®
Model No. HREVEL05983
Serial No.
USER’S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, we will guarantee complete
satisfaction through our Customer
Service Department.
Please CALL:
0345-089009
Or WRITE:
ICON HEALTH AND FITNESS LTD.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical crosstrainer.
1. Read all instructions in this manual before
using the elliptical crosstrainer.
as an exercise aid in determining heart rate
trends in general.
2. It is the responsibility of the owner to ensure
that all users are adequately informed of all
precautions.
10. When you stop exercising, allow the pedals
to slowly come to a stop.
11. Keep your back straight when using the ellip-
tical crosstrainer. Do not arch your back.
3. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrain-
er indoors, away from moisture and dust.
12. If you feel pain or dizziness whilst exercis-
ing, stop immediately.
4. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
13. The elliptical crosstrainer is intended for in-
home use only. Do not use it in any commer-
cial, rental, or institutional setting.
5. Keep children under age 12 and pets away
from the elliptical crosstrainer at all times.
14. The decal shown below is found on the ellip-
tical crosstrainer. If the decal is missing or
illigible, please call our Customer Service
Department at 0345-089009 to order a free
replacement. Apply the decal in the location
shown.
6. Always hold the handlebar or the upper
body arms when mounting, dismounting, or
using the elliptical crosstrainer.
7. Wear appropriate exercise clothing when
using the elliptical crosstrainer. Always wear
athletic shoes for foot protection.
8. The elliptical crosstrainer should not be used
by persons weighing more than 250 pounds
(115 kgs).
9. The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the revolutionary
HealthRider® E330 elliptical crosstrainer. The
HealthRider® E330 is an incredibly smooth exerciser
that moves your feet in a natural elliptical path, min-
imising the impact on your knees and ankles. And the
unique E330 features adjustable resistance and
incline to help you get the most from your exercise.
Welcome to a whole new world of natural, elliptical-
motion exercise from HealthRider.
al questions, please call our Customer Service
Department at 0345-089009. To help us assist you,
please note the product model number and serial
number before calling. The model number is
HREVEL05983. The serial number can be found on a
decal attached to the HealthRider® E330 (see the front
cover of this manual for the location of the decal).
Before reading further, please look at the drawing
below and familiarise yourself with the parts that are
labelled.
For your benefit, read this manual carefully before
you use the HealthRider® E330. If you have addition-
Book
Rack
Upper Body Arm
Console
Handlebar with Pulse Sensor
Resistance Control
FRONT
Incline Frame
Incline Bracket
Pedal Disk
RIGHT SIDE
BACK
Pedal
Pedal Arm
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. If assistance is needed,
please call our Customer Service Department at 0345-089009.
Assembly requires the following tools: the included allen wrench, a phillips screwdriver
an adjustable spanner , a rubber mallet , and pliers
,
.
During assembly, use the drawings below to identify the small parts used in assembly. The number in parenthe-
sis below each drawing refers to the key number of the part, from the PART LIST on page 18. The second num-
ber refers to the quantity used in assembly. Note: Some small parts may have been pre-attached. If a part is
not in the parts bag, check to see if it has been pre-assembled.
Spacer
(44)–4
M8 Nylon
Locknut (80)–2
M8 Split
Washer (58)–2
M10 Nylon
Locknut (26)–7
M8 Washer (81)–6
Nylon Washer
(11)–2
M10 x 85mm Bolt (25)–1
M4 x 16mm
Flange Screw
(43)—6
M4 x 16mm
Screw (35)–9
M10 x105mm Carriage Bolt (27)–2
M8 x 108mm Button Head Bolt (79)–2
Axle Screw (30)–2
1. Hold the Rear Stabiliser (65) against the saddle on the
rear of the Frame (1). Make sure that the Rear
Stabiliser is turned so the square holes are facing away
from the Frame. Attach the Rear Stabiliser with two
M10 x 105mm Carriage Bolts (27) and two M10 Nylon
Locknuts (26).
1
26
65
26
1
27
2. Turn the Resistance Control (57) counterclockwise to
the minimum setting.
2
If the Resistance Control (57) is attached to the Upright
(2), remove the M4 x 16mm Screw (35). Pull the bot-
tom of the Resistance Control away from the Upright
and then slide it down to remove it.
2
Tab
57
35
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lay a cloth over the front of the Frame (1) to protect it.
Lay the Upright (2) in the position shown. Connect the
Extension Wire (51) to the Reed Switch Wire (50).
3
2
57
84
Next, connect the Resistance Cable (57) to the
Extension Cable (84) in the following way:
51
• Refer to drawing A. Pull up on the metal bracket, and
insert the tip of the Resistance Cable (57) into the
wire clip on the Extension Cable (84) as shown.
1
50
B
• Refer to drawing B. Firmly pull the Resistance Cable
(57) and slide it into the metal bracket on the
Extension Cable (84) as shown.
A
Metal
Bracket
C
• Refer to drawing C. Using pliers, squeeze the prongs
on the upper end of the metal bracket together.
57
57
57
84
4
84
84
4. Align the two holes in the front of the Upright (2) with
the two welded bolts on the front of the Frame (1).
Carefully push the Reed Switch Wire (not shown) into
the Upright until there is no slack.
26
2
Next, pivot the Upright (2) about halfway to the vertical
position whilst guiding the metal bracket on the
Extension Cable (not shown) into the Upright. Once
the top edge of the metal bracket is inside the Upright,
pivot the Upright to the vertical position so it rests on
the four welded bolts on the Frame (1). Be careful to
avoid pinching the wires. Tighten an M10 Nylon
Locknut (26) onto each welded bolt.
Welded
Bolts
Refer to assembly step 2. Insert the tab on the Resis-
tance Control (57) into the Upright (2). Next, press the
bottom of the Resistance Control against the Upright.
Tighten the M4 x16mm Screw (35) into the Resistance
Control and the Upright.
1
5. Attach the Incline Bracket (24) to the lower end of the
Upright (2) with the M10 x 85mm Bolt (25) and an M10
Nylon Locknut (26). Do not overtighten the Nylon
Locknut; the Incline Bracket must pivot easily.
5
24
2
26
25
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Slide an M8 Split Washer (58) and an M8 Washer (81)
onto an Axle Screw (30). Tighten the Axle Screw into
one end of the Incline Axle (29). Next, apply a small
amount of the included grease to the Incline Axle.
6
V-shaped Groove
Align the indicated tubes on the Incline Frame (5) with
the tubes on the Base (1). Make sure that the Incline
Frame is turned so the V-shaped grooves are on
top. Insert the Incline Axle (29) through the Incline
Frame and the Base. Note: It may be helpful to tap the
Incline Axle with a rubber mallet to insert it.
5
58
81
1
30
Slide an M8 Split Washer (58) and an M8 Washer (81)
onto the other Axle Screw (30). Tighten the Axle Screw
into the open end of the Incline Axle (29).
Grease
81
Tubes
58
29
Tubes
30
7. The Console (87) requires two 1,5V batteries (not
included). Alkaline batteries are recommended. To
install batteries, turn the console over and insert two
batteries into the battery clip as shown in the inset
drawing. Make sure that the negative ends of the
batteries (marked “—”) are touching the springs in
the battery clip.
7
87
Batteries
53
Battery
Clip
Attach a Plastic Tie (53) to the battery clip as shown.
49
Attach the Console (87) to the Console Base (49) with
four M4 x 16mm Screws (35), making sure that the
indicated wires are extending from the Console Base
(49). Be careful not to pinch the wires.
Wires
35
8. Connect the Extension Wire (51) to the corresponding
wire on the Console (87).
8
87
Next, connect the two Pulse Wires (86) to the two
remaining wires on the Console (87). Note: Either
Pulse Wire can be attached to either wire on the
Console.
Console
Wires
49
35
Ground Wire
Next, connect the ground wire to the indicated hole in
the Upright (2) with an M4 x 16mm Screw (35).
86
51
Carefully feed the wires down into the Upright (2).
Attach the Console Base (49) to the Upright with four
M4 x 16mm Screws (35). Be careful to avoid pinch-
ing the wires.
35
35
2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Identify the Left Pedal Arm (3), which has an “L” sticker
on it. Be careful not to confuse the Left Pedal Arm
with the Right Pedal Arm (not shown); look at the
position of the round tube in the inset drawing to
identify the Left Pedal Arm. Next, identify the Left
Pedal (41), which has the letter “L” molded onto the
bottom.
9
43
3
Turn over the Left Pedal Arm (3) as shown. Insert the
three plastic posts on the Left Pedal (41) into the three
indicated holes in the Left Pedal Arm. Make sure that
the Left Pedal is turned as shown. Attach the Left
Pedal with three M4 x 16mm Flange Screws (43).
Open Side
Plastic Posts
41
Attach the Right Pedal (not shown) to the Right Pedal
Arm (not shown) in the same way.
Round
Tube
3
Open Side
10.Apply grease to an M8 x 108mm Button Head Bolt (79).
Slide an M8 Washer (81) onto the Bolt and insert the
Bolt into the indicated side of the Left Pedal Arm (3).
Be careful not to confuse the Left Pedal Arm with
the Right Pedal Arm (not shown); look at the posi-
tion of the round tube to identify the Left Pedal
Arm. Next, slide a Spacer (44), a Pedal Wheel (77),
and another Spacer (44) onto the Bolt and push the
Bolt through the other side of the Left Pedal Arm.
10
21
Grease
81
80
82
81
Next, slide a Tube Spacer (82), a Chrome Tube (21),
and an M8 Washer (81) onto the M8 x 108mm Button
Head Bolt (79). Tighten an M8 Nylon Locknut (80) onto
the Bolt.
Round
Tube
44
77
79
Attach the other Chrome Tube (not shown) to the Right
Pedal Arm (not shown) in the same way.
3
44
10a
80
Front
View
3
82
81
79
21
81
44
44
77
8
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Apply a small amount of grease to the axle on the left
Crank Arm (6).
11
Slide a Nylon Washer (11) and the Left Pedal Arm (3)
onto the axle on the left Crank Arm (6). Note: It may be
helpful to use a rubber mallet to tap these parts on. Be
careful not to confuse the Left Pedal Arm with the
Right Pedal Arm (not shown); look at the position
of the round tube to identify the Left Pedal Arm.
Next, tap a 3/4” Axle Cap (61) onto the axle.
Grease
6
3
11
Attach the Right Pedal Arm (not shown) in the same way.
61
Round Tube
12. Refer to the inset drawing. Apply a small amount of
the included Teflon® lubricant to a paper towel; rub a
thin film of the lubricant onto each of the Chrome
Tubes (21). Slide an Upper Body Arm (7) onto each
Chrome Tube. Make sure that the Upper Body Arms
are turned as shown.
12
7
85
19
21
Tap a 5/8” Axle Cap (85) onto one end of the Axle
(19). Insert the Axle through one of the Upper Body
Arms (7) and then through the Upright (2). Slide the
other Upper Body Arm (7) onto the Axle. Tap another
5/8” Axle Cap (85) onto the Axle.
Lube
4
85
7
2
7
13. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware
may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat
under the elliptical crosstrainer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL CROSSTRAINER
EXERCISING ON THE ELLIPTICAL CROSSTRAINER
To dismount the elliptical crosstrainer, wait until the
pedals come to a complete stop. Important: The
elliptical crosstrainer does not have a freewheel;
the pedals will continue to move until the flywheel
stops. When the pedals are stationary, step off the
highest pedal first. Then, step off the lowest pedal.
To mount the elliptical crosstrainer, hold the handlebar
and step onto the pedal that is in the lowest position.
Next, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The pedal disks can turn in either direction. It is
recommended that you move the pedal disks in
the direction shown below; however, to give vari-
ety to your exercise, you may choose to turn the
pedal disks in the opposite direction.
HOW TO ADJUST THE RESISTANCE
To adjust the
intensity of your
exercise, the
resistance of the
pedals can be
adjusted. To
Pedal Disk
Pedal
increase the
resistance, turn
the resistance
control clockwise;
to decrease the
resistance, turn
the control coun-
terclockwise.
Control
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INCLINE ADJUSTMENT
DESCRIPTION OF THE CONSOLE
The incline frame can be raised or lowered to vary the
intensity of your exercise. To raise the incline frame,
lift the end of the incline frame until the crossbar is on
top of the incline bracket. Make sure that the incline
frame is resting securely on top of the incline
bracket. To lower the incline frame, first lift the incline
frame slightly. Next, push the incline bracket toward
the upright and lower the incline frame onto the sta-
biliser.
The innovative
console offers a
manual mode and
three pacer pro-
grams. The pacer
programs are
designed to help
you reach specific
exercise goals by
pacing your exer-
cise. You can
choose from a sta-
mina-building
Upright
Interval program,
an Aerobic pro-
Incline
Bracket
gram, and a spe-
cial Fat Burn pro-
gram. As you
Crossbar
Incline
exercise, seven
monitor modes will
provide continuous exercise feedback. The monitor
modes are described below:
Frame
Stabiliser
Speed—This mode shows your exercising pace,
in kilometres or miles per hour (see HOW TO
SELECT KILOMETRES OR MILES on page 13).
USING THE UPPER BODY ARMS
The upper body arms are designed to give you a total
body workout. As you exercise, hold the upper body
arms and move your arms forward and back in order
to work your arms, back, and shoulders.
Time—If you select the manual mode, this mode
will show the elapsed time. If you select one of
the three pacer programs, this mode will count
down the time remaining in the program.
If you want to exercise only your lower body, hold the
handlebar as you exercise.
Distance—This mode shows the distance you
have strided, in kilometres or miles.
Lap—This mode shows the number of laps you
have completed. One lap equals 0.25 kilometres
or miles.
Upper
Body
Arms
Calorie—This mode shows the approximate
number of calories you have burned.
Scan—This mode displays the above five
modes, for 5 seconds each, in a repeating cycle.
Handlebar
Pulse—This mode shows your heart rate when
the pulse monitor is used. (See step 5 on
page 13.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW THE PACER PROGRAMS OPERATE
Select one of the three pacer programs or the
manual mode
2
When you use a
pacer program, two
To select one
Actual
columns of bars will
appear in the dis-
play. The left col-
umn represents a
target pace and the
right column shows
your actual exercis-
ing pace. The target pace will change periodically dur-
ing the program; as the target pace changes, simply
adjust your exercising pace to keep both columns at
the same height. Important: The target pace is a
goal pace. Your actual pace may be slower than the
target pace, especially during the first few months
of your exercise program. Be sure to exercise at a
pace that is comfortable for you.
of the pacer
programs,
repeatedly
Program Indicator
press the pro-
gram button.
The program
indicator will
show which
program you
have selected.
To select the
manual mode, press the program button until the
program indicator disappears. The programs will
be selected in the following order: program 1
(Interval), program 2 (Aerobic), program 3 (Fat
Burn), manual mode.
Target
Program Button
The three graphs on
the console show
how the target pace
will change during
Begin your workout
If you select-
3
the programs.
During the Aerobic
program (P2), for
example, the target pace will gradually increase during
the first half of the program, and gradually decrease
during the last half of the program. Each program will
last for twenty minutes.
ed the manual
mode, go to
step 4. If you
selected one of
the pacer pro-
grams, two
Actual
Target
columns of
bars will
STEP-BY-STEP CONSOLE OPERATION
appear in the display. The left column will show
one bar, indicating a relatively slow pace. The
right column will show your actual exercising
pace. Adjust your exercising pace until only one
bar appears in the right column. Each time the
target pace changes during the program, adjust
your exercising pace to keep both columns at the
same height.
Before the console can be operated, two batteries
must be installed. (See assembly step 7 on page 7.)
Follow the steps below to operate the console.
Turn on the power
1
To turn on the
Follow your progress with the LED track and
the seven monitor modes
4
power, press the
On/Reset
on/reset button
Button
or simply begin
The LED track—
exercising. The
The LED track
entire display will
represents a dis-
appear for two
tance of 0.25
seconds; the console will then be ready for use.
Note: If batteries were just installed, the power will
already be on.
kilometres or
miles. As you
exercise, the
indicators around
the track will light one at a time until you have com-
pleted one lap. A new lap will then begin.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the contacts
for about 15 seconds.
The scan
mode—
Repeatedly
press the
mode button
until an arrow
appears
under the
scan symbol.
When the
scan mode is
selected, the
console will display the speed, time, distance, lap
and calorie modes, for 5 seconds each, in a
repeating cycle.
Mode
Arrow
Make sure that your hands are positioned as
described above, and that you are not moving
your hands excessively or squeezing the metal
contacts too tightly.
Mode
Button
Turn off the power
6
To turn off the power, simply wait for about
six minutes. If the pedals are not moved and the
console buttons are not pressed for six minutes,
the power will turn off automatically.
The speed,
HOW TO SELECT KILOMETRES OR MILES
time, dis-
tance, lap,
The console can
or calorie
display distance
mode—
and speed in
Repeatedly
either kilometres
press the
or miles. If a
mode button
“KPH” appears in
until an arrow appears below or above the
desired mode symbol. Make sure that there is not
an arrow under the scan symbol.
the display, dis-
tance and speed
will be shown in kilometres; if a “KPH” does not
appear, distance and speed will be shown in miles.
The pulse mode—To use the pulse mode, see
step 5.
To change the
unit of measure-
ment, first
To reset the display, press the on/reset button.
remove the four
indicated screws
from the con-
sole. Lift the
console a few
inches and turn
Measure your heart rate if desired
5
To use the
pulse sensor,
place your
hands on the
Metal
Contacts
it over; be care-
Switch
metal con-
ful not to pull
tacts. Your
on the wires.
palms must
be resting on
the upper
contacts and
Next, locate the
small switch on
the back of the
Screws
your fingers
console. Slide the switch up or down to change the
unit of measurement. Reattach the console with the
four screws; be careful not to pinch any of the
wires.
must be touching the lower contacts. Avoid mov-
ing your hands. After a moment, the heart-shaped
indicator in the display will begin to flash and your
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Inspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.
HOW TO LEVEL THE ELLIPTICAL CROSS-
TRAINER
For smooth
If the elliptical
crosstrainer
does not sit
flat on the
floor, one or
both of the
levelling pads
should be
Incline
Frame
operation of
the elliptical
crosstrainer,
the incline
frame should
be kept clean.
Using a soft
cloth and mild
detergent,
Jam
Nut
Pad
adjusted.
Wheel
First, loosen
the jam nut on
each levelling
pad. Next,
clean dust and
other residue
from the incline
frame where the wheels make contact with it. Other
parts of the elliptical crosstrainer can also be cleaned
in this manner. Never use abrasives or solvents.
turn the levelling pads as needed until the elliptical
crosstrainer is level. When the levelling pads are
properly adjusted, firmly retighten the jam nuts.
PULSE SENSOR TROUBLE-SHOOTING
LUBRICATING THE INCLINE BRACKET
• Avoid moving your hands whilst using the pulse
sensor. Excessive movement may interfere with
heart rate readings.
The incline
bracket and the
bolt on which it
pivots should be
regularly lubricat-
ed. Apply a small
amount of the
included lubricant
to the bolt and
between the
Upright
Incline
Bracket
Bolt
• Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
• For the most accurate heart rate reading, hold the
metal contacts for about 15 seconds.
• For optimal performance of the pulse sensor, keep
the metal contacts clean. The contacts can be
cleaned with a soft cloth—never use alcohol,
abrasives, or chemicals.
bracket and the
upright.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following basic guidelines will help you to plan
your exercise program. For more detailed information,
obtain a reputable book or consult your physician.
Burning Fat
To burn fat, you must exercise at a low intensity level
for a sustained period of time. During the first few
minutes of exercise, your body uses easily accessible
carbohydrate calories for energy. Only after the first few
minutes of exercise does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the intensity of your exercise until your heart rate is
near the low end of your training zone as you exercise.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over the age of 35 or persons with pre-exist-
ing health problems.
WARNING:
The pulse sensor is
EXERCISE INTENSITY
not a medical device. Various factors may
affect the accuracy of heart rate readings. The
pulse sensor is intended only as an exercise
aid in determining heart rate trends in general.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. For effective exercise, your heart
rate should be maintained at a level between 70% and
85% of your maximum heart rate as you exercise. This
is known as your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the intensity of your exercise until your heart
rate is near the middle of your training zone.
You can find your training zone in the table below.
Training zones are listed according to age and physi-
cal condition.
UNCONDITIONED
TRAINING ZONE
(BEATS/MIN)
CONDITIONED
TRAINING ZONE
(BEATS/MIN)
AGE
20
25
30
35
40
45
50
55
60
65
70
75
80
WORKOUT GUIDELINES
138-167
136-166
135-164
134-162
132-161
131-159
129-156
127-155
126-153
125-151
123-150
122-147
120-146
133-162
132-160
130-158
129-156
127-155
125-153
124-150
122-149
121-147
119-145
118-144
117-142
115-140
Each workout should include three important parts:
(1) a warm-up, (2) training zone exercise, and (3) a
cool-down.
Warming up
Warming up prepares the body for exercise by
increasing circulation, delivering more oxygen to the
muscles, and raising the body temperature. Begin
each workout with 5 to 10 minutes of stretching and
light exercise to warm up.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 30 minutes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooling Down
EXERCISE FREQUENCY
Finish each workout with 5 to 10 minutes of stretching.
Stretching after exercise develops flexibility and helps
prevent post-exercise problems.
To maintain or improve your condition, plan three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the
right. Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
3
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for each leg. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. HREVEL05983
R0500A
Key
No.
Key
No.
Qty.
Description
Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
2
1
2
1
3
1
1
2
1
1
2
2
1
2
2
4
6
1
1
9
2
1
1
2
6
4
4
1
17
1
1
2
1
2
1
1
6
4
2
2
1
1
Base
Upright
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
#
1
1
1
1
6
1
1
2
1
3
2
1
2
2
4
2
1
1
2
1
1
1
1
2
7
1
2
4
2
4
2
4
6
2
2
1
2
2
1
1
3
1
2
1
1
1
1
Console Base
Reed Switch/Wire
Extension Wire
Reed Switch Bracket
Plastic Tie
Reed Switch Clamp
Magnet
Pulse Grip
Resistance Control/Cable
M8 Split Washer
Bumper
Upright Cap
3/4” Axle Cap
Left Pedal Arm
Right Pedal Arm
Incline Frame
Crank Arm
Upper Body Arm
Large Pulley
Frame Bearing
Nylon Spacer
Nylon Washer
Idler Bracket
Pulley
Idler Bearing
3/8” Washer
3/8” x 1” Screw
3/8” Flat Washer
Grip
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
2” x 3” Cap
1” x 2” Cap
3 1/2” Round Cap
Rear Stabiliser
Hook
3/8” Nylon Jam Nut
1/4” Eyebolt
M8 Shoulder Bolt
Adjustment Bracket
M4 x 63.5mm Screw
M5 x 6mm Screw
M5 x 16mm Screw
M6 x 64mm Screw
Levelling Pad
Pedal Bushing
Pedal Wheel
Pedal Wheel Bearing
M8 x 108mm Button Head Bolt
M8 Nylon Locknut
M8 Washer
Chrome Tube Spacer
5/16” x 3/4” Nylon Lock Bolt
Extension Cable
5/8” Axle Cap
Axle
Plastic Handlebar Sleeve
Chrome Tube
Chrome Tube Bushing
Handlebar Bushing
Incline Bracket
M10 x 85mm Bolt
M10 Nylon Locknut
M10 x 105mm Carriage Bolt
Belt
Incline Axle
Axle Screw
Incline Bushing
Incline Frame Cap
M5 x 25mm Screw
Eddy Bracket
M4 x 16mm Screw
Spring
Flywheel
Flywheel Bearing
Flywheel Axle
Pedal Disk
Left Pedal
Right Pedal
M4 x 16mm Flange Screw
Spacer
Wheel
3/8” x 1 3/4” Button Head Screw
Left Side Shield
Right Side Shield
Pulse Wire
Console
Side Shield Support Strip
M6 Nut
Teflon® Lubricant
Side Shield Decal
Warning Decal
#
#
#
#
Grease Packet
Allen Wrench
User’s Manual
#
Note: # indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. HREVEL05983
R0500A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, contact the ICON HEALTH AND FITNESS LTD. office, or write:
ICON HEALTH AND FITNESS LTD.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
Tel: Country Code:
0345-089009
Fax: 0113-2411120
When ordering parts, please be prepared to give the following information:
• The MODELNUMBER OF THE PRODUCT (HREVEL05983)
• The NAME OF THE PRODUCT (HealthRider® E330 elliptical crosstrainer)
• The SERIALNUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) from page 18 of this manual.
HealthRider® is a registered trademark of ICON Health & Fitness, Inc.
Part No. 165052 R0500A
Printed in China © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|