is controlled by the UP and
DOWN arrow buttons. 3D depth ranges of 0-15 feet,
30 feet, 60 feet, 120 feet, 180 feet, & 240 feet can be
selected. In the 2D view depth ranges will be
extended and include 360 feet, 480 feet, 600 feet, &
1000 feet. An on-screen icon indicates whether the
unit is in “AUTO” (automatic) or MNL (manual) range
control.
If you alter the depth range, the unit will switch to
manual operation. This feature is valuable if you are
only interested in targets near the surface. The Wide
3D Vista will always display the digital depth of the water in the manual mode. If the bottom is not
visible in the depth range selected, a 3D grid will be shown for reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
ZOOM
Another form of range control is Zoom. Zoom allows
selection of various ranges for full screen viewing.,
while maintaining a view of the full range. By using
the display to view a smaller area, the effective
display resolution is increased, and the unit’s ability to
separate targets close together is enhanced.
The zoom range is determined by the depth range in
use when Zoom is enabled. In shallow water, when
the 15 foot or 30 foot depth range is used, the zoom
range will be 7 ½ feet. If the 60 foot or 120 foot depth
range is in use, the zoom range will be 15 feet. And if
the 180 foot or 240 foot depth range is in use the
zoom range will be 30 feet. For depths greater than 240 feet the display will only update a 2D
view. If the depth range is 480 feet the zoom range will be 30 feet and if the depth range is 600
feet or 1000 feet the zoom range will be 60 feet.
Download from Www.Somanuals.com. All Manuals Search And Download.
To enable Zoom, adjust the horizontal lines to the depth of the zoom range using the UP and
DOWN arrow buttons, then enable Zoom using the ENTER button.
Pressing the VIEW button while in zoom will toggle your display from three zoom views; 3D, 2D,
and a combo view. When you are in zoom in the 2D view, refer to the preview area and adjust the
depth of the zoom range by using the UP and DOWN arrow buttons. The combo view also allows
you to preview a 2D view, but displays a zoomed 3D view. The Zoom menu will not appear when
an adjustment is made unless MENU is pressed. The digital depth readout will continue to track
the bottom even when Zoom is enabled.
Bottom Lock is a function of zoom, except the depth adjustment is controlled automatically to
view the area immediately above the bottom. This is especially useful if you are looking for
structure or minor variations in terrain in areas of relatively flat bottom terrain. To enable Bottom
Lock, press ENTER until the “BL” is highlighted. The zoom range will be controlled by the current
depth range, as in Zoom , and will be indicated on the Zoom menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
BOTTOM ALARM
The Wide 3D Vista contains an audible alarm to warn you of shallow water depths. This alarm is
adjustable from 2' to 99' of depth. To enable the alarm, simply adjust the alarm depth using the
UP and DOWN arrow buttons, and press ENTER. When the depth of the water beneath your boat
is equal to or less than the selected alarm depth, a continuous alarm will sound.
To disable the alarm, either move to deeper water, or select the Bottom Alarm menu, and press
ENTER to turn the alarm off.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Fish Alarm alerts you to the presence of fish, or other targets not attached to the bottom, in
the water beneath your boat. The Fish Alarm has 3 different settings which correspond to the 3
different size fish targets shown on-screen.
To enable Fish Alarm, use the UP and DOWN arrow buttons to adjust the size return you want to
be alerted to: large fish only, large and medium size fish, or all fish. Then press ENTER to enable
the alarm.
Remember that it is impossible for Fish Alarm sonar to determine if a signal return is a fish or
some other type of object or suspended debris. Any object not connected to the bottom is
normally a fish and is portrayed as a fish symbol. The strength of the reflected sonar signal from a
target is a good indicator of the size of the target, and the fish symbol displayed represents the
strength of the signal reflected from it.
ID is the automatic identification of target returns based on the strength of the returned signal and
other factors. Three options are available: ID "On" displays targets as one of three different size
fish symbols.
The fish symbols may be hollow, indicating that the target is detected in the wide beam only, or
solid, indicating that the target is detected in the narrow beam, and is located directly under the
boat.
Download from Www.Somanuals.com. All Manuals Search And Download.
"ID+", the default setting, provides more information about the location of the target by attaching
depth "strings" showing the digital depth of the target. When there are numerous targets on-
screen, not every target depth is shown, to avoid excessive clutter on-screen.
ID "Off" disables the units interpretation of targets, and displays the "raw" sonar information as it
is received. Advanced users may prefer this type of presentation, so they can make there own
interpretation from the information displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
TRIPLOG
TripLog provides a time/distance calculation, based on input from the speed accessory. The timer
is started when the unit is first powered, and distance information is collected to provide elapsed
distance since power up, and the average speed. To enable the TripLog display, press ENTER.
Viewing Triplog while in a 2D view allows current sonar information to be displayed.
The TripLog can be reset at any time by pressing STOP. Press ENTER to return to the normal
screen.
Note: The Speed & Temperature accessory must be connected for TripLog to work.
SYSTEM OPTIONS
The System Options menu allows the adjustment of several additional features. These
adjustments are usually made initially, and rarely thereafter. To make these adjustments, first
enter the System Options full screen menu with the ENTER button. Then press MENU to choose
the category for adjustment, the UP and DOWN arrow buttons to adjust the setting, and the
ENTER button to return to the normal screen when you have finished.
Download from Www.Somanuals.com. All Manuals Search And Download.
Scroll Rate controls the rate of update of the display. There are five rate settings available. The
default setting is rate 4 - you may speed up or slow down the update rate to match your personal
preference. To present the most accurate representation of the terrain beneath your boat, the
scroll rate of the display should be approximately synchronized to the speed of the boat. If your
boat is stationary or moving slowly, select a slower scroll rate, and if you typically operate the
boat at high speeds, use a faster scroll rate.
Contrast adjusts the display screen for easier viewing under given light conditions. There are 9
contrast settings available.
Sonar mode controls three different modes of operation. The default position is "down", where the
Wide 3D Vista uses the six-beam down-looking transducer to produce the three primary views
discussed earlier. Selecting "side" will configure the unit to work with the Wide Side, side-looking
transducer which will be discussed in the "Wide Side Operation" section. The third option is
"diagnostic" which is used to evaluate the performance of your installation, or to help find a
suitable inside the hull mounting point for the transducer. Diagnostic is discussed in detail in the
"Advanced Feature" section.
User Level is used to select Normal or Advanced operation. Advanced mode performs several
functions which will benefit the experienced user. Icons are not shown and numerical data is
smaller to allow more of the display to be used for the picture of the bottom. Several other
changes in operation occur which are designed to increase the speed of adjustments, and
maximize the graphic use of the display. Refer to "Advanced Operation" for more detailed
information.
Perspective selects the point of view for the 3D view. Right perspective is the default setting, and
the viewpoint is from the right side of the boat. Left perspective changes the point of view to the
opposite side of the boat. Perspective can be changed to view terrain normally hidden from a
Download from Www.Somanuals.com. All Manuals Search And Download.
particular viewpoint, or just for personal preference. This setting is remembered even after the
unit is turned off.
Units-Speed allows a selection between displaying speed in MPH or KTS. MPH displays your
boat's speed in statute miles per hour and KTS displays your boat's speed in knots or nautical
miles per hour.
Note: Boat speed and water temperature features require the use of the temp/speed accessory.
ADVANCED OPERATION
The Wide 3D Vista contains the unique ability to be adaptable in operation to match the
experience level of he user. Users inexperienced in the operation of the Vide 3D Vista should use
the factory "Normal" setting. 4s your experience increases, you will benefit from many of the
changes that occur when "Advanced" operating mode is selected. The selection is made in the
System Menu and affects the following:
The base screen layout is modified to maximize the display for terrain and target presentation. To
accomplish this, symbols such as Sensitivity setting, and Fish Alarm indicators, are removed.
When a menu adjustment is made, the menu goes off-screen in approximately half the normal
time. Menus are abbreviated and after an adjustment is made only a small indicator remains at
the top of the screen so that you can make quick adjustments. This lets the experienced user
make adjustments, then quickly return to full-screen viewing.
These changes are designed to make the maximum use of the available screen resolution, and
speed up operations that restrict the view of the bottom.
DIAGNOSTIC
Download from Www.Somanuals.com. All Manuals Search And Download.
"Diagnostic" is selected with the sonar mode option of the System menu. It is a special screen
that displays the raw sonar information being received by each of the six sonar beams. Viewing
the information in this manner is helpful when selecting a mounting location for the transducer, or
when troubleshooting potential problems.
If you are selecting a location inside the hull of your boat to mount the Wide 3D Vista transducer,
the diagnostic view lets you compare the individual beam returns while you position the
transducer.
Your boat should be in the water over a flat, level area of bottom. If there are no obstructions or
inconsistencies in the hull at the mounting location, all six beams should be very similar in
appearance. The top of the screen is the surface of the water, and the signal reflected from the
bottom is displayed at the appropriate depth. A weak or irregular signal will be easy to spot, and
moving the transducer slightly may correct the problem.
The Wide 3D Vista transducer is very sensitive to hull irregularities, and care should be taken to
find a location that gives identical returns from each of the six beams.
WIDE SIDE OPERATION
Wide Side is an accessory transducer that gives your
Wide 3D Vista the capability of collecting sonar
information from either side of your boat. Side-looking
sonar is extremely valuable for bank
fishing, or looking for bait fish in open water.
The Wide Side transducer contains 3 different
elements which transmit signals to the left, right, and
straight down from your boat. The downward beam is
200 kHz with a 24 degree area of coverage. This
beam maintains a continuous digital depth readout
from the bottom directly beneath your boat. The side
beams are 455 kHz with a 16 degree area of
coverage. These side-looking elements can be used independently, or together to locate targets
near the surface of the water on either side of your boat.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Wide Side transducer is available as a trolling motor mount, a transom mount, or a portable
mount.
Wide Side can be connected directly to your Wide 3D Vista unit in p/ace of the standard
transducers, or used in conjunction with a transducer switch so that all of the transducers can be
connected to the Wide 3D Vista. See "Installing the Wide 3D Vista" for additional information.
When the Wide Side transducer is connected directly to your unit, or selected using a transducer
switch, the unit setup must be changed to correspond with the type of transducer being used.
This adjustment is made through the "System Options" menu. Use the MENU button to select the
"System Options" menu and press ENTER. Press MENU until the "sonar mode" option is
highlighted. Press UP or DOWN until "side" is displayed. Press ENTER when the selection is
correct.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Wide 3D Vista is now configured for Wide Side operation.
When you exit the "System Options" menu, the view you will see on-screen is shown above.
Viewing both left and right sides simultaneously gives you an excellent tool when searching for
bait fish or following a creek bed, however greater display resolution can be achieved by viewing
only one side.
Experiment with the Wide Side transducer while operating it in a familiar area and learn how to
make maximum use of the information displayed. Remember, if you are using a trolling motor
mount, the information displayed is controlled by the direction the trolling motor is pointing, not
necessarily the direction the boat is travelling.
Download from Www.Somanuals.com. All Manuals Search And Download.
The information collected is controlled by pressing the VIEW button. Pressing VIEW toggles the
options "both", "right', "left", or "dwn" (down). When the "dwn" mode is selected, the single 24
degree down-looking element of the Wide Side transducer is used to collect this information. This
transducer does not have "wide", "narrow", or "dual" beam options and hollow fish symbols
cannot be displayed.
The "Range" menu (below) in Wide Side must be used to control the range manually, as the
bottom is not always visible on-screen. Ranges of 15, 30, 60, and 120 feet are available.
"Zoom" has no function in Wide Side mode and the menu will not be present.
ID menu functions are slightly different in "wide side" and "down" modes. In the "wide side" mode
ID+ is not an option, and all fish are displayed as medium, sized fish symbols. In the "down"
mode ID+ is available, and fish are displayed in three sizes.
Most other menu functions work the same in Wide Side mode as with the standard dual beam
transducer. "Bottom Alarm", "Fish Alarm", and "Sensitivity" have the same effect.
"Triplog" is available, if the speed and temperature accessory is connected.
To return to the normal "down" operation using the standard 3D transducer, you must reconnect
the 3D transducer (by replacing the Wide Side connectors) or use the switch to select the 3D
transducer. Next, configure the unit by selecting the "down" mode under the "System Options"
menu.
Note: The "sonar mode" must always be configured to match the type of transducer being used.
Download from Www.Somanuals.com. All Manuals Search And Download.
|