Hayter Mowers Lawn Mower 616E User Manual

Spirit 41  
CODE  
616E  
OWNER’S HANDBOOK  
Original Version (EN)  
ISSUE: 06.06.11  
PART NUMBER: 111-5145 (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Thank you for purchasing a Hayter mower. The following pages are designed to help you  
Use of non standard parts or any arbitrary modifications carried out on this machine may  
gain safe and efficient service from your machine.  
relieve Hayter Limited of liability for any resulting damage or injury.  
IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the mower as it  
gives essential information regarding mower safety, operation, maintenance and specifica-  
tions. Read and understand this handbook prior to operating your mower for the first time.  
Make sure you are familiar with all the controls and points of regular maintenance. If you  
have any doubts, consult your local Hayter authorised dealer who will be pleased to give  
you assistance.  
Hayter mowers are robustly constructed and designed for efficient economical perfor-  
mance under normal mowing conditions. Correct operation and maintenance will ensure a  
long and satisfactory service life. Prior to despatch from our factory every effort is made  
to ensure that your mower is delivered in perfect condition.  
Throughout this handbook all references to left and right are as viewed from behind the  
handlebar, in the direction of forward travel.  
IMPORTANT: This mower is designed solely for use in a domestic grass cutting  
environment. Use in any other way is considered as contrary to the intended use. Compli-  
ance with and strict adherence to the conditions of operation, service and repair as speci-  
fied in this handbook also constitute essential elements of the intended use.  
This mower should be operated, serviced and repaired only by persons who are familiar  
with its particular characteristics and who are acquainted with the relevant safety proce-  
dures.  
This handbook is based on information available at the time of publication.  
HAYTER LIMITED reserve the right to amend product specifications without prior  
notification.  
The safety precautions listed in this handbook and all other generally recognised regula-  
tions on safety must be observed at all times.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS / MAIN FEATURES  
Code  
616  
Engine  
Briggs & Stratton  
Series 500  
2850 rpm  
Unleaded petrol  
1.5 litres  
SAE 30 engine oil  
0.6 litres  
Engine type  
Engine / Cutterbar Speed  
Fuel type  
Fuel capacity  
Oil type  
Oil sump capacity  
Cutting width  
Cutting height  
Overall dimensions  
Weight  
410mm  
13 - 65mm  
1050 x 472 x 1370mm  
30 Kg  
7
1.  
Air Cleaner.  
2.  
Engine Cover  
3.  
4.  
Oil Filler Cap and Dipstick.  
Serial No. Label.  
8
6
5.  
6.  
7.  
8.  
Handlebar Securing Knob.  
Engine Start Grip.  
Engine Stop Lever.  
Upper Handlebar.  
Grassbag.  
5
9
4
3
9.  
2
10.  
11.  
12.  
13.  
Rear Deflector.  
Height Of Cut Adjuster.  
Exhaust Guard.  
1
10  
Spark Plug Lead.  
11  
12  
13  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY PRECAUTIONS  
damaged cutterblade must be replaced immediately with a  
genuine Hayter replacement part.  
Safety Alert Symbol  
Preparation  
This safety alert symbol indicates important safety  
messages. When you see this symbol be alert to the  
possibility of injury. Carefully read the following and  
inform others.  
While mowing, always wear substantial footwear and  
long trousers. Do not operate the equipment when  
barefoot or wearing sandals.  
Operation  
Do not operate the engine in a confined space where  
exhaust fumes (carbon monoxide) can collect.  
Thoroughly inspect the area where the mower is to be  
used and remove all objects which may be thrown by the  
machine.  
Your mower is perfectly safe if used correctly. Failure  
to observe the following precautions may result in  
serious injury.  
Always pull the starter cord slowly until resistance is felt.  
Then pull the cord rapidly to avoid kickback and prevent  
hand or arm injury.  
WARNING: Petrol is highly flammable:  
- store fuel in containers specifically designed for this  
purpose.  
Training  
Mow only in daylight or good artificial light.  
Avoid using the machine on wet grass, where feasible.  
Always be sure of your footing on slopes.  
Walk, never run.  
Before using the mower read the owners handbook  
carefully. Pay particular attention to the safety  
precautions. Ensure that you are familiar with the  
controls and the proper use of the equipment. Learn how  
to stop the mower quickly in an emergency.  
- refuel outdoors only and do not smoke while  
refuelling;  
- add fuel before starting the engine. Never remove the  
cap of the fuel tank or add petrol while the engine is  
running or when the engine is hot;  
- if petrol is spilled, do not attempt to start the engine  
but move the machine away from the area of spillage  
and avoid creating any source of ignition until the  
petrol vapours have dissipated;  
- replace all fuel tank and container caps securely.  
- always use fresh fuel. Stale fuel can block the  
carburettor and cause leakage.  
Never allow children or people unfamiliar with these  
instructions to use the mower. Local regulations can  
restrict the age of the operator.  
Do not mow excessively steep slopes of more than 20O  
and mow across the face of slopes, never up and down.  
Never mow while people, especially children, or pets are  
nearby.  
Exercise extreme caution when changing direction.  
Use extreme caution when reversing or pulling the  
mower towards you.  
Keep in mind that the user is responsible for accidents or  
hazards occurring to other people or their property.  
Replace faulty exhaust.  
A damaged cutterblade or loose fixing bolt are major  
hazards. Before use, always visually inspect the cutting  
mechanism to ensure that it is in good condition. A  
Safety Symbols  
Safety Alert - Be aware  
to the possibility of injury book before using the machine  
Carefully read the Owners Hand-  
Danger of severing  
toes or fingers in  
cutting mechanism.  
Danger of being hit  
by thrown objects.  
Keep bystanders at  
a safe distance from  
the mower.  
Stop engine and remove spark plug  
lead before working on the mower.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY PRECAUTIONS  
while the engine is running.  
Inspect the exhaust periodically and replace if worn or  
leaking.  
Operation cont  
Always replace worn or faulty parts with genuine Hayter  
parts.  
Never touch the exhaust/exhaust guard or cooling fins  
when the engine is hot.  
Never store the mower with petrol in the tank within an  
enclosed area where fumes may reach an open flame or  
spark.  
If the machine has to be tilted for transportation when  
crossing surfaces other than grass, and when transporting  
the machine to and from the area to be mowed. Stop the  
blade (s) by releasing the engine stop lever, ensure that  
the blade (s) have stopped before tilting the mower.  
Stop the engine and disconnect the spark plug lead:  
- Before clearing blockages or unclogging the dis-  
charge chute.  
- Before cleaning/checking or working on the ma-  
chine.  
- After striking a foreign object. Inspect the machine  
for damage and ensure necessary repairs are made  
before re-starting and operating.  
- If the machine starts to vibrate abnormally (check  
immediately).  
Allow the engine to cool before storing in any enclosure.  
To reduce the fire hazard, keep the engine and the  
surrounding deck area free of grass, leaves, or excessive  
grease.  
Never operate the machine with defective guards, or with  
out safety devices, for example deflectors and/or grass  
bag in place.  
Check the rear deflector and grassbag frequently for wear  
or deterioration.  
Do not change the engine governor settings or overspeed  
the engine.  
Stop the engine:  
Replace worn or damaged parts for safety.  
- Whenever you leave the mower.  
- Before refuelling.  
- Reduce throttle setting during engine shutdown.  
Start the engine carefully, with feet well away from the  
cutterblade.  
If the fuel tank has to be drained, this should be done  
outdoors and when the engine is cool.  
Do not tilt the mower when starting the engine.  
Wear strong work gloves when removing and reassem-  
bling the cutterblade.  
Maintenance & Storage  
Do not start the engine when standing in front of the  
discharge chute.  
Keep all nuts, bolts and screws tight to ensure that the  
equipment is in safe operating condition.  
This machine contains spring loaded assemblies which  
could cause a hazard when disassembled and  
reassembled. Maintenance should only be carried out by  
a Hayter authorised dealer.  
Do not put hands or feet near or under rotating parts.  
Frequently check fuel lines and fittings for cracks or  
leaks and replace if necessary.  
Never pick up, carry the machine or lift the rear deflector  
Control Symbols  
STOP  
Engine Stop  
Height of Cut Adjustment  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLING THE MOWER BEFORE FIRST USE  
Delivery Checklist  
Grassbag Attachment  
Fuel Type  
Remove the mower from the packaging and check that  
the following items have been supplied correctly. If any  
items are missing contact, your local Hayter dealer.  
Raise the rear deflector, lower the grassbag through the  
handlebar and hook into position. Lower the deflector to  
rest on the grassbag (Refer fig.4)  
Always use clean, fresh unleaded petrol. Purchase fuel  
in quantities that can be used within 30 days. Never mix  
oil with petrol. For added engine protection Briggs &  
Stratton recommend the use of their fuel additive which  
is available from an authorised Briggs & Stratton service  
dealer.  
1. Engine Handbook.  
3. Parts list/D of C  
Prevent Engine Damage  
2. Grassbag Assembly.  
4. Warranty Reg Card.  
To prevent engine damage the engine is shipped  
without oil or petrol. The engine must be filled with  
the correct grade of oil and petrol before starting the  
engine.  
To prevent accidents cut off the long ribbon attached to  
the grassbag and discard. (Refer fig.1)  
Fill to base of neck to allow for fuel expansion. Do not  
overfill the fuel tank. (Refer fig.7)  
Handlebar  
Oil Type  
Unscrew the handlebar securing knobs sufficiently to  
allow the handlebar to pivot. Move the engine stop lever  
away from the engine to avoid damage and unfold the  
handlebar to the operating position. Make sure the knobs  
are assembled to the outside of the handlebar. (Refer  
fig.2)  
Always use high quality detergent oil classified SAE 30  
oil. Never use additives with recommended oil.  
To prolong the life of your engine it is important that  
the oil is changed after the first 5 hours of use - Refer to  
‘Maintenance Schedule’.  
Tighten both handlebar knobs to secure in position.  
Check Oil Level  
Clean around the oil filler cap before removing. With  
the mower on a level surface, unscrew and remove the  
oil filler - dipstick. Wipe oil from it with a clean cloth.  
Screw the oil filler - dipstick back in place, then unscrew  
and remove it to check the oil level. (Refer fig.6)  
Take care to ensure that the control cables do not  
become snagged at the pivot point.  
Grassbag Assembly  
Insert the metal frame into the grassbag fabric and then  
clip into position. (Refer fig.3)  
The oil level is correct when it is at the full mark on the  
dipstick. DO NOT OVERFILL. (Refer fig.6)  
Fig. 6  
Fig. 7  
Fig. 1  
Fig. 2  
Fig. 3  
Fig. 4  
Fig. 5  
2
0.15  
Litres  
1
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING THE MOWER  
handlebar to start and keep the engine running. If the  
engine stop lever is released the engine will stop.  
Emergency stop: Release the engine stop lever.  
Controls  
Operate all control levers several times and ensure that  
the cables move freely. Check that the engine stop lever  
returns freely to its rest position when released. (Refer  
fig.8)  
If the engine fails to stop, disconnect the spark plug  
lead. (Refer fig.12)  
To prevent damage never pull the engine start grip  
when the engine is running.  
Forward Travel  
Starting - Step 1  
Hold and push against the handlebar with both hands to  
move the mower forwards. (Refer fig.11)  
Operate the primer bulb.  
Push on the primer bulb 5 times at two second intervals  
to provide the extra fuel to start the engine after  
assembling the mower for the first time.  
Reverse Travel  
Hold and pull against the handlebar with both hands to  
reverse the mower.  
In normal use push on the primer bulb 3 times at 2  
second intervals to provide extra fuel required to to start  
a cold engine. Operation of the primer bulb is usually  
unnecessary when starting a warm engine. (Refer fig.9)  
Turning  
To make a wide turn steer the mower with the handlebar  
in the direction required.  
Starting - Step 2  
To make a tight turn, apply downward pressure on the  
handlebar to raise the front wheels just above ground  
level and steer in the required direction.  
Stand behind the mower and hold the handlebar together  
with the engine stop lever with your left hand. With your  
right hand hold the engine start grip and pull slowly until  
resistance is felt, then pull rapidly to crank the engine.  
Carefully return the start grip to the storage position  
when the engine starts.  
To prevent accidents do not raise the front of the  
mower excessively when making a turn. Never raise  
the rear of the mower when the engine is running.  
If the engine does not start after 5 attempts, refer to  
‘Trouble Shooting’. (Refer fig.10)  
Stopping  
Release the engine stop lever.  
The engine stop lever must be held firmly against the  
Fig. 12  
Fig. 9  
Fig. 8  
Fig. 10  
Fig. 11  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING THE MOWER  
Slopes  
Grassbag  
Friction Disc  
To prevent engine damage do not use the mower on  
slopes greater than 20 degrees. (Refer fig.13)  
Raise the rear deflector and lift the grassbag through the  
handlebar and lower the rear deflector to rest against the  
rear of the mower.  
The cutterblade is driven by the engine via a friction  
disc to help prevent damage occurring to the engine  
crankshaft and cutting mechanism when a hidden  
obstruction or overload is encountered. (Refer fig.19)  
Height Of Cut  
To empty the grassbag, pour out the grass clippings and  
shake the grassbag vigorously to clean the airways. Good  
grass collection depends on good air flow through the  
grassbag. When collecting grass clippings it is important  
that the grassbag is emptied regularly to prevent block-  
ages and engine overloading. (Refer fig.16)  
To adjust the height of cut: Grip the lever and pull side-  
ways to disengage it from the locking notch, then push  
forwards to lower or pull backwards to raise the height  
of cut. Finally release the lever at the required position  
and ensure it locks firmly into one of the seven setting  
notches.  
Always stop the engine when a hidden obstruction  
or excessive vibration is encountered. Disconnect the  
spark plug lead and examine the cutting mechanism.  
ALWAYS replace a damaged cutterblade - Refer to  
“Maintenance”.  
Always select a height of cut to suit operating conditions.  
Aim to prevent engine overloading and blockages by  
avoiding low cuts in long grass conditions. Be prepared  
to make two cuts when the grass is long. (Refer fig.14)  
Without Grass Collection  
Remove the grassbag and operate the mower with the  
rear deflector in the closed position. (Refer fig.17)  
Non Grassed Areas  
When moving the mower across non-grassed areas, stop  
the engine and set the mower to the maximum height of  
cut to protect the cutting mechanism. (Refer fig.14)  
Heavy Growth  
Before Mowing  
Areas of heavy growth should be mown without  
collecting the clippings. If collection is required, first  
mow the area without the grassbag at the maximum  
height of cut setting. Allow the grass clippings to dry  
out and then mow the area at the maximum height of cut  
setting with the grassbag fitted. Reduce the height of cut  
and mow the area again as necessary until the required  
finish is obtained.  
To prevent accidents, thoroughly inspect the area  
and remove all objects which when contacted by the  
mower cutterblade could become dangerous projec-  
tiles. Inspect the area for hidden obstructions which  
when contacted by the cutterblade could risk health  
and safety or result in damage to the mower. Remem-  
ber the location of these obstructions and ensure that  
you mow around them. (Refer fig.15)  
To prevent damage to your lawn do not remove more  
than one third of grass height in one cut. (Refer fig.18)  
Fig. 15  
Fig. 16  
Fig. 17  
Fig. 13  
Fig. 14  
Fig. 18  
Fig. 19  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE SCHEDULE  
heavy load or high ambient temperature.  
Maintenance Schedule  
To prevent accidents, stop the engine and disconnect  
the spark plug lead before attempting to carry out  
procedures on the mower.  
- Service the air cleaner.  
- Lubricate wheels, pivot points and linkages and grease  
the inner control cables at point of entry and exit from  
their outer casing.  
After the very first five hours change the engine oil.  
Follow the hourly or calendar intervals, whichever occurs  
first. More frequent service will be required if working for  
prolonged periods under dusty, dry conditions, or when  
airborne debris is present or after extensive operation  
cutting tall, dry grass.  
- Check the clutch cable adjustment.  
- Sharpen the cutterblade.  
50 Hours Or Every Season  
Change the engine oil.  
Daily  
- Check the oil level.  
100 Hours Or Every Season  
- Clean the engine cooling system. Clean more often  
under dusty conditions or when airborne debris is  
present or after prolonged operation whilst cutting tall,  
dry grass.  
- Remove grass debris from around the engine, exhaust/  
exhaust guard, air ways in the top cowl, underside of  
the deck housing and from the grassbag and check for  
signs of damage.  
- Replace the spark plug.  
- Check the condition of guards and safety devices.  
- Check condition of cutterblade.  
Engine Detail (Refer fig.20)  
25 Hours Or Every Season  
- Change the engine oil if continuously operating under  
Fig. 20  
1. Air Cleaner  
2. Primer Bulb  
3. Fuel Cap  
6
5
4
4. Start Grip  
7
5. Cover  
6. Oil fill/Dipstick  
7. Exhaust Guard  
8. Spark Plug / Lead  
8
3
1
2
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOWER MAINTENANCE  
Carburettor Adjustments  
Air Cleaner Service  
Keeping Engine Clean  
Should only be made by an authorised Briggs & Stratton  
dealer. Under no circumstances should the engine be  
adjusted to run at a speed in excess of that shown on the  
Declaration of Conformity.  
To service the air cleaner, loosen and remove screw (1)  
Remove all grass and debris from the engine including  
the exhaust/exhaust guard, the air ways in the top cowl  
and the surrounding deck areas on a daily basis after  
use. Never spray the engine with water during cleaning.  
Water can contaminate the fuel. Always clean with a  
brush or compressed air. (Refer fig.25)  
and remove cover (2). (Refer fig.22)  
Remove the foam element (3) and wash in a solution  
of liquid detergent and water. Allow to dry thoroughly  
before fitting or wrap in a cloth and squeeze dry. If very  
dirty, replace.  
Oil Service  
Check the oil level daily before starting the engine and  
ensure that the correct oil level is maintained. Refer to  
‘Before Starting the Mower’ for oil checking and filling  
instructions.  
- Do not use petroleum solvents.  
- Do not use pressurised air.  
- Do not oil the cartridge.  
Grass and debris may clog the engine’s air cooling  
system especially after prolonged operation while cutting  
tall, dry grass. The internal cooling fins and surfaces  
may require cleaning to prevent overheating and engine  
damage. We recommended that this service be carried  
out by an authorised Briggs and Stratton dealer.  
Saturate with clean oil and squeeze out excess.  
Change the engine oil after the first 5 hours of operation  
and thereafter according to the ‘Maintenance Schedule’:-  
After servicing, re-assemble the air cleaner and fasten  
securely.  
1. Drain fuel by running the engine until the fuel tank is  
empty.  
2. Remove the spark plug lead.  
Grassbag  
Remove grass debris from the grassbag immediately  
after use and check its condition for signs of damage.  
To prevent accidents replace a damaged grassbag  
immediately. (Refer fig.26)  
Spark Plug Service  
Use only Briggs & Stratton (Part number 19368) spark  
tester (1) to check for a spark as shown in the diagram.  
(Refer fig.23)  
3. Allow the engine to cool.  
4. Drain the oil while the engine is warm (not hot)  
5. Tip the mower over on to its left hand side thus  
ensuring that the air cleaner is kept uppermost to  
prevent engine damage.  
6. Remove the oil filler dipstick and drain the oil into a  
suitable container.  
7. Refill with new oil of the recommended SAE  
viscosity grade. (Refer to-‘Before Starting the  
Mower’) (Refer fig.21)  
Deck Housing  
Replace the spark plug every 100 hours or every season,  
whichever occurs first. A spark plug wrench is available  
from any authorised Briggs & Stratton service dealer.  
Remove grass debris from the top and underside of the  
deck housing immediately after use. (Refer fig.27)  
Fertilisers and top dressings are particularly  
corrosive. Thoroughly clean the mower deck  
immediately after use on treated grass and store well  
away from corrosive materials.  
Check the spark plug gap with a feeler gauge and set at  
0.76mm. (Refer fig.24)  
Fig. 21  
Fig. 22  
Fig. 23  
Fig. 24  
Fig. 25  
Fig. 26  
Fig. 27  
1
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOWER MAINTENANCE  
edges to avoid the risk of injury should the tool slip.  
ALWAYS use genuine Hayter replacement parts.  
A slightly worn cutterblade may be re-sharpened. Both  
blade edges must be sharpened equally to ensure balance.  
Sharpen the cutterblade every 25 mowing hours or more  
frequently if conditions require. Remove the cutterblade  
from the mower and clean using a brush and water. In-  
spect the cutterblade for signs of damage.  
Securing Nuts & Bolts  
Regularly check that all securing nuts and bolts are tight.  
Replace missing or damaged items immediately.  
The condition of the cutterblade and its mounting  
arrangement should be checked regularly for signs of  
wear or damage. Ensure that the cutterblade is not bent  
or cracked.  
Lubrication  
Lubricate the wheels, pivot points and linkages with  
engine oil every 25 operating hours.  
Sharpen both cutting edges with a flat file to restore per-  
formance. (Refer fig.30)  
A damaged cutterblade that is out of balance will vibrate  
excessively and may break. DO NOT use an unbalanced  
cutterblade.  
Apply a good quality medium grease to the inner control  
cables at the point of entry and exit from their outer cas-  
ing.  
Ensure that the cutterblade is balanced. Use a screw driv-  
er with a round shaft to support the cutterblade through  
its centre hole. Hold the cutterblade horizontal and then  
release. A balanced cutterblade will remain horizontal.  
(Refer fig.31)  
Regularly check that the bolt securing the cutterblade is  
tightened to the specified torque of 54Nm.  
Cutterblade Removal  
Drain the fuel by running the engine until the fuel tank  
is empty and the engine stops. Remove the spark plug  
lead and allow the engine to cool. Turn the mower on its  
left hand side and ensure that the air cleaner side of the  
engine is uppermost. (Refer fig.28)  
Replace the cutterblade every 2 years of sooner if  
excessively worn or damaged.  
If the cutterblade is not balanced the heavy end will  
rotate downwards. Sharpen the heavy end until the  
cutterblade is correctly balanced. (Refer fig.32)  
To prevent injury it is wise to seek assistance when  
turning the mower on its side.  
Firmly grip the end of the cutterblade with a gloved hand  
and remove the bolt, spring washer and distance piece  
securing the cutterblade with a 9/16” A/F spanner. (Refer  
fig.29)  
Cutterblade Assembly  
Assemble the cutterblade with the turned up edges facing  
towards the engine. Secure the cutterblade using the bolt  
(1), spring washer (2), distance piece (3) and tighten to a  
torque of 54Nm. (Refer fig.29)  
To prevent accidents never work on the cutterblade  
unless the spark plug lead has been removed. The  
cutterblade has sharp edges. ALWAYS wear strong  
gloves to protect your hands when working on the  
cutterblade. DO NOT rotate tools towards the cutting  
Cutterblade Sharpening  
Fig. 28  
Fig. 29  
Fig. 30  
Fig. 31  
Fig. 32  
30-45  
3
2
1
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOWER MAINTENANCE  
Slowly pull the engine start grip once to crank the engine.  
This will distribute the oil and help prevent engine corro-  
sion.  
Storage  
To store the handlebar, unscrew the 2 small securing  
knobs sufficiently to allow it to be pivoted forwards to  
rest against the mower. Take care to ensure that the con-  
trol cables do not become snagged at the pivot point and  
depress the engine stop lever to prevent it being dam-  
aged through contact with the engine spark plug. (Refer  
fig.33)  
Clean grass and debris from the engine cylinder, cylinder  
head cooling fins, under top cowl, around and behind ex-  
haust/exhaust guard and ensure that the grassbag is clean.  
Lubricate the mower and treat metal parts with a water  
repellent anti-corrosion product.  
Engines stored in excess of 30 days need to be protected  
with Briggs & Stratton fuel additive or drained of fuel to  
prevent gum from forming in the fuel system or on essen-  
tial carburettor parts. To ensure your mower is maintained  
in good working order it is important that the following  
procedure is adopted. Refer to the Maintenance section  
as necessary.  
Cover the mower with a protective sheet and store it in a  
dry, ventilated area.  
Drain fuel from the engine by operating the engine until  
it stops.  
Disconnect the spark plug lead.  
Change the engine oil.  
Remove the engine spark plug and pour 15ml of engine  
oil into the engine cylinder and replace the spark plug. Do  
not exceed the stated volume of oil as engine damage may  
occur on re-starting. Do not replace the spark plug lead.  
Fig. 33  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LAWN CARE CALENDAR  
To be used as a guide only  
January  
June  
October  
There is very little work to do this month apart from  
brushing away leaves. Keep off the grass if frozen or  
waterlogged.  
Summer mowing should now be under way. It should be  
necessary to mow the lawn twice a week. Raking before  
mowing is important this month as the combined action  
keeps runners of clover under control. Water the grass if  
necessary, and remember to soak thoroughly.  
Rake out the thatch from the turf and spike the lawn to  
assist in drainage. Brush in peat and sharp sand.  
November  
February  
Use a stiff broom to disperse worm casts before mowing.  
Rake the grass thoroughly. Spike the lawn to aerate and  
stimulate soil organisms and root growth and apply lawn  
sand if necessary.  
Keep turf free from leaves.  
July  
Treat the grass with the second application of fertiliser  
or weed killer/fertiliser. Water when necessary and rake  
occasionally. As a general rule the grass clippings should  
be removed each time you mow. If weather conditions  
are dry and hot and the grass is weed free, leave the  
clippings on the lawn to help maintain ground moisture.  
December  
Apart from brushing away leaves, December is a slack  
end of a busy year. Keep off the lawn if it is very wet or  
frozen.  
March  
The yearly lawn work programme really starts this  
month. As soon as the ground conditions are suitable,  
the first cut can be made. The first cut should merely  
“top” the grass as close cutting at this stage could result  
in severe yellowing or browning. Two cuts are generally  
sufficient this month.  
Lawn Stripes  
The way to achieve a neat striped effect is for the lawn  
being cut in parallel stripes, alternate stripes being mown  
in opposite directions. A much more important routine is  
to cut at right angles to the line of the previous mowing.  
If the work has been carried in a north-south line, then  
the next cutting should be in an east-west direction. The  
cross-cutting keeps down the coarse weed grasses.  
August  
Keep mowing regularly and watering as necessary. Fill  
any cracks caused by drought with a mixture of sharp  
sand and soil. In dry weather conditions leave the grass  
longer to help retain ground moisture.  
April  
Mow often enough to stop grass growing away. Dig out  
patches of coarse grass or resistant weed. Re-seed bare  
patches.  
September  
Raise the height of cut to allow the grass to thicken and  
protect the roots from the winter frost and snow.  
To prevent grass damage do not remove more than  
one third of the grass height in one cut.  
May  
Keep mowing increasing the frequency as required.  
Treat with selective weed killers or combined weed/feed  
preparations if you did not feed the lawn in April.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING  
PROBLEM  
CAUSES  
CORRECTIVE ACTION  
PROBLEM  
CAUSES  
CORRECTIVE ACTION  
1. Engine stop lever released  
2. Incorrect oil level  
3. Obstruction under deck  
4. Battery discharged (if fitted)  
1. Operate engine stop lever  
2. Check oil level  
3. Remove obstruction  
4. Charge battery  
Discharge chute blocks 1. Grass is wet  
1. Mow dry grass  
2. Cut height is too low  
3. Grassbag full  
4. Airflow through the grassbag  
is restricted  
2. Increase cut height  
3. Empty grassbag  
4. Clean the grassbag  
Engine will not turn  
over  
1. Excess oil  
2. Air cleaner cartridge oil  
soaked or blocked  
1. Check oil level  
2. Service air cleaner  
Mower is hard to push 1. Cut height too low  
1. Increase cut height  
2. Inspect and replace as neces-  
sary  
2. Wheels/roller damaged  
Engine smokes  
Poor grass collection  
1. Airflow through the grassbag  
is restricted  
2. Discharge chute blocked  
3. Wet grass  
1. Clean the grassbag  
1. Fuel starvation  
2. Fuel cap vent blocked  
1. Fill fuel tank  
2. Clean fuel cap vent  
Engine runs then stops  
2. Remove blockage  
3. Mow in dryer conditions  
4. Empty grassbag  
1. Engine under load  
2. Incorrect/contaminated fuel  
1. Raise height of cut  
2. Drain tank and fill with correct  
fuel  
4. Grassbag full  
Cutterblade drive will 1. Engine stop lever not fully  
not engage/disengage forward  
1. Push fully forward disengage  
3. Spark plug lead disconnected 3. Connect spark plug lead  
Engine will not start  
4. Engine brake not released  
5. Faulty spark plug  
4. Operate engine brake lever  
5. Clean and adjust the gap or  
replace  
6. Battery discharged (if fitted)  
6. Charge battery  
7. Wiring fault  
7. Check wiring  
1. Spark plug lead becoming  
disconnected in use  
1. Connect spark plug lead  
2. Faulty spark plug  
3. Air cleaner blocked  
4. Incorrect/contaminated fuel  
2. Clean and adjust gap or replace  
3. Service air cleaner  
4. Drain tank and fill with correct  
fuel  
Engine runs rough  
1. Mounting bolt loose  
1. Tighten bolts  
Engine vibrates exces- 2. Cutterblade bolt loose  
2. Tighten bolt  
sively  
3. Cutterblade out of balance  
4. Bent Crankshaft  
3. Balance cutterblade  
4. Consult your dealer  
1. Undulating ground conditions 1. Change direction of travel  
2. Cutterblade worn  
3. Cutterblade out of balance  
4. Wheels/roller damaged  
2. Sharpen cutterblade  
3. Balance the cutterblade  
4. Insect & replace as necessary  
Uneven cut  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
NOTES  
Hayter Limited warrants to the original user/purchaser that this unit shall be free from  
defects in material and workmanship under normal use and service for a period of three  
years from the date of purchase. The manufacturer of major proprietry components ie.  
engines, gearbox / transaxle (where applicable) furnish their own warranty and services  
are provided through their authorised network. To qualify for the full benefit of the  
warranty, the warranty registration card must be returned within 14 days of purchase.  
Subject to the conditions and exclusions noted in this limited warranty, we shall at our  
option, repair or replace any warranted part during the applicable period. If you are in  
doubt or experience any difficulty, please consult a Hayter Authorised Service Dealer  
for clarification.  
To qualify for the extended warranty (second and third year) of the three year limited  
warranty the machine must have annual services carried out by an Authorised Hayter  
Service Dealer. These chargeable services should be carried out within 12 and 24  
months of the date of purchase.  
Excluded from the extended warranty period are those items which are subject to  
normal wear and tear e.g. tyres, wheels, cutterblades, belts, cables, grassbags,  
sweeper/brushes, batteries and other consumable wearing parts.  
All consumer machines which are fitted with a genuine Hayter friction disc as original  
equipment before use, are covered by a Lifetime Warranty against the engine  
crankshaft bending. Note: friction washers, blade brake clutch (B.B.C) units and other  
such devices are not applicable. Only machines fitted with a genuine Hayter friction  
disc, which are used in accordance with the recommended operating and maintenance  
procedures, are covered.  
This warranty does not apply to any unit that has been tampered with, altered, misused,  
abused or used for hire, and will become invalid if non genuine Hayter parts are fitted.  
This warranty does not cover minor mechanical adjustments unless they are due to  
defective material or workmanship. Consult the Owner's Handbook or a Hayter  
Authorised Service Dealer for assistance when making these adjustments.  
A warranty period of 90 days applies to machines used for commercial purposes.  
To make a warranty claim, return the unit to a Hayter authorised dealer along with  
proof of purchase stating the machine serial number and date of purchase. The service  
receipt(s) or this Owners Handbook with the 1st/2nd year service boxes fully  
completed, must be produced as proof of entitlement to the extended warranty period.  
Subject to the conditions and exclusions in this limited warranty, the authorised dealer  
will, at our option, repair or replace any warranted part within the duration of the  
warranty period.  
This limited warranty gives you specific legal rights and is in addition to any statutory  
rights to which you may be entitled and your statutory rights are not affected by this  
warranty. If you need additional information concerning this written warranty, or  
assistance in obtaining services, please write to : HAYTER LIMITED, Service  
Department, Spellbrook, Bishop's Stortford, Hertfordshire CM23 4BU  
UK ONLY: Details of your local Hayter authorised dealer are contained in Yellow  
616298.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
NOTES  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUSTOMER INFORMATION  
SERVICE RECORD  
CODE  
SERIAL NO.  
1st Year (12 months)  
1st Year (12 months)  
Owner’s Name:  
Serial Number:  
We certify that this service has been  
carried out by an Authorised Hayter  
Service Dealer  
Date:  
Date:  
Engine Type:-  
Date of Sale:-  
Engine:-  
Your Local Dealer:-  
Note for dealer: Please retain this voucher for your records.  
2nd Year (24 months)  
2nd Year (24 months)  
Owner’s Name:  
Serial Number:  
We certify that this service has been  
carried out by an Authorised Hayter  
Service Dealer  
Date:  
Date:  
Note for dealer: Please retain this voucher for your records.  
Hayter Limited, Spellbrook, Bishop’s Stortford, Herts, CM23 4BU, England  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Inc Paint Sprayer 233710 User Manual
Graco Microscope Magnifier 24B771 User Manual
Grundig Blu ray Player GBP 7000 3D User Manual
Haier Washer HW60 1201S U User Manual
Hans Grohe Plumbing Product 06490XX0 User Manual
Harbor Freight Tools Welding System 93096 User Manual
Hayter Mowers Lawn Mower CODE144S User Manual
Heatiator Indoor Fireplace BH42A User Manual
Hotpoint Convection Oven SH83CX S User Manual
Hypertec Camera Accessories D7968PHY User Manual