Installation & Operating manual
The harman TlC 2000 Coal/wood Stove
R11
SAFETY NOTICE
PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE YOu INSTAll ANd uSE YOur NEw rOOm hEATEr. FAIlurE
TO FOllOw INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh.
FOr uSE IN ThE u.S. ANd CANAdA. dO NOT INSTAll IN A mObIlE hOmE.
IF ThIS STOvE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOllOw
INSTAllATION dIrECTIONS.
CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION
rEQuIrEmENTS IN YOur ArEA.
CONTACT YOur lOCAlAuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE
PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.
CETTE guIdE d'uTIlISATION EST dISPONIblE EN FrANCAIS. ChEz vOTrE CONCESSIONNAIrE dE
hArmAN.
manual # 3-90-08691
SAvE ThESE INSTruCTIONS.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
4
INDEX
Specifications
6
Operation
8
Building a Fire
Maintenance
Installation
9
13
15
17
20
23
Chimney System
Service Parts List
Warranty
Please read this entire manual before you install and use your new
room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
DO NOT INSTALL IN A MOBILE HOME.
SAVE THESE INSTRUCTIONS
Harman™
352 Mountain House Road
Halifax, PA 17032
U.S.A.
Appliance Certification.
model: TLC-2000
listed by: OMNI-Test Laboratories
Report #: 135-S-28-4
Type: Solid Fuel Burning Room Heater
Standard(s): UL 1482, UL 737, ULC-S627
Note: This appliance is also approved for
installation into a shop.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
5
WARNINGS
Carbon Monoxide (CO) Awareness
Carbon monoxide, referred to as CO, is a color-
CO detectors are very sensitive and may
sound an alarm for fumes other than CO or CO
from sources other than the stove such as car or
lawn mower exhaust.
less, odorless gas that is produced during combustion
of coal and other fuels. CO fumes are toxic and can
be fatal.
The TLC 2000 is a natural draft system which
relies on a properly designed chimney to remove CO
and other combustion by-products from the stove.
Even though this stove is designed to be as safe
as possible, it is important that you install a CO detec-
tor. This is true for oil, gas, or wood as well.
CO is not specifically heavier or lighter than
air. Therefore, it is best to install the detector at table
top level rather than on the ceiling like a smoke de-
tector.
If the alarm sounds
1. Increase ventilation by opening windows or
doors.
2. Make sure the stove doors are closed and
latched.
3. Check stove for normal operation.
4. Check for false alarm.
5. Have all occupants exit the building until
the cause for the alarm is discovered and/or
remedied.
(Never sleep in the same room with any coal burning stove.)
NEvERuSEGASOLINE,GASOLINE-TyPELANTERN
FuEL, kEROSENE, CHARCOAL LIGHTER FLuID,
OR SIMILAR LIquIDS TO START OR “FRESHEN
uP” A FIRE IN THIS HEATER. kEEP ALL SuCH
LIquIDS WELLAWAy FROM THE HEATER WHILE
IT IS IN uSE.
DO NOT CONNECT TO ANy AIR DISTRIBuTION
DuCT OR SySTEM.
DO NOT uSE CHEMICALS OR FLuIDS TO START
THE FIRE.
DO NOT INSTALLA FLuE DAMPER IN THE
EXHAuST vENTING SySTEM OF THIS
APPLIANCE.
DO NOT BuRN GARBAGE OR FLAMMABLE
FLuIDS SuCH AS GASOLINE, NAPTHA, OR
ENGINE OIL
DO NOT CONNECT THIS uNIT TO A CHIMNEy
FLuE SERvING ANOTHER APPLIANCE
HOT WHILE IN OPERATION. kEEP CHILDREN,
CLOTHING AND FuRNITuRE AWAy. CONTACT
MAy CAuSE SkIN BuRNS.
INSTALL vENT AT CLEARANCES SPECIFIED By
THE vENT MANuFACTuRER.
WHEN INSTALLING IN A TIGHTLy
CONSTRuCTED HOME, A SOuRCE OF FRESH
AIR TO THE ROOM MAy BE NECESSARy FOR
PROPER OPERATION OF THIS APPLIANCE.
CAuTION: FAILuRE TO FOLLOW THE
INSTALLATION INSTRuCTIONS IN THIS MANuAL,
OR uSING MAkESHIFT COMPROMISES DuRING
INSTALLATION MAy RESuLT IN PROPERTy
DAMAGE, PERSONAL INjuRy OR EvEN DEATH.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
6
Specifications - TLC 2000
Weight
Flue Size
Fuel
375 lbs
6 inch
USA: Pea, Nut, or Stove coal
Cordwood with optional spark screen
Canada: Wood, or coal as above. Wood alone as local
codes allow
Log Length Recommended
Heating Capacity
16" with 18" Max
1,900 sq. ft.
Blower Size (optional)
135 cfm. variable speed
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
7
Top Load Door
Clean-out Cover
Top Load Opening
Top Load
Door Arm
Glass Door
Wood Air
Control
Grates (2)
Coal Bars (3)
Side Shield
Coal Air Control
Removable
Shaker Handle
Front Load
Door Latch
Ash Door
Ash Door Latch
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
8
Operation
Fuels for uSA
The Stove
Coal:
Doors
Anthracite coal, pea or nut size, is the primary fuel for
which the TLC2000 is designed. Bituminous coal may also
be burned but the results will vary due to the variation in
bituminous coal from region to region.
Your stove has a large glass-paneled door for loading and
fire viewing, a separate smaller door for removing ashes and
a top loading door. To open the glass door, turn the handle
clockwise and pull out; to close the door, return the handle
to an open 9 o'clock position and push in to engage the latch
while turning the handle counterclockwise to the 6 o'clock
position. To open the ash door, lift up on the handle and pull
out. Close the door by pushing in and pushing the handle all
the way down. To open the top load door move the wooden
knob located on the left side of the stove front and upward
until it locks the top open.
Wood:
Wood may be burned in the TLC2000 for the purpose of
igniting coal.
Wood may also be burned with the glass door open and a
screen in place to prevent sparks from escaping. This provides
a real open fire atmosphere.
All doors must be closed while the stove is in normal opera-
tion, and the gaskets routinely examined for wear and replaced
when necessary. The glass door may be left open and the
opening covered with a screen when operating as a fireplace.
Good door seals are important for maintaining control of the
stove. Operating the stove with the ash door open, or with a
door inadequately sealed, could create a serious overfiring
condition (discussed later in this section).
Fuels for Canada
Wood:
Wood may be burned as a primary fuel, providing that your
local and provincial codes allow it.
Wood may also be burned with the glass door open and a
screen in place to prevent sparks from escaping.
Coal:
Anthracite coal, pea or nut size, may also be burned as a
primary fuel for the TLC2000. Bituminous coal may also be
burned but the results will vary due to the variation in bitu-
minous coal from region to region.
NEvER OPERATE WITH MORE THAN ONE DOOR
OPEN AT A TIME
The glass used in your TLC 2000 is manufactured to exact
standards to withstand the high heat of the fire, but like all
glass, it must be treated with common sense and care. Never
abuse the glass by slamming the door shut or striking the
glass with a heavy object. If the glass is broken or damaged,
do not operate the stove until it has been replaced. The coal
bars must be installed to protect the glass. Never build a fire
directly against the glass.
Fuel should be stored in a dry place, prefferably indoors.
Keep fuel outside the installation clearance area. Also, keep
fuel away from all maintenance access areas.
CAuTION: uSE OF FuELS OTHER THAN THOSE
SPECIFIED WILLvOID THE PRODuCTWARRANTy
AND MAy POSE A RISk TO PERSONAL HEALTH
AND SAFETy.
Grates
The TLC 2000’s unique grate system consists of two Cast
iron grates linked together to operate simultaneously when
the external shaker handle is moved.
The purpose of the grate system is to support the coal bed
while air flows up through the grates to the burning coal. The
grates are also used to remove ashes from the bottom of the
coal bed while the fire is burning. This is accomplished by
shaking the shaker lever back and forth with short choppy
strokes. This causes the ashes to fall through the grates into
the ash pan. It is the special design of the Harman Grates
that allows longer intervals between refueling and shaking
the grates.
REMOvAL OR MODIFICATION OF THIS GRATE
SySTEM MAy CAuSE A DANGEROuS SITuATION.
Harman TLC 2000 Grate System
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
9
Air Controls
Coal
CAuTION: THE OPERATION RANGE OF
THE AIR CONTROLS MAy NOT BE ALTERED
FOR ANy REASON.
The primary air control for coal burning is a knob
located on the bottom door. Sliding the knob to the left pro-
vides less air for a smaller fire. Sliding the knob to the right
provides more air for a larger fire. When burning wood, this
knob should be all the way to the left, closed.
Wood
The primary air controls for wood burning are located
on each side as shown at left and on page 6. Both controls
should be adjusted equally. Air from these controls also pro-
vides a curtain of air across the glass to keep it clean. Move
the controls down for less heat and up for more heat. When
burning coal these controls should be in the down position.
CAuTION: The wood controls are hot. use the removable
shaker handle or gloves to adjust these controls.
Coal must have air coming up through the coal bed in order
to burn. Some air over the top of the coal helps burn gases. A
small amount of air enters the top of the coal fire when the
wood controls are in the down position.
WOOD
WOOD
COAL
Wood burns with top or bottom air; however, top air com-
ing down across the glass to form an air curtain works best
and keeps the glass clean.
This is why it is recommended that the coal control be
positioned to the left for wood burning.
Building and
Maintaining a Wood Fire
Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or “freshen
up” a fire in this heater. keep all such liquids well away
from the heater while it is in use
Crumple up six to eight sheets of news paper and place
in the firebox. Next place pieces of dry wood 3/4 inch maxi-
mum diameter on top of the paper, Next place several 1"-2"
split pieces of dry wood on top, followed by a few 2"-3" split
pieces. Set the wood air controls at the maximum heat output
setting, all the way up. Place the knob on the bottom door to
the left. These settings will allow the glass to stay clean as
you build your fire. The coal knob may be moved to the right
to speed the ignition process but the glass may get dirty.
Ignite the paper and allow the fire to burn until a good
charcoal bed, 2"- 3" (50 mm - 80 mm) is formed; (You may
need to leave the ash door open a crack to get the blaze going
properly, but never leave the stove unattended with a door
open.) Add more wood to create a deeper charcoal base 3"
to 4".
CAuTION: ALWAyS WEAR FIRE-
RESISTANT GLOvES TO OPERATE THE
STOvE. THE AIR CONTROL IS HOT
WHILE IN OPERATION.
Once the charcoal bed is established you may add a full
load of dry wood. After adding the fuel, leave air setting at
maximum for 5 to 15 minutes. Then, adjust the air controls
and blower speed for the desired heat output.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
10
Reloading.
Remove
Once you have prepared and maintained a thick charcoal
bed, you should be able to reload the stove, allow some burn-
ing at the maximum air setting, and reset the air control in a
few minutes.
Cleanout Plate
To Burn As A
Fireplace Stove
Select hardwoods if possible, as they are heavier and
contain more heating capacity (BTU’s) per load than do
softwoods. Wood should be split and stored under cover for
“seasoning” - a year is recommended. Your stove is not an
incinerator - do not burn garbage, painted or treated wood,
plastic, or other debris.
Keep the area around the stove free from clutter. Keep all
combustibles, including fuel, beyond the code-required clear-
ance distance (48" or 1215 mm in the U.S., 1525 mm or 60" in
Canada). Never store fuel in front of the stove where it could
interfere with door operation, safe loading, and ash removal.
Blower. To regulate the speed of the optional convection
blower, adjust the control from low to high by turning the
knob located on the blower cord.
Removing Wood Ashes.
Always wear gloves to remove the ash pan. Lift the latch
on the ash door and open. Pull the ash pan out by the handle.
Lift the handle to the vertical position to carry the ashes to a
disposal location. Close the ash door while you are disposing
Ashes should be placed in a steel container with a tight of the ashes. The fire will get very hot if the bottom door is
fitting lid and moved outdoors immediately. The closed left open even for a short period. Replace the ash pan. Re-
container of ashes should be placed on a noncombustible move ashes from the fire chamber periodically by shaking
floor or on the ground, well away from all combustible the grates. Wood burns best with an ash bed under the wood;
materials, pending final disposal. If the ashes are disposed therefore, do not shake all of the ashes down. Never let the
of by burial in soil or otherwise locally dispersed, they ashes build up to over 3" in depth. Excessive ash buildup can
should be retained in the closed container until all cinders prevent proper venting of exhaust gases. Also do not overfill
have thoroughly cooled. Other waste shall not be placed the ash pan. Ash buildup between the ash pan and the grates
in this container.
can cause them to overheat and wear out prematurely.
Operating as a Fireplace
The TLC 2000 is tested and approved to be burned with
the front load door open. In this mode of operation you get a
true fire sound as well as appearance. Due to the crackling and
popping of burning wood it is necessary to place the optional
screen over the door opening. This prevents sparks from enter-
ing the room just like a screen over a fireplace.
The clean-out plate (see above) should be removed to
burn as a fireplace. This is done by lifting up on the tab on
the front of the plate.
To install the screen, open the glass door and place the
screen over the door opening. Push on the screen until the
two spring clips snap into place. To remove the screen, pull
on the handle.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
11
Building and Maintaining a Coal Fire;
Build a wood fire as described but instead of adding larger
wood, limit the size to about 2" in diameter. Add enough 2"
wood that the firebox floor is covered with burning wood.
After the wood is burning well for about five minutes, put
the wood air controls in the down position and slide the coal
air control to the right. This makes the primary air flow up
through the grates as is required for coal burning.
Next add a layer of coal on top of the wood. Continue
burning until the layer of coal is turning red and igniting. It
is possible to speed this process by opening the ash door, but
never for more than five minutes at a time.
Operation with the ash door open for more than five min-
utes will overfire the stove and may cause damage to the stove.
Never leave the stove unattended with the ash door open.
After the layer of coal is burning, a second layer may be
added. After the second layer is burning, more layers may be
added. Do not add coal above the firebricks or grate bars.
Add Even Layers by pouring evenly across coal bed
The stove is hot while in operation. keep
children, clothing and furniture away. Contact
may cause skin burns.
As you begin to operate your stove at higher temperatures,
you will notice a “hot” or unpleasant smell; this is just the
paint going through the curing process, and will disappear
after a few fires.
Overfiring
Avoid overfiring your stove. This is a potentially hazardous
situation which can lead to the overheating of combustible
wall or floor materials, damage to the stove, and in extreme
cases, cause a fire. Overfiring is caused by: Too much air
flowing through the stove too quickly. You may have inad-
vertently left the bottom door open. Or, Not keeping up with
routine maintenance, such as checking door gaskets for wear.
The chimney may have exceesive draw or draft, which can
be remedied by installing a barometric damper
6
4
3
Overfiring results in excessive fuel consumption, and may
cause parts of the stove or chimney connector to glow red.
If you notice signs of overfiring, reduce the air supply to the
fire, and review the Maintenance section in this manual. Do
not burn the stove continuously at the maximum setting. If
maximum heat is required day after day, the stove is too small
for the area you are trying to heat.
2
1
Never leave the stove unattended if either the ash
or load door is open. Overfiring may result.
In the event of a chimney fire, call your local fire depart-
ment; make sure everyone is safely out of the house. Reduce
the air intake of the stove as much as possible using the air
control lever. Do not throw water on the fire; this can cause
stove damage and create an even more dangerous situation.
Have your chimney professionally cleaned and inspected
before resuming burning in your stove.
5
1. Grates
6. Grate Bars
2. Ashes On Grates
3. Partly Burned Coal
4. Fresh Coal
5. Ashes In Ash Pan
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
12
Disposal of Ashes. The TLC 2000 was designed to provide
access to the ash pan without the need for opening the main
door. Wearing heavy protective gloves, open the ash door
and remove the ash pan by pulling it forward by the handle.
Close the ash door before taking the ashes outside for safe
disposal.
A good time to empty the ash pan is before loading. This
ensures that the ashes will be cold and safer to handle than
directly after shaking the ashes down or tending the fire.
Ashes should be placed in a steel container with a tight
fitting lid and moved outdoors immediately. The closed
container of ashes should be placed on a noncombustible
floor or on the ground, well away from all combustible
materials, pending final disposal. If the ashes are disposed
of by burial in soil or otherwise locally dispersed, they
should be retained in the closed container until all cinders
have thoroughly cooled. Other waste shall not be placed
in this container.
Handle
Ash Pan
Handle
Refueling
Open the coal air control to the maximum position by slid-
ing it to the right.Allow the fire to burn vigorously for several
minutes. Shake the grates with short choppy strokes until the
first red coals fall into the ash pan, then stop! Add coal to the
top of the coal bed. It is good to allow some red hot coals ex-
posed to help ignite the gases coming off of the newly added
coal. These gases can be volatile if left accumulate. The coal
air control may be returned to the desired setting.
Cooking Grill
Stainless Steel Cooking Grill (Optional )
The cooking grill can be used for open fire grilling over
anthracite coal or wood.
To install the grill, place the handle in the grill as shown at
left. The grill can now be lifted and positioned in the opening
on top of the stove as shown below left.
CAuTION: COOkING GRILLMAyBE HOT. Always
wear gloves when handling the grill.
Cooking on anthracite coal produces flavor similar to a
gas grill.
Cooking on wood produces many flavors depending on
the type of wood used. More flavor is added when cooking
is done with the top closed. This causes the heat and smoke
to circle around the food.
As with grilling or any open fire cooking, the amount of
heat and cooking time must be experimented with for best
results.
TLC 2000 with cooking grill in action
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
13
Maintenance
Like all fine equipment, your TLC 2000 requires some
routine maintenance and inspection. Follow the guidelines
in this section to guarantee safe, efficient operation.
Glass - Replacement
The glass in this unit is a ceramic glass. 5mm X 444mm
X 311 mm. available from your Harman dealer.
If the stove’s glass is cracked or broken, you must replace
it before operating your stove. Remove pieces carefully.
Replace glass only with Harman supplied replacement glass
panels; do not use substitutes.
To replace the glass panel, you will need to remove the
door. To do this, open the door, lift it straight up and place it
on a soft surface.
The Stove
Surface
The stove’s exterior surface should be dusted periodically
with a soft cloth. For more thorough cleaning, wait until the
stove is cool before using a damp cloth to clean any blemishes.
Controls
Carefully remove damaged glass, gasket material, and
hold down clips (set aside).
To avoid a rust build-up on the inner surfaces of the con-
trols, work the controls back and forth several times, during
the summer, or any prolonged period when you are not using
your stove.
Referring to the diagram, note how the various compo-
nents of the door system fit together. Lay the load door face
down on the soft surface, and install the self adhesive 1/4"
gasket material around the front face of the glass.
Set the glass pane and gasket gently onto the door. Install
the hold down clips and tighten with bolts as shown. Reinstall
door on stove.
The Fire Chamber
The inside of the fire chamber should be examined for
damage to the firebrick lining material, and grates. If any
bricks have been damaged, replace them with Harman re-
placement parts.
venting System / Chimney
Creosote - Formation and the need for removal- When
wood is burned slowly, it produces tar and other organic
vapors, which combine with expelled moisture to form
creosote. The creosote vapors condense in a cool chimney
of a slow burning fire.As a result,
creosote residue accumulates in
the flue lining. When ignited, this
Door
creosote makes an extremely hot
fire. The chimney connector and
Glass Gasket
chimney must be inspected at least
once every two months during the
heating season to determine if a
Glass
creosote build-up has occurred.
If a significant layer of creosote
has accumulated (3mm or more),
it must be removed to reduce the
risk of a chimney fire.
In the event of a chimney fire,
call your local fire department;
make sure everyone is safely out
of the house. Reduce the air intake
of the stove as much as possible
using the air control lever. Do not
throw water on the fire; this can
cause stove damage and create an
even more dangerous situation.
Have your chimney profession-
ally cleaned and inspected before
resuming burning in your stove.
Hold Down Clips and
Bolts
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
14
Glass - Cleaning
Sometimes it will be necessary to clean accumulated ash
from the glass surface; allowing this ash to remain on the glass
for long periods can result in “etching” due to the acidity of
the ash. The creosote which accumulates on the glass should
burn off during your hot fires.
Gaskets are located:
On the doors to provide airtight closure.
On the lid.
Handle
Never clean the glass while it is hot, and do not use abra-
sive substances. Wash the surface with cool water, and rinse
thoroughly. You may wish to use a non-abrasive cleaner
specifically designed for use on stove glass. In any case, dry
thoroughly before relighting your stove.
The handle on the front door of your TLC 2000 is attached
to a threaded shaft. After a period of time, you may find that
the front door does not close as firmly as when your stove was
new. This is due to a natural compression of the gaskets. To
tighten the seal, open the door and rotate the handle one full
turn counterclockwise or bend the latch plate on the stove.
Gaskets
Gaskets are used on the doors and top lid of the TLC 2000.
You must check these gaskets from time to time, and replace
them when necessary. The gaskets are made of fiberglass of
different sizes (obtainable from Harman Dealer) and are fixed
in place with a high temperature stove gasket cement. To
change a gasket, first remove the worn fiberglass and clean the
area with a wire brush.Also clean any other surfaces that come
into contact with the gasket. Place a small bead of cement in
the area under the gasket, then press new gasket material into
the channel; do not overlap the ends. Seat the gasket firmly by
applying pressure when possible; for example, after chang-
ing the door gasket, close the door. Allow the cement to dry
before using your stove.
Blower
The optional blower on your TLC 2000 stove requires very
little maintenance. You should, however, keep the air inlet and
the motor free of dust and dirt.
Lid Gasket
Door Gasket
Rotate door handle one full turn
counter-clockwise to tighten door
seal.
Glass Gasket
Ash Door Gasket
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
15
Installation
DO NOT INSTALL IN A SLEEPING ROOM
Assembly
Blower ( Optional )
Bolt the blower to the bottom rear of the stove with four
1/4-20 bolts. Tighten the bolts, but do not overtighten.
The blower speed can be adjusted using the knob that is
built-in to the power cord. When first starting a fire, keep the
blower off. After a good bed of coals is established, you can
run the blower at any speed desired.
Blower Variable
Speed knob
The power cord for the blower must be connected to a
grounded outlet, and must be routed away from the appliance.
Top Air Grill
Top Air Grill ( Optional )
The top air grill must be installed before the chimney con-
nector is installed.
To install simply place the top air grill over the flue out let
and position as shown at left. It is held in place by gravity.
The top air grill is a decorative option that does not add or
subtract from the performance of the stove.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
16
Floor Protection
Parallel versus Corner Installations
In all installations, the area under and around the stove
must be protected from falling ash and live coals. The
floor protector must be of noncombustible material, and
positioned as shown in the accompanying illustration.
Aparallel installation is one in which the back and sides
of the stove are parallel to the walls behind and to the side
of the stove. Acorner installation is one in which the back
of the stove is positioned diagonally across a corner of the
room. Each installation requires its own set of clearances.
For parallel installations the required clearance dis-
tances from the stove are: 18" (457mm) to the side wall
and 16" (405mm) to the back wall. From the chimney
connector to the rear wall must be 18" (457mm), to the
side wall 27" (685mm) and to the ceiling, 36" (914mm).
Fireplace installations must meet these same clearance
requirements; specifically follow these guidelines for
mantel and trim clearances.
For corner installations, the clearance distances from
the stove are 12" (305mm) from each corner of the stove
measured straight to the nearest combustible material.
From the front of the stove, clearance to combustible
materials such as furniture, curtains, fuel, etc., is: 48"
(1219mm) in the U.S. and 60" (1524mm) in Canada.
The guidelines for floor protection are:
1) Completely under the stove and any horizontal runs
of connector. The floor protection must extend a mini-
mum of 2" (51mm) beyond each side of the horizontal
connector;
2) 8"(203 mm) to each side and to the rear of the ap-
pliance;
3) U.S. 16"(405 mm) in front of the doors; Canada
18" (457 mm) in front of the doors.
Clearances
Clearance is the empty space required between the
stove or chimney connector to the nearest combustible
surface or object, such as walls, ceilings, floors, or furni-
ture. Clearance distances may only be reduced by using
methods approved by either the CAN/CSAB365 standard
(Canada) or NFPA 211 (U.S.) Contact your building au-
thority for information if you are interested in reducing
clearance distances other than those presented here.
Wall
Wall
16" / 18" /
405mm 457mm
12"
305mm
18"
457mm
8" /
203mm
18"
457mm
27" /
685mm
12"
305mm
8" /
8" /
203mm
203mm
USA: 16"
405mm
Canada: 18"
457mm
Floor Protector
Floor Protector
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
17
The Chimney System
Soot and Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic
vapors, which combine with expelled moisture to form soot
or creosote. The soot and creosote vapors condense in the
relatively cool chimney flue of a slow burning fire.As a result,
soot or creosote residue accumulates on the flue lining. When
ignited, this soot or creosote can result in an extremely hot fire.
The chimney connector and chimney should be inspected
at least once every two months during the heating season to
determine if a soot or creosote build-up has occurred. If soot
or creosote has accumulated (3 mm or more) it should be
removed to reduce the risk of a chimney fire.
Checking your chimney and chimney connector more fre-
quently, especially while you are getting used to your stove,
is recommended. To inspect this system, let the stove cool.
Using a flashlight and mirror, check the interior of the chimney
connector, and the chimney itself.
To clean deposits from the surface of the connector, use a
stiff wire brush after dismantling the connector assembly. To
clean the chimney, use a specially designed brush sized to fit
your particular flue opening, or call an established chimney
cleaning service.
At the end of the heating season, perform a thorough examina-
tion of your chimney system, and have it repaired if necessary.
Draft
guidelines in this manual, including size, type, and height to
avoid draft problems.
When installed and operated according to this manual, the
TLC 2000 will produce enough hot gases to keep the chimney
warm so that adequate draft is maintained throughout the
burn cycle.
Chimney Connectors
In general, following these guidelines will ensure compli-
ance with all national and provincial codes; prior to beginning
your installation, check with your local building code official
to check on additional local regulations which may influence
the design and placement of your venting system.
The Harman TLC 2000 may be installed with (150 mm) 24
gauge chimney connector pipe. Size of the connector should
correspond to the size of the flue collar opening. Do not use
makeshift compromises. No part of the chimney connector
may pass through an attic or roof space, closet or other
concealed space, or through a floor or ceiling. Whenever
possible, avoid passing the connector through a combustible
wall; if you must, use an approved wall pass-through, de-
scribed later in this section.
Assemble the connector beginning at the flue collar, with
the crimped ends pointing towards the stove (to keep debris
and creosote flakes inside the system). Each joint, including
the one to the stove’s flue collar and the one to the chimney
itself should be secured with at least three sheet metal screws.
Screws may be a maximum of 3 inches apart. A 1-1/4" (30
mm) overlap is required at each joint, including the flue col-
lar attachment. No more than two 90 degree elbows should
be used, and the total length of connector should not exceed
10 feet (3 m). All horizontal runs of connector must have a
minimum upward slope of 1/4"(6 mm) per foot (20 mm per
meter).
Draft is widely misunderstood. It is important that you,
the stove operator, realize that draft is a variable effect, not
a given quantity. Stoves and chimneys do not have draft, yet
draft is the key to your stove’s performance.
Draft is a force, produced by an operating stove and the
chimney to which it is attached. It is created by hot gases rising
up the chimney, creating a pressure difference between the
inside of your home and the outside air. It continually moves
fresh combustion air into the stove, and hot exhaust gases out
of the stove; without this constant flow, the fire will go out.
Other factors, such as barometric pressure, winds, the
airtightness of the home, the total inside chimney volume,
chimney height and the presence of venting devices such
as exhaust fans also play a role in maintaining an adequate
draft. In some cases, a window may need to be left open, or
some other source of fresh air provided, to keep the appli-
ance operating properly. Low barometric pressures, super
insulated homes and exhaust fans can reduce draft; winds can
play havoc with draft; and too large or too small a chimney
volume can cause reduced draft due to the excessive cooling
or not enough room to vent exhaust gases quickly.
Some signs of inadequate draft are smoking, odor, diffi-
culty in maintaining the fire, and low heat output. Overdraft
can be caused by a very tall chimney even if it is the recom-
mended size, and can cause overfiring of your stove. Signs
of an overdraft include rapid fuel consumption, inability to
slow the fire, and parts of the stove or chimney connector
glowing red. It is important that you follow the chimney
Wall Pass-throughs
Occasionally it is necessary to pass the chimney connector
through a combustible wall to reach the chimney. Depending
on your local building codes, and the pertinent provincial or
national codes, there are several choices for accomplishing
this safely. Before beginning your installation, contact local
officials, and also the chimney connector and chimney manu-
facturer for specific requirements.
Canada. Three methods are approved by the Canadian
Standards Association. The diagram shows one method re-
quiring an 18"(450 mm) air space between the connector and
the wall. It allows use of one or two covers as described in
the diagram. The two other methods are described in detail in
the current issue of CAN/CSA B365, the national standard.
United States In the U.S., the national code is NFPA 211.
While many localities adopt this standard, be sure to check
with local authorities before beginning your installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
18
Non-combustible cover, one
side only. If two covers are
used, each must be mounted
on non-combustible spacers
at least 7/8" (21mm) away
from the wall.
Closest
Combustible
Material
Minimum 2" (50mm)
Clearance to Brick
Hole with a minimum
clearance of 18" (450 mm)
between connector and wall.
Minimum 12"
Liner
(300mm) to Brick
Fire Clay
Thimble
Chimney
Connector
1" (25mm)
Clearance
Masonry Chimney Built to
NFPA 211 Specifications.
Minimum 12" (300mm)
to Combustibles
AN APPROVED CANADIAN
AN APPROVED U.S.
WALL PASS-THROUGH
WALL PASS-THROUGH
The NFPA (National Fire Protection Association) permits
four methods for passing through a combustible wall. A
commonly used method to pass through a wall directly to a
masonry chimney is to clear a minimum 12"(300 mm) around
the entire chimney connector, and fill it with brick masonry
which is at least 3.5"(90 mm) thick.Afireclay liner, minimum
3/8" (9 mm) wall thickness must run through the brick wall
to the chimney liner (but not beyond the inner surface of the
liner). It must be cemented in place with refractory cement.
This method is illustrated. For details on the other three op-
tions, refer to the most recent edition of the NFPA 211 code.
More Than 10 ft. (3m)
Height Necessary
Above Any Roof Sur-
face Within 10ft. (3m)
10 ft. (3m)
2 ft. (0.6m) min.
3ft. (0.9m)
minimum
above
The Chimney
exit
point
Ridge
The TLC 2000 must be installed into a chimney approved
for use with solid-fuel appliances. In the U.S., the TLC 2000
must be connected to (1) a prefabricated chimney complying
with the requirements for Type HT chimneys in the Standard
for Chimneys, Factory-Built, Residential Type and Building
HeatingAppliances, UL103, or (2) a code-approved masonry
chimney with a flue liner. In Canada, the TLC 2000 is listed
for use with prefabricated chimneys tested and listed to the
high temperature (650 degrees C) chimney standard, ULC
S-629, or with a code approved masonry chimney.
The minimum recommended height for any chimney is
16 ft (4.8 m) above flue collar height. A round flue (either
masonry or approved prefabricated), of either 6" (150 mm),
7" (180 mm) or 8" (200 mm) may be used. For square or
rectangular masonry chimneys, nominal sizes of 8" x 8"or 8"x
12" (200 mm x 200 mm, 200 mm x 300 mm) may be used.
Chimney
The 3-foot, 2-foot, 10 foot rule
Codes require that solid-fuel chimneys extend 3 ft (0.9 m)
above the point at which they exit from the roof, provided
that no part of any structure is within the top of the chimney,
then the chimney must extend 2 ft (6 m) above the highest
point with the 10 ft (3 m) radius top height. If there is not
ten feet of clearance from the top of the chimney, then the
chimney must extend 2 ft (6m) above the highest point with
the 10 ft (3m) radius.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
19
dONOTCONNECTThISuNITTOAChImNEY
FluE SErvINg ANOThEr APPlIANCE.
Existing Masonry Chimneys
If you plan on using a pre-existing masonry chimney, have
it thoroughly inspected and cleaned. Any faults which make
the chimney unsafe and unusable must be repaired prior to
use. These can include improper height, structural defects,
blockages, inadequate clearance to combustibles, unsealed
openings into other rooms of the house, signs of creosote or
smoke leakage, a loose or absent clean-out door, or absence
of a liner.
DO NOT CONNECT TO ANy AIR
DISTRIBuTION DuCT OR SySTEM
venting to a Masonry Chimney
When connecting to a masonry chimney, several provisions
are standard. First, whether the chimney connector is vented
to the chimney through a thimble or a breech pipe, neither
must pass beyond the inner surface of the chimney liner, and
both must be firmly cemented in place with refractory cement.
(A thimble is a masonry pipe which is inserted through the
chimney wall, and is frequently the preferred method; a breech
pipe is a piece of steel pipe used the same way.) In Canada,
a breech pipe has ridges or protrusions to lock it firmly into
the refractory cement. In either case, the chimney connector
vents to the chimney through the thimble or breech pipe.
Using a thimble, the connector slides completely inside the
masonry to the inner edge of the flue liner, and may be eas-
ily removed for chimney and connector inspection. A breech
pipe must extend at least 2" (50 mm) into the room, so the
connector can be attached with sheetmetal screws.
Installing to a Prefabricated Chimney
When venting your TLC 2000 using a prefabricated chim-
ney, be sure to contact local building code authorities, and
to follow the manufacturer’s instructions exactly. Use only
the manufacturer’s parts; do not use makeshift installation
techniques. All prefabricated chimneys must be tested to
UL
either the U.S. or Canadian high-temperature standards,
103 or ULC-629.
WARNING: DO NOT INSTALLIN SLEEPING
ROOM.
The Harman TLC 2000 was tested with the fuel door open
and closed.
venting to a Masonry Fireplace Chimney
If you operate with the door open, be sure to install the
optional fire screen, and be sure the bypass damper is open.
Do not burn any fuel other than those specified. Other
solid fuels, such as charcoal, can cause increased carbon
monoxide production or overfiring. Never use highly volatile
substances in your stove, such as gasoline, which could cause
an explosion.
When solid fuels are burned completely, they produce
water and carbon dioxide. However, in long slow burns, a
substantial amount of carbon monoxide may be produced.
If allowed to build up, carbon monoxide (which is odorless)
can prove fatally poisonous. Proper ventilation and draft will
prevent this from happening. If you smell smoke, turn up the
air control lever setting, and thoroughly ventilate your dwell-
ing. During future burns, be careful not to overload the stove
with fuel, so you will not be tempted to constantly operate at
a low air control setting.
In some situations, a code compliant chimney originally
used for a masonry fireplace may be used to install your TLC
2000. In addition to the requirements found in the previous
paragraphs, it is important to be aware that all clearances
must be met, including those from the chimney connector to
combustibles — 18" (360 mm) to sides and 18" (450 mm) to
ceiling. Do not forget to include floor protection in your plans.
(See Clearances and Floor Protection in this section.) Since
many fireplaces have exposed wooden mantels and trim, pay
special attention to the clearances necessary to these materials.
If your fireplace chimney is behind a combustible wall,
you must use an approved wall pass-through system to gain
access to the masonry chimney. The chimney connector must
enter the chimney at a place where it is lined, and the fireplace
must be made inoperable. For example, you might remove the
damper, replacing it with a secure, airtight, noncombustible
seal (removable for inspection); this also satisfies the require-
ment that no room air must be allowed to enter the chimney.
Other causes of poor ventilation or draft are icing, exhaust
fans, a blocked outside air inlet, and room air starvation. If
your stove is sluggish and you get occasional odor, check these
possibilities and increase the air flow in your home.
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Parts
TlC-2000
beginning manufacturing date: N/A
Ending manufacturing date: Active
Top load Coal/wood Stove
1-90-08690-1 (black w/door), 1-70-08690-4 (metallic blue), 1-70-08690-5 (honey glo),
1-70-08690-10 (mojave red), 1-70-08690-12 (Forest green),
((Ending manufacturing date: june 2011)--1-70-08690-1 (black) 1-70-08690-2 (Charcoal), 1-70-08690-3 (goldenfire))
1
2
3
4
5
6
22
7
21
8
20
19
9
10
18
11
17
12
13
14
16
15
Part number list on following page.
06/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Parts
TlC-2000
beginning manufacturing date: N/A
Ending manufacturing date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at depot
ITEm
1
dESCrIPTION
Top Air Grill Assembly (Option)
COmmENTS
PArT NumbEr
1-00-08710
2
Top, Rear
2-00-852109L
3
Top Load Door Assembly
Gasket, Bulb black 1-1/2” X 9-32 w/psa (top plate)
Gasket Plate w/gasket
Damper Linkage Arm Weldment
Wooden Knob (damper handle)
Shield, left side
1-10-08720A
4
5 FT
1-00-10050
Y
5
1-10-08759A
1-10-08722
6
Y
Y
Y
Y
Y
Y
Y
Y
7
2 Sets
1-00-05228
8
2-00-852139P
1-10-852166
1-00-08643
9
Shaker handle weldment
Blower option - includes 3 speed control
Grate, long 15 in - cast
Grate link
10
11
12
13
14
15
Qty 2 req
3-00-00208
2-00-852119
1-00-900450125
1-00-0872456
1-10-08718A
1-00-85223
Brick 9” X 4-1/2” x 1-1/4”
Brick Supports
Pkg of 7
1 Set
Ash Door Assembly
Ash Door Latch Hardware
Airslide Knob
Y
Y
16
17
18
Pkg of 3
3-40-08746-3
1-10-08690
Ash Pan
Ash Lip Trim
Gold
3-43-4722386
1-00-08711-1
1-00-08711-4
3-40-08214
Door Kit Assembly
Black Classic
No longer available
19
Door Kit Assembly (Gold)
Glass Rect 12-7/16” X 17-5/8”
Door Frame - Roped (Gold)
Door Frame - Roped
Coal Bar and Holder
Shield, right side
Y
No longer available
1-10-05165
Cast
4-00-05165
20
21
22
1 Set
1-00-852144
2-00-852141P
2-00-852153
Y
Y
Cleanout, TLC
Additional service part numbers appear on following page.
06/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Parts
TlC-2000
beginning manufacturing date: N/A
Ending manufacturing date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at depot
ITEm
dESCrIPTION
COmmENTS
PArT NumbEr
3-43-08725
Air grill trim
Bolt (ash door hinge)
Brass Elbow
2-00-06952B
3-40-00121
Brick Backer
Qty 2 req
2-00-852147
1-00-08709
3-40-727336
3-30-2019-15
1-00-1086204
1-00-2312
Y
Cooking grill - Option (w/handle)
Cozy screen
Dowel pin 1/4 X 3/8
Pkg of 15
20 Ft
Gasket 1/2” round rope (Front load door)
Gasket, Round black 1/4” w/psa (glass)
Gasket, Round white ld 5/8” (ash door)
Glass retainer clip
Y
Y
Y
Y
15 Ft
1-00-10000
2-00-05202-4
2-00-852169L
1-00-04174
4-31-08055
3-30-3011-100
3-30-6007-25
1-10-08717
3-50-03372
3-50-03373
3-31-08558
3-20-02223
1-00-00122
Pkg of 4
1 Set
Handle, Cooking Grill
Hinge - old style “punched”
Paw bolt (old style)
Y
Y
Y
Y
Y
Y
Screw, #10-24 x 3/8” Alloy Steel Black Oxide Button Head Cap
Screw, 1/4”-20 x 2 1/2” Phillips Round Head Zinc Pltd Machine
Shaker bar weldment
Pkg of 100
Pkg of 25
Shaker bushing
Shaker shaft
Spring washer - plated 6mm
Variable speed control w/off
Wooden handle (front door)
Y
06/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood Pellet
Coal Electric Venting
Wood
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
1 Year
X
X
X
X
X
X
Igniters, electronic components,
and glass
X
X
X
X
X
X
2 years
X
X
X
Factory-installed blowers
Molded refractory panels
3 years
X
X
Firepots and burnpots
Castings and baffles
5 years 1 year
X
X
Manifold tubes,
HHT chimney and termination
7 years 3 years
X
X
10
1 year
years
X
X
X
Burners, logs and refractory
Firebox and heat exchanger
Limited
3 years
Lifetime
X
X
X
X
X
X
X
X
All replacement parts
beyond warranty period
90 Days
X
X
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CONDITIONS:
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
•
•
This warranty is only valid while the HHT appliance remains at the site of original installation.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
•
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
•
•
•
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-
ation of glass.
•
•
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
•
•
•
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
•
•
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645C 12-29-10
Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Proudly Printed On 100% Recycled Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
|