OPERATION MANUAL
Built-in x35 ZOOM / WDR
High Resolution AUTO FOCUS CAMERA
HZC-855NX/PX Series
READ AND KEEP THIS OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION FOR SAFE OPERATION
1. Water and Moisture
8. When operation is incorrect or a malfunction is observed
To prevent fire or shock hazard, do not expose this camera
to rain or moisture.
While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.
2. Servicing
Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.
9. Cleaning
Turn the power off and wipe off the dirt with a dry soft cloth.
If it is extremely dirty, use furniture cleaner to wipe it off.
To clean the lens, use a blower or lens cleaning tissue.
(available from any camera dealer)
3. Power Sources
To prevent electric shocks and risk of hazards, do not use
more than the specified power source.
10. Do not shoot any source of bright light.
If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid
- state pickups, and is not a malfunction.
4. Environment
Do not install too warm or too cold place. Recommended
operation temperature is between -5℃ and 60℃
11. Damage Requiring service
Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:
5. Sunlight
Do not point the camera at the sun. CCD can be damaged.
a. If the power-supply cord or plug is damaged.
b. If the camera has been exposed to rain or water.
6. Heavy Shock and Vibration
Do not drop the camera or subject it to heavy shock of
vibration.
c. If liquid has been spilled, or objects have fallen into the camera.
d. If the camera does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the camera to its normal operation.
e. If the camera has been dropped or the cabinet has been damaged.
f . If the camera exhibits a distinct change in performance.
7. Install on an Unstable Place
Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance.
Warranty is not covered in case of natural disaster or wrong
Installation.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1. Features --------------------------------------------------------------- 5
2. Terms & Functions ------------------------------------------------ 6
3. Installation ------------------------------------------------------------ 7
4. Camera Control Methods ------------------------------------------- 8
5. On Screen Display -------------------------------------------------- 10
6. Specifications --------------------------------------------------------- 21
7. Dimensions ------------------------------------------------------------ 22
Thank you for using our Auto Focus Zoom Color Camera. To get the best
efficiency, read carefully all instructions in this manual before use, and
keep this manual for reference. If you have any problems with this camera,
contact your supplier to service.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Features
Ideal Digital Video Camera for Security
Privacy Zone Masking
The HZC-855NX/PX Ser. is a compact camera that offers easy system
integration. Coming with the built-in zoom lens, the user can monitor the
scene from variable angle without the extra lens.
HZC-855NX/PX Ser. mask the unwanted view for privacy protection
up to 8 zones. Privacy Zone operate with zoom in/out and it increases
the effect of privacy protection.
With the DSP technology, such intelligent controls as auto iris,
and auto white balance are possible to realize clear detailed picture.
Additionally, through RS-232C, RS422, remote Focus/Zoom operations
are also possible, along with manual control. All these features including
highly sensitive 1/4-inch CCD make the ideal digital processing CCTV
camera HZC-855NX/PX series more effective surveillance.
Remote Control through RS232C, RS422 Interface
Remote control operations are possible through RS232C/RS422
interface for Focus, Zoom control and various functions.
AI / Fuzzy Control Circuit with DSP
Advanced DSP technology automatically adjusts operations such as
Built -in x35 Optical power zoom lens
The HZC-855NX/PX Ser. with highly durable built-in zoom lens offers
auto focus, auto iris , and optical zoom functions enabling the user
to monitor a scene with clarity in any desired angle of view.
With the x35 optical zoom lens, the total zoom can be up to x90 with
x2.5 digital zoom processing.
Iris , White Balance flexibly adapting to environmental conditions.
Auto Iris : the iris is adjusted so that visual output is kept at a fixed
level, even if brightness of the surrounding changes.
Auto White Balance : color adjustment according to the color
temperature of the light source illuminating the subject.
white balance can be obtained even with fluorescent
lights, halogen lamps or outdoor.
High Resolution & Sensitivity SONY CCD
The chassis features a highly sensitive 1/4-inch CCD pickup with
approximately 380,000 effective pixels minimizing residual image
and geometric distortion. All images are reproduced with a high
horizontal resolution of 530 TV lines for fine detail.
WDR (Wide Dynamic Range)
This is the technology using dual shutters from both dark and bright
areas to be enhanced and displayed vivid video image. While a
conventional image shows white clip caused by the bright spot, WDR
overcomes and solves the obstacle of the white clip problem.
High Sensitivity with Integration and removal of IR filter
HZC-855NX/PX Ser. has the increased light sensitivity to 0.0005lx
(510 fields, IR Cut Filter ON) through field (frame) integration
technology. With Integration and removal of IR cut filter make more
effective surveillance though low light condition.(HZC-855NX/PX : less
than 0.00001 lx)
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Terms & Functions
FAR(-) BUTTON
VIDEO OUTPUT
This is the output terminal
for composite video signal .
TELE(UP) BUTTON
NEAR(+) BUTTON
VIDEO
S-VIDEO OUTPUT
SVIDEO
This is the output terminal
for separate Y/C signal .
MENU BUTTON
WIDE(DOWN) BUTTON
POWER INPUT TERMINAL
DC 12V
POWER ON LAMP
( Please use a specified adaptor)
In power ON state ,
this LED is ON .
CAMERA CONTROL CONNECTOR
This is the 14 pin connector for external
camera controls .
( Refer to 4. CAMERA CONTROL METHODS )
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
3.1 Check all accessories with enclosed package .
- HZC-855NX/PX Ser. SET
- 14 PIN CONNECTION CABLE (150mm)
- OPERATION MANUAL
OPERATION MANUAL
HZC-855NX/PX Ser.
14 PIN CABLE*
* CABLE DESCRIPTION
1. KEY1
3. ZOOM
5. MENU
7. GND
9. R+/NC
11. T+/TD
13. EXT_VD
( RED )
2. KEY2
4. FOCUS
6. COM
( YELLOW )
( BLUE )
( ORANGE )
( BLACK )
( PINK )
( GREEN )
( WHITE )
( BLACK )
( BROWN )
( VIOLET )
( WHITE )
8. GND
10. R-/RD
12. T-/GND
14. GND
( GRAY )
( BLACK)
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Camera Control Methods
4.1 Remote Control using for Hard wired connection ( Connector pin 3,4,5,6 )
Controller
Relay
14P Cable
TELE (-)
WIDE(+)
ZOOM
3
14P Cable
NEAR(+)
4
5
FOCUS
MENU
Relay
FAR (-)
MENU ON
Relay
6
COM
4.2 Remote Control using for RS-232C connection ( Connector pin 10,11,12 )
Connect to Serial PORT
( COM1 or COM2 )
Serial Cable
14P Cable
Serial Cable
( 9 Pin D-Sub )
14P Cable
RD(TxD)
TD(RxD)
GND
2
10
11
12
RD
3
5
TD
SG
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3. Remote Control using for RS-422/485 connection ( Connector pin 9,10,11,12 ) -------- OPTION
Connect to Serial PORT
(COM1 or COM2)
485 Converter
Serial Cable
14P Cable
Serial Cable
( 9 Pin D-Sub )
14P Cable
RD(TxD)
TD(RxD)
GND
2
10
11
12
RD
3
5
TD
SG
422
RS-485 Converter
14P Cable
R +
R-
9
T+
10
11
T-
R+
T+
T-
R-
12
485
RS-485 Converter
14P Cable
TRxD+
R +
R-
9
10
11
TRxD-
T+
T-
12
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
Auto Mode
FUNCTION
Focus Mode
OSD Format
Non display
MF
5. On Screen Display
①
②
Manual / Oneshot Mode
Backlight OFF
Non display
⑧
⑧
Back Light
Flickerless
BL
Backlight ON
③,④
①
②
⑤
⑥
Non display
Flickerless OFF
Flickerless ON
③
FL
Non display
NTSC:1/60
1 / 125
Shutter Speed
Night Mode
.
9 variable steps
④
⑤
.
1 / 5 0, 0 0 0
Non display
IR
Nightshot OFF
⑦
⑧
Nightshot ON
Non display
IN
Auto Tracking WB mode
Indoor Preset (3200°K)
Outdoor Preset (5400°K)
<Fig5-1. Operating OSD display position>
5.1 How to display Operating OSD
a. Pressing the MENU key softly confirm current Operating OSD.
OUT
It is disappeared about five seconds later if there are no other key actions.
⑥
MWB
Manual WB mode
One Push mode
b. When it zoom in or out pressing TELE(up) or WIDE(down) key,
whole Operating OSD is displayed and then disappeared.
WB MODE
AWC
Press NEAR(+) , FAR(-) key, only upper part of Operating OSD
( for displaying camera mode ) is displayed and then disappeared.
(It is for checking current whole camera mode and zoom position )
AWB
Auto WB mode
Optical Zoom
Digital Zoom
x35
c. Even though Operating OSD is disappeared,
Dx90
ZOOM
DISPLAY
it keep displaying ID in lower part of screen.
In order to do not display ID, one method is to change EEPROM data
of Camera, the other is to use external communication through RS-232C.
zoom IN
>> TELE
<< WIDE
Non display
⑦
⑧
zoom OUT
d. Using RS-232C communication, change display position of ID;
Bottom Right -> Top Left -> Top Right -> Non display.
In case that ID is 0
CAMERA
ID/TITLE
ID : 002
In case that ID is 1 ~ 255
* If display Operating OSD is not needed by special purpose
like using external text overlay board, it can be OFF mode at all times
through external communication control as RS 232C.
TITLE
DISPLAY set as TITLE
<Table5-1. Operating OSD description>
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 OSD SETUP MENU Structure
ZOOM SPEED
START ZOOM
END ZOOM
E-ZOOM
1 ~ 10
x1 ~ x34
X35 ~ x90
ON/OFF
SETUP
LENS MODE
MENU
AF MODE
O. RESET
ONESHOT/MANUAL..
ON/OFF
O. AF TIME
AF SENS.
MIN. DIST.
1 ~ 10
HIGH/ LOW/AF SENS
1cm ~ INF.
MODE
AUTO/SHT FIX/IRIS...
2FLDS ~ 510 FIELDS
1/60 ~ 1/50000
CLOSE ~ F1.6
8 dB ~ 38 dB
LOW SHUTTER
HIGH SHUTTER
IRIS
AE MODE
WB MODE
GAIN
BRIGHTNESS
MAX GAIN
MAX FIELDS
0 ~ 99
8 dB ~ 38 dB
OFF ~ 510 FIELDS
MODE
ATW/AWC/MWB/…
AUTO/LOCK/…
0 ~ 255
CONTROL
RED GAIN
BLUE GAIN
MODE
OFF/AUTO/ON
1sec ~ 10 sec
BRT/CDS/BRT+CDS
0.1 lx ~ 100 lx
10 lx ~ 1000 lx
COLOR/ BW
0 ~ 255
DETECT TIME
DETECT MODE
D->N LEVEL
N->D LEVEL
NIGHT COLOR
NIGHTSHOT
MODE
MODE
LEVEL
BLC/H.BLC/WDR/…
0 ~ 15
BLC/WDR
MODE
ZONE NUM.
CONTROL
H START
H END
V START
V END
1 ~ 8
ON/OFF
6 ~ 658
106 ~ 758
6 ~ 407
PZM
SETTING
86 ~ 487
BLUE/RED/CYAN/…
CAMERA ID
DISPLAY
POSITION
0 ~ 255
CAM ID/TITLE
R.BOT/L.TOP/L.BOT…
CAMERA ID
SETTING
PZM MASKING
MIRROR
OFF/H MIRROR/…
0 ~ 15
ON/OFF
SPECIAL
FUNCTION
SHARPNESS
NEGATIVE
COLOR
ON/OFF
FREEZE
ON/OFF
BAUDRATE
PROTOCOL
F.OSD DISP.
4800bps ~ 512kbps
DEFAULT/VCL/KD6..
ALL/NONE/TOP/…
FACTORY
DEFAULT
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Display SETUP MENU
5.4 Quit SETUP MENU
a. Press MENU key above 2 seconds so that SETUP MENU 1 is
displayed on the screen.
b. Select item of SETUP MENU using TELE(up) / WIDE(down) key.
c. NEAR(+) / FAR(-) key is used to increase / decrease data of
selected item.
a. Press the MENU key again. SETUP MENU is disappeared,
“SAVE?” or “QUIT?” is displayed at center of screen.
If there is no change of adjustment state of Camera,
“QUIT?” is showed, else “ SAVE?” is showed.
① “QUIT?” : quit SETUP MENU without saving changed value.
② “SAVE?” : quit SETUP MENU with saving changed value.
b. Press NEAR / FAR key to choose, and press the MENU key again.
whole SETUP MENU is quitted.
( If MENU key is not pressed and TELE / WIDE key is pressed,
SETUP MENU is appeared again. )
<< SETUP MENU >>
LENS MODE
AE MODE
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
Setup menu1
<< LENS MODE >>
ZOOM SPEED
START ZOOM
END ZOOM
E-ZOOM
10
x1
x35
OFF
AF MODE
O.RESET
ONESHOT
OFF
O.AF TIME
AF SENS.
MIN. DIST.
RETURN
5 sec.
HIGH
50cm
<< LENS MODE >>
ZOOM SPEED
START ZOOM
END ZOOM
E-ZOOM
10
x1
x90
ON
Setup menu2
AF MODE
O.RESET
ONESHOT
OFF
5.5 LENS MODE
O.AF TIME
AF SENS.
MIN. DIST.
RETURN
5 sec.
HIGH
50cm
① ZOOM Speed Control
: Set zoom speed 1 to 10, 10 steps.
ZOOM SPEED
1 → 2 → … → 10
<Fig5-2. SETUP MENU change>
② Start Zoom Ratio
: Set boundary value of WIDE zooming.
5.3 Move between SETUP MENU 1 and SETUP MENU 2
START ZOOM
x 1 ~ x 34 ( in optical zoom region )
a. In order to change from SETUP MENU1 to SETUP MENU 2,
select NEXT MENU using TELE / WIDE key, and press
NEAR / FAR key.
b. In order to change from SETUP MENU 2 to SETUP MENU1 ,
select RETURN MENU using TELE / WIDE key, and press
NEAR / FAR key.
③ End Zoom ratio
: Set boundary value of TELE zooming. It can be set up to x90
including electronic zoom. ( in case the digital zoom limit is 2.5
times ) Since Start Zoom and End Zoom ratio are set,
simultaneously Camera moves to setting zoom times. So it can be
enable to adjust in moving to desired position.
END ZOOM
x 35 ~ x 90 ( in digital zoom region )
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
④ E-Zoom Control
⑥ ONESHOT AF RESET
: ON means up to x230, OFF means only optical zoom region.
: Use in case of focus deviation due to impact, vibration etc.
Auto Focusing is operated during set time.
E-ZOOM
OFF → ON → . . . .
O.RESET
OFF → ON → ….
⑤ Set Focus Mode
: It is composed of three modes.
☞ caution
1. It happens focus deviation according to circumstance condition
( brightness, facility to focus the object, etc ).
AUTO
:Use to focus automatically all the time.
⑦ ONESHOT AF TIME
MANUAL
: Set Oneshot AF operating time. When AF is completed, Focus mode
will be Manual. Though AF is not completed, it stops when time is
up.(unit:sec)
: Use to focus manually by pushing NEAR(+) / FAR(-)key.
Even though MANUAL mode, it will be focused in about 5 seconds
after zoom in(TELE) / out(WIDE), and return to MANUAL mode
automatically.
O.AF TIME
1 → 2 → … → 10
This is for focusing accurately after zooming.
⑧ AF Sensitivity
: HIGH : Reaction of Auto Focus is fast. It can be used when it shoot
ONESHOT
objects moving fast.
: It is similar to MANUAL mode. But there are some difference.
In case the focus mode is ONESHOT, it is focused whenever
ONESHOT (AUTO/MANUAL key) key is pushed. It will be returned
to MANUAL mode
after seconds (Special Menu : O.S. AF TIME) even though can not
be found best focus. In this case push ONESHOT(AUTO/MANUAL
key) key again, it will be in best focus.
LOW : Auto Focus is more stable. In fast moving scene, AF doesn’t
work even though the scene is changed. It is for stabilizing
the scene.
AF SENS.
HIGH → LOW → ….
⑨ Minimum Distance
: Set the minimum distance which can be focalized.
PUSHAUTO (option)
: While pushing key, Focus mode will be AUTO.
MIN. DIST.
1cm → 10cm → 50cm → 1m → 3m →
10m → INF.
☞ caution
1. According to Model , order is Auto -> Manual -> Oneshot, or Auto >
Manual -> Pushauto.
<< LENS MODE >>
ZOOM SPEED
START ZOOM
END ZOOM
E-ZOOM
AF MODE
O.RESET
O.AF TIME
AF SENS.
MIN. DIST.
RETURN
10
x1
x90
ON
MANUAL
OFF
5 sec.
HIGH
10cm
<< LENS MODE >>
ZOOM SPEED
START ZOOM
END ZOOM
E-ZOOM
AF MODE
O.RESET
10
x1
x90
ON
MANUAL
OFF
O.AF TIME
AF SENS.
MIN. DIST.
RETURN
5 sec.
HIGH
50cm
<Fig5-4. Minimum Focus Distance MODE>
<Fig5-3. LENS MODE >
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
② LOW SHUTTER Speed
: In Shutter Fix,Manual Mode, range is from 1/30 sec (2 fields)
to 2 sec (128 fields).
<< SETUP MENU >>
LENS MODE
AE MODE
LOW SHUTTER
OFF → 2 FLDS ~ 128FLDS
(FLDS means how many times integrated of CCD signal.)
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
③ HIGH SHUTTER Speed
: In Shutter Fix,Manual Mode, range is from 1/60 sec to
1/10,000 sec.
HIGH SHUTTER
1/60 → 1/100 → . . . . → 1/10000
④ IRIS
: In Iris Fix, Manual Mode, range is 17 phases from F1.6
(full Open) to CLOSE.
<Fig5-5. AE MODE >
IRIS
CLOSE → F22 → F19 → . . . . → F1.6
5.6 AE MODE
⑤ GAIN
: In Gain Fix, Manual Mode, range is 17 phases from 8 to 38dB.
① Exposure Mode
: It is composed of five modes according to circumstantial illuminance.
GAIN
OFF → 8dB → 10dB → . . . . → 38dB
AUTO
⑥ Brightness
: Exposure is controlled by Shutter Speed,Iris,Gain to meet the
Brightenss.
: Adjust level of Auto Iris. The smaller brightness value is, the darker
it is, because iris is closed more. On the contrary the bigger
brightness value is, the brighter it is, because iris is opened more.
SHUTTER FIX
BRIGHTNESS
0 ~ 99
: Low/High shutter speed is fixed, Exposure is controlled by Iris and
Gain.
⑦ MAX AGC
: Adjust Max AGC level.
MAX GAIN OFF→ 8dB → 10dB → . . . . → 38dB
IRIS FIX
: Iris is fixed, Exposure is controlled by Shutter Speed and Gain.
(Shutter Speed,GAIN is not adjust and operate automatically.)
☞caution
Max Gain is less than 14dB, and Field Integration does not work.
GAIN FIX
: Gain is fixed, Exposure is controlled by Shutter Speed and iris.
<< AE MODE >>
MANUAL
MODE
IRIS FIX
NOT USE
1/60
: Shutter Speed,Iris,Gain is fixed as set value regardless of
illuminance.
LOW SHUTTER
HIGH SHUTTER
IRIS
F5.6
☞ caution
GAIN
AUTO
40
34dB
1. There are menu items not to adjust and to skip according to
mode.
2. Field Integration is not operated in Shutter Fix, Gain Fix, Manual.
BRIGHTNESS
MAX GAIN
MAX FIELDS
RETURN
20FLDS
MODE
AUTO → SHT FIX → IRIS FIX →
GAIN FIX → MANUAL
<Fig5-6. Brightness in AE Mode >
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
⑧ MAX FIELDS (option)
5.7 White Balance Mode
: Use for compensating the low illumination condition. In case that use
this function because of low illumination condition, adjust maximum
integration fields to get brighter and dynamical image. But the scene
becomes slower than OFF mode. The larger max fields is,
simultaneously the noise of image is larger. This is phenomenon
because too small video output is integrated on many fields memory.
To get more dynamical image, adjust maximum integration fields
and set maximum AGC gain as HIGH, then make better the
standard of dynamic image.
① White Balance Mode
: Outer illumination condition is expressed by Color temperature,
Kelvin (°K). It is White Balance that shows white as white in any
illumination conditions. It is composed of five modes..
ATW ( Auto Trace White balance )
: Trace automatically under any condition in range 2,800°K ~ 8,000°K
( It can be adjustable red and blue point of desired white position. )
AWB
MAX FLDS
OFF → 2FLDS → 3FLDS → 4FLDS → 5FLDS
→ 6FLDS → 7FLDS → 8FLDS → …. →
→ 80FLDS → 160FLDS→ 320FLDS
→ 510FLDS
: Consider current illumination condition, do white balance by force
and lock as manual
INDOOR
☞caution
: Use to set the preset illumination condition as 3200°K
1. In Fields Integration mode, noises as well as video information are
increased. When an ambient temperature keeps high, CCD pixel
defect happens to be larger and white. This is not due to failure.
OUTDOOR
: Use to set the preset illumination condition as 5400°K
MANUAL
: Use to adjust to desired RED, BLUE gain manually.
<< SETUP MENU >>
LENS MODE
AE MODE
AWC
: Consider current illumination condition, do white balance by
force and lock as manual
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
② White Balance Mode Control
: It displays and changes White Balance Mode Control status of
Camera. ( According to Mode, it just display the state and not to
adjust.)
ATW
AUTO
INDOOR
OUTDOOR
MANUAL
AWC
3200°K
5400°K
R/B CONT
LOCK → PUSH → . . . .
AUTO
<< WB MODE >>
MODE
ATW
CONTROL
RED GAIN
BLUE GAIN
RETURN
FRAME
NOT USE
NOT USE
AWB
(LOCK means Manual white balance status. Press NEAR(+) /
FAR(-) key continuously, LOCK mode becomes PUSH mode and
white balance acts automatically, and then white balance mode is
locked as manual.)
<Fig5-7. WB MODE >
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
③ RED GAIN (Range is different on each Mode.)
④ Turnover LEVEL from DAY TO NIGHT
: Adjust RED Gain, and tune the sensitivity of white point.
: Set the LEVEL to turnover from Day to Night.
MANUAL
0 → 1 → …. → 254 → 255
D→N LEVEL
0.1 lx → 1 lx → 10 lx → ….
④ BLUE GAIN (Range is different on each Mode.)
⑤ Turnover LEVEL from NIGHT TO DAY
: Adjust BLUE Gain, and tune the sensitivity of white point.
: Set the LEVEL to turnover from Night to Day.
MANUAL
0 → 1 → …. → 254 → 255
N→D LEVEL
10 lx → 100 lx → 1000 lx → ….
⑥ Color on Nightshot Mode
: Set Color Mode on Night Mode.
NIGHT COLOR
B/W → COLOR → ….
<< SETUP MENU >>
LENS MODE
AE MODE
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
<< NIGHTSHOT MODE >>
MODE
AUTO
5sec
BRT
DETECT TIME
DETECT MODE
D->N LEVEL
N->D LEVEL
NIGHT COLOR
RETURN
1lx
100lx
B/W
5.8 NIGHTSHOT MODE
① NIGHTSHOT MODE
: It is used in low illumination condition. ON is Night mode, OFF is
normal state. Sensitivity of camera becomes more higher level like
BW camera.
It can be available external IR illuminator. In case of AUTO mode is
converted ON / OFF automatically according to illuminance change.
<Fig5-8. NIGHTSHOT MODE >
MODE
OFF → AUTO → ON → ….
<< SETUP MENU >>
LENS MODE
② NIGHTSHOT MODE DETECT TIME
AE MODE
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
: Set time to protect susceptible conversion of ON/OFF according to
illuminance change on Auto. When illuminace keeps the state during
detect time, convert ON/OFF.
DETECT TIME
1 sec. → 2 sec. → …. → 10 sec.
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
③ NIGHTSHOT DETECT MODE
: It is good to use with external IR illuminator on Auto. Select CDS
sensor ON/OFF to detect the illuminance state more effectively.
DETECT MODE
BRT → CDS → BRT+CDS → ….
<Fig5-9. BLC/BMB Mode >
☞ caution
BRT means shooting scene brightness, CDS sensor’s operation
depends on circumstantial brightness. Select to match with installation
circumstance.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5.9 BLC/ WDR Mode
<< SETUP MENU >>
LENS MODE
AE MODE
① Backlight Compensation Mode
: It is for preventing the center object too darken when the excessive
light is behind the center object. Set BACKLIGHT ON, then brighten
the center object in the contrast to the background light. Press
NEAR/ FAR key in 2 sec, Backlight mode become AUTO.
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
MODE
OFF → BLC → H.BLC → WDR → ….
H.BLC [Histogram BLC] is enhanced BLC function.
H. BLC makes the center object brighter to clear image
where the behind scene is too brighter than the center object.
<Fig 5-10. Privacy Zone Setting >
5.10 PRIVACY ZONE
② Backlight Compensation Level
BLC LEVEL
7 ( 0 ~ 15 )
① Set Privacy ZONE
:PZM(Privacy Zone Mask) is to hide the unwanted view to protect
privacy invasion. It works with Zoom/PAN/TILT operation. Select
PZM zone upto 8 zones.
③ Histogram BLC Level (H.BLC LEVEL)
H.BLC LEVEL
10 ( 0 ~ 15 )
ZONE NUM.
ZONE 1 → ZONE 2 → …. → ZONE 8
② PZM control
<< BLC/WDR MODE >>
: Set ON/OFF for each PZM Zone.
CONTROL
MODE
WDR LEVEL
RETURN
WDR
5
OFF → ON → ….
③ PZM Horizontal center starting point
: Set PZM for the starting point of Horizontal center.
H START
332
④ PZM Horizontal center ending point
: Set PZM for the ending point of Horizontal center.
H END
432
⑤ PZM Vertical center starting point
WDR [Wide Dynamic Range]
WDR is mostly useful function to take imag e from indoor to
window. WDR is the new technology to reduce the
differentiations between dark and bright areas.
: Set PZM for the starting point of vertical center.
V START
206
⑥ PZM Vertical center ending point
: Set PZM for the ending point of vertical center.
V END
286
④ WDR Level
WDR LEVEL
5 ( 0 ~ 15 )
⑦ PZM Masking
: Choose the Color to mask the PZM zone. 8 color
(Black,Gray, Light Gray,White,Red,Blue,Green,Yellow) is
available.
☞Cautions
1. While using WDR mode toward fluorescent lamp or bright
light, you may find out unwanted color. However, this is
normal condition for WDR function.
PZM MASKING
BLUE →RED → …. → GREEN
2. While using WDR mode, the digital zoom does not work.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick setting method for Privacy Zone Masking
5.11 Camera ID SET
1. Zoom in wide as possible as you can.
2. Select Zone Number in “ZONE NUM.”.
3. Select “On” by push the right button.
4. Push Menu button on the “CONTROL” to be able to move to
wanted position spot and push again to go back to main Menu.
5. Set the H and V value on the Menu.
① ID SET
: Camera ID is indicating number assigned each Camera in case of
controlling many Cameras. It is from 0 to 255. But in case of 0,
that is not displayed on screen. It is always displayed even though
whole Operating OSD is disappeared on the screen. But it is
possible to make non display and to choose display position
(BOTTOM RIGHT, TOP RIGHT, TOP LEFT) by RS-232C
communication.
6. Select a color.
7. Push Menu button to save the setting.
CAMERA ID
0 ~ 255
<< PRIVACY ZONE >>
☞ caution
ZONE NUM.
CONTROL
H START
H END
ZONE1
ON
332
1. In case of Camera ID FIX model, it cannot be selected..
2. ID is not changed by MENU control through communication.
432
V START
V END
PZM MASKING
RETURN
206
286
BLUE
② DISPLAY MODE
: Choose which is to display Camera ID or Title.
DISPLAY
CAM ID → TITLE → ….
PRESS MENU TO MOVE
③ DISPLAY POSITION
: Choose where is to display Camera ID or Title on Right Bottom,
Left Top, Right Top or not to display.
POSITION
R.BOT → L.TOP → R.TOP → NONE
<< CAMERA ID SET >>
TELE: ↑, WIDE: ↓
NEAR: →, FAR: ←
RETURN MENU
CAMERA ID
DISPLAY
001
CAM ID
R.BOT
POSITION
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz12345678
<Fig 5-11. Privacy Zone Setting >
9!?#$%&<>*,.:;/+-=~ ■
TITLE : HONEYWELL
RETURN
<< SETUP MENU >>
LENS MODE
AE MODE
WB MODE
<Fig 5-12. CAMERA ID Setting>
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
④ Title
: It is the name of Camera. It enters 10 characters including blank..
<< SETUP MENU >>
LENS MODE
AE MODE
WB MODE
TITLE: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
▣ How to Enter the Title ▣
Let’s enter the Title as “R1” , example
-. Select the position of title character by using Near or Far key.
The chosen position is blinking.
(Only chosen Cursor will be blink as “■”, rest of them
will be shown as a blank “ ”.)
5.12 SPECIAL FUNCTION
TITLE: □
① Mirror Mode
: Mode ON is Mirror Mode, OFF is general screen state.
-. Select the character “R” among ⓐ ~ ⓓ by using UP,DOWN,
(+),(-) key. The chosen character “R” is blinking.
MIRROR
OFF → H MIRROR →
V MIRROR → FLIP . . . .
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz12345678
9!?#$%&<>*,.:;/+-=~■
② Sharpness
: Use to change the contour of Scene.
SHARPNESS
0 ~ 15
③ Negative Mode
: Use for Positive and Negative mode. ON is Negative mode, OFF is
Positive mode namely general screen state.
-. Press MENU key, the character “R” is entered in the Title.
(Automatically the position will be forward to next position.)
NEGATIVE
OFF → ON → ….
TITLE: R □
④ Color Mode
: Use for changing color and monochrome ( black & white )mode .
ON is Color mode, OFF is black&white mode.
-. If you want to edit specified character, you shall use
TELE/Wide to move on the position and NEAR/FAR to
select on the character. By using TELE/WIDE to position
the character to continue to edit.
COLOR
ON → OFF → ….
-. Select character “1” using TELE, WIDE, NEAR, FAR
button and it will blink the cursor on the character “1”
<< SPECIAL FUNCTION >>
MIRROR
OFF
SHARPNESS
NEGATIVE
COLOR
8
OFF
ON
OFF
9600bps
DEFAULT
ALL
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz12345678
9!?#$%&<>*,.:;/+-=~■
FREEZE
BAUDRATE
PROTOCOL
F. OSD DISP
RETURN
-. Push MENU to enter the character “1”.
TITLE: R 1 □
<Fig 5-13. SPECIAL FUNCTION>
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
⑤ Freeze Mode
: It pause current image. ON is to stop, OFF is to return to normal
state.
FREEZE
ON → OFF → ….
☞ caution
1. Freeze image does not save when you reset the system.
This system doesn’t have its’ own memory.
⑥ BAUD RATE
: Use to communicate through RS232C, RS485, RS232TTL .
BAUDRATE
4800bps → 9600bps → ….
→ 312kbps
☞ caution
1. If the Baud Rate does not match between Camera and external
system, it may occur the communication failure. Please make
sure a proper Baud Rate.
⑦ PROTOCOL Setting
: Setting the PROTOCOL with communication device.
PROTOCOL
DEFAULT → VCL → KD6 → P/D
→
….
⑧ Function OSD Display
OSD DISP
ALL → NONE → TOP →
BOTTOM → ....
ALL
: Whole Function OSD display
( Focus Mode, Key state, Zoom Ratio, ID )
: Only Upper OSD display ( Focus Mode, key
state )
TOP
BOTTOM : Only Lower OSD display ( Zoom Ratio, ID )
NONE
: All the OSD will not display except MENU
OSD.
☞ Caution
1. The display of ID and TITLE can be only set in CAMERA ID
SETTING.
5.13 Initial Set
: Set the INITIAL SET Mode ON so that all changed data are
returned to shipping condition. For Initialization, select “YES?” by
using NEAR, FAR key and push MENU key. Select “NO?”
and push MENU, no initialization and return to Main Menu.
☞ caution
1. Make sure when Initialization set as “YES?” , all changed data are
return to shipping condition.
2. Some menu as ID,TITLE, etc are not initialized.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Specification
Model Name
HZC-855NX
HZC-855NX-VR
HZC-855PX
HZC-855PX-VR
1/4” Sony Double Scan CCD ( Ex- View CCD )
Pick up Device
410,000 / 380,000
470,000/440,000
Total/Effective Pixels
Scanning System
Lens
2:1 Interlace
Optical x35, f = 3.6~126mm, F1.65(WIDE) ~ F4.2(TELE)
x36 ~ x90 can be adjustable
Digital Zoom Ratio
Sync. System
H. Resolution
S/N Ratio
Internal line lock/ VD pulse lock( AutoDetect)
More than 530 TV Lines
More than 50 dB ( AGC OFF )
More than 49 dB ( AGC OFF )
0.5 lx (30IRE) ; 0.05 lx (IR FILTER OFF) ;
0.6 lx (30IRE) ; 0.06 lx (IR FILTER OFF) ;
Min. illuminance
0.0005 lx (510 fields) ; 0.00001 lx (510 fields, IR FILTER
OFF)
0.0006 lx (510 fields) ; 0.00001 lx (510 fields, IR
FILTER OFF)
Auto / Manual / Oneshot
Focus Mode
0 ~ 99 adjustable
1/60(50) ~ 1/50,000
Brightness
Shutter Speed
Field Integration
Mirror
x2 ~ x510 adjustable
Horizontal Mirror / Vertical Mirror / FLIP(Horizontal Mirror + Vertical Mirror )
AUTO / ON / OFF ( CDS Sensor ON/OFF)
ON ( Max 8 area ) / OFF
Day & Night Mode
Privacy Zone
ON ( 8 ~ 38dB ) / OFF
AGC
AUTO(ATW, AWC) / OneShot / Indoor / Outdoor / Manual /AWB
BLC : ON / OFF / H.BLC ,/ WDR
White Balance
BLC ( BMB )
RS-232C
RS-422 / RS-485
RS-232C
RS-422 / RS-485
Remote Control
Power Supply/Consump.
Operation/Storage Temp.
Dimension / Weight
DC 9V ~ DC 14V ( Motor Activate 6 W , Motor Stop 4.0 W )
-10 ~ 60 ℃( Recommended -5 ~ 50 ℃) / -20 ~ 60 ℃
62 x 71.6 x 116 (mm) / 510g
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Dimensions
VIDEO
SVIDEO
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Honeywell Co., Ltd.
Address : 17F, Kukje Center Building 191, Hankangro -2ga,
Yongsan-gu, Seoul 140-702, Korea
Phone : 82-2-799-6109, 6108, 6107, 6292
Fax : 82-2-749-6119
Printed in Korea
G-113864-001
http : //www.honeywell.co.kr/security/english
E-mail : [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|