Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
INSTALLATION OVERVIEW
Determining How to Mount the Transducer
Your Humminbird fishfinder includes a standard
transducer. This transducer can be mounted on the
transom of the boat or bonded to the inside of a fiberglass
hull boat.
The transom installation, which is the most widely used,
places the transducer on the outside of the boat hull. This
technique produces the least signal loss, and provides a
way to adjust the transducer after installation. The
mounting hardware included is designed to protect both
the boat and the transducer should the boat strike debris in
the water or when trailering.
As an alternative to transom mounting, it is possible on
many fiberglass-hulled boats to glue the transducer on
the inside of the boat hull. Since fiberglass has similar
sonar characteristics as water, the sonar signal can
pass through the boat hull with minimal loss. The hull
of the boat must be single layer construction (not
double-hulled) Also, any air trapped in the lamination
of the fiberglass would prevent the sonar signal from
passing through.
Inside the hull installations require no holes be drilled
into the boat and through experimentation, high-speed
operation comparable to transom mounting can be achieved. Two-part slow cure
epoxy (not included) is required to glue the transducer in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
ALTERNATE MOUNTING METHODS
ALTERNATE TRANSDUCERS AND MOUNTING METHODS
Your Humminbird fishfinder comes with everything necessary for installation and
operation on most boats. However, there are several situations which may
require a different type of transducer. Inboard boats, wood or metal hulls, and sail
boats create unique transducer mounting needs Alternate transducers and
mounting methods are detailed below.
Portable Mounting
The standard transducer can be adapted for portable
installations with a portable mounting kit available from
Humminbird. This accessory adapts your transducer to a
suction cup mount for temporary installation on the boat hull
or other surface.
Trolling Motor Mounting
The standard transducer can also be adapted to mount on
most trolling motors using a different accessory kit. This
accessory includes a bracket and hose clamp that allows
mounting the transducer to the body of most trolling motors.
Thru-Hull Mounting
Thru-hull transducers install through a hole drilled in the hull
of the boat. Larger boats or boats with inboard motors create
turbulence that make transom mounting ineffective. Also,
hulls that are very thick or are double layered, or made from
materials such as wood or metal, (which do not conduct
sonar signals) make inside the hull mounting inadvisable.
Thru-hull mounting may require the use of a fairing block to level the transducer
with the waterline. Also, since special tools and knowledge may be required to
perform this type of installation, it is best to refer to a qualified marine technician.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PREPARATION
TRANSDUCER EXCHANGE
TRANSDUCER EXCHANGE
Other transducers are available as replacements for the standard transducer.
You may exchange your new and unassembled transducer for another type by
returning it to the address listed in Customer Support. Some transducers may
have additional cost. Refer to the Accessory catalog or call Customer Support for
information.
BEGINNING INSTALLATION
Now that you have determined the transducer mounting method you can begin
installation of your new Humminbird fishfinder. The installation guide included on
the next few pages provides detailed step by step instructions for installation of
the control head and transducer. For transom mount transducer installations you
will need the mounting template included with your manual.
In addition to the parts included you need the following for installation and
operation:
·
·
·
·
·
·
·
·
·
A powered hand drill and various drill bits
Philips and flat-head screwdrivers
A ruler or measuring tape
Pen or pencil
12 volt power source (your boat’s battery)
A 1-amp fuse
A fuse holder (if you are wiring directly to the boat’s battery)
Silicone sealant (for sealing drilled holes)
2-part, slow-cure epoxy (for inside the hull transducer installations)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Do not begin this transducer installation until you read the Installation
Preparation in the Operation Guide. This chapter contains information
critical to the correct installation of your transducer.
Due to the wide variety of boat hulls, only general instructions are
presented in the installation guide. Each boat hull represents a unique set
of requirements that should be evaluated prior to installation.
TRANSOM INSTALLATION
Step One - Determine Where to Mount the Transducer
Begin the transducer installation by determining where on the
transom to install the transducer. Consider the following to find
the best location:
·
·
It is very important to locate the transducer in an area which is
relatively free of turbulent water, As a boat moves through the
water, turbulence is generated by the weight of the boat, and
the thrust of the propeller(s). This turbulent water is normally
confined to areas immediately aft of ribs, strakes or rows of
rivets on the bottom of the boat, and in the immediate area of
the propeller(s) (Figure 1). On outboard or inboard/outboard
boats it is best to stay at least 15” (40cm) to the side of the
propeller(s).
If possible, viewing the transom of the boat while the boat is
moving will provide the best means of locating turbulence free
water. If maximum high-speed operation is a high priority, this
is the recommended method. If this is not possible, select a
location on the transom where the hull forward of this location
is smooth, flat, and free of protrusions or ribs.
·
·
The transducer when mounted should point straight down.
The design of the transducer will accommodate a wide range
of deadrises and remain ported straight down (Figure 2).
On boats with stepped hulls, it may be possible to mount the transducer on
the step. Never mount the transducer on the transom behind a step, as this
area of the transom will not be in contact with the water at high speed (Figure
3).
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
·
If the propeller(s) is (are) forward of the transom, it may be impossible to find
an area clear from turbulence, and a different mounting technique or
transducer type should be considered.
Step Two - Drill the Mounting Holes
1. Remove the mounting template from the front of the Operations Manual.
2. Hold the template on the transom of the boat in the location where the
transducer will be installed (Figure 4). Align the template vertically, ensuring
the lower edge of the transom meets with the bottom corner
of the template.
3. Using a pencil or punch, mark the two mounting holes
shown on the template onto the transom. Do not mark or
drill any other holes at this time.
4. Using a 5/32” (4mm) bit drill the two holes to a depth of
approximately 1" (3cm). On fiberglass hulls, it is best to
start with a smaller bit and use progressively larger drill bits
to reduce the chance of chipping or flaking the outer
coating.
Step Three - Assemble the Transducer
1. Attach the Pivot to the transducer body as shown in Figure
5, using the #8 – 3/8” (9mm) long allen headed pivot screw,
the headed pin, the two flat washers, and the two toothed
lock washers.
Note: The toothed lock washers must be positioned
between the transducer and the pivot ears. The flat
washers must be positioned to the outside at the pivot
ears.
2. Using the AIlen wrenches provided, loosely tighten the pivot
screw (Figure 6). Do not completely tighten the assembly at
this time, so the pivot angle can be adjusted later.
3. Insert the pivot/transducer assembly into the mounting
bracket as shown in Figure 7. Do not snap the assembly
closed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Step Four - Mount the Transducer to the Transom
1. Apply silicone sealant to the mounting holes drilled into the transom.
2. Align the transducer assembly with the drilled holes in the transom (Figure 8).
3. Use either a flat head screwdriver, a 5/16" (8mm) hex driver, or a 5/16" (8mm)
socket to mount the assembly. Using the two #10 – 1”
(25mm) long slotted hex head screws, mount the transducer
assembly to the transom as shown. Do not fully tighten the
mounting screws in order to vertically adjust the transducer.
Snap the pivot down into place.
Step Five - Adjust the Running Position of the Transducer
The bracket allows height and tilt adjustment, the pivot screws
allow angular adjustment. Initially, adjust the transducer as
described in the following paragraphs. Further adjustment may
be necessary to refine the instillation after high speed testing.
1. First adjust the pivot angle of the transducer body so its
length is parallel with the length of hull of the boat. Then
pivot the transducer down so the rear is about 1/4 inch
(6mm) lower than the front (Figure 9).
2. Fully tighten the two pivot screws using the Allen wrenches.
It may be necessary to retighten the pivot screws after the
initial use as the plastics may still be seating to the lock
washers.
3. Adjust the height of the assembly so the face of the
transducer is 3/16" (4.5mm) beneath the lower edge of the
transom (Figure 10). Mark the position of the mounting
bracket on the transom with a pencil.
4. Force the pivot to the up position to gain access to the
mounting screws. Assure the transducer location has not
changed, then fully tighten the two mounting screws (Figure
11). Snap the pivot back down.
Confirm the pivot angle has not changed.
Note: A third screw location is provided for the
Download from Www.Somanuals.com. All Manuals Search And Download.
mounting bracket. Drill this hole and install the screw after final testing and
adjustments have been completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TRANSOM INSTALLATION
Step Six - Route the Cable
There are several ways to route the transducer cable to the to the area where the
control head will be installed. The most common procedure routes the cable
through the transom into the boat.
Inside the boat there is often a channel or conduit used for other
wiring that the cable can be routed along. Do not cut or shorten
the transducer cable and try not to damage the cable insulation.
Route the cable as far as practical from the VHF radio antenna
cables or tachometer cable to reduce the possibility of
interference.
If the cable is too short, extension cables are available to extend
the transducer cable up to a total of 50' (15 m). Call Humminbird
Customer Support for more information.
Follow these steps to route the cable through the transom:
1. Drill a 5/8” (16mm) hole above the water line. Route the
cable through the hole.
2. Fill the hole with silicone sealant.
3. Place the escutcheon plate over the hole and attach with the two #8 x 5/8”
(16mm) screws.
4. Secure the cable by attaching the cable camp to the transom using a #8 x
5/8” (16mm) screw.
Note: The transducer will pivot up to 90 degrees in the bracket. Allow
enough slack in the cable for this movement. It is best to route the cable to
the side of the transducer so the cable will not be damaged by the
transducer during movement.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSIDE THE HULL INSTALLATION
INSIDE THE HULL INSTALLATION
Inside the hull installation requires the mount system and control
head be installed and operational. See Installing the Control Head
for instruction on installing the unit.
Inside the hull mounting generally produces good results in single
thickness fiberglass-hulled boats. Humminbird cannot guarantee
depth performance when transmitting and receiving through the
hull of the boat since some signal loss occurs. The amount of loss
depends on hull construction and thickness, and the installation.
This installation requires slow-cure two-part epoxy. Do not use
silicone or any other soft adhesive to install the transducer, as this
material reduces the sensitivity of the unit. Five minute epoxy has
a tendency to cure before all the air bubbles can be purged.
Step One - Determine the Mounting Location
Begin the transducer installation by determining where inside the
hull to install the transducer. Consider the following to find the
best location:
·
Observe the outside of the boat hull to find the areas that are
mostly free from turbulent water. Avoid ribs, strakes, and other
protrusions as these create turbulence (Figure 14).
·
As a general rule, the faster the boat can travel the further aft
and closer to the centerline of the hull the transducer has to be
located to remain in contact with the water at high speeds.
Step Two - Test the Mounting Location
There is no opportunity for adjustment after the transducer glued
in place. Therefore, it is best to perform a trial installation on inside the hull
transducers first, and run the boat at high speeds to determine the best mounting
area.
1. At the identified mounting location, lay the transducer body face down with
the pointed end towards the bow.
2. Fill the hull with enough water to submerge the transducer body. Use a sand
filled bag or other heavy object to hold the transducer in position.
Download from Www.Somanuals.com. All Manuals Search And Download.
The transducer cannot transmit through air. The water purges any air from
between the transducer and the hull and fills any voids in the coarse
fiberglass surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSIDE THE HULL INSTALLATION
3. Power up the Control Head.
4. Run the boat at various speeds and water depths while observing the screen
on the Control Head. If the unit functions well at low speeds but begins to skip
or miss the bottom at higher speeds, the transducer needs to be moved. If
depth performance is required, test the fishfinder in water at the desired
depth. Test different locations in the hull until the optimum performance is
achieved.
Step Three - Permanently Mount the Transducer
1. Once the mounting location is determined, mark the position of the
transducer.
2. Remove the water from inside the hull and thoroughly dry the
mounting surface. If the surface is excessively rough, it may be
necessary to sand the area to provide a smooth mounting
surface.
Ensure the mounting area is clear and dry.
3. Mix an ample quantity of two-part slow-cure epoxy slowly and
thoroughly. Avoid trapping air bubbles.
4. Coat the face of the transducer and the inside of the hull (Figure
16).
5. Press the transducer into place with a slight twisting motion to
purge any trapped air from underneath, keeping the pointed end
of the transducer body pointed forward (Figure 17).
Note: Proper operation requires the pointed end of the
transducer body to face towards the bow.
6. Weight the transducer so it does not move while the epoxy is curing.
When the epoxy cures, no water is necessary inside the hull. Neither water,
spilled gasoline, or oil will affect the performance of the transducer.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
CONTROL HEAD INSTALLATION
Step One - Determine Where to Mount
Begin the installation by determining where to mount the control head. Consider
the following to determine best location:
·
The cables for power, transducer and temp/speed accessories (if applicable)
should be installed first and must reach the mounting location. Extension
cables are available.
·
There are two ways to route the cables to the unit: through a
hole in the mounting surface underneath the mounting bracket
or from a hole outside the mounting bracket. Routing the cables
down under the mount provides maximum weather protection;
however this is not always feasible if the area under the
fishfinder is inaccessible. In this case, route the cables through
a hole at another location and cover with the supplied hole
cover.
·
·
The mounting surface should be adequately supported to
protect the fishfinder from excessive wave shock and vibration,
and provide visibility while in operation.
The mounting area should allow sufficient room for the unit to
pivot and swivel freely, and for easy removal and installation
(Figures 18-19).
Step Two - Connect the Power Cable to the Boat
A 6’ (2m) long power cable is included to supply power to the
fishfinder. You may shorten or lengthen the cable using 18 gauge
multi-stranded copper wire.
CAUTION: Some boats have 24 or 36 volt electric systems. Be
sure your unit is connected to a 12 VDC power supply.
The Power can be connected to the boat's electrical system at two
places: a fuse panel, usually located near the console, or directly to the battery.
If a fuse terminal is available, use crimp-on type electrical connectors (not
included) that match the terminal on the fuse panel. Attach the black wire to
ground, and the red wire to 12 VDC power (Figure 20). Be sure to use a one amp
Download from Www.Somanuals.com. All Manuals Search And Download.
fuse in the connection. If you must wire the control head directly to a battery, be
sure to install an inline fuse holder
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
and one amp fuse (not included) for the protection of the unit (Figure 21).
Humminbird is not responsible for over voltage or over current failures.
In order to minimize the potential for interference with other
marine electronics a separate power source (such as a
second battery) may be necessary.
Step Three - Drill the Mounting Holes
1. Set the mounting bracket in place on the mounting
surface. Mark the four mounting screw locations with a
pencil or punch.
2. Set the mounting bracket aside, and drill the four
mounting screw holes using a 9/64” (3.6mm) bit.
Step Four - Run the Cables
1. If the cables must pass through a hole underneath the
mounting surface, mark and drill a 1” (25mm) hole
centered between the four mounting holes (Figure 22).
Note: if the cables must pass through the mounting
surface at a different location, drill the 1" (25mm) hole at
that location and pass the cables through from
underneath. Also, you must break out the tabs on the
rear of the mounting base using needle nose pliers
(Figures 24-25).
2. Insert all cables through the 1” (25mm) hole from beneath
the mounting surface.
3. Pass the cables through the grommet (if the cable hole is
underneath the mounting bracket) then press the grommet
in place around the cables and into the 1” (25mm) hole.
4. Pass the cables through the mounting base, out the top of
the mounting bracket.
5. Place the mounting bracket on the mounting surface aligned with the drilled
holes. Insert the four flathead wood screws into the mounting holes and
tighten fully (Figure 23).
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional: If the cables pass outside the mounting bracket, install the hole
cover over the hole and fasten in place using the two #8 x 7/8” (22mm)
wood screws (Figure 24).
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CONTROL HEAD INSTALLATION
Step Five - Assembling the Connector Holder
1. Insert the cable connectors into the connector holder.
The cable connectors are labeled, and there are
corresponding labels on the connector holder (Figure
26). The slots for the connectors are keyed to prevent
reverse installation, so do not force the connector into
the holder.
2. Carefully pull the excess cable from beneath the -
mounting surface so the connector holder aligns with the
mounting holes on the front of the mounting bracket
(Figure 27).
3. Snap the support plate to the rear of the connector
holder (Figure 28).
4. Insert the connector holder into place and use the two
#6-32 x ¾” (9mm) screws to fasten it to the mounting
bracket (Figure 28).
5. Install the control head by sliding it onto the mounting
bracket until it is fully seated. To remove the unit simply
depress the latch on the rear of the unit and lift (Figure
29).
Your Humminbird is now ready for operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TEST THE INSTALLATION
TEST THE INSTALLATION
Testing should be performed with the boat in the water, however you can initially
confirm basic operation with the boat trailered.
Press POWER once to turn the unit on. There will be an audible chirp when any
button is pressed to confirm the button press. If the unit does not power-up,
ensure the unit is fully seated on the mount and that power is available.
The first screen provides four options: Start-up, Options, Simulator, and
Diagnostic. A message at the bottom of the screen indicates the transducer
connection. If no transducer is detected (or one is not connected), the message
will indicate this and the unit will go into simulator after the initial screen times
out.
Note: the transducer must be submerged in water for reliable transducer
detection.
If a transducer is detected, the unit will enter “Start Up” or normal operation
unless you choose another option. If you do not press any button before the timer
reaches “0”, the normal operation screen is displayed. If the boat is in water,
sonar data appears.
If the bottom is visible on screen with a digital depth readout, the unit is working
properly. Ensure the boat is in water greater than 2’ but less than the depth
capability of the unit and the transducer is fully submerged. Remember the sonar
signal cannot pass through air.
If the unit is working properly gradually increase the boat speed to test high-
speed performance. If the unit-functions well at low speeds but begins to skip or
miss the bottom at higher speeds, the transducer requires adjustment. Refer to
the appropriate transducer installation section for more detail.
Note: it is often necessary to make several incremental transducer
adjustments before optimum high-speed performance is achieved.
Important: For Transom Mount transducer installations, install the third mounting
screw after the final transducer adjustments.
Humminbird · 3 Humminbird Lane · Eufaula, Alabama 36027
Download from Www.Somanuals.com. All Manuals Search And Download.
TESTING THE INSTALLATION
After installing your Pro Flasher and transducer, you are ready to test the installation. Testing
should be performed on the water, since that is the best way to confirm your transducer's
performance.
With your boat in the water, turn the Sensitivity / OnOff control clockwise. You should hear the
disk start to spin and see an area of light at the "0" line on the dial, and another at the number
corresponding to the depth of the water. Turning the Sensitivity control further clockwise
increases the sensitivity of the unit so smaller returns will be displayed.
Increase your boat speed to ensure that the transducer remains in contact with turbulence-free
water at higher boat speeds. All Humminbird depthsounders are designed to work at speeds of
70 MPH or more, however use caution when operating any boat at high speed. High-speed
testing does not apply to portable or trolling motor mounted transducers.
If the Pro Flasher fails to display a bottom return at high speed, first ensure that the depth of the
water is not in excess of the unit's capability. Also, ensure that the unit is fully seated on the
mount, and the cable connectors are correct. (The label on the cable connector matches the label
on the connector holder).
If no light appears when the Power/ Sensitivity control is turned on, the power cable or fuse
terminal may be the problem. If the unit obviously powers up but no bottom information is seen on
the display, the transducer is most likely the problem.
If the Pro Flasher operates well at idle or slow speeds, but loses the bottom at higher
speeds, the transducer is losing intimate contact with the water at higher speeds. If your
transducer is transom mounted, adjusting the running angle or depth of the transducer may solve
the problem. Several test runs and transducer adjustments may be necessary to optimize
transducer performance.
Warning: Due to the "manual" control operation of the Pro Flasher, interference with
sonar products using 200 KHz Frequency is likely.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PRO FLASHER
The Pro Flasher differs from LCD depthsounders in two important ways: Operation of the
unit is completely manual. Adjustment of the sensitivity and noise reject controls, and
interpretation of the information displayed is entirely up to the user. Also, there is no history
retained on-screen. Information displayed is in the form of instantaneous flashes of light on the
dial - targets beneath your boat will appear on-screen for only as long as they are reflecting the
sonar signal.
As with any sonar product, the best way to learn to use the Pro Flasher is to operate in a
familiar area and study the information presented on the display. As you gain experience with the
unit you will be able to quickly analyze the underwater situation, and understand the conditions
that lead to more productive fishing.
The Pro Flasher uses a super-bright LED light source to indicate sonar returns. Since the
display is naturally "light emitting", it is ideal for use at night or in low- light situations. The rubber
lens hood prevents washout in even the brightest sunlight.
As with all Humminbird products, all moving parts are ruggedized for tough shock and
vibration endurance, and special components allow the Pro Flasher to operate at temperatures
more extreme than you are likely to encounter.
Your Pro Flasher may be used on an existing Wide Eye, Wide View or Wide Vision
mounting base. Once mounted it will automatically sense and use the 200 KHz 16° element of
the dual beam transducer. The Pro Flasher mounting base can only be used with the Pro Flasher
unit.
CONTROLS
The Pro Flasher uses two simple controls to vary the display of sonar information:
Sensitivity/On-Off, and Noise Reject.
The Sensitivity/On-Off control serves as both the power switch for the unit as well as the
variable sensitivity control. This is very similar to the volume control on a radio. Increasing the
sensitivity is similar to turning up the volume.
Adjustment of the Sensitivity control is largely a matter of personal taste and experience.
Lower sensitivity settings will present a clean display with only large returns such as the bottom
visible on-screen. Higher sensitivity settings will display progressively smaller signal returns, at
the expense of cluttering the display with information.
The depth of the water will affect the sensitivity setting you choose. Shallow water
requires a lower setting, while deeper water requires a higher setting since some of the sonar
signal will be absorbed or deflected.
Also, the water condition- clear, murky, salt, fresh, etc. will affect the amount of sensitivity
required.
The other control is the Noise Reject. Adjustment of this control is not normally necessary
in the operation of your Pro Flasher. The variable noise reject feature allows you to filter out
electrical interference caused by the boat motor and other electronic devices on your boat.
Noise is normally seen in the form of concentric light patterns that slowly revolve around
the dial. If noise is present, you can reduce it's effect on the Pro Flasher by turning the Noise
Download from Www.Somanuals.com. All Manuals Search And Download.
Reject control slowly clockwise until it is filtered out. If no noise is detected, the control should be
left in the "MIN" position.
WHAT YOU SEE ON THE DISPLAY
A "Zero" line is always present on the dial. This
indicates that the unit is transmitting a signal. Any additional
light displayed indicates a reflected sonar signal. This could be
the bottom or any object between
the surface and the bottom. The depth of the water is
determined by comparing the leading edge of the bottom
return to the number on the appropriate scale (inside or
outside ring). The width of the bottom return and any
surrounding flashes of light can give the user insight into
texture, hardness, ground cover, etc.
Generally, a wider
bottom return indicates a soft
bottom. Soft sand and mud tend
to allow the sonar signal to
penetrate until there is sufficient
density to reflect the signal. The
result is a wider return signal
display. Part of the signal
bounces back immediately from
the surface of the bottom, part of
the signal penetrates slightly.
A hard bottom is generally
displayed as a narrow return. All
of the signal is reflected off the
surface of the bottom
simultaneously, so the returned
signal arrives intact.
Terrain variation within the area of coverage will spread out the bottom representation. It may be
difficult to differentiate a hard sloping bottom from a flat soft bottom.
Download from Www.Somanuals.com. All Manuals Search And Download.
Broken but continuously displayed signals near the bottom return indicate vegetation or ground
cover.
It is often possible to see a "second return" from the
bottom. This is usually seen in shallower water when
the sensitivity is adjusted higher than normal. The
sonar signal is transmitted downward from the boat
and is reflected from the bottom back up. As the Pro
Flasher senses this returned signal, it is displayed on-
screen. The returned signal however is again reflected
off the surface of the water and then the bottom giving
a faint "second return" from the bottom. A second
return is always exactly twice the depth and much
weaker than that of the original return, so it is easy to spot on the dial.
Fish are easy to differentiate on the Pro Flasher because they are usually only displayed briefly.
Only a stationary fish directly under a stationary boat will continue to reflect the sonar signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
A thermocline is the horizontal boundary where significant water temperature differences exist.
When a thermocline exists, it will often tend to reflect sonar signals and is therefore visible on the
display. The thermocline is identifiable because it usually exists over a broad area, and as a
result will appear more continuous than returns from fish.
Download from Www.Somanuals.com. All Manuals Search And Download.
When operating the Pro Flasher in depths over
60', the bottom return will continue to rotate
beyond the "zero" line on the dial. When the
depth is over 60', the returned signal will relate
to the numbers printed on the inside of the dial.
You may notice that increased sensitivity is
necessary due to the signal loss in deeper
water. The Pro Flasher will easily track the
bottom to depths up to 120'.
MAINTAINENCE
Your Humminbird Pro Flasher depthsounder is designed to provide you with years of
trouble-free operation with virtually no maintenance. Follow the simple procedures below to
ensure that your Pro Flasher continues to deliver top performance.
If the unit comes into contact with salt spray, simply wipe the affected surfaces with a
cloth dampened in fresh water.
When cleaning the protective lens, use a chamois and non-abrasive cleaner. Do not wipe
while dirt or grease is on the lens. Be careful to avoid scratching the lens.
If your boat remains in the water for long periods of time, algae and other marine growth
can reduce the effectiveness of the transducer. Periodically clean the face of the transducer with
liquid detergent. Pivoting the transducer up in the bracket may allow better access for inspection
or cleaning.
If your boat remains out of the water for a long period of time, it may take some time to
wet the transducer when returned to the water. Small air bubbles can cling to the surface of the
transducer and interfere with proper operation. These bubbles will dissipate with time, or you may
wipe the face of the transducer with your fingers after the transducer is in the water.
Never leave your Pro Flasher unit in a closed car or trunk - the extremely high
temperatures generated in hot weather can damage the electronics.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not attempt to repair the Pro Flasher yourself. There are no user serviceable parts
inside, and special tools and techniques are required for reassembly to ensure the waterproof
integrity of the housing. Repairs should be performed only by authorized Humminbird technicians.
Many requests for repair received by Humminbird involve units that do not actually need repair. If
you have trouble with your Pro Flasher, consult the following troubleshooting guide before
contacting Humminbird.
1. Nothing happens when I turn the unit on.
Check the power cable connection and fuse. Be sure the power cable is properly connected - red
lead to 12 VDC positive, black lead to negative. Often a fuse can appear to be good when in fact
it is not. Check the fuse with a tester, or replace it if in doubt.
Ensure that the Pro Flasher unit is fully seated on the mount, and the latch is engaged. The
electrical connections to the unit are not made until the unit is securely seated.
2. There multiple flashes at regular intervals.
Check the Sensitivity control, if the control is on maximum sensitivity turn the control
counterclockwise until you get an accurate reading.
3. Unusual or no readings are occurring.
The signal that is reflected back to the transducer from the bottom, or fish, must be strong enough
to produce a good clear flash on the dial. Weak flashes or no flashes indicates one of the
following:
-The Sensitivity control is turned too far counter
clockwise.
-You are positioned above deep decayed vegeta
tion such trees or kelp.
-You are in water over 120 feet deep.
To Correct this problem adjust the Sensitivity control, moving it clockwise toward the maximum
setting.
4. I get gaps in the reading at high speeds.
Your transducer requires adjustment. If the transducer is transom mounted, there are two
adjustments available to you - height, and running angle. Make small adjustments and run the
boat at high speed to determine the effect. It may take several tries to optimize high speed
operation.
5. The bottom reading disappears during a hard turn.
This is normal as the transducer comes out of the water, and will correct itself when the turn is
complete.
6. My unit loses power at high speeds.
Your Humminbird Wide unit has an over-voltage protection which turns the unit off when input
voltage exceeds 17 volts DC. Some outboard motors do not effectively regulate output voltage
Download from Www.Somanuals.com. All Manuals Search And Download.
and can produce electrical output in excess of 17 volts at higher engine speeds. Installation of an
external voltage limiting device will prevent this from occurring.
Download from Www.Somanuals.com. All Manuals Search And Download.
|