Hotpoint Cooktop CEO 647 Z User Manual

Operating Instructions

HOB

Contents

Installation, 2-3

Positioning

Electrical connection

Description of the appliance, 4

Control panel

English,1

Start-up and use, 5-8

Switching on the hob

Switching on the cooking zones

Booster function

Switching off the cooking zones

Programming the cooking duration

Timer

Control panel lock

Switching off the hob

“Demo” mode

CEO 647 Z

Practical advice on using the appliance

Safety devices

Practical cooking advice

Precautions and tips, 9

General safety

Disposal

Care and maintenance, 10

Switching the appliance off

Cleaning the appliance

Disassembling the hob

Technical description of the models, 11

After Sales Service, 14

Guarantee, 15

Key Contacts, 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 220-240V 3 ~ 50 Hz

• 400V 3 - N ~ 50 Hz

0ixing

The appliance must be installed on a perfectly level

supporting surface.

Any deformities caused by improper fixing could affect

the features and operation of the hob.

• 400V - 2+2N ~ 50 Hz

The thickness of the supporting surface should be

taken into account when choosing the length of the

screws for the fixing hooks:

Separate the wires and connect them in accordance

with the instructions given in the following table and

diagrams:

• 30 mm thick: 23 mm screws

• 40 mm thick: 13 mm screws

Voltage and

Electrical cable

Wire connection

mains frequency

400V - 2+N ~

50 Hz

: yellow/green;

N: the two blue wires together

L1: black

8ix the hob as follows:

1. Use short flat-bottomed screws to fix the 4

alignment springs in the holes provided at the central

point of each side of the hob.

220-240V 3 ~

50Hz

L2: brown

400V 3-N~ 50Hz

: yellow/green;

N1: blue

2. Place the hob in the cavity, make sure it is in a

central position and push down on the whole perimeter

until the hob is stuck to the supporting surface.

3. 8or hobs with raised sides: After inserting the hob

into its cavity, insert the 4 fixing hooks (each has its

own pin) into the lower edges of the hob, using the

long pointed screws to fix them in place, until the

glass is stuck to the supporting surface.

400V - 2+2N ~

50 Hz

N2: blue

L1: black

L2: brown

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be installed

with a minimum opening of 3 mm between contacts.

! The installer must ensure that the correct electrical

connection has been made and that it is fully

compliant with safety regulations.

! The screws for the alignment springs must remain

accessible.

! In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant

with the law.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate

located on the appliance itself.

• The voltage falls within the range of values indicated

on the data plate.

Electrical connection

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The electrical connection for the hob and for any built-

in oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with the

instructions given in the following table and diagrams:

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only.

Voltage and

mains frequency

! The manufacturer declines any liability should

these safety measures not be observed.

! Do not remove or replace the power supply cable for

any reason. Its removal or replacement will void the

warranty and the CE marking. INDESIT does not

assume liability for accidents or damage arising from

replacement/removal of the original power supply

cable. Replacement can only be accepted when

carried out by personnel authorised by INDESIT and

using an original spare part.

Electrical cable

Wire connection

: yellow/green;

N: the two blue wires

together

L: brown and black

together

220-240V 1+N ~

50 Hz

Other types of connection

If the mains supply corresponds with one of the

following:

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the

appliance

Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panel

on your appliance.

BOOSTER

indicator light

BOOSTER

button

Booster

• COOKING ZONE PROGRAMMED indicator lights

show which cooking zones are being used during

a cooking programme (see Start-up and use).

• INCREASE TIME button increases the time value

set on the timer (see Start-up and use).

• DECREASE TIME button decreases the time

value set on the timer (see Start-up and use).

• CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (see Start-

up and use).

• COOKING ZONE SELECTOR button shows a

particular cooking zone has been selected and

therefore various adjustments are possible.

• CONTROL PANEL LOCK indicator light shows

the control panel has been locked (see Start-up

and use).

• COOKING ZONE SELECTOR button is used to

select the desired cooking zone.

• COOKING ZONE POWER SELECTOR buttons

switch on the hotplate and control the power (see

Start-up and use).

• POWER indicator provides a visual display for the

current heat level.

• TIMER indicator light shows that the timer has

been activated

• ON/O00 button switches the appliance on and off.

• ON/O00 indicator light shows whether the

appliance is on or off.

• BOOSTER button activates the booster function -

3000 W - of the cooking zone (see Start-up and

use).

• PROGRAMME TIMER button controls the cooking

programme times (see Start-up and use).

• BOOSTER indicator light shows that the booster

function has been activated.

• PROGRAMME TIMER display shows which

programme has been selected (see Start-up and

use).

Download from Www.Somanuals.com. All Manuals Search And Download.

Start-up and use

! The glue applied on the gaskets leaves traces of

grease on the glass. Before using the appliance, we

recommend you remove these with a special non-

abrasive cleaning product. During the first few hours of

use there may be a smell of rubber which will

disappear very quickly.

Switching on the hob

To switch the hob on, press and hold the

for approximately one second.

button

Switching on the cooking zones

! A few seconds after the hob is connected to the

electricity supply, a buzzer will sound. The hob may

now be switched on.

Each cooking zone is controlled using a selector

button and a power adjustment device consisting

of power level selector buttons between the values of 0

and 9.

Types of noise during normal hob operation:

• Buzz: due to the vibration of the metallic parts that

make up the induction element and the pot; it is

generated by the electromagnetic field required for

heating and increases as the power of the induction

element increases.

• To begin operating a cooking zone, press the

corresponding control button and set the desired

power level using the power level selector buttons

between 0 and 9.

• Soft whistle: heard when the pot placed on the

heating zone is empty; the noise disappears once

food or water is placed into the pot.

Switching off the cooking zones

To switch off a cooking zone, select it using the

• Crackle: produced by the vibration of materials on

the bottom of the pot due to the flow of parasitic

currents caused by electromagnetic fields

corresponding selector button

and:

• Press power level selector button 0: this

immediately returns the power setting to 0 and the

cooking zone switches off.

(induction); can be more or less intense depending

on the material making up the bottom of the pot,

and decreases as the pot dimensions increase.

• Loud whistle: heard when two induction elements

of the same group function simultaneously at

maximum power and/or when the booster function is

set on the larger element while the other is auto-

adjusted. Noise is reduced by decreasing the power

level of the auto-adjusted induction element; pot

bottom layers made of different kinds of materials

are among the main causes of this noise.

Booster function

The booster function for some of the cooking zones

may be used to shorten heating-up times. It may be

Booster

activated by pressing the

button. The indicator

light directly above the button will illuminate. This

function boosts the power to 2000 W or 3000 W,

depending on the size of the relevant cooking zone.

The booster stops automatically after 4 minutes. While

the booster for one of the cooking zones is active, the

corresponding front or rear cooking zone will operate at

a reduced power level (e.g. if the booster for the rear

left-hand hotplate has been activated, the power level

of the front left-hand hotplate will be reduced). ,or

further information, please refer to the Technical

description of the models.

• ꢀan noise: a fan is necessary to ensure the hob

functions correctly and to safeguard the electronic

unit from possible overheating. The fan functions at

maximum power when the large induction element is

at maximum power or when the booster function is

on; in all other cases, it works at average power

depending on the temperature detected.

,urthermore, the fan may continue to work even after

switching the hob off, if the temperature detected is

high.

Programming the cooking duration

The types of noise listed above are due to induction

technology and are not necessarily operational faults.

! All the cooking zones may be programmed

simultaneously, for a duration between 1 and 99

minutes.

! If the

button is pressed for an extended

period of time, the display scrolls quickly though the

power levels and timer minutes.

1. Select the cooking zone using the corresponding

selector button.

2. Adjust the temperature.

3. Press the

programming button.

Download from Www.Somanuals.com. All Manuals Search And Download.

the time has elapsed, a buzzer will sound (for one

minute).

4. Set the cooking duration using the

and

buttons.

Control panel lock

5. Confirm by pressing the

button.

The timer begins counting down immediately. A

buzzer sounds for approximately 1 minute and the

cooking zone switches off when the set programme

has finished.

When the hob is switched on, it is possible to lock the

oven controls in order to avoid accidental changes

being made to the settings (by children, during

cleaning, etc.). Press the

button to lock the

Repeat the above procedure for each hotplate you

wish to programme.

control panel: the indicator light above the button will

switch on.

To use any of the controls (e.g. to stop cooking), you

Using multiple programmes and the display

must switch off this function. Press the

button for

If one or more hotplates are programmed, the display

will show the data for the hotplate with the least time

remaining, and the light corresponding to the position

of the hotplate will flash. The lights corresponding to

the other hotplates programmed will be switched on.

To display the time remaining for the other

a few moments, the indicator light will switch off and

the lock function will be removed.

Switching off the hob

Press the

button to switch the appliance off.

programmed hotplates, press the

button

If the control panel lock has been activated, the

controls will continue to be locked even after the hob is

switched on again. In order to switch the hob on again,

you must first remove the lock function.

repeatedly. The times remaining for each hotplate will

be shown in a clockwise order, beginning with the front

left hotplate.

Changing the programme

“Demo” mode

1. Press the

button repeatedly until the duration

It is possible to set the hob to a demonstration mode

where all the controls work normally but the heating

elements do not switch on. To activate the “demo”

mode the hob must be switched on, with all the

hotplates switched off.

you wish to change is shown.

2. Use the

buttons to set the new duration.

3. Confirm by pressing the

button.

• Press and hold the

and

buttons

To cancel a programme, follow the above instructions.

At step 2, press the button: the duration decreases

simultaneously for 6 seconds. When the 6 seconds

have elapsed, the ON/O,, and CONTROLS

LOCKED indicator lights will flash for one second.

progressively until it reaches 0 and switches off. The

programme resets and the display exits programming

mode.

Release the

button;

and

buttons and press the

• The display will show the text DE and MO and the

hob will be switched off.

Timer

• When the hob is switched on again it will be set to

the “demo” mode.

The hob must be switched on.

The timer can be used to set a duration up to 99

minutes.

To exit this mode, follow the procedure described

above. The display will show the text DE and O, and

the hob will be switched off. When it is next switched

on, the hob will function normally.

1. Press the

programming button until the timer

indicator light is illuminated.

2. Set the desired duration using the

and

Practical advice on using the appliance

buttons.

3. Confirm by pressing the

button.

! Use cookware made from materials which are

The timer begins counting down immediately. When

compatible with the induction principle (ferromagnetic

Download from Www.Somanuals.com. All Manuals Search And Download.

chocolate. As the cooking zone cools, the power

display will show . The display switches off when

material). We especially recommend pans made from:

cast iron, coated steel or special stainless steel

adapted for induction. Use a magnet to test the

compatibility of the cookware.

the cooking zone has cooled sufficiently.

Overheating protection

SUITABLE

UNSUITABLE

If the electronic elements overheat, the hob switches

off automatically and

ꢀ

appears on the display,

followed by a flashing number. When the temperature

has reached a suitable level, this message disappears

and the hob may be used again.

Copper,

Cast iron

Enamelled steel

Special stainless steel

Aluminium, Glass, Earthenware,

Ceramic, non magnetic Stainless steel

Safety switch

In addition, to obtain the best results from your hob:

• Use pans with a thick, flat base in order to fully

utilise the cooking zone.

The appliance has a safety switch which automatically

switches the cooking zones off after they have been in

operation for a certain amount of time at a particular

power level. When the safety switch has been

triggered, the display shows “0”.

,or example: the right rear hotplate is set to 5 and will

switch off after 5 hours of continuous operation, while

the front left hotplate is set to 2 and will switch off after

8 hours.

• Always use pans with a diameter which is large

enough to cover the hotplate fully, in order to use all

the available heat.

Maximum operating

Power level

time in hours

• Make sure that the base of the cookware is always

clean and dry, in order to fully utilise and extend the

life of both the cooking zones and the cookware.

• Avoid using the same cookware which has been

used on gas burners: the heat concentration on gas

burners may distort the base of the pan, causing it

not to adhere correctly.

Safety devices

Pan sensor

Buzzer

Each cooking zone is equipped with a pan sensor

device. The hotplate only emits heat when a pan with

suitable measurements for the cooking zone is placed

on it. If the indicator light is flashing, it may indicate:

• An incompatible pan

This can also indicate several irregularities:

• An object (a pan, cutlery, etc.) has been placed on

the control panel for more than 10 seconds.

• Something has been spilt on the control panel.

• A button has been pressed for too long. All of the

above situations may cause the buzzer to sound.

Remove the cause of the malfunction to stop the

buzzer. If the cause of the problem is not removed,

the buzzer will keep sounding and the hob will

switch off.

• A pan whose diameter is too small

• The pan has been removed from the hotplate.

Residual heat indicators

Each cooking zone is equipped with a residual heat

indicator. This indicator signals which cooking zones

are still at a high temperature. If the power display

shows

, the cooking zone is still hot. It is possible,

for example, to keep a dish warm or melt butter or

Download from Www.Somanuals.com. All Manuals Search And Download.

Practical cooking advice

Pressure cooking

Pressure cooker

Frying

Boiling

•

Grilling

•

Crêpes

Cooking on a high flame and browning

(roasts, steaks, escalopes, fish fillets,

fried eggs)

Fast thickening (liquid juices)

Boiling water (pasta, rice, vegetables)

Milk

Slow thickening (dense juices)

Bain-marie cooking

Pressure cooking after whistle

™

-{}-

Low-flame cooking

(stews)

Reheating dishes

™

Chocolate sauce

Keeping food hot

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

! This appliance has been designed and manufactured in

the centre of the hob in order to avoid accidental

burns.

compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

This appliance conforms to the following European

Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low Voltage) and

subsequent amendments;

• The appliance should not be operated by people

(including children) with reduced physical, sensory or

mental capacities, by inexperienced individuals or by

anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by

someone who assumes responsibility for their safety or

receive preliminary instructions relating to the operation

of the appliance.

-89/336/EEC dated 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent amendments.

General safety

! Make sure that the air inlet behind the fan grille is never

obstructed. The built-in hob should, in fact, be provided

with suitable ventilation for the cooling of the electronic

components used in the appliance.

• ꢀor the attention of wearers of pacemakers or

other active implants:

The hob complies with all current standards on

electromagnetic interference.

! We advise against the installation of an induction hob

above an under-the-counter refrigerator (heat) or above a

washing machine (vibrations). In fact, there would be

insufficient space for the ventilation of electronic

components.

Your induction hob is therefore perfectly in keeping with

legal requirements (89/336/CEE directives). It is

designed not to create interference on any other

electrical apparatus being used on condition that the

apparatus in question also complies with this

legislation.

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial

use.

Your induction hob generates short-range magnetic

fields.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

To avoid any interference between your induction hob

and a pacemaker, the latter must be designed to

comply with relevant regulations.

• Do not touch the appliance when barefoot or with wet

or damp hands and feet.

In this respect, we can only guarantee our own product

conformity. Please consult the pacemaker manufacturer

or your doctor concerning its conformity or any possible

incompatibility.

• The appliance must be used by adults only for the

preparation of food, in accordance with the instructions

provided in this booklet. Do not use the hob as a

worktop or chopping board.

• Do not let children play with the appliance.

• The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with a

sharp object such as a tool. If this happens,

disconnect the appliance from the electricity mains

immediately and contact a Service Centre.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-

out dustbin is marked on all products to remind the

owner of their obligations regarding separated waste

collection.

• Ensure that power supply cables of other electrical

appliances do not come into contact with the hot parts

of the hob.

• Remember that the cooking zones remain relatively hot

for at least thirty minutes after they have been switched

off. An indicator light provides a warning when residual

heat is present (see Start-up and use).

• Keep any object which could melt away from the hob,

for example plastic and aluminium objects, or products

with a high sugar content. Be especially careful when

using plastic film and aluminium foil or packaging: if

placed on surfaces which are still hot, they may cause

serious damage to the hob.

,or further information relating to the correct disposal of

exhausted household appliances, owners may contact

the public service provided or their local dealer.

• Always make sure that pan handles are turned towards

Download from Www.Somanuals.com. All Manuals Search And Download.

Careandmaintenance

Switching the appliance off

Stainless steel frame (only in models with outer

frame)

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Stainless steel can be marked by hard water which

has been left on the surface for a long time, or by

cleaning products containing phosphorus.

Cleaning the appliance

After cleaning, it is advisable to rinse the surface

well and dry it thoroughly. If water is spilt on the

surface, dry it quickly and thoroughly.

! Do not use abrasive or corrosive detergents (for

example, products in spray cans for cleaning

barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with

abrasive surfaces: these may scratch the surface

beyond repair.

! Some hobs have an aluminium frame which is

similar to stainless steel. Do not use any cleaning or

degreasing products which are not suitable for use

with aluminium.

! Never use steam cleaners or pressure cleaners on

the appliance.

Disassembling the hob

• It is usually sufficient simply to wash the hob

using a damp sponge and dry it with absorbent

kitchen towel.

If it is necessary to disassemble the hob:

1. Loosen the screws fixing the alignment springs on

each side.

2. Loosen the screws holding the fixing hooks in

each corner.

3. Take the hob out of its installation cavity.

• If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well

and dry thoroughly.

! Do not attempt to repair the appliance yourself. If

the appliance breaks down, contact a Service

Centre.

• To remove more stubborn dirt, use a suitable

scraper. Remove spills as soon as possible,

without waiting for the appliance to cool, to avoid

residues forming crusty deposits. You can

achieve excellent results by using a rust-proof

steel wire sponge - specifically designed for

glass ceramic surfaces - soaked in soapy water.

• If any plastic or sugary substances are

accidentally melted on the hob, remove them

immediately with the scraper, while the surface is

still hot.

• Once it is clean, the hob may be treated with a

special protective maintenance product: the

invisible film left by this product protects the

surface from drips during cooking. This

maintenance task should be carried out while the

appliance is warm (not hot) or cold.

• Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical description of

the models

The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking

zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic

bases.

Hobs

CEO 647 Z

Cooking zone

Back Left

Back Right

Front Left

Power (W)

Diameter (mm)

180

H 1800

I 1400 – 600 se Ant. Dx*

H 1400

145

Front Right

Total power

I 1400 – B 2000* – 600 se Post. Dx*

6800

Key:

I = single induction cooking zone

H = single hilight

B = booster: the power level of the cooking zone may be boosted to 3000 W

* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see

Start-up and use).

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

"No company is better positioned to offer an after sales service on a

Hotpoint appliance than us - the manufacturer"

As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and

labour guarantee for the first 12 months. In addition to this you also have the advantage of free

replacement parts for the first 5 years when fitted by a Hotpoint

engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service

options:

Repair Service and Information Help Desk

UK: 08709 066066

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the Model number and the Serial number of your appliance

Available 364 days a year with a fast, effective and value for money service. We have the largest white goods

repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour

guarantee for 12 months from the date of the repair.

If you require any information or have any questions about your appliance, our operators are on hand with help

and advice.

All this ensures that you will receive the best available after sales service possible.

Extended Warranties

UK: 08709 088 088

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover plans

to give you total peace of mind.

● Repair Protection Plan -

● Kitchen Cover

,REE service repairs for a single Hotpoint appliance during the period

of cover.

,REE service repairs for all your Hotpoint appliances less than 8

years old.

Genuine Parts and AccessoriesUK: 08709 077 077

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

A wide range of genuine parts and accessories are available from our hotline or through our web site.

Genuine parts and accessories, extended warranties and service repairs are all

available on our web-site at:

www.theservicecentre.co.uk

Download from Www.Somanuals.com. All Manuals Search And Download.

Guarantee

"Satisfaction guaranteed or your money back"

We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have

purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair

service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for

an engineer to call. If the technical problem is not resolved under this guarantee, we will replace

your machine or, if you prefer, give you your money back.

All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free

replacement parts for the first 5 years (except microwaves, selected integrated appliances and

cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.

Guarantee terms and conditions

Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the

following provisions that your appliance:

●

Has been installed and used correctly in accordance with this instruction booklet.

Has been used solely for domestic purposes and is located on domestic premises (ie. not for

commercial or trade use).

●

Has been properly connected to a suitable electrical supply voltage as stated on the appliance

rating plate.

Has not been subject to misuse, accident, modified or repaired by anyone other than one of our

own service engineers.

*or pre purchase information on any other Hotpoint product call: 08701 50 60 70

or visit: www.hotpoint.co.uk

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to

use quality recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the

appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged

into a mains socket, and the door cannot be locked shut.

Download from Www.Somanuals.com. All Manuals Search And Download.

04/2008 - 195069883.00

XEROX BUSINESS SERVICES

Key Contacts

After Sales Service

Over 1200 trained specialists, directly employed by us, ensure that you can have complete

confidence in both the appliances and services we offer.

Repair Service and Information Desk

UK: 08709 066 066

(Open 8 to 8 Mon - *ri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the following information:

Model number:

Serial number:

Extended Warranties

UK: 08709 088 088

(Open 8 to 8 Mon - Sun)

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Genuine Parts and Accessories

UK: 08709 077 077

(Open 8-30 to 5-30 Mon - *ri & 9 to 12 Sat)

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Car Seat PD203828A User Manual
HANNspree Flat Panel Television HANNSzzebra User Manual
Healthrider Treadmill 831297830 User Manual
Hotpoint Cooktop 6512 User Manual
Hotpoint Microwave Oven SBS51XS User Manual
HP Hewlett Packard Personal Computer 575611 001 User Manual
HP Hewlett Packard Printer 1200c User Manual
HP Hewlett Packard Switch SAS BL User Manual
Hsu Research Speaker VTF 2 User Manual
IBM Laptop 510Cs User Manual