M6410A, M7410F Actuators
V5862A,V5863A Valves
HIGH-FORCE NON-SPRING RETURN ACTUATORS
AND 1, 1-1/4, 1-1/2 INCH NPT CARTRIDGE GLOBE VALVES
M6410A and M7410F Series 3000 Non-Spring Return Valve
Actuators provide floating or modulating control of V5862A
and V5863A Series 3000 Cartridge Globe Valves.
SPECIFICATION DATA
FEATURES
The actuators are used in electronic temperature control
systems, which use hot and/or cold water (with glycol up to
50 percent) as the controlled medium in variable air volume
(VAV) terminal units, fan-coil units, small reheaters and
recoolers.
•
•
Small size allows installation in limited space.
Long stroke allows wider range of control.
Actuators
•
•
•
•
•
•
•
Low power consumption.
Synchronous motor.
No mounting tools required.
Low-maintenance plastic housing.
Conduit connector standard.
No separate linkage required.
M6410A provides 3-position floating control without
proportional feedback.
SPECIFICATIONS
CAUTION
Equipment Damage Hazard.
Installing a high-force (67.5 lb [300 N]) actuator on
1/2 or 3/4 in. valve can damage the valve beyond
repair.
•
M7410F receives 0 to 10 Vdc or 2 to 10 Vdc input
signal, selectable at the site.
•
•
M7410F includes direct/reverse acting switch.
Especially suitable for Excel Controller or Individual
Room Controller (IRC) System.
Use only Series 1000 (40.5 lb [180 N]) actuators with
the smaller (1/2 in. and 3/4 in.) valves.
®
•
•
Internal valve position indicator.
Magnetic coupling for torque limitation independent of
voltage supply, and self-adjustment of close-off port.
Ready-to-wire connecting cable.
CAUTION
Electrical Shock or Equipment Damage Hazard.
Can shock individuals or short equipment
circuitry.
•
Disconnect power supply before installation.
Valves
•
•
•
•
•
V5862A is a two-way female NPT valve.
IMPORTANT
V5863A is a three-way female NPT mixing valve.
Pressure-balanced plug.
— A low-force (40.5 lb [180 N]) actuator installed on a
valve larger than 3/4 in. cannot operate the valve.
— Install high-force actuators (67.5 lb) only on large
valves (1 in., 1-1/4 in., 1-1/2 in.).
Soft valve seat provides low leakage rate.
Valve inserts are changeable with the insert
replacement tool.
Threaded plastic cover allows manual operation.
Brass body and stainless steel stem.
Models:
•
•
❑ M6410A: Non-Spring Return Valve Actuator. Provides
floating control of the V5862A and V5863A Valves.
❑ M7410F: Non-Spring Return Valve Actuator. Provides
modulating control of V5862A and V5863A Valves.
❑ V5862A: Two-way NPT Valves.
Mounting:
❑ Actuator screws onto valve body.
❑ V5863A: Three-way NPT Mixing Valves.
Control Modes:
❑ M6410A: Floating.
❑ M7410F: Modulating.
Connections:
❑ M6410A, M7410F: 4.9 ft (1.5m) cable.
Electrical Ratings:
❑ Input Power:
Ambient Ratings:
❑ Operating Temperature Range: 32° to 122°F (0° to 50°C).
❑ Storage Temperature Range: -40° to 158°F (-40° to 70°C).
❑ Humidity Range: 5 to 95% RH (noncondensing).
❑ 24 Vac, +10/-30 percent, 50/60 Hz.
❑ Power Consumption:
❑ M6410A: 0.7 VA.
❑ M7410F: 1.4 VA.
Weight:
❑ M6410A: 5 oz (0.15 kg).
❑ M7410F: 5.6 oz (0.16 kg).
❑ Input Signal (M7410F): Modulating 0 to 10V, 2 to 10V
(adjustable), 0.1 mA.
❑ Input Impedance (M7410F): 100K ohms.
® U.S. Registered Trademark
Copyright © 2004 Honeywell International Inc.
All Rights Reserved
63-1293-2
Download from Www.Somanuals.com. All Manuals Search And Download.
M6410A, M7410F ACTUATORS V5862A,V5863A VALVES
Dimensions in in. (mm):
2
-
5
/
1
6
(
5
8
)
MINIMUM CLEARANCE
9-7/8
(250)
STROKE 1/4 (6.5)
23/32
(18)
G
3
(
-
1
5
/
1
)
6
1
0
0
E
D
A
C
C
1
/
2
(
1
3
)
F
2
-
3
/
8
(
6
1
)
1
-
1
4
5
/
1
6
B
(
9
)
M
8
2
2
5
A
VALVE SIZE
A (NPT)
B
C
D
E
F
G
Non-Spring Return Actuators
(M6410A, M7410F)
1
(25)
1-1/4 (32) 4-15/16 (125)
1-1/2 (38) 5-1/8 (130) 2-3/16 (55) 2-9/16 (65) 3-7/8 (98) 2-3/8 (60) 2-11/16 (69)
4-1/8 (105) 1-5/8 (41) 2-1/16 (53) 3-5/8 (92)
2
(50)
2-5/16 (58)
2 (50)
2-7/16 (62) 3-5/8 (92) 2-3/16 (55) 2-5/16 (58)
V5862 FLOW
V5863 FLOW
OUTLET
PORT AB
PORT A
INLET
PORT B
M19619A
3
63-1293—2
Download from Www.Somanuals.com. All Manuals Search And Download.
M6410A, M7410F ACTUATORS V5862A,V5863A VALVES
TYPICAL SPECIFICATION
Cartridge Globe Valves
Cartridge globe valve supplier must be Honeywell.
Valves shall be available in two- and three-way
mixing models with brass bodies and stainless
steel stem. Valves must have nominal rangeability
of 50:1 or better. Valves must have a leakage rating
less than 0.05% of the Cv.
Valves 1 in. or larger must be pressure balanced.
Valves shall be usable with hot water, chilled water,
or glycol solutions up to 50 percent. Valves must
have available insert replacement tools to facilitate
changing the cartridge.
Cartridge Globe Valve Actuators
Cartridge globe valve actuator supplier must be
Honeywell. Electric actuators shall provide either
floating or modulating control of two- and three-
way cartridge globe valves. Actuator will operate
at 24 Vac (+10/-30%) and 50/60 Hz. Actuator must
screw onto compatible valve body without the aid
of mounting tools. Actuators shall have an
ambient temperature rating of 32 to 122 degrees
Fahrenheit.
P
p
p
r
i
n
t
e
d
i
n
U
.
S
n
.
A
.
o
a
n
t
r
e
c
y
c
l
e
d
63-1293—2 B.B. Rev. 4-04
/building/components/
a
o
p
s
e
r
c
c
o
n
t
a
i
i
n
r
g
l
e
a
s
t
1
r
0
%
t
-
o
n
s
u
m
e
p
a
p
e
r
f
i
b
e
s
.
Download from Www.Somanuals.com. All Manuals Search And Download.
|