Solid Core and Split Core Adjustable
Current “Status” Switches
CSS-O, CSS-C; CSP-O, CSP-C
INSTALLATION INSTRUCTIONS
The current switch may be mounted in any position using
the (2) #8 x 3/4 in. (19 mm) Tek screws and the mounting
holes in the base or snapped directly on to the 1-3/8 in.
(35 mm) DIN rail (See Figures 1 and 2). Leave a
SAFETY
WARNING
minimum distance of 1 in. (25 mm) between the current
switch and any other magnetic devices, such as
contactors and transformers.
For CSS-O,C ensure that all power sources
are disconnected and locked out before
installation as severe injury or death may
result from electrical shock due to contact
with high voltage wires.
For applications in which the normal operating current is
below the 0.8/2.0 Amps trip point (See Fig. 3), the
conductor being monitored may be looped through the
sensor 6/12 times giving you a total operating current of
6/12 times the original current.
CAUTION
This product is not intended to be used for life
or safety applications.
Example:
A small fan operating at 0.2 Amps can be wrapped
through the sensor 6 times to give you a total
operating current of 1.2 Amps flowing through the
CSS-O-A300-001. Another option is to use CSS-O-
A200-001.
A small fan operating at 0.2 Amps can be wrapped
through the sensor 16 times to give you a total
operating current of 3.2 Amps flowing through the
CSP-O-A300-001. Another option is to use the
CSP-O-A200-001.
CAUTION
This product is not intended for use in any
hazardous or classified locations.
INSTALLATION
Make sure that all installations are in compliance with all
national and local electrical codes. Only qualified
individuals that are familiar with codes, standards and
proper safety procedures for high voltage installations
should attempt installation. The current switches will not
require external power, since the power for the current
switch is induced from the conductor being monitored.
3X
WARNING
Never rely on the LEDs to determine whether
power is present at the current switch. The
red LED will indicate whether the current is
above the adjustable trip point. The green
LED will indicate whether the current is below
the adjustable trip point.
S
U
L
R
U
C
IMPORTANT
The current switch should be used on insulated
conductors only!
M25289
Fig. 1. Sensor placed on DIN rail
IND.CONT.EQ.
62-0242—01
3JHX
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLID CORE AND SPLIT CORE ADJUSTABLE CURRENT “STATUS” SWITCHES
Wiring
Honeywell recommends the use of a 2 conductor 16 to
2
22 AWG (1.3 to 0.3 mm ) shielded cable or twisted wire,
copper wire only, for all current switch output applications.
A maximum wire length of less than 98.4 feet (30 meters)
should be used between the current switches and the
Building Management System or controller.
NOTE: When using a shielded cable, be sure to connect
only (1) end of the shield to ground at the con-
troller. Connecting both ends of the shield to the
ground may cause a ground loop.
U S
L
R
U
C
When removing the shield from the sensor end, make
sure to properly trim the shield so as to prevent any
chance of shorting. The current switch output terminals
M25299
represent a solid-state switch for controlling AC and DC
loads and is not polarity sensitive. The recommended
Fig. 6. Opening with a screwdriver
torque to be used on the terminal block connections is
5.93 in-lbs. (0.67 Nm). The aperture (hole) size of the
current switch is 3/4 in. (19 mm) and will accept a
maximum cable diameter of 350 MCM (17.3 mm). See
Fig. 7 for use as a digital input to a building management
system and Fig. 8 for use as a pilot relay application.
OPERATING SPECIFICATIONS
Max Sensing Current Voltage: 600 Vac
Table 1. Specifications by Product Number.
Core Normal
Product Number Type Position
Adjustable OutputSwitch Max. Current Max. Current Max.Current
Trip Point
Rating
Cont.
for 6 secs.
for 1 sec.
CSS-O-A300-001 Solid N.O.
CSS-O-A200-001 Solid N.O.
CSS-C-A300-001 Solid N.C.
1.0-250 Amps 0.30 Amps @ 250 Amps
200 Vac/Vdc
500 Amps
1,000 Amps
0.50-250 Amps 0.30 Amps @ 250 Amps
200 Vac/Vdc
500 Amps
500 Amps
400 Amps
400 Amps
500 Amps
500 Amps
1,000 Amps
1,000 Amps
800 Amps
1.0-250 Amps 0.15 Amps @ 250 Amps
300 Vac/Vdc
CSP-O-A300-001 Split
CSP-O-A200-001 Split
CSP-C-A300-001 Split
CSP-C-A200-001 Split
N.O.
N.O.
N.C.
N.C.
3.0-200 Amps 0.30 Amps @ 200 Amps
200 Vac/Vdc
2.0-200 Amps 0.30 Amps @ 200 Amps
200 Vac/Vdc
800 Amps
3.0-250 Amps 0.15 Amps @ 250 Amps
300 Vac/Vdc
1,000 Amps
1,000 Amps
2.5-250 Amps 0.15 Amps @ 250 Amps
300 Vac/Vdc
DDC CONTROLLER
DI
(STATUS)
DIGITAL INPUT #1
DO
(RELAY COIL OR
CONTACTOR)
BUILDING MANAGEMENT
SYSTEM
RELAY
CONDITIONER
M25302
TRANSFORMER
24 VAC COIL
Fig. 7. Digital circuit
24 VAC COIL
M23933
120 VAC
LINE
Fig. 8. Analog circuit
3
62-0242—01
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLID CORE AND SPLIT CORE ADJUSTABLE CURRENT “STATUS” SWITCHES
Calibration of Adjustable Trip Point
Normal loads
The adjustable current switch has an operating range of
0-200 Amps or 0-250 Amps. Do not exceed! The
adjustable current switch comes with its fifteen-turn
With power on and the adjustable current switch on the
proper range, turn the fifteen-turn adjustment
potentiometer clockwise
until the red LED turns on
adjustable potentiometer set counter-clockwise
its maximum position. The adjustable current switch can
monitor Under load, Normal load and Overload
conditions, depending on how it's set. The procedure
below is for Normal load condition for part numbers
CSS-O-A300-001 and CSS-O-A200-001.
to
and stop immediately. The adjustment switch is now
tripped. The adjustable current switch Hysteresis (Dead
Band) is 10% of the trip point typically.
TROUBLESHOOTING
Problem
Solution
Red LED is on but the
Disconnect the wires from the current switch output. Measure the resistance across the
current switch didn’t activate. contacts with an Ohmmeter. See Table 2 below for resistance readings for a good unit.
Red LED didn’t turn on and Verify that the conductor you are monitoring is above the adjustable trip point. If the
the current switch didn’t
activate
sensor is monitoring less than the adjustable trip point, looping the wire may be
required. See Fig. 3.
Sensor doesn’t switch at all, Adjustment potentiometer is probably set to its maximum or minimum position. Turn the
regardless of current level.
potentiometer clockwise all the way and verify if the LED switches from red to green.
Table 2. Resistance Readings For Good Unit.
Product Number
Resistance if switch is open
Greater than 1 Meg ohms
Greater than 1 Meg ohms
Resistance if switch is closed
Approximately 2 ohms
CSS-O-A300-001
CSS-O-A200-001
CSS-C-A300-001
CSP-O-A300-001
CSP-O-A200-001
CSP-C-A300-001
CSP-C-A200-001
Approximately 2 ohms
Approximately 12 ohms
Approximately 2 ohms
Approximately 2 ohms
Approximately 12 ohms
Approximately 12 ohms
Greater than 1 Meg ohms
Greater than 1 Meg ohms
Greater than 1 Meg ohms
Greater than 1 Meg ohms
Greater than 1 Meg ohms
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Toronto, Ontario M1V 4Z9
® U.S. Registered Trademark
© 2007 Honeywell International Inc.
62-0242—01 C.H. Rev. 06-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|