Humminbird Fish Finder TS1 3 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
by rotating up out of the metal spring bracket without harming the transducer, or your boat.  
The transducer can be re-engaged by simply rotating the transducer down and snapping it  
back in place. (See Figure A)  
B. Inside Hull Mount- The high speed transducer can be mounted inside the hull (without pivot  
assembly) using the proper two-part epoxy, such as Humminbird’s epoxy kit. Even though  
there is some loss of signal in shooting through the hull, your LCR will perform well with this  
type of installation. You cannot shoot through the hull of an aluminum boat.  
C. Trolling motor Mount- This type of transducer is not supplied with your LCR. It is designed to  
mount on the foot of a trolling motor. You may exchange your un-used high speed  
transducer for a trolling motor transducer. Call the Humminbird Customer Service  
Department.  
D. Bronz Thru-Hull Mount- This transducer is not supplied with your LCR but for an additional  
cost you may exchange your un-used high speed transducer for a bronz thru-hull. The bronz  
thru-hull transducer has a threaded stem which installs through a hole drilled in the boat hull,  
leaving the housing exposed under the boat. This type of installation must be used for many  
boats with in-board engines, because there is no suitable location on the transom away from  
the noise and turbulence created by the prop. A bronz thru-hull transducer should be installed  
by qualified personnel only.  
The LCR will operate well at high speeds with a properly mounted transducer. Remember, a  
transducer will not work transmitting through air or through air bubbles.  
1. TRANSOM MOUNTING PROCEDURE  
Step 1.  
MOUNTING LOCATION- It is important that the transducer be mounted on the transom where  
water flow is in constant contact with the transducer. You may wish to observe the rear of the  
boat while it is moving through the water to determine the best mounting location.  
Step 2.  
BRACKET INSTALLATION (Aluminum Boats)- To install the metal bracket on an aluminum boat  
locate the template on the transom between rows of rivets, or ribs that are on the bottom of the  
boat. Align the template so that the bottom corner of the template nearest the center of the  
transom is on the bottom edge of the transom.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Once the location is determined mark and drill three 7/64” dia.. holes noted on the template.  
Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in  
the center of the  
Bracket slots. On some aluminum boats it may be necessary to use a wood back-up plate. It is  
important to use a silicone sealant between the screwhead and bracket in order to prevent  
leaking. (See Figure C)  
Step 2.  
BRACKET INSTALLATION (Fiberglass Boats)- If your boat has a stepped transom located  
below and under the main transom, the compact transducer design allows mounting in this area.  
This mounting location is recommended for good reading at very high speeds. (See Figure D)  
To install the metal bracket on a fiberglass boat, locate the template on the transom in the same  
manner as for an aluminum boat. (See Figure C)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the  
transducer slightly off parallel with the water level. (See Figure E)  
Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using  
the three #10 self threading screws supplied. Be sure to align the holes so that they are centered  
vertically in the three slots found in the bracket. It is important to use a silicone sealant between  
the screwhead and bracket in order to prevent leaking.  
Step 3.  
TRANSDUCER PIVOT ASSEMBLY- Assemble the pivot to the transducer main body using the  
two ¼”x5/8” allen head screws, two 3/8” tooth washers and two, ¼” square nuts. Make sure the  
tooth washers are sandwiched between the transducer main body and the pivot. The square nuts  
are trapped inside the pivot and will not rotate as the allen head screws are tightened.  
HOWEVER, DO NOT TIGHTEN AT THIS POINT. (See Figure F)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 4  
TRANSDUCER ASSEMBLY- Insert the transducer assembly into the metal bracket from the  
bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket.  
Slide the O-ring on to the headed pin and insert it through the two parts. Assemble by screwing  
the ¼”x3/8” allen head screw into the end of the pin and tighten. (See Figure G)  
Step 5  
ANGLE ALLIGHMENT- Set the transducer angle so that it is parallel with the bottom of the boat  
hull. Once proper alignment is achieved, tighten the two allen head screws using the 5/32” allen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
wrench provided. The screws are visible through the access holes on each side of the metal  
bracket. Check to make sure the transducer main body is rigidly fastened to the pivot. (See  
Figure H)  
Step 6  
CHECK POSITION OF TRANSDUCER- At this point, check to see that the bottom of the  
transducer is a minimum of ¼” below the bottom of the transom. (However, as noted in STEP 2,  
the top of the transducer cannot fall below the bottom of the transom). If it is not, remove the  
transducer assembly from the metal bracket by removing the pin installed during STEP 3. Loosen  
the metal bracket mounting screws, re-position the bracket utilizing it’s slotted holes, tighten and  
re-assemble. It may be necessary to replace the silicone sealant after this adjustment is made.  
NOTE: It may be necessary to make several high speed runs to adjust transducer either  
UP/DOWN or to re-adjust the angle to achieve optimum results.  
Step 7  
CABLE CLAMPS- Install cable clamps as necessary by drilling a 1/8” dia. hole for the # 8 screw  
supplied.  
2. INSIDE HULL MOUNTING PROCEDURE  
Warning: In order to achieve proper results with this type installation, it is important that the  
transducer be mounted by someone familiar with the use of two part epoxy adhesives. For this  
reason, Techsonic Industries, Inc. will not be responsible for any damage due to the mounting of  
your transducer in this manner.  
NOTE: An Epoxy Kit (Part N. EPK) is available from Humminbird. This Epoxy Kit has been  
formulated for Inside Hull Transducer Installation.  
1. Select as flat an area as possible near the aft end and center of boat where the hull is thin  
and not double. If the bottom has a runner down the center of boat, select an area to one side  
of the runner, but as close to the runner as possible.  
2. Clean the inside of the boat with lacquer thinner in the area transducer is to be mounted.  
Outside of boat in this area should also be cleaned. (Not with lacquer thinner).  
3. Put approximately one inch of water in the bottom of the boat.  
4. Put transducer in the water. The bottom of the transducer should be in a flat area and should  
be in good contact with the bottom of the boat.  
5. Operate the LCR with the boat operating at high speed. The transducer may have to be  
moved in order to find an area where satisfactory operation is observed.  
6. When an area is found that produces satisfactory operation, mark the location of the  
transducer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Remove the water and transducer and clean the marked area and the bottom of the  
transducer thoroughly.  
8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without  
causing it to bubble and pour it in the area the transducer is to be mounted. The puddle  
should be larger than the bottom of the transducer.  
9. Coat the bottom of the transducer with epoxy, then put it in the center of the puddle and push  
down on the transducer while moving it around in a circular motion. This forces out any air  
bubbles that may be trapped between the bottom of the transducer and the hull of the boat.  
10. Let epoxy cure then the transducer is ready to operate. No water is now required in the  
bottom of the boat and gas and oil that is spilled inside of the boat will not degrade  
performance as it will if the transducer is placed only in water.  
CAUTION: Do not use the silicone seal or any soft adhesive to bond the transducer to the  
hull. This will reduce the sensitivity of the unit.  
CAUTIONS  
1. Occasionally the “eye“ of your transducer may become dirty from storage or from contact with  
oils present in boats or marina environments. (Oil will cause the “eye” to lose the intimate  
contact with the water which is necessary for efficient operation.) The “eye” may be cleaned  
with liquid detergent.  
2. Improper installation of the transducer can alter the efficiency and accuracy of the entire  
system.  
3. If your boat of transducer is out of the water for a period of time, it may take a short period of  
time for the transducer to become thoroughly “wetted” when returned to the water. Also, re-  
entry may cause turbulence, which will create air bubbles in the “eye” of the transducer. The  
bubbles will disappear in a short time or can be removed by rubbing the transducer “eye” with  
your fingers while the transducer is in the water.  
4. If your instrument should fail to function, be sure to check all the electrical connections before  
removing the transducer or calling a serviceman.  
5. Inspect your transducer cable and make sure that it has not been cut or damaged to the point  
where it will affect the performance of the transducer. A slight nick or cut, exposing the outer  
cable, can be repaired by wrapping with electrical tape. A transducer can be damaged if the  
inner cable and outer cable are allowed to make contact. Such a problem can sometimes be  
corrected by properly splicing the coaxial cable. This should only be attempted by a qualified  
service technician.  
6. If your LCR is not working properly and you suspect the problem might be in your transducer,  
we would recommend you borrow a unit from a friend and try it on your boat. If the symptoms  
are the same, you can almost be certain that the problem is in the transducer.  
INSTALLING THE LCR  
The LCR should be mounted on a flat, solid surface for maximum stability. The low profile swivel  
mount has four holes drilled in the base. It is recommended that all four holes be used.  
Position the swivel base and drill four ¼” diameter holes. Note: The LCR hole pattern Is the same  
as for all Humminbird flasher units. Use hardware provided to mount this base to the boat.  
Next place the gimbal bracket on the swivel base and attach with four small machine screws,  
provided.  
Place the LCR in the gimbal mount and make certain the rubber washers provided are placed  
between the unit and the gimbal bracket Important: Note which side of the gimbal faces forward.  
(Slots on gimbal bracket go towards rear). Also, rubber washer must be located between the unit  
and the gimbal bracket.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilted to any  
desired position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OTHER MOUNTING OPTIONS  
1. The LCR gimbal bracket can also be mounted on the SM-4, quick disconnect swivel mount.  
2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount,  
however, this method is not recommended since the unit cannot be rotated.  
INSTALLING THE CABLES  
Your LCR comes equipped with Humminbird’s new Angle-Lock power and transducer  
connectors. The power connector is identified with the letter P on the back of the plug.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is  
identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”.  
Note: An adapter (AD-4) is available to allow use of an old waterproof (BNC) transducer with the  
LCR, but be sure that the transducer is a 16degree. A 32-degree transducer cannot be used.  
A 11/8” hole must be drilled to pull through the transducer connector. After drilling the hole, pull  
the transducer connector up through the hole. If you are installing two units, both transducer  
connectors can be pulled through this 1 1/8” inch hole. Next, push the power cable wires down  
through the hole. A hole cover has been provided which will dress and hold the wires. Install the  
hole cover after determining the necessary wire length from the hole.  
The power cable has a red lead to the positive (+) post and the black lead to the negative (-) post.  
Install a 1 amp fuse between the red cable and positive post of your 12-volt battery.  
If a fuse panel is available, we recommend wiring the power cable into the fuse panel. Note: The  
LCR must be fused separately from any other accessory.  
Your Angle-Lock connectors can only be plugged in one way. Position the connector so the letter  
P or T can be read and the 90 degree bend is pointed downward. Push the connector in as far as  
it will go. Turn the positive locking ring as far as it will go clockwise until you feel it lock. Locking  
ring as far as it will go clockwise until you feel it lock. Your connector is now locked into place.  
Note: For easy access to the connectors, simply loosen the mounting knobs and tilt your LCR  
forward. The connectors are now in full view and easy to plug or unplug.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING: This device should not be used as a navigation aid to prevent collision, grounding,  
boat damage or personal injury. When the boat is moving, submerged objects will not be seen  
until they are already under the boat or bottom depths may change too quickly to allow time for  
the boat operator to react. Always operate the boat at very slow speeds if you suspect shallow  
water or submerged objects.  
"MADE BETTER TO WORK BETTER"  
This manual covers the installation and operation of your Humminbird Depth Sounder.  
Techsonic Industries, Inc. One Humminbird Lane Lake Eufaula, AL 36027  
"WE'RE CHANGING THE WAY YOU FISH"  
INTRODUCTION  
Congratulations! You have just purchased the finest depth sounder on the market. Your  
Humminbird has been engineered and built to meet the rugged standards of today's  
discriminating fishermen. In addition to telling you how deep the water is, your Humminbird will  
also reveal underwater structure, as well as fish.  
IMPORTANT  
Save the box your Humminbird came in. In the event you should need to return it to our plant, you  
should use this as your shipping carton.  
WARNING  
Please read this instruction manual thoroughly before attempting to operate your Humminbird.  
Failure to follow proper operation or installation procedures could nullify your warranty.  
NOTE: Please complete and mail warranty card immediately after purchase.  
Good luck and good fishing from your friends at Techsonic.  
HUMMINBIRD FEATURES  
("Or why your 'Bird outperforms all other brands.')  
Gold Plated Contacts - Gold is one of the best conductors of electricity known, and unlike other  
metals, it will not corrode. This is why our waterproof flasher units are equipped with gold plated  
contact points on both the transducer and power cable connectors.  
Completely Waterproof-Tough inner and outer ABS material cases house all flasher units. Sealed  
with watertight "0" rings so that rain, humidity, spray (including salt water) or condensation will not  
affect your Humminbird.  
Epoxy Based Printed Circuit Boards - We use a tough epoxy filled fiberglass printed circuit board,  
built to military specifications. Unlike paper based boards, the epoxy based board will not crack or  
break, and will stand up to long term use in rough water.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Positive Noise Reject System - Easily adjustable control knob to eliminate interference and false  
signals with the Humminbird positive noise reject system.  
High Speed Readings - Clear bottom readings at any speed up to 75 miles per hour can be  
achieved providing the transducer has been properly installed.  
Super-Bright Thin Line Lamp-Even in bright sunlight, the flasher super-bright thin line lamp gives  
detailed readings.  
Night Light- Humminbird's patented night light makes for easy night readings. There is no  
additional power drain because the digits adjacent to the flash are lighted by the flash itself.  
Other Features  
Crystal Control Oscillators for better performance and reliability.  
Solid State Electronic Circuitry. Microcomputer Controlled. Heavy Duty Motor for better  
performance and longer life. Lifetime-Guaranteed Service Policy with three day turnaround and a  
one year full warranty.  
Transducers- Humminbird builds all our own transducers. The revolutionary new design means  
better performance, finer quality and instant pickup. These transducers never require sanding.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THEORY OF OPERATION  
Your depth sounder works on the sonar  
principle. The control head generates an  
electronic signal which is coupled to the  
transducer where it is changed to an  
ultrasonic signal. This signal travels through  
the water until it hits an object or the lake  
bottom. The signal is then reflected back to  
the transducer, where it is changed back to  
an electronic signal.  
The control head measures the amount of  
time it takes the signal to travel from the  
transducer to the reflecting object and back  
again. This time is then converted into feet  
(since the signal travels at a constant speed -  
approximately 4800 feet per second), and the  
number of feet to the object is indicated on  
the calibrated dial with the spinning lamp.  
The lamp revolves around the dial once for  
each 120 foot reading on the 120 foot units  
and once for each 60 foot reading on the 60  
foot units. Therefore, the motor in the 120  
foot unit rotates at 1200 rpm and in the 60  
foot unit 2400 rpm. The motor in the Super  
Thirty II unit also travels at the speed of 2400  
rpm. This is accomplished by the use of an  
integrated circuit signal processor which  
permits a 30 foot readout to be displayed on  
a unit running at the speed of a 60 foot  
model.  
YOUR TRANSDUCER  
The transducer is the transmit/receive "antenna" of your depth sounder. The transducer converts  
an electrical signal from your instrument into accoustical energy which is then transmitted through  
the "eye" of the transducer into the water. The return signal (echo) excites the "eye" with an  
accoustical shock wave and causes the transducer to send an electrical signal back to your  
instrument. The "eye" of the transducer is the flat portion that is focused downward into the water.  
For maximum efficiency the transducer's "eye" must not be obstructed and it must be in intimate  
contact with the water ("wetted'').  
It is suggested you keep the face of the transducer clean. This can be done with soap and water.  
NOTE: In order for your Humminbird to perform at Its maximum potential, care should be taken to  
Install the transducer properly. This Is the most critical part of the Humminbird Installation. Please  
read the following sections thoroughly and follow the installation instructions carefully.  
TRANSDUCER MOUNTING OPTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A. Transom Mount - The Humminbird high speed transducer allows the transducer element to be  
mounted below the bottom of the boat hull keeping the transducer out of turbulent water and  
insuring good high speed operation. The transducer will absorb the blow of any obstruction by  
rotating up out of the metal spring bracket without harming the transducer, or your boat. The  
transducer can be re-engaged by simply rotating the transducer down and snapping it back in  
place.  
B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot  
assembly) using the proper two-part epoxy, such as Humminbird's epoxy kit. It is important to  
carefully follow the mounting procedure in this manual to insure that a proper mounting location is  
selected. Improper mounting will result in loss of depth sounder signal. Do not shoot through the  
hull of an aluminum boat.  
C. Trolling Motor Mount - This type of transducer is not supplied with your unit. It is designed to  
mount on the foot of a trolling motor. You may exchange your un-used high speed transducer for  
a trolling motor transducer. Call the Humminbird Customer Service Department.  
D. Bronze Thru-Hull Mount - This transducer is not supplied with your unit but for an additional  
cost you may exchange your un-used high speed tranducer for a bronze thru-hull. The bronze  
thruhull transducer has a threaded stem which installs through a hole drilled in the boat hull,  
leaving the housing exposed under the boat. This type of installation must be used for many  
boats with inboard engines, because there is no suitable location on the transom away from noise  
and turbulence created by the prop. A bronze thru-hull transducer should be  
installed by qualified personnel only. E. Transducer Exchange - You many exchange your un-  
used transducer for another type, however, some exchanges may require an additional charge.  
Please call the Humminbird Customer Service Department TOLL FREE number listed in the front  
of the manual. Your unit will operate well at high speeds with a properly mounted transducer.  
Remember, a transducer will not work transmitting through air or air bubbles.  
CAUTIONS  
1. Occassionally the "eye" of your transducer may become dirty from storage or from  
contact with oils present in boats or marina environments. (Oil will cause the "eye" to lose  
the intimate contact with the water which is necessary for efficient operation.) The "eye"  
may be cleaned with liquid detergent.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Improper installation of the transducer can alter the efficiency and accuracy of the entire  
system.  
3. If your boat or transducer is out of the water for a period of time, it may take a short  
period of time for the transducer to become thoroughly "wetted" when returned to the  
water. Also, re-entry may cause the turbulence which will create air bubbles on the "eye"  
of the transducer. The bubbles will disappear in a short time or can be removed by  
rubbing the transducer "eye" with your fingers while the transducer is in the water.  
4. If your instrument should fail to function, be sure to check all the electrical connections  
before removing the transducer or calling a serviceman.  
5. Inspect your transducer cable and make sure that it has not been cut or damaged to the  
point where it will affect the performance of the transducer. A slight nick or cut, exposing  
the outer cable, can be repaired by wrapping with electrical tape. A transducer can be  
damaged if the inner cable and outer cable are allowed to make contact. Such a problem  
can sometimes be corrected by properly splicing the coaxial cable. This should only be  
attemped by a qualified service technician.  
6. If your unit is not working properly and you suspect the problem might be in your  
transducer, we would recommend you borrow a unit from a friend and try it on your boat.  
If the symptoms are the same, you can almost be assured that the problem is in the  
transducer.  
TRANSOM MOUNTING PROCEDURE  
Step 1  
MOUNTING LOCATION - It is important that the transducer be mounted on the transom where  
water flow is in constant contact with the transducer. You may wish to observe the rear of the  
boat while it is moving through the water to determine the best mounting location.  
Step 2 (Aluminum Boats)  
BRACKET INSTALLATION To install the metal bracket on an aluminum boat locate the template  
on the transom between rows of rivets, or ribs that are on the bottom of the boat. NOTE:  
Template is on the last page of the manual. Align the template so that the bottom corner of the  
template nearest the center of the transom is on the bottom edge of the transom. (See figure 3.)  
Once the location is determined mark and drill three 7/64" dia holes noted on the template. Attach  
the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the  
center of the bracket slots. On some aluminum boats it may be necessary to use a wood back-up  
plate. It is important to use a silicone sealant between the screwhead and bracket in order to  
prevent leaking. (See Figure 4).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 2 (Fiberglass Boats) BRACKET INSTALLATION - If your boat has a stepped transom  
located below and under the main transom, the compact transducer design allows mounting in  
this area. This mounting location is recommended for good reading at very high speeds. (See  
Figure 5).  
To install the metal bracket on a fiberglass boat, locate the template on the transom in the same  
manner as for an aluminum boat. (See figure 4). NOTE: On boats with more than 15° deadrise  
angle it may be necessary to mount the transducer slightly off parallel with the water level. (See  
Figure 6).  
Mark and drill the three 9/6," dia holes as shown on the template. Attach the metal bracket using  
the three #10 self threading screws supplied. Be sure to align the holes so that they are centered  
vertically in the three slots found in the bracket. It is important to use a silicone sealant between  
the screwhead and bracket in order to prevent leaking.  
Step 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSDUCER PIVOT ASSEMBLY Assemble the pivot to the transducer main body using the  
two 1/4x%" alien head screws, two %," tooth washers and two'/," square nuts. Make sure the  
tooth washers are sandwiched between the transducer main body and the pivot. (See Figure 7).  
The square nuts are trapped inside the pivot and will not rotate as the alien head screws an;  
tightened. HOWEVER, DO NOT TIGHTEN AT THIS POINT (See Figure 7).  
CAUTION: DO NOT APPLY LOCTITE® OR SIMILAR LOCKING COMPOUNDS BECAUSE  
THEY WILL ATTACK THE PLASTIC.  
Step 4  
TRANSDUCER ASSEMBLY -Insert the transducer assembly into the metal bracket from the  
bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket.  
(See Figure 8). Slide the O-ring on to the headed pin and insert it through the two parts.  
Assemble by screwing the '/,"x%" alien head screw into the head of the pin and tighten.  
Step 5  
ANGLE ALIGNMENT - Set the transducer angle so that it is parallel with the bottom of the boat  
hull. (See figure 9). Once proper alignment is achieved, tighten the two alien head screws using  
the %2" alien wrench provided. The screws are visible through the access holes on each side of  
the metal bracket. Check to be sure the transducer main body is rigidly fastened to the pivot.  
Step 6  
CHECK POSITION OF TRANSDUCER At this point, check to see that the bottom of the  
transducer is a minimum of %," below the bottom of the transom.  
(However, as noted in STEP 2, the top of the transducer cannot fall below the bottom of the  
transom). If it is not, remove the transducer assembly from the metal bracket by removing the pin  
installed during STEP 3. (See Figure 8). Loosen the metal bracket mounting screws, reposition  
the bracket utilizing it's slotted holes, tighten and reassemble. It may be necessary to replace the  
silicone sealant after this adjustment is made.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: It may be necessary to make several high speed runs to adjust transducer either  
UP/DOWN or to readjust the angle to achieve optimum results.  
Step 7 CABLE CLAMPS - Install cable clamps as necessary by drilling a %' dia. hole for the #8  
screw supplied. Be sure to route the cable to the side of the bracket. The cable can be cut if it is  
installed in the center of the bracket. (See Figure 10). FIGURE 10  
3. INSIDE HULL MOUNTING PROCEDURE  
Warning: In order to achieve proper results with this type installation, it is important that the  
transducer be mounted by someone familiar with the use of two part epoxy adhesives. For this  
reason, Techsonic Industries, Inc. will not be responsible for any damage due to the mounting of  
your transducer in this manner.  
IMPORTANT: Be sure to follow steps 3 through 6 to insure that a proper mounting location is  
found. Do not epoxy the transducer until this is done. It may not be possible to find a good  
mounting location on some boat hulls due to their construction.  
1. Select as flat an area as possible near the aft end and center of boat where the hull is thin and  
not double. If the bottom has a runner down the center of boat, select an area to one side of the  
runner, but as close to the runner as possible.  
2. Clean the inside of the boat with lacquer thinner in the area transducer is to be mounted.  
Outside of boat in this area should also be cleaned. (Not with lacquer thinner.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Put approximately one inch of water in the bottom of the boat.  
4. Put transducer in the water. The bottom of the transducer should be in a flat area and should  
be in good contact with the bottom of the boat. 5. Operate the unit with the boat operating at high  
speed. The transducer may have to be moved in order to find an area where satisfactory  
operation is observed.  
6. When an area is found that produces satisfactory operation, mark the location of the  
transducer.  
7. Remove the water and transducer and clean the marked area and the bottom of the transducer  
thoroughly.  
8. Using the Humminbird Epoxy Kit mix an ample amount of epoxy without causing it to bubble  
and pour it in the area the transducer is to be mounted. The puddle should be larger than the  
bottom of the transducer.  
9. Coat the bottom of the transducer with epoxy, then put in the center of the puddle and push  
down on transducer while moving it around in a circular motion. This forces out any air bubbles  
that may be trapped between the bottom of the transducer and the hull of the boat.  
10. Let epoxy cure then the transducer is ready to operate. No water is now required in the  
bottom of the boat and gas and oil that is spilled inside of the boat will not degrade performance  
as it will if the transducer is placed only in water. Caution: Do not use silicone seal or any soft  
adhesive to bond the transducer to the hull. This will reduce the sensitivity of the unit.  
3. TROLLING MOTOR MOUNTING PROCEDURE  
A "Trolling Motor Transducer," is designed to be mounted on the foot of the trolling motor with the  
aid of an adjustable clamp, included standard (see below). Your trolling motor transducer will give  
an excellent reading with no interference from the electric motor. Some boat manufacturers are  
now glassing in a second transducer beneath the front deck for thru the hull reading of the  
forward mounted depth sounder. This installation also serves a dual purpose in that a fisherman  
can run his big motor at idle speed and use his front depth sounder to scan for submerged  
stumps or obstacles. Such a practice can often prevent damage to props and lower units of the  
big outboard.  
MATCHING THE PROPER TRANSDUCER  
A 2" diameter transducer is used on all Humminbird flasher units, except the Super Thirty II which  
uses a 1" diameter transducer.  
The 2" transducer emits a 16 degree cone angle which, we feel, is most efficient for medium to  
deep range flasher units. It concentrates the signal on a given target for a better medium to deep  
return, thus a better display on the flasher dial.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The 1" transducer used on the Super Thirty II emits a 32 degress cone angle. This wider beam is  
used in shallow water since it provides a wider area of coverage.  
NOTE: While the 1" transducer is recommended for the Super 3011, some may prefer the  
performance of the 2" transducer. Either will work and it may be a matter of personal preference  
as to which one is used.  
TRANSDUCER SWITCH ASSEMBLIES FOR MODELS TS1-3 AND TS2-3  
The Transducer Switch Model TS1-3 comes complete with one switch and one extension cable.  
This switch allows you to use one Humminbird depth sounder with two transducers and is ideal  
when using one transducer mounted on the transom and the other transducer mounted on your  
trolling motor.  
The transducer switch model TS2-3 comes complete with one switch and two extension cables.  
This switch allows you to use two Humminbird Depth Sounders with a single transducer, mounted  
anywhere feasible for your application.  
NOTE: With switch in this position depth sounder operates from Transducer #2.  
We recommend the use of our new Swivel Mount SM-4 (not shown) in conjunction with our TS1-  
3.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting Instructions: Drill a %" hole in the desired location and mount switch with extra nut and  
washer provided. See illustrations below for correct cable connections.  
NOTE: With switch in this position depth sounder #2 operates from the transducer.  
INSTALLING THE CABLES  
Your unit comes equipped with Humminbird's AngleLockT'" power and transducer connectors.  
The power connector is identified with the letter P on the back of the plug. It plugs into the outlet  
on the back of the unit marked "Power." The transducer connector is identified with the Letter T  
and plugs into the outlet on the back of the unit marked "Transducer." Note: An adapter (AD-4) is  
available to allow use of an old waterproof (BNC) transducer with the new Angle-Lock T"'  
connector.  
A 1 1/8" hole must be drilled to pull the transducer connector through the dash. After drilling the  
hole, pull the transducer connector up through the hole. If you are installing two units, both  
transducer connectors can be pulled through this 1'/B inch hole. A hole cover has been provided  
which will dress and hold the wires. Install the hole cover after determining the necessary wire  
length from the hole.  
The power cable has a red lead and a black lead. Connect this cable to a 12-volt DC Power  
Source (battery). Attach the red lead to the positive (+) post and the black lead to the negative (-)  
post. Install a 2 amp fuse between the red cable and positive post of your 12-volt battery.  
If a fuse panel is available, we recommend wiring the power cable into the fuse panel. `Note: The  
unit must be fused separately from any other accessory.  
Your Angle-LockTm connectors can only be plugged in one way. Position the connector so the  
letter P or T can be read and the 90 degree bend is pointed downward. Push the connector in as  
far as it will go. Turn the positive locking ring as far as it will go clockwise until you feel it lock.  
Your connector is now locked into place.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING SCREW INSTRUCTIONS  
Important: Always use special flat washers provided with mounting screws when mounting unit to  
prevent breaking plastic knob due to overtightening. Washers must be installed as shown above  
between gimbal bracket and knob.  
IN-DASH UNIT  
The first completely waterproof, flush-mount unit on the market. Fits snugly in the dash, is  
attractive and virtually theft-proof. Gives same great detail as the original Super Sixty. Operates  
from a single, independently mounted on/off switch, with built-in noise suppression.  
IN-DASH INSTALLATION INSTRUCTIONS  
1. After selecting a location for your unit and control knob, check under the dash for clearance. 2.  
Drill a 3.5 inch diameter hole where you have chosen to put your unit. 3. Now slide your unit into  
the hole from the front side of the dash. (Note orientation of unit face before completing the  
following steps.)  
4. Next, slide the mounting bracket over the bottom of the unit (see next page).  
5. Install the flat washer, lock washer and nut onto the two bolts and tighten.  
NOTE: Do not over tighten the hex nuts as this may cause damage to the unit. Do not apply  
Locktite or similar locking compounds to the unit or bracket as this may cause damage to the unit.  
6. The OFF-SENS control of your unit requires a 3/e" hole in close proximity of the unit (due to  
cable length).  
7. After drilling, install the off-sensitivity label by peeling off the back label and placing around the  
3/e" hole.  
8. On the blushing (threaded portion) of the control there are 2 hex nuts. Adjust one to  
accommodate the dash of your boat and the other to tighten. Now slide the black control knob  
onto the control shaft.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. The final step is to connect the control cable and transducer to the unit. You may choose to  
mount your In-Dash Sixty in a location other than in the dash. This can be accomplished with the  
use of the Humminbird Bow Mount DBID. This bracket for the In-Dash allows the unit to be  
mounted on any flush surface such as on the console, bow or casting deck.  
GENERAL OPERATIONAL INSTRUCTIONS  
The OFF-SENS knob turns the unit on and off. This SENS (sensitivity) control also adjusts the  
circuit so the signal returned from the bottom is strong enough to produce a good display on the  
dial. If it is set to produce too strong a signal, echoes will appear on the dial at multiples of the  
water depth. This, however, should not be objectionable as long as the operator recognizes the  
echoes for what they are. The sensitivity control incorporated in this depth sounder is not a linear  
control. In other words, the change in sensitivity is very little for the % turn of the knob. The unit is  
designed in this manner in order to allow accurate readings in water which is as little as one foot  
deep. Because of this, however, it will be necessary to turn the knob to an almost fully clockwise  
position in order to obtain proper operation in deeper water. This does not mean that the  
sensitivity of the unit is lessened. Boat motors and other electrical devices can send out electrical  
noise that may show as erratic flashes on the dial. The NOISE REJECT knob adjusts the control  
head so these noise flashes cannot be seen. This knob is turned clockwise to reject noise pulses.  
See page 20 for noise reject adjustment instructions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: The Humminbird In-Dash Sixty has a noise reject system built in.  
NOTE: A large number of modern fishing boats are now equipped with two depth sounders, one  
of which is mounted on the console with the transducer positioned near the back. The second unit  
is positioned in front with the transducer mounted off the foot of the trolling motor. Occasionally,  
when both units are being operated with full gain, there will be a revolving signal flashing around  
one or both dials. This is a result of an overlap of signals due to the expanding cone angle of the  
transducer (See Figure 11). This same condition will occur when you pull alongside of another  
boat with its depth sounder in operation. This signal will not affect the performance of the unit and  
can usually be eliminated by reducing the amount of sensitivity. To avoid the possibility of the  
intermingling signals, the transducers should be positioned as far apart as possible upon initial  
installation.  
Refer to illustrations on page 18 as you read the following paragraphs.  
OFF-SENS Adjustment  
Move the boat out into 5 to 10 feet of water. Shut off the boat motor and any electronic device  
that may cause electrical interference. Turn the NOISE REJECT knob fully counterclockwise.  
Turn the OFF-SENS knob just past the click. The dial should flash at 0 feet (see indication A).  
Turn the knob clockwise as needed to get a good lake bottom flash at the water depth (see  
indication B). Turn the knob farther clockwise and echoes will appear (see indication C). As a rule  
of thumb, adjust the sensitivity clockwise until you see the second echo (indication C). This will  
normally give you good bottom and fish returns.  
In order to allow readings in very shallow water (one to five feet) the SENS control has a special  
taper which requires that it be turned almost fully clockwise to read depths over 30 to 40 feet.  
This in no way means that your unit is not sensitive as it will read depths up to 200 feet. This  
control does, however, allow more control of your signal at shallow depths.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOISE REJECT ADJUSTMENT  
NOTE: When the NOISE REJECT knob is turned clockwise, the amount of the reflected signal  
may be slightly reduced. Therefore, turn this knob clockwise only as far as needed to reduce  
interference. If there is no interference, this knob can be left in the full counterclockwise position.  
NOTE: The Humminbird In-Dash Sixty is the only model with a NOISE REJECT system built in.  
Start the boat motor and look for a flashing, moving pattern that covers the circumference of the  
dial (see indication D). If these flashes cannot be sufficiently reduced by turning the NOISE  
REJECT knob clockwise, reposition the transducer and cable away from the motor to obtain a  
minimum number of interference flashes. Then turn the NOISE REJECT knob as far clockwise as  
is necessary to reduce the interference. If the interference still cannot be sufficiently reduced,  
contact the motor manufacturer for information on reducing ignition interference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO READ THE DIAL  
Objects Under Water A lake bottom is seldom level or uniform,  
and objects in the water or on the bottom may also vary in  
depth. The dial readings will indicate these varying conditions  
accordingly. To distinguish between the dial indications of rocks  
and fish, anchor the boat and watch for signals that change. A  
changing signal will usually indicate a moving fish.  
Pages 23 through 25 show you examples of underwater  
conditions and dial readings. Study these drawings for help in  
interpreting what you read on the dial.  
NOTE: For additional information and illustrations showing the  
interpretation of the depth sounder readings, refer to the  
"Humminbird Trouble Shooting and Consumer Information  
Guide."  
This booklet is available at no charge from Humminbird  
Customer Service Department. i-800-633-1468. Alabama  
residents should call 1-800-821-8315.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION OF THE SUPER THIRTY 11 IN VERY SHALLOW WATER  
The Humminbird Super Thirty II will operate in the same manner as our Super 60 except the unit  
with its wide graduations is ideally suited for shallow water applications. This unit measures to 30  
feet on the first revolution and will operate satisfactorily in water depths of 100 feet or more. Since  
the unit is designed for shallow water, we recommend that it be mounted forward and in  
conjunction with a trolling motor mount. In certain areas of the country, such as Florida, where  
many bodies of water rarely exceed 30 feet in depth, the Super Thirty II can be successfully used  
as a console mount. When operating the Super Thirty II in water deeper than 30 feet, simply  
move the selector switch to the 60 foot setting. The range on the first revolution will then be up to  
60 feet as shown on the inner dial.  
The slightest change in depth can readily be detected with the Super Thirty II. We recommend  
you start with a minimum amount of gain, and increase it as needed.  
If the depth continues past 60 feet, the bottom signal will continue past zero and you will continue  
to get an accurate depth reading by adding the additional depth to 60 feet.  
OPERATION OF THE SUPER SIXTY AND IN-DASH SIXTY MODELS IN WATER DEEPER  
THAN 80 FEET  
When operating the Humminbird Super Sixty and the Humminbird In-Dash Sixty depth  
sounders in water deeper than 60 feet the flash will continue past zero, and at this point the inside  
dial should be read. The inside dial reads up to 120 feet. For depths greater than 120 feet (two  
complete turns around the dial) add 120 feet to outer dial reading where the flash stops.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BIRDTRAP  
The Birdtrap allows you to make a portable unit of any permanent mount Humminbird Depth  
Sounder except the In-Dash.  
Follow the installation instructions received with your portable Birdtrap, then refer to the  
operational section of this manual for proper use.  
Batteries should be the type with the curled up wire tops. They should be placed side by side,  
upright in the battery compartment in the front of the Birdtrap. See "BATTERY CONNECTION  
DIAGRAM" on page 30 for proper wiring instructions.  
60 FOOT-DIAL INDICATIONS FOR VARIOUS DEPTHS  
(Add 60 Ft. For Each Complete Turn Of Dial)  
SMALL AND LARGE FISH IN DEEP WATER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Birdtrap is used in the same manner as a permanent mount unit. The transducer may be  
mounted using the suction cup as shown in Figure 12 or, if you have a fiberglass boat with a  
single hull, the transducer may be paced in a small amount of water in the hull of the boat.  
NOTE: The water must be in direct contact with the hull of the boat.  
There cannot be any air between the bottom of the transducer and the hull of the boat.  
The metal finger (with the yellow tip) is designed to hold the suction cup onto the boat at idle or  
slow speeds. DO NOT use this finger as a handle to remove the suction cup. When running at  
medium to high speeds you should first take the transducer out of the water because the suction  
cup cannot hold at these speeds.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PORTABLE TRANSDUCER ASSEMBLY  
Follow illustration instructions.  
CAUTION: You should tie down the transducer cable, so that if the suction cup comes loose it will  
not allow the transducer to be damaged by the propeller or possibly pull the unit out of the boat.  
Humminbird will not be responsible for any damage due to the suction cup becoming loose.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTRUCTION DIAGRAM FOR CONNECTING 6 VOLT BATTERIES TO PORTABLE  
BIRDTRAP  
Use two six volt lantern batteries with spring terminals. Connect as shown above.  
BATTERIES  
All Models operate from the 12 volt system on your boat or a 12 volt dry cell source. The dry cell  
source may be two 6 volt cells connected in series.  
Replace or charge the batteries when you notice that the dial motor has slowed down. This  
indicates that the battery voltage has fallen below 10 volts and this low voltage will cause the dial  
lamp to flash at less than the actual depth.  
NOTE; A weak battery will sometimes cause the lamp not to flash even though the motor still  
runs.  
NOTE: If the lamp on your depth sounder does not flash or flashes intermittently, check your  
battery connections. Very often a battery will operate your trolling motor or crank your outboard  
motor, but still not have enough voltage to operate the depth sounder. This is due to the fact that  
trolling motors and starter motors are current sensitive whereas the depth sounder is voltage  
sensitive.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICE FISHING WITH THE BIRDTRAP  
The Birdtrap provides an excellent aid to ice fishermen. The unit will read accurately when placed  
on top of the ice provided that a little moisture is formed beneath the transducer.  
NOTE: This procedure does not work if an air gap develops between ice and water.  
A small amount of water poured on the surface of the ice will provide a suitable puddle in which to  
place the transducer. Schools of fish can often be located before drilling holes, thus saving time  
and energy on the part of the fisherman.  
In extremely cold temperatures, battery life can be extended by placing the Birdtrap inside a  
styrofoam insulated chest. A small portable hand warmer placed beneath the unit will also help  
conserve the batteries.  
HUMMINBIRD TROUBLE SHOOTING GUIDE  
Your Humminbird depth sounder is engineered and manufactured with care and precision and is  
tested time and time again before leaving our plant. Each unit is backed by a written warranty and  
is guaranteed to perform to your satisfaction.  
We have found that in many cases, problems arising with the operation of a Humminbird can be  
traced back to a minor error in installation or an oversight on the part of the operator.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you should ever experience any operational problem with your Humminbird, please refer to the  
following Trouble Shooting guide. If, after checking the various areas described, you are still  
experiencing problems, we would suggest you return your unit to our plant for repair.  
NOTE: Please keep this operations manual in a convenient spot, where it is easily accessible.  
Also save the original carton your Humminbird came in, in case you should ever need to return it  
for service.  
Multiple Flashes at Regular Intervals  
If the OFF-SENS knob is turned too far clockwise, the signal will bounce back and forth several  
times between the bottom and the boat. This will cause flashes at multiples of the depth reading.  
CURE: Turn the OFF-SENS knob counterclockwise until you get a good bottom reading.  
Unusual Readings  
The signal that is reflected back to the transducer from the bottom, or fish, must be strong enough  
to produce a good clear flash on the dial. Weak flashes or no flashes at all usually indicate that  
the OFF-SENS knob is turned too far counterclockwise, that you are above deep, decayed  
vegetation, or that you are in water over 200 feet deep. In the last two cases, the signal would  
probably be absorbed by the bottom or never reach it.  
If the NOISE REJECT knob is turned up too high, some of the signal may also be lost.  
Motor Does Not Turn  
Check power cable contacts.  
No Light  
Reverse wires at the battery.  
Motor Turns, No Light  
Check voltage input to depth sounder, 10 volts minimum.  
HUMMINBIRD TROUBLE SHOOTING GUIDE (continued)  
Motor Turns, "0" Lights, No Bottom Reading Turn sensitivity knob full clockwise, noise rejection  
knob full counterclockwise. Plug and unplug transducer connector"0" reading should increase in  
width when transducer is plugged in.  
Rub water into the face of the transducer to provide for proper wetting.  
Check for cuts in cable.  
If transducer is mounted inside boat, refer to page 10.  
Cannot Obtain High Speed Reading If transducer is mounted inside boat, refer to page 7. If  
transducer is mounted on outside of boat, check to see that transducer is on driver's side and is  
flush with the bottom and transom of boat. Tilt back of transducer slightly down to insure  
transducer stays in contact with the water during high speed operation.  
Be sure transducer is clear of ribs, rivets or other protrusions that may cause air bubbles to pass  
under the transducer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cannot Obtain Deep Reading If mounted inside boat, be sure transducer is properly installed with  
fiberglass or epoxy resin. If transducer is inside the hull and is not bonded to the hull, the area  
must be filled with clean water, free of oil.  
Be sure transducer is pointing as straight down as possible with boat in the water.  
Proper Operation of Depth Sounder Noise rejection control should be at a minimum setting which  
will eliminate any electrical noises which are shown as erratic and random flashes on the depth  
sounder.  
Sensitivity control should be at a maximum setting just creating a double echo on your depth  
sounder. Think of the sensitivity control as the volume control on your radio - the deeper the  
water, the more control (clockwise) required.  
Humminbird Service Policy  
The best products in the industry are backed by the best service policy in the industry. Even  
though you'll probably never need to take advantage of our incredible service guarantee, it's good  
to know that we back our units this well. We do it because you deserve the best.  
One-Year Full Warranty First-year repairs on your unit will be made absolutely FREE (physical  
damage not included).  
Limited Maximum Service Charge After the warranty period, a limited maximum service charge is  
the most you will pay for each repair (physical damage and missing parts not included).  
Factory-Trained Technicians All repair work is performed by factory-trained technicians to meet  
exacting factory specifications.  
Strictest Factory Testing Factory-serviced units go through the same rigorous quality-control  
inspections and full burnin as new units.  
At Humminbird, our goal is to serve our customers with only the highest level of quality, in our  
products and in our service. This service policy is valid in the US and Canada, applies only to  
Humminbird units returned to our factory in Eufaula, Alabama, and is subject to change without  
notice.  
If for any reason your HUMMINBIRD unit fails to operate within one year of date of purchase,  
TECHSONIC INDUSTRIES, INC. will repair it at no charge except for the following items:  
1. You will be charged for any lost parts. 2. You will be charged for repair of any physical  
damage. 3. Transportation charges will be the responsibility of the purchaser.  
THIS IS A FULL WARRANTY AS DEFINED BY THE FEDERAL WARRANTY ACT, EFFECTIVE  
JULY 4, 1975.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Inc Paint Sprayer 222973 User Manual
Grindmaster Beverage Dispenser PIC 6 User Manual
Haier Washer HWM 120 AS User Manual
Hearth and Home Technologies Stove 21M ACC User Manual
Honeywell Air Conditioner PC8900A User Manual
HP Hewlett Packard Laptop 2000 2a12HE User Manual
Huffy Fitness Equipment MCM108DB User Manual
Husqvarna Brush Cutter 3325 User Manual
Husqvarna Lawn Mower YTH210XP User Manual
Impex Home Gym MCH 1510 User Manual