Humax Satellite TV System Digital Set Top Box User Manual

Digital Set-Top Box with Irdeto embedded  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety  
This STB has been manufactured to satisfy international safety standards.  
Please read the following safety precautions carefully.  
MAINS SUPPLY : 90 - 250 V AC 50/60 Hz  
OVERLOADING : Do not overload a wall outlet, extension cord or adapter as this may result  
in fire or electric shock.  
LIQUIDS  
: The STB should not be exposed to dripping or splashing, and no objects  
containing liquids, such as base, should be placed on the apparatus.  
CLEANING  
VENTILATION  
: Disconnect the STB from the wall outlet before cleaning.  
Use a light damp cloth (no solvents) to dust the STB.  
: The slots on top of the STB must be left uncovered to allow proper airflow  
to the unit.  
Do not stand the STB on soft furnishings or carpets.  
Do not expose the STB to direct sunlight, nor place it near a heater.  
Do not stack electronic equipment on top of the STB.  
ATTACHMENTS : Do not use any non-recommended attachments, as these maybe  
hazardous or cause damage the STB.  
CONNECTION TO THE SATELLITE DISH LNB  
: Disconnect the STB from the mains before connecting or disconnecting the  
cable from the satellite dish.  
FAILURE TO DO SO CAN DAMAGE THE LNB.  
CONNECTION TO THE TV  
: Disconnect the STB from the mains before connecting or disconnecting the  
cable from the satellite dish.  
FAILURE TO DO SO CAN DAMAGE THE TV.  
EARTHING  
LOCATION  
: The LNB cable MUST BE EARTHED.  
The earthing system must comply with SABS 061.  
: Place the STB indoors to avoid exposing it to lightning, rain or sun.  
GB2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Copyright & Glossary  
Copyright  
VIACCESSTM is a trademark of France Telecom.  
CryptoWorks(TM) is a trademark of Philips Electronics N.V.  
Irdeto is a trademark of Mindport BV.  
Nagravision is a registered trademark of Kudelski S.A.  
Conax is a trademark of Telenor Conax AS.  
Warning  
HUMAX cannot be held responsible for any problems caused by the use of unofficial  
software. The use of software versions other than HUMAX official software will void the  
manufacturer’s warranty. It is advised that only HUMAX formal software be used in all HUMAX  
product ranges.  
Glossary  
Antenna  
A device that collects and radiates electromagnetic waves. This includes a satellite dish and  
a broadband antenna.  
Forward Error Correction (FEC)  
An error control system for data transmission.  
Frequency  
The number of cycles or events per second, expressed in of Hertz(Hz) units.  
Intermediate Frequency (IF)  
A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception.  
Low Noise Block (LNB) Downconverter  
A low noise microwave amplifier and converter which downconverts a range of frequencies to the IF  
range.  
Packet Identifier (PID)  
A set of numbers that identifies transport stream packets containing data from a single data stream.  
Polarisation  
Characteristic of an electromagnetic wave determined by the orientation of the electric field vector.  
Quaternary Phase Shift Keying (QPSK)  
Phase-shift keying in which four different phase angles are used.  
Service  
A channel into which a decoder or TV is tuned.  
Transponder  
An automatic device that receives, amplifies and retransmits a signal on a different frequency.  
GB3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
References  
1. DiSEqC 1.0 Connection  
All our receivers are designed to be DiSEqC 1.0 compatible. This allows multiple antennae  
to be connected to the STB simultaneously.  
If you have two or more fixed antennae or LNBs, you can use a DiSEqC 1.0 switch.  
1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A DiSEqC switch input  
connector.  
2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B DiSEqC switch in  
put connector.  
3. Do the same for the other LNBs.  
4. Connect one end of a Coaxial cable to the RF DiSEqC switch output connector and the  
other end to the LNB IN socket on the STB.  
2. DiSEqC 1.2 Connection  
Please refer to page GB46.  
3. Connecting a Satellite antenna  
You can connect either a single satellite antenna directly to the digital receiver or several  
antennae via the converter box or multi-feed equipment LNB.  
You can connect a further Sat-receiver (for example analogue) to the common antenna  
equipment receiver that has satellite signals.  
4. Loop Via  
If you have another analogue or digital STB and you wish to use the same LNB, then you  
can connect it via the loop via. Connect one end of a Coaxial cable to the LNB OUT  
on the STB and connect the other end to the LNB IN on your second STB.  
GB4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Software Upgradeing  
The HUMAX digital set-top box is a highly sophisticated product-incorporating one of the  
best software applications.  
Whenever a problem is found with this software or extra functions or enhanced  
applications are added, the software in the equipment must be upgraded.  
In order to maintain correct product performance, it is essential to have the most  
Up-to-date software. The latest news and releases on software versions may be found at  
the HUMAX website - http://www.humaxdigital.com.  
It is recommended that users register with HCSA (HUMAX Customer Service Area) and  
periodically check the availability of software upgrade.  
There are three methods for upgrading the software:  
(a) set-top box to set-top box download (copies the software from the main unit into the slave  
unit);  
(b) PC to set-top box download (downloads the software directly from the PC to the model  
requiring upgrading);  
(c) OTA over-the-air (downloads the software, where the manufacturer reserves the right to  
decide when and where to release via the satellite system).  
Over The Air (OTA) is simply another alternative for downloading software versions.  
However, the manufacturer reserves the right to decide when and where this software  
upgrade takes place by "beaming" the latest software versions over the air via satellite  
systems. Note that OTA is limited to certain geographical regions only, mainly due to  
different satellites having different footprints (areas where the signal can be received).  
SUSS (TM) is an official trademark and logo for HUMAX loader software to perform OTA.  
The software upgrade via the satellite system can only occur under the following  
circumstances:  
1) the equipment should have appropriate loader software;  
2) the manufacturer decides to release software downloading via a designated satellite  
system;  
3) the equipment must be properly "tuned" to the same satellite as the one used by the  
manufacturer.  
GB5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STB Connections  
Front Panel  
1
2
3
4
5
6
8
7
1
2
3
4
5
6
7
STANDBY  
Press to switch between Operation and Standby modes.  
TV/RADIO  
Press to switch between TV and Radio modes.  
P-  
Use to change services down.  
P+  
Use to change services up.  
STANDBY LED (RED)  
Indicates that the STB is under standby.  
TV LED (GREEN)  
The LED light goes on when in TV mode.  
RADIO LED (YELLOW)  
The LED light goes on when in RADIO mode.  
8 SLOT  
For a CA Module with a smart card.  
GB6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel  
1
LNB IN  
Use to connect an antenna.  
2 LNB OUT  
Use when connecting to another STB.  
RS-232C  
3
Use when connecting to your PC.  
4 TV SCART  
For the TV audio/video input.  
5 VCR SCART  
For the VCR.  
6
AUDIO OUTPUT  
Audio signal from your STB to VCR or TV.  
GB7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STB Connections  
There are several ways of connecting the STB to your existing Audio/TV system.  
For best results, we recommend using one of the following set-ups:  
TV only  
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and  
the other end to a SCART socket on your TV.  
2. Connect the coaxial cable from the LNB to the LNB IN socket on the STB.  
TV with VCR  
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB  
and the other end to a SCART socket on your TV.  
2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB  
and the other end to a SCART socket on your VCR.  
3. Connect the coaxial cable from the LNB to the LNB IN socket on the STB.  
With a Hi-fi System  
1. Connect an RCA/Cinch stereo cable from the AUDIO L,R sockets on the back of the STB  
to the LINE, AUX, SPARE OR EXTRA input sockets on your Hi-fi system.  
GB8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV with VCR and Motorised System (DiSEqC 1.2)  
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and  
the other end to a SCART socket on your TV.  
2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB  
and the other end to a SCART socket on your VCR.  
3. Connect the coaxial cable from the LNB of your motorised system(DiSEqC 1.2 Motor)  
to the LNB IN socket on the STB.  
GB9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Unit  
TV/RADIO  
SOURCE  
STANDBY  
NUMERIC BUTTONS  
FAV (FAVOURITE)  
GREEN  
GUIDE  
YELLOW  
YELLOW  
BLUE  
GREEN  
RED  
BLUE  
RED  
OK  
CURSOR  
EXIT  
P-/P+  
V-/V+  
RCL (RECALL)  
MENU  
i (INFORMATION)  
FREEZE  
HELP  
MUTE  
+
OPT (OPTION)  
GB10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
12  
13  
TV/RADIO  
STANDBY  
Press to switch between Operation mode and  
Standby mode.  
Press to switch between TV and Radio modes.  
2 SOURCE  
Press to select the TV/SAT mode.  
GUIDE  
Press to display the TV/Radio Electronic Programme  
Guide  
3 NUMERIC BUTTONS  
Press to select a service, enter your PIN code or  
number on a menu.  
14 YELLOW  
Press to select a Service Network in the Service  
List. This button functions in the same way as the  
YELLOW button icon on a menu.  
4 FAV (FAVOURITE)  
Press to see the current service configuration  
or edit during A/V play.  
15  
BLUE  
Press to select a Service Alphabet in the Service  
List. This button functions in the same way as the  
BLUE button icon on a menu.  
5 GREEN  
Press to select a Service Favourite in the Service  
List. This button functions in the same way as the  
GREEN button icon on a menu.  
16 CURSOR  
Press to move the highlight bar for selecting  
options on the menus.  
This button can be used to change services  
(up/down) and increase or decrease the audio  
volume (left/right).  
6 RED  
Press to select a Service All in the Service List.  
This button functions in the same way as the RED  
button icon on a menu.  
OK  
7
17 EXIT  
Press to display the service list. This button can be  
used to select the item on the menus.  
Press to return to the previous menu or screen.  
18 V-/V+  
8 P-/P+  
Volume up/down buttons.  
Programme up/down buttons.  
Press to increase or decrease the volume.  
Press to move to the next or previous service.  
Press to move up or down pages on a menu.  
19  
RCL (RECALL)  
Press to select the service previously viewed.  
9
MENU  
Press to display the Main Menu on the screen  
or return to the screen from a sub menu screen.  
20 HELP  
Press to display the help box on the screen.  
10 i (INFORMATION)  
Press to display the programme information box  
on the screen.  
MUTE  
21  
22  
Press to cut the sound off temporarily.  
FREEZE  
11  
+
OPT (OPTION)  
Press once to freeze the screen picture.  
Press again to return to normal mode.  
Press to enter the sub menu for selecting  
Soundtrack and Subtitle.  
This button can be used to reserve a  
programme in the TV Guide.  
Please note : The design of the Remote Control Unit may be changed without advance notice.  
GB11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function Guide  
Information Box (I-Plate)  
The detailed information on a service and its event is automatically  
displayed at the bottom of the screen (I-Plate) whenever a service  
changes. To obtain this information when watching a service, press  
thei (  
) button. If you press the i (  
) button again while the  
I-Plate is displayed, the I-Plate disappears.  
The I-Plate is divided into a “service information” part and an “event  
information” part.  
Service Part  
The service information is situated on the left side of the I-Plate and  
consists of the following items:  
• Current Time, Dolby Digital Symbol if there is an available Dolby  
service.  
• Service name, Service Number, icon.  
• Subtitle/Teletext/Scrambling symbol displayed according to the  
service attributes.  
• Progressive Signal Quality bar.  
Event Part  
The event information is situated on the right side of the I-Plate and  
consists of the following items:  
• Event name and, duration time of the event.  
• Description of the event, status of the reserved event.  
There are two types of event information, present event  
information and following event information.  
If the following one is available, the icon is displayed.  
To switch between the present and following ones, proceed as  
follows,  
1. Activate the I-Plate using the i (  
) button.  
2. If the present event information is available, it is displayed on the  
I-Plate.  
3. If the following event information is available, the  
displayed.  
icon is  
4. Press the button to switch to the following event information.  
5. Press the button to return to the present event information.  
If the present one is not available, the icon is not displayed  
and cannot return to from the following one.  
GB12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you press the HELP (  
) button while the I-Plate is displayed,  
the detailed description of the event will be displayed on the help  
window instead of help messages. If there is no available data for  
the detailed description on the air, the help message is displayed on  
the help window instead.  
Changing Services  
There are several ways to change a service.  
• Use the NUMERIC buttons: key in the service number using the  
NUMERIC buttons and press the OK (  
) button. If the OK (  
)
button is not pressed, the service is automatically changed to the  
service number keyed in after about 5 seconds.  
• Use the  
sequentially if the  
• Use the buttons: the service is changed up/down  
sequentially if the button is pressed.  
• Use the service list or Guide list: refer to the following description.  
buttons: the service is changed up/down  
button is pressed.  
• Use the RCL (  
when the RCL (  
) button: return to the latest viewed service  
) button is pressed.  
There are two types of service, TV and RADIO.  
To switch between them, press the TV/RADIO button.  
To change a service in the service list or guide list, proceed as  
follows:  
1. Activate the service list or guide list.  
(Refer to the following GB15, 17 pages on how to activate them)  
2. Select the desired service using the  
button.  
3. Press the OK (  
) button, and the service is changed to the  
desired one.  
Teletext Service  
The TELETEXT ( ) icon appears on the I-Plate if there is  
available teletext data in the service.  
(NOTE: The TV supports the teletext decoder internally for  
watching it, since the teletext data is decoded by the TV.)  
Volume Control  
To adjust the volume level, use the  
button or the  
button.  
To mute the audio, press the MUTE (  
) button. To recover the  
audio level, press the MUTE (  
) button again, or the ,  
button.  
GB13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function Guide  
Soundtrack  
To change the audio language in the current service, proceed as  
follows:  
+
1. Press the OPT  
(
) button and select the Soundtrack item.  
2. Press the  
languages.  
button to activate the list of supported audio  
3. Select the desired audio language in the list using the  
keys.  
4. Select the audio mode (mono, stereo, Dolby) in the desired audio  
language using the  
buttons.  
5. Press the OK (  
) button to confirm the change,  
or the EXIT (  
) button to cancel the change.  
The selected audio language is preserved regardless of the  
change of service.  
If the selected audio language is invalid from some reason, the  
default audio language will be selected. (The default audio language  
can be set on the Language Setting in the Main menu.)  
If an audio language is encoded by Dolby Digital, the Dolby Digital  
Symbol will appear in the list of audio languages.  
NOTE: The Dolby decoder with optical port shall be connected  
externally to decode the Dolby Digital audio.  
Subtitle  
If there is a subtitle service available on the air, the subtitle icon (  
will appear in the I-Plate.  
)
To select the subtitle language, proceed as follows:  
+
1. Press the OPT  
(
) button and select the Subtitle item.  
2. Press the button to activate the list of supported subtitle  
languages.  
3. Select the desired subtitle language in the list using the  
keys.  
4. Press the OK (  
) button to confirm the change or press the  
EXIT ( ) button to cancel the change.  
GB14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service List  
There are four service list types: All Service, Favourite Service,  
Network Service and Alphabetical Order Service.  
There is also a Configuration Service menu to change the  
attributes of each service in the list.  
In the service list, some buttons are used to switch the service list  
type or select the service.  
buttons: Used to move the cursor up/down in the  
service list.  
buttons: Used to move the cursor left/right in the  
service list.  
RED button: Used to select the All type Service.  
GREEN button: Used to select the Favourite type Service.  
YELLOW button: Used to select the Network type Service.  
BLUE button: Used to select the Alphabetical Order Service.  
Configuration Service  
To change the attributes of a service, proceed as follows:  
1. Change to the service whose attributes are to be changed using  
the  
,
or other method.  
) button.  
2. Press the FAV (  
The Service Configuration Box then appears on the screen.  
3. Use the buttons to select the desired one among the  
attribute items (Favourite, Lock, Skip and Delete) in the Service  
Configuration Box.  
4. Use the  
buttons to enable/disable “LOCK”, “SKIP” or  
“DELETE” to select the desired favourite group. When done,  
press the OK (  
) button. To cancel, press the EXIT (  
)
button.  
All Service  
The All Service list is a normal one, where the service list is  
organised according to the order in which services are searched.  
(The latest service will be added at the end of the service list.)  
To select the “All Service” list, press the RED button with the  
service list displayed.  
If the RED button is pressed again in the All mode Service,  
the service list toggles between Simple List and Advanced List.  
GB15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function Guide  
Service Favourite  
Services can be grouped in the favourite list. To add a service to a  
group in the favourite list, the Configuration Service box or the  
Service Organising menu in the main menu can be used.  
(Refer to the related item for a more detailed description).  
To select the “Favourite Service” list, press the GREEN button with  
the service list displayed.  
Service Network  
In the Network Service mode, the service list is organised according  
to the network to which a service belongs.  
To select the “Network Service” list, press the YELLOW button with  
the service list displayed.  
Whenever the YELLOW button is pressed in the “Network Service”  
mode, the cursor will be toggled between the network name column  
and the service name column.  
When the cursor is in the network name list, the desired network  
can be selected using the  
button.  
All services belonging to the selected network will be listed in the  
service name column.  
Service Alphabetical  
In the Alphabetical Service mode, the list of services is given  
alphabetically according to the service name.  
To select the Alphabetical Service list, press the BLUE button with  
the service list displayed.  
Whenever the BLUE button is pressed in the Alphabetical Service  
list, the cursor will be toggled between the alphabet character  
column and the service name column.  
When the cursor is in the alphabet character list, the desired  
alphabet character can be selected using the  
button.  
All services with the selected alphabet character as a first character  
in the service name will be listed in the service name column.  
GB16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
The Main menu contains the TV Guide, Parental Control, Installation  
and Utility menus. (For more detailed information about menu  
structure, please refer to the Menu Map page at the end of the  
User’s Manual.)  
1. TV Guide  
The TV Guide is useful when all the services are being navigated,  
since it offers all possible viewing options.  
The TV Guide supplies the following information:  
• Start/end time of all available services.  
• Short description of all available services.  
• Extended description of all available services.  
For easy navigation, the TV Guide supplies 4 modes: Now, Weekly,  
Reserved and Quick.  
2. Parental Control  
Parental Control offers all items related to the PIN code and  
parental control.  
• Censorship classification: the parental control level can be  
specified.  
• Change PIN: the PIN code can be modified.  
The PIN code is an important password when reconfiguring the  
STB, locking some services and giving access to the locked  
services.  
3. Installation  
Installation offers the following functions:  
• Reconfiguration of system settings.  
• Organisation of service list.  
• Search of services.  
• System status.  
• Information on the conditional access system.  
• Restoration to the default setting.  
4. Utility  
Utility offers useful functions such as:  
• Calendar.  
• Biorhythm.  
GB17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
1. TV Guide  
The TV Guide offers more detailed information on the service (both  
TV and Radio services) such as start/end time, short description  
and extended description. The service can be reserved in the TV  
Guide.  
To activate the TV Guide menu, do one of the following:  
• Press directly the GUIDE (  
) button  
• Select the TV Guide in the Main menu  
If the TV/RADIO (  
) button is pressed with the TV Guide  
displayed, the service list is toggled between the TV service and  
Radio service.  
There are 4 modes in TV Guide: NOW, WEEKLY, RESERVED and  
QUICK.  
• NOW: This mode displays information on the present services  
and following services.  
• WEEKLY: This mode displays information on all the services  
for one week.  
• RESERVED: This mode displays information on all the services  
reserved by a user.  
• QUICK: This mode displays information on the proceedings  
of the current service while a full video screen is displayed  
on the background.  
The colour buttons are used to change the mode of the TV Guide.  
RED button: Used to select NOW mode.  
GREEN button: Used to select WEEKLY mode.  
YELLOW button: Used to select RESERVED mode.  
WHITE button: Used to select QUICK mode.  
GB18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Now mode  
The NOW mode displays information on the present services  
and following services. The information includes service name,  
event name and start/end time of an event.  
To activate the NOW mode and surf the services, proceed as  
follows:  
1. Activate the TV Guide menu using the GUIDE (  
) button or  
via the Main menu.  
2. Press the RED button to select the NOW mode. The NOW  
mode contains a service list with information on the left side of  
the screen, and the video is zoomed out on the right side of the  
screen.  
3. To watch the desired service, use the  
press the OK ( ) button, or use the  
button to select it and  
button to select it.  
(The service list can be paged-up/down using the  
button.)  
The service then plays in the video zoomed out and the  
associated information is displayed at the bottom of the screen.  
To reserve a programme in the NOW mode, proceed as follows:  
1. Use the  
service.  
button or  
button to select the desired  
+
2. If the desired service is selected, press the OPT  
(
) button to  
reserve it.  
3. There are two modes in the reservation menu: “Daily” and  
“Weekly”. “Daily” means that a service event will play daily,  
and “Weekly” means that a service event will play weekly.  
GB19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Weekly mode  
The WEEKLY mode displays information about all the services that  
will be transmitted over a week.  
The information includes service name, event name and start/end  
time of the event.  
To activate the WEEKLY mode, proceed as follows:  
1. Activate the TV Guide menu using the GUIDE (  
via the Main menu.  
) button or  
2. Press the GREEN button to select WEEKLY mode.  
To reserve a service event, proceed as follows:  
1. Select the desired service event using the  
button.  
+
2. Press the OPT  
(
) button to reserve the event.  
If the selected event is currently playing, there are two modes in the  
reservation menu: “Daily” and “Weekly”.  
If the selected event is playing in the future, there are three modes  
in the reservation menu: ”Once”, “Daily” and “Weekly”.  
In “Daily” mode, a service event will play daily.  
In “Weekly” mode, a service event will play weekly.  
In “Once” mode, a service event will play only once.  
If the OK (  
appears. The service can be changed in this box using the  
and the OK ( ) buttons.  
) button is pressed, the small box with a service list  
GB20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reserved mode  
The RESERVED mode displays the services which have been  
reserved.  
In this mode, the reservation mode can be changed.  
The service can also be removed from the reservation list.  
To change the mode or remove a service event of, proceed as  
follows in RESERVED mode:  
• Activate the TV Guide menu using the GUIDE (  
) button or  
via the Main menu.  
• Press the YELLOW button to select the RESERVED mode.  
• Select the desired service event using the buttons.  
) to activate the reservation menu.  
+
• Press the OPT  
(
Next, change the mode or remove the event.  
Quick mode  
The QUICK mode displays information on the proceedings  
of the current service while a full video screen is displayed in the  
background.  
To activate the QUICK mode, proceed as follows:  
1. Activate the TV Guide menu using the GUIDE (  
via the Main menu.  
) button or  
2. Press the BLUE button to select QUICK mode.  
3. Select the desired service using the  
4. Select the desired event (present event or following event) using  
the button.  
button.  
The time line consists of three blocks, each block with a 30-minute  
time-line.  
The blue vertical line indicates the current time in the time-line.  
The black and white bar indicates the start/end time of the event in  
time-line.  
(The bar will be black depending on the time the event took place.)  
GB21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
2. Parental Control  
In the Parental Control menu, it is possible to change the Parental  
Guidance Rating and the PIN code.  
To set the Parental Guidance Rating, proceed as follows:  
1. Activate the Parental Control menu via the Main menu.  
(To activate it, the PIN code should be entered).  
2. Select the Censorship classification item using the  
3. Select the desired Parental Guidance Rating using the  
button.  
button.  
4. The Parental Guidance Rating is given as age-based numbers,  
“no block”, “10”, “13”, “16”, “18” and “total block”.  
5. Press the OK (  
) button to confirm the change.  
0 0 0 0  
** The default PIN code is  
.
To change the PIN code, proceed as follows:  
1. Activate the Parental Control menu via the Main menu.  
(To activate it, the PIN code should be entered).  
2. Select the Old PIN code menu using the  
button.  
3. Enter the Old PIN code using numeric buttons. When four digits  
have been entered, the cursor will automatically be moved to the  
New PIN code menu.  
4. Enter the new PIN code in the New PIN code menu. When four  
digits have been entered, the cursor will automatically be moved  
to the Verify Changed PIN Code menu.  
5. Enter the new PIN code again to verify it. If it is correct, then the  
new PIN code will be saved. If incorrect, then the message  
“PIN code mismatch” will be displayed.  
3. Installation  
The INSTALLATION menu supplies the following functions:  
• Configuration of miscellaneous functions such as  
Language Setting, Time Setting, etc.  
• Organization of Service List  
• Search for services  
• Information on STB  
GB22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-1. System Setting  
This sub-menu supplies the miscellaneous functions.  
Language Setting  
The Language Setting menu supplies Menu Language, Audio  
Language and Subtitle Language.  
Menu Language  
The menu language is a language used in the text of the menu.  
To change the menu language, proceed as follows:  
1. Activate the Language Setting menu via the Main menu.  
2. Select the Menu Language using the  
OK ( ) button.  
3. When the small box with the supported language list appears,  
select the desired language using the button.  
button and press the  
4. If the desired menu language is selected, press the OK (  
)
button to confirm.  
Audio Language  
The audio language is a language selected as a default  
audio when a service is playing. It is also possible to change the  
audio language via the Soundtrack menu in the Option List menu.  
To change the audio language, proceed as follows:  
1. Activate the Language Setting menu via the Main menu.  
2. Select the Audio Language menu using the  
press the OK ( ) button.  
3. When the small box with the supported language list appears,  
select the desired language using the button.  
button and  
4. If the desired audio language is selected, press the OK(  
)
button to confirm.  
GB23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Subtitle Language  
The subtitle language is a language selected as a default  
when a service with subtitles is playing. It is also possible to change  
the subtitle language via the Soundtrack menu in the Option List  
menu.  
To change the subtitle language, proceed as follows:  
1. Activate the Language Setting menu via the Main menu.  
2. Select the Subtitle Language menu using the  
press the OK ( ) button.  
3. When the small box with the supported language list appears,  
select the desired language using the button.  
4. If the desired subtitle language is selected, press the OK  
) button to confirm it.  
button and  
(
Time Setting  
The Time Setting menu supplies the following functions:  
• Set the current time.  
• Disable/Enable the wake-up timer.  
• Set the wake-up service. The wake-up service is a service  
that will play when STB starts after a wake-up timer has expired.  
• Disable/Enable the sleep timer.  
Current Time  
To set the current time, proceed as follows:  
1. Activate the Time Setting menu via the Main menu.  
2. Select the Current Time item using the  
button.  
3. Set the current time using the  
increases by 30 minutes when the  
decreases by 30 minutes when the  
button (the current time  
button is pressed and  
button is pressed.)  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
GB24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wakeup Time  
To disable or enable/set the wake-up timer, proceed as follows:  
1. Activate the Time Setting menu via the Main menu.  
2. Select the Wakeup Time item using the  
button.  
3. To disable the wake timer, set to “Disable” using the  
button.  
4. To enable and set the wakeup timer, set the item to “00:00” using  
the button. (The numeric mark, “0..9” appears on the right of the  
Wake Time item). Set the desired wake-up time using  
the NUMERIC buttons.  
5. Press the OK (  
) or EXIT (  
) button to confirm.  
Wakeup Service No.  
To set the wake-up service, proceed as follows:  
1. Activate the Time Setting menu via the Main menu.  
2. Select the Wakeup Service No. item using the  
button.  
3. Set the service number using the  
buttons.  
button or NUMERIC  
The service type (TV or RADIO) can be changed using the  
TV/RADIO ( ) button. The service name is also displayed  
under the Wakeup Service No. item.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
Sleep Time  
To disable or enable/set the sleep timer, proceed as follows:  
1. Activate the Time Setting menu via the Main menu.  
2. Select the Sleep Time using the  
3. To disable the sleep timer, set the item to “Disable”  
using the button.  
4. To enable and set the sleep timer, set the item to “00:00” using  
the button. (The numeric mark, “0...9” appears on the right  
button.  
of the Sleep Time item) In this state, set the desired sleep time  
using the NUMERIC buttons.  
5. Press the OK (  
) or EXIT (  
) button to confirm.  
GB25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
A/V Output Setting  
The A/V Output Setting menu supplies menus that configure the  
functions related to Audio and Video output.  
• Configure the Video output of TV SCART as CVBS, S-VIDEO or  
RGB mode.  
• Configure the Audio output of TV SCART and RCA (Cinch) Jack  
as Mono or Stereo mode.  
• Configure the screen aspect ratio (4:3 or 16:9) of the TV connected  
to STB.  
• Configure the video display format (Centre or Letter-box) on the  
TV.  
• Configure the NTSC mode. There are two NTSC modes, NTSC  
3.58 and NTSC 4.43. The NTSC 3.58 is more popular.  
According to the TV type, select the suitable NTSC mode.  
Video Output (CVBS/S-Video/RGB)  
To configure the Video output mode of TV SCART, proceed as  
follows:  
1. Activate the A/V Output Setting via the Main menu.  
2. Select the Video Output item using the  
3. Select the desired video output using the  
button.  
button. There are  
three modes: CVBS, S-VIDEO and RGB mode.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
Audio Output  
To configure the audio output mode of TV SCART and RCA jack,  
proceed as follows:  
1. Activate the A/V Output Setting via the Main menu.  
2. Select the Audio Output item using the  
3. Select the desired audio output using the  
button.  
button.  
There are two modes: STEREO and MONO.  
4. Press the OK ( ) or EXIT ( ) button to confirm.  
GB26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screen Mode  
To configure the TV screen mode, proceed as follows:  
1. Activate the A/V Output Setting via the Main menu.  
2. Select the Screen Mode item using the  
button.  
3. Select the desired TV screen mode according to the connected  
TV using the  
4. Press the OK (  
button. There are two modes: 16:9 and 4:3.  
) or EXIT ( ) button to confirm.  
Display Format  
To configure the display format on the TV, proceed as follows:  
1. Activate the A/V Output Setting via the Main menu.  
2. Select the Display Format item using the  
3. Select the desired display format depending on the TV using  
the button. There are two mode pairs depending on the type  
button.  
of TV. If the TV supports only the 4:3 mode, there is one mode  
pair such as Centre and Letter-Box mode. If the TV supports the  
16:9 mode, there is another mode pair such as Full and  
Pillar-box mode.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
The display format can be appropriately configured according to the  
selected Screen Mode.  
If the Screen Mode is selected as 4:3, there are two modes, Centre  
and Letter-box in the display format. If the video is formatted as  
16:9 and the display format selected as Centre mode, the right and  
left portions of the video are cut off to fit the 16:9 video into the 4:3  
TV screen. If the video is formatted as 16:9 and the display format  
selected as Letter-box mode, the video is vertically shrunk to fully  
display on the 4:3 TV screen. In that state, the top and bottom of  
the TV screen are blacked out. If the video is formatted as 4:3, the  
display format is not applicable when the screen mode is selected  
as 4:3.  
GB27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
If the Screen Mode is selected as 16:9, there are two modes, Full  
and Pillar-box, in the display format. If the video is formatted as 4:3  
and the display format selected as Full mode, the video is expanded  
to fit the 4:3 video into the 16:9 TV screen. If the video is formatted  
as 4:3 and the display format selected as Pillar-box mode, the video  
is displayed on the centre of the 16:9 TV screen without  
modification. The right and left sides of the TV screen are blacked  
out. If the video formatted as 16:9, the display format is not  
applicable when the screen mode is selected as 16:9.  
NTSC Mode  
To configure the NTSC mode on the TV, proceed as follows:  
1. Activate the A/V Output Setting via the Main menu.  
2. Select the NTSC Mode item using the  
3. Select the desired NTSC Mode using the  
button.  
button.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
Other Setting  
The Other Setting menu supplies the following functions:  
• Set the level of OSD transparency. There are two levels:  
opaque 50% transparent.  
• Set the duration time of the Info. Box display. The duration time  
can be set from 0 to 20 seconds.  
• Set the Menu Mode, which changes the menu format according to  
the video format (NTSC, PAL, Auto). If the TV supports only the  
NTSC format, set the menu mode to NTSC. If the TV supports  
only the PAL format, set the menu mode to PAL. If the menu mode  
is set at Auto, the menu format is automatically changed  
according to the format of the decoded video.  
GB28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD Transparency  
To set the OSD transparency, proceed as follows:  
1. Activate the Other Setting menu via the Main menu.  
2. Select the OSD Transparency item using the  
button.  
3. Select the desired level between Opaque and Transparent  
modes using the  
button.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
Info. Box Display Time  
To set the duration time of Info. Box display, proceed as follows:  
1. Activate the Other Setting menu via the Main menu.  
2. Select the Info. Box Display Time using the  
3. Select the desired duration time using the  
button.  
button.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
Menu Mode  
To set the menu mode, proceed as follows:  
1. Activate the Other Setting menu via the Main menu.  
2. Select the Menu Mode item using the  
3. Select the desired menu mode using the  
button.  
button.  
4. Press the OK (  
) or EXIT (  
) button to confirm.  
3-2 Service Organising  
The Service Organising menu supplies several organising methods:  
• Organisation of TV services,  
• Organisation of Radio services,  
• Organisation of services sorted by a network name,  
• Deletion of services belonging to a satellite.  
GB29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Organise TV Services  
The Organise TV services menu supplies two organisation  
methods: Organise All Services and Organise Favourites.  
Each offers a method of organisation with its own characteristics.  
Organise All Services  
The services are sorted according to the service number in the  
Organise All Services menu.  
Each service can be deleted from the TV service list, moved to  
another position, locked or skipped when zapping the service.  
To delete the service from the service list, proceed as follows:  
1. Activate the Organise All Services menu for TV services via  
the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
button can be used to page up/down the service list.  
3. Press the RED button while the desired service is selected.  
The service is then marked in grey.  
4. Mark all the desired services using the above method. If a service  
is to be left unmarked, select it and press the RED button  
again (i.e. the RED button toggles the grey mark.)  
5. Press the OK (  
) button to delete all the marked services,  
) button to cancel.  
otherwise press the EXIT (  
To move a service to another position in the service list, proceed as  
follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
3. Press the GREEN button while the desired service is selected.  
The icon then appears beside the service number.  
4. Move the selected service to the desired position using the  
button can be used to page up/down the service list.  
button. The  
button can be used to move across  
a page in the service list.  
5. Press the OK (  
) or GREEN button to confirm, otherwise press  
) button to cancel.  
the EXIT (  
GB30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To lock a service in the service list, proceed as follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
3. The  
4. Press the YELLOW button. The  
of the service name. If the YELLOW button is pressed again,  
the icon disappears.  
button can be used to page up/down the service list.  
icon then appears at the end  
5. Press the OK (  
or the EXIT (  
) button to confirm  
) button to cancel.  
To skip the service when zapping it, proceed as follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
3. The  
4. Press the BLUE button. The  
the end of the service name. If the BLUE button is pressed  
button can be used to page up/down the service list.  
icon then appears at  
again, the  
5. Press the OK (  
or the EXIT (  
icon disappears.  
) button to confirm  
) button to cancel.  
GB31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Organise Favourite Services  
The services are sorted according to favourite groups in the  
Organise Favourites menu.  
There are three columns: the favourite group column,  
the favourite list column and the service list column containing  
services not belonging to any favourite group.  
The Organise Favourites menu supplies the following functions:  
• Add a service to a favourite group.  
• Remove a service from a favourite group.  
• Move a service to another position in a favourite list.  
• Lock a service in a favourite list.  
• Skip a service in a favourite list when zapping the service.  
To add a service to a favourite group, proceed as follows:  
1. Activate the Organise Favourite menu for TV services via the  
Main menu.  
2. Move the cursor to the favourite group column using the  
button. If the favourite group column is selected, the column is  
highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the service list column using the  
button.  
If the service list column is selected, the column is highlighted.  
5. Select the desired service in the service list column using the  
button, then press the OK (  
) button to move it.  
6. Press the EXIT ( ) button to confirm.  
To remove a service from a favourite group, proceed as follows:  
1. Activate the Organise Favourites menu for TV services via the  
Main menu.  
2. Move the cursor to the favourite group column using the  
button. If the favourite column is selected, the column is  
highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the favourite list column using the  
If the favourite list column is selected, the column is highlighted.  
5. Select the desired service in the favourite list column using the  
button and press the RED button to mark the service.  
button.  
6. Press the OK (  
) button to remove the marked services from a  
favourite list.  
GB32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To skip or lock a service in a favourite list, proceed as follows:  
1. Activate the Organise Favourites menu for TV services via the  
Main menu.  
2. Move the cursor to the favourite group column using the  
button.  
If the favourite column is selected, the column is highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the favourite list column using the  
If the favourite list column is selected, the column is highlighted.  
5. Select the desired service in the favourite list column using the  
button and press the YELLOW/BLUE button to lock/skip the  
service. To undo the action, press the button again.  
button.  
6. Press the OK (  
) button to confirm.  
Organise Radio Services  
Organise All Services  
The services are sorted according to the service number in the  
Organise All Service menu.  
Each service can be deleted from the RADIO service list, moved to  
other position, locked or skipped when zapping the service.  
To delete the service from the service list, proceed as follows:  
1. Activate the Organise All Services menu for RADIO services  
via the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
button can be used to page up/down the service list.  
3. Press the RED button. The service is then marked in grey.  
4. Mark all desired services using the above method. If a service is  
to be left unmarked, select it and press the RED button again.  
The RED button toggles the grey mark.  
5. Press the OK (  
or press the EXIT (  
) button to delete all marked services.  
) button to cancel.  
GB33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
To move a service to another position in the service list, proceed as  
follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
3. Press the GREEN button with the desired service selected.  
The icon then appears beside of the service number.  
4. Move the selected service to the desired position using the  
button can be used to page up/down the service list.  
button. The  
button can be used to move across a  
page in the service list.  
5. Press the OK (  
) or GREEN button to confirm,  
otherwise press the EXIT (  
) button to cancel.  
To lock the service in the service list, proceed as follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
3. Press the YELLOW button. The  
of the service name. If the YELLOW button is pressed again,  
the icon disappears.  
4. Press the OK ( ) button to confirm.  
Otherwise press the EXIT ( ) button to cancel.  
button can be used to page up/down the service list.  
icon then appears at the end  
To skip the service in zapping the service, proceed as follows:  
1. Activate the Organise All Services menu via the Main menu.  
2. Select the desired service in the service list using the  
button.  
The  
button can be used to page up/down the service list.  
icon then appears at the end of  
3. Press the BLUE button. The  
the service name. If BLUE button is pressed again, the  
icon  
disappears.  
4. Press the OK (  
or press the EXIT (  
) button to confirm  
) button to cancel.  
GB34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Organise Favourite Services  
The services are sorted according to the favourite groups in the  
Organise Favourites menu. There are three columns: the favourite  
group column, the favourite list column and the service list column  
containing services that do not belong to any favourite group.  
The Organise Favourites menu supplies the following functions:  
• Add a service to a favourite group.  
• Remove a service from a favourite group.  
• Move a service to another position in a favourite list.  
• Lock a service in a favourite list.  
• Skip a service in a favourite list when zapping the service.  
To add a service to a favourite group, proceed as follows:  
1. Activate the Organise Favourites menu for RADIO services via  
the Main menu.  
2. Move the cursor to the favourite group column using the  
button. If the favourite group column is selected, the column is  
highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the service list column using the  
button.  
If the service list column is selected, the column is highlighted.  
5. Select the desired service in the service list column using the  
button. The  
service list. Then press the OK (  
6. Press the EXIT ( ) button to confirm.  
button can be used to page up/down the  
) button to move it.  
GB35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
To remove a service from a favourite group, proceed as follows:  
1. Activate the Organise Favourite menu for RADIO services via  
the Main menu.  
2. Move the cursor to the favourite group column using the  
button.  
If the favourite column is selected, the column is highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the favourite list column using the  
button.  
If the favourite list column is selected, the column is highlighted.  
5. Select the desired service in the favourite list column using the  
button (the  
button can be used to page up/down the  
service list) and press the RED button to mark the service.  
6. Press the OK (  
) button to remove the marked services from a  
favourite list.  
To skip or lock a service in a favourite list, proceed as follows:  
1. Activate the Organise Favourite menu for RADIO services via  
the Main menu.  
2. Move the cursor to the favourite group column using the  
button.  
If the favourite column is selected, the column is highlighted.  
3. Select a favourite group in the favourite group column using the  
button.  
4. Move the cursor to the favourite list column using the  
button.  
If the favourite list column is selected, the column is highlighted.  
5. Select the desired service in the favourite list column using the  
button (the  
button can be used to page up/down the  
service list) and press the YELLOW/BLUE button to lock/skip the  
service. Press the button again to undo the action.  
6. Press the OK (  
) button to confirm.  
GB36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Organise Networks  
The Organise Networks menu supplies the following functions:  
• Delete the network. This will delete all services belonging to the  
network.  
• Move/reorder the networks in the network list.  
• Sort the services according the network.  
In the Organise Networks menu, there are two columns: the network  
list column and the service list column.  
The services are displayed in the service column according to the  
their networks.  
To delete the network, proceed as follows:  
1. Activate the Organise Networks menu via the Main menu.  
2. Move the cursor to the network list column.  
3. Select the network name using the  
4. Press the RED button to mark the selected network.  
5. Press the OK ( ) button to delete the marked networks.  
button.  
To move/change the order of the network in the network list,  
proceed as follows:  
1. Activate the Organise Networks menu via the Main menu.  
2. Move the cursor to the network list column.  
3. Select the network name using the  
4. Press the GREEN button. The  
the network name.  
button.  
icon is then displayed beside  
5. Move the network name to the desired position using the  
button.  
6. Press the OK (  
) or EXIT (  
) button to confirm.  
GB37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Delete Satellites  
The Delete Satellites menu supplies the following functions:  
• Delete a satellite. It will also delete all services belonging to the  
satellite.  
• Delete a transponder. It will also delete all services belonging to  
the transponder.  
• Sort the services according to the satellite and the transponder.  
In the Delete Satellite menu, there are three columns:  
‘SAT” (the satellite list column), “TP (MHz)” (the transponder list  
column) and “Services” (the service list column).  
To delete a satellite, proceed as follows:  
1. Activate the Delete Satellite menu via the Main menu.  
2. Move the cursor to the satellite list column using the  
button.  
3. Select the desired satellite name using the  
button.  
4. Press the RED button to mark the satellite name.  
5. If all the desired satellite names are marked, press the OK (  
button to delete all the marked satellite names.  
)
6. If all the satellites are to be deleted, mark the “ALL” item.  
To delete a satellite transponder, proceed as follows:  
1. Activate the Delete Satellite menu via the Main menu.  
2. Move the cursor to the transponder list column using the  
button.  
3. Select the desired transponder name using the  
button.  
4. Press the RED button to mark the transponder name.  
5. If all desired transponder names are marked, press the  
OK (  
) button to delete all marked transponders.  
GB38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-3. Service Searching  
Antenna Setting  
The Antenna Setting menu sets the characteristics of each antenna.  
32 antennae can be supported, one of which for SMATV.  
The Antenna Setting menu supplies the following items to  
characterise the antenna.  
Antenna Alternative  
Assigns an index to each antenna. Hence, the value is unique for  
each antenna. It can assign up to 32 indexes.  
Satellite Name  
Assigns a satellite name to each antenna. The available satellite  
names supplied by default can be used. Moreover, the satellite  
name can be defined by the user with the “User Defined” item.  
LNB Frequency  
Assigns LNB frequency of LNB in each antenna. It can be set  
as “Universal”, “5150”, “9750”, “10600”, “10750” and “11475”.  
It can also be set as any value using the numeric buttons.  
22KHz Tone  
Disables/enables the 22KHz tone in the signal line.  
DiSEqC Input  
It sets the DiSEqC input to select a proper antenna.  
It can be set as “Tone Burst A”, “Tone Burst B”, “DiSEqC A”,  
“DiSEqC B”, “DiSEqC C” and “DiSEqC D”.  
Motorised System  
Disables/enables the motorise function.  
LNB Power  
Switches/off the LNB power.  
LNB Voltage  
Sets the LNB voltage level. The LNB voltage may drop too low to  
supply power to the LNB due to the long length of the signal cable.  
To compensate the voltage drop, the item should be set on “High”.  
GB39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
Manual Search  
The function of the Manual Search menu is to search services in  
one transponder using information from a satellite transponder.  
(If the Network Search option is enabled, services in other  
transponders are searched).  
The following items are supplied as parameters:  
Antenna Alternative  
Specifies the antenna used for searching.  
Frequency  
Sets the frequency of a transponder.  
Polarisation  
Sets the polarisation type (horizontal or vertical).  
Symbol Rate  
Sets the symbol rate of a transponder.  
FEC(Forward Error Correction)  
Sets the FEC value of a transponder.  
Network Search  
Enables/disables the network search option. If the option is enabled,  
all services in other transponders may be searched according to  
information in the NIT.  
Automatic Skip  
Enables/disables the automatic skip option. If this option is enabled,  
the scrambled services are skipped during the search.  
BAT Search  
Some operators define the order of services in a list using BAT.  
If this option is enabled, the services will be ordered according to  
the BAT information.  
GB40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To manually search the services, proceed as follows:  
1. Activate the Manual Search menu via the Main menu.  
2. Set all the parameters according to transponder information.  
3. Use the progressive bars at the bottom of window to check  
whether or not the transponder is locked.  
4. Press the OK (  
) button to activate the search services.  
During the search, a sandglass rotates vertically.  
5. To cancel the search, press the EXIT (  
6. If the search has been carried out, the searched services are  
displayed.  
) button.  
7. Press the OK (  
) button to save the services,  
) button to discard all the services.  
otherwise, press the EXIT (  
GB41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Guide of Main Menu  
Automatic Search  
The function of the Automatic Search menu is to search services  
using information from a satellite.  
The following items are supplied as parameters.  
Antenna Alternative  
Specifies the satellite in which the automatic search will be  
performed.  
Automatic Skip  
Enables/disables the automatic skip option. If this option is enabled,  
the scrambled services are skipped during the search.  
Search Type  
Specifies search type. If the search type is “Detail”, then four symbol  
rates are added and used during the search.  
Symbol Rate table(optional)  
Upsets up to four symbol rates for searching when the search type  
is “Detail”.  
To automatically search the services, proceed as follows:  
1. Activate the Automatic Search menu.  
2. Set all the parameters according to the satellite information.  
3. Press the OK (  
4. Press the EXIT (  
) button to start the search.  
) button to cancel during the search.  
The Automatic Search may take a long time to search all the  
services, depending on the parameter settings.  
Since the Automatic Search is based on hard-coded information,  
this information is properly updated to search all services.  
To obtain the updated information, please consult the HUMAX web  
site.  
GB42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-4. Status  
The function of the Status menu is to supply users with information  
on several STB statuses, such as:  
• Information on the Software version,  
• Information on the Hardware version,  
• Information on the signal level of the current locked TP,  
• Information on OTA availability.  
This information is mainly intended for operators or installers.  
STB Status  
The STB status menu supplies information on the software and  
hardware versions.  
To receive the information, proceed as follows:  
1. Activate the Status Menu via the Main menu.  
2. Select the Status menu using the  
button,  
then press the OK (  
3. Press the EXIT (  
) button to enter the menu.  
) button to exit the menu.  
Signal Detection  
The Signal Detection menu supplies information on signal level and  
signal quality.  
This can be used when the antenna is adjusted to the desired  
satellite as the signal level and quality are maximally high when the  
antenna is pointed directly at the satellite.  
To receive the information, proceed as follows:  
1. Activate the Status Menu via the Main menu.  
2. Select the Signal Detection menu using the  
button,  
) button to enter the menu.  
) button to exit the menu.  
then press the OK (  
3.Press the EXIT (  
STB Upgrade  
The OTA can be performed via the STB Upgrade menu.  
If there is an available OTA image on the air, the menu may be  
selected. Otherwise, the menu is greyed out and cannot be  
selected.  
Loader Status  
The Loader Status menu supplies information on the loader status.  
GB43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Guide  
3-5. Conditional Access  
The Conditional Access menu supplies information on  
IRDETO embedded CAS.  
There are four sub-menus in the menu:  
• Version Information,  
• Smart Card Information,  
• Transport Stream Information,  
• Monitoring ECM/EMM.  
Version Information  
The Version Information menu supplies technical information on  
IRDETO embedded CAS.  
To retrieve the information, proceed as follows:  
1. Activate the Conditional Access menu via the Main menu.  
2. Select the Version Information menu using the  
button and  
) button to retrieve the information.  
) button to exit the menu.  
press the OK (  
3. Press the EXIT (  
Smart card Information  
The Smart card Information menu supplies information on  
the smart card in the slot, such as serial number and nationality.  
If there is no smart card or an invalid one in the slot, the menu  
cannot be entered.  
To retrieve the information, proceed as follows:  
1. Activate the Conditional Access menu via the Main menu.  
2. Select the Smart card Information menu and press the OK (  
button to retrieve the information.  
)
3. Press the EXIT (  
) button to exit the menu.  
Transport Stream Information  
The Transport stream Information supplies information on the  
current service such as EMM PID and the service status.  
To retrieve the information, proceed as follows:  
1. Activate the Conditional Access menu via the Main menu.  
2. Select the Transport stream Information using the  
button  
and press the OK (  
3. Press the EXIT (  
) button to retrieve the information.  
) button to exit the menu.  
GB44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Monitoring EMM/ECM  
The Monitoring EMM/ECM menu periodically supplies information  
on the ECM and EMM.  
To retrieve the information, proceed as follows:  
1. Activate the Conditional Access menu.  
2. Select the Monitoring EMM/ECM menu using the  
button and  
press the OK (  
3. Press the EXIT (  
) button to retrieve the information.  
) button to exit the menu.  
3-6. Mail Messages  
The Mail Messages menu shows the mail messages received over  
the air. The mail messages are intended for the operator, to inform  
users. If there is a new mail message available, the  
icon  
appears at the top right corner of the screen. There are four  
columns in the menu, such as the received date and time (DATE &  
TIME), view status (VIEW) and the type (TYPE).  
If the mail message has not yet been viewed, a ‘U’ is marked in the  
“VIEW” column. In the menu, the mail can be viewed or deleted  
from the mail list.  
The mark ‘M’ in the “TYPE” column means that the mail message  
received is a normal mail message.  
The mark ‘A’ in the “TYPE” column means that the received mail  
message is a message of announcement.  
To view or delete the mail message, proceed as follows:  
1. Activate the Mail Message menu via the Main menu.  
2. Select the desired mail message using the  
3. Press the GREEN button to view it.  
4. Press the YELLOW button to delete it.  
button.  
5. Press the EXIT (  
) or BLUE button to exit the menu.  
4. Utility  
The Utility menu supplies two functions: Calendar and Biorhythm.  
In “Calendar”, the current calendar is displayed on the screen.  
The desired month can be chosen using the  
button.  
In “Biorhythm”, if the date of birth is input, the specific biorhythm is  
displayed on the screen.  
GB45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motorised System  
DiSEqC 1.2 User Instructions  
If you have a DiSEqC 1.2 motorised system, you can use the available DiSEqC 1.2 functions.  
The following instruction describes how to use the DiSEqC 1.2 functions to store the positions of the  
satellites and search for the services (STAB Rotor Sat motor recommended).  
1. Satellite Setting Menu Options  
When the DiSEqC Motorised System is Enabled in the Antenna Setting, a new menu is available for  
configuring the motor. This menu is called “Satellite Setting” and is accessed by pressing the OK  
(
) button with the Alternative Antenna option highlighted in the Manual Search menu.  
The following options are available on the Satellite Setting menu:  
Satellite Name  
A selection of satellite names that can be used to identify a motor position. If the satellite name you  
require is not available, please use another one. In installer mode, the Satellite Name Reference  
refers to the 0 position of the motor.  
Movement  
In user mode, this is used to fine-tune the position of the motor for better reception.  
In Installer mode, this is used to manually search for the position of a satellite.  
Motor Control  
• Search: Searches for services on the chosen transponder.  
• Goto: Moves the motor to the stored position of the selected satellite name.  
• Store: Stores the current position of the motor for the selected satellite name.  
• Reset: Resets all stored positions of the motor relative to the 0 position (Installer mode only).  
DiSEqC Command Mode  
Changes the current mode between Installer and User.  
2. Setting your Receiver for DiSEqC 1.2  
You must set your receiver up so that it is ready to use DiSEqC 1.2. To do so, proceed as follows:  
1. Press the MENU (  
) button to display the Main menu.  
2. Select the Service Searching option and press the OK (  
button to display the Service Searching menu.  
3. Select the Antenna Setting option and press the OK (  
button to display the Antenna Setting menu.  
)
)
4. You must set up a separate alternative antenna for each  
satellite position required.  
5. Select the name of the satellite you wish to use.  
6. Select the correct LNB frequency for the LNB you are using.  
7. Set the Motorised System to Enable to use the  
buttons.  
8. The option DiSEqC Input Selection should now be disabled. This option is used for DiSEqC 1.0  
and cannot be used in conjunction with DiSEqC 1.2. Your receiver is now ready to use DiSEqC  
1.2. To return to the Main Menu, use the EXIT (  
) button until you reach the Main menu.  
GB46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Initial Satellite Position Search  
This is required when you first set your receiver up to use DiSEqC 1.2, and sets the positions of all  
pre-programmed satellites.  
1. Make sure your motor is installed correctly with the calibrations  
adjusted for the region in which you are located.  
(Please consult the user’s manual for your motor).  
2. Make sure your receiver is set up to use DiSEqC 1.2.  
(see Section 2 above).  
3. In the Main menu, select the Service Searching option and  
press the OK (  
) button. You should now see the Service  
Searching menu.  
4. Highlight the Alternative Antenna option and press the OK (  
)
button to display the Satellite Setting menu.  
5. Highlight the DiSEqC Command Mode option and use the  
buttons to change the value to  
buttons to change the value to reset, then  
) button to continue. All the pre-  
Installer, then press the OK (  
6. Highlight the Motor Control option and use the  
press the OK ( ) button.  
7. You will now see a warning message. Press the OK (  
) button.  
programmed satellite motor positions should now be correct. If you have any other DiSEqC 1.2  
motor brand or model, then you may need to store the satellite positions yourself. (Please refer to  
the user’s manual for your motor).  
8. Highlight the DiSEqC Command Mode option and use the  
User, then press the OK ( ) button.  
buttons to change the value to  
9. You should now be ready to start storing services for the various satellites (see 5 onwards).  
4. Motor Limit Setting  
Use this option to set the East and West limits of the motor. This should be used to prevent your dish  
from hitting anything that may obstruct the path of the dish.  
1. On the Main menu, select the Service Searching option and press the OK (  
) button.  
You should now see the Service Searching menu.  
2. Select the Manual Search option and press the OK (  
)
button. You should now see the Manual Search menu.  
3. Highlight the Alternative Antenna option and press the OK (  
button. You should now be in the Satellite Settings menu.  
4. Press the RED button to access the Motor Limit Setting menu.  
)
5. Highlight the Limit Setting option and use the  
buttons to  
disable this. (Warning: When this option is disabled, your motor  
will be able to move beyond any limits previously  
stored - please make sure there is nothing obstructing  
the path of your dish.)  
GB47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motorised System  
6. To set the East Limit:  
a) Select “Movement” and use the  
motor East or West until it is at the position you wish  
buttons to move your  
to use as your East Limit. Use the  
buttons to stop the  
motor at the correct position.  
b) Highlight the Store East Limit option and press the OK (  
button to store the current position as your East Limit.  
)
To set the West Limit:  
a) Select “Movement” and use the  
buttons to move your  
motor East or West until it is at the position you wish  
buttons to stop the motor at the correct position.  
to use as your West Limit. Use the  
b) Highlight the Store West Limit option and press the OK (  
as your West Limit.  
) button to store the current position  
5. Manual Satellite Search  
The purpose of this is to set the motor position manually for each satellite.  
This is useful if the satellite you require is not available in the pre-programmed list (see 3 above).  
To do this, you must access the Satellite Settings menu. Proceed as follows:  
1. Select “Service Searching” from the Main menu and press the OK (  
) button to display the  
Service Searching menu.  
2. Select the Manual Search option and press the OK (  
) button to display the Manual Search  
menu. Select the relevant Alternative Antenna you are using for this satellite.  
3. Enter the Frequency, Polarisation, Symbol Rate and FEC for a transponder on the satellite you  
wish to find. The transponder information should be unique to the satellite.  
4. Select the Alternative Antenna option and press the OK (  
Settings menu.  
) button to display the Satellite  
5. Highlight the DiSEqC Command Mode option and, using the  
buttons, change this to Installer.  
6. Highlight the Satellite name option and use the  
buttons to select the satellite you want to find.  
Use others if the name of the satellite you want does not appear.  
7. When you have selected the satellite you are looking for, go down to the Movement option, and  
again using the  
buttons, start the motor moving.  
8. You should move the motor as far west as possible and then move it east so that you cover the  
motor’s complete movement range.  
9. During the move from west to east, the Signal Quality bar should register a signal once.  
This is the satellite’s position. If there two or more different positions register a  
signal, then you must choose another frequency that will be unique to the satellite you want.  
10. Use the Signal level and Strength Quality bar at the bottom of the screen to judge the best  
position for the dish.  
11. Use the  
12. When you have found the best position for the dish, go to the Motor Control option, and using the  
buttons, select “Store” and press the OK ( ) button. The position of the satellite should  
now be stored.  
buttons to stop the motor when required.  
13. If you have not stored this position, it will be lost when you exit the menu.  
14. Repeat the process for each satellite if required, remembering to use a different alternative  
antenna for each satellite.  
GB48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Moving to a pre-set satellite  
Once you have stored the positions of the satellites you want (see below left) you can search for the  
services transmitted from them. Before doing this, you must move the motor to the position of the  
satellite you wish to search for. To do this, you must access the Satellite Settings menu. Proceed as  
follows:  
1. Select “Service Searching” from the Main menu and press the OK (  
) button to display the  
Service Searching menu.  
2. Select the Manual Search option and press the OK (  
menu.  
3. Select the Alternative Antenna option and press the OK (  
) button to display the Manual Search  
) button to display the Satellite  
Settings menu.  
4. In the Satellite Settings menu ensure that you have the DiSEqC Command Mode option set to  
“User”.  
5. Highlight the option Satellite Name and use the  
to view.  
buttons to select the satellite you want  
6. When you have selected the satellite you wish to view, go down to the Motor Control option and,  
using the buttons again, select “Go to” and press the OK ( ) button.  
7. The motor will now move to the selected satellite’s position.  
8. The Movement option is used to fine-tune the motor’s position.  
9. When using the Movement option for fine-tuning, you must remember to store the changes you  
have made, otherwise they will be lost.  
7. Searching for services on your selected Satellite  
Once you have moved the motor into position, you can search for the channels transmitted from the  
relevant satellite. To search for services on your new selected satellite, proceed as follows:  
1. Move the motor to the position of the satellite you wish to  
search for (see section 6 above):  
2. Select “Service Searching” from the Main menu and press the  
OK (  
) button to display the Service Searching menu.  
3. Select the manual search option and press the OK (  
) button  
to display the Manual Search menu.  
4. Now enter the Frequency and Symbol Rate using the NUMERIC  
buttons (0~9).  
Next, enter the Polarisation and FEC values using the  
buttons.  
5. When you have entered all these details, press the OK (  
)
button and the search will begin.  
6. When the search has finished, press the OK (  
) button to  
view.  
7. Repeat the process for all the transponders you want from this  
satellite.  
GB49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motorised System  
8. Automatic Search  
It is possible to use automatic search using the DiSEqC 1.2 motorised system.  
1. Ensure that the position for the satellite you want to search for is correct (see Section 3 and 5  
above).  
2. In the Main menu, select the channel searching option and press the OK (  
) button.  
3. In the Service Searching menu, select the Alternative Antenna that you 3set for this satellite.  
4. When you search new services, please refer to Automatic Search on page GB42.  
5. When the search has ended, press the OK (  
) button to store and view the services.  
Now that you have stored all the satellite positions and searched for all the services you want, you  
can use your receiver as normal. When you change to a service transmitted from a different  
satellite, you will have to wait a few seconds to allow the motor to move into position to receive the  
new service.  
GB50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
GB51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Map  
GB52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
Conditional Access Interface  
1 Slot Smart card  
Irdeto Embedded  
Tuner & Channel  
Input Connector  
Frequency Range  
Input Impedance  
Signal Level  
IF  
F-type, IEC 169-24, Female  
950 MHz to 2150 MHz  
75  
-25 to -65 dBm  
480 MHz  
IF Band width  
LNB Power &  
Polarisation  
36 MHz  
Vertical : +13.5 V  
Horizontal : +18 V  
Current : 500 mA Max. Overload Protection  
22 KHz Tone  
Frequency : 22 ± 4 KHz  
Version 1.0/1.2 Compatible  
QPSK  
Amplitude : 0.6 ± 0.2 V  
DiSEqC Control  
Demodulation  
Input Symbol Rate  
FEC Decode  
1-45 Ms/s  
Convolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8  
with Constraint Length K=7  
MPEG Transport Stream A/V Decoding  
Transport Stream  
MPEG-2 ISO/IEC 13818  
Transport stream specification  
MPEG-2 MP@ML  
Profile Level  
Input Rate  
15 Mbit/s Max  
Aspect Ratio  
Video Resolution  
Audio Decoding  
Audio Mode  
Sampling  
4:3, 16:9  
720 x 576  
MPEG/MusiCam Layer I & II  
Single channel/Dual channel/Joint stereo/Stereo  
32, 44,1 and 48 KHz  
Memory  
Main Processor  
Flash Memory  
TMIPS R3930 (81 MHz)  
3 Mbyte  
Graphic(MPEG) DRAM  
System DRAM  
4 Mbyte  
2 Mbyte  
Please note: The specification of the STB may be changed without advance notice.  
GB54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A/V & Data In/Out  
TV SCART  
Video Output (CVBS, RGB, S-Video)  
Audio Output  
(Resolution : 20 bits DAC, Max. 2 Vrms)  
Video Output (CVBS)  
Video Input (CVBS, RGB, S-Video)  
Audio Output (Resolution : 20 bits DAC, Max. 2 Vrms(fixed))  
RCA/Cinch Volume and Mute Control  
(Resolution : 20 bits DAC, Max. 2 Vrms)  
VCR SCART  
AUDIO R/L  
RS-232C  
Transfer rate 115,200 bps, 9pin D-sub Type  
Power Supply  
Input Voltage  
Type  
90 - 250V AC, 50/60 Hz  
SMPS  
Power Consumption  
Standby Power  
Protection  
Max. 30 W  
8 W  
Separate internal fuse. The input should be protected against  
lightning  
Physical Specifications  
Size (W x H x D)  
Weight (Net)  
260  
Around 1.3 kg  
x
50  
x
180 mm  
Operating Temp  
Storage Temp  
Storage Humidity  
0°C to + 45°C  
-10°C to + 70°C  
5% ~ 95% RH (Non-Condensing)  
You can use a special antenna switch with DiSEqC commands.  
When changing ASTRA1 to EUTELSAT, for example, a DiSEqC command is sent  
with the 22KHz tone via the antenna cable. The antenna switch will change  
ASTRA1 to EUTELSAT. The DiSEqC concept is a protective trademark of  
EUTELSAT.  
Data rate decides the picture quality of digital TV programmes.  
The data rate of about 5-6 Mbit/s coincides with the picture quality of an analogue  
TV programme.  
GB55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Air Conditioner 0010552537 User Manual
Hans Grohe Plumbing Product 28570001 User Manual
Harbor Freight Tools Bicycle 94142 User Manual
Havis Shields Automobile Accessories C 3190 User Manual
Honeywell Home Theater Server 301C User Manual
Honeywell Switch C437D User Manual
Hotpoint Cooktop N321IX User Manual
HTC PDAs Smartphones IMAP4 User Manual
Husqvarna Blower 225 HBV User Manual
IBM Computer Drive 22P6960 User Manual