4” LED TAIL LIGHT
FLANGE MOUNT
94795
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.
11. Make certain to follow all local laws regarding vehicles and tail lights.
12. Do not cut or rewire any part of the Tail Light or vehicle.
13 Make certain the vehicle is turned off before performing any installation, service or
maintenance.
14. Harbor Freight Tools is not responsible for damage to the Light or to the vehicle which is
a result of improper installation.
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Flange Mount 4” LED Tail Light, check to make sure that the product is intact
and undamaged. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS
at: 1-800-444-3353.
Installation
Your 4” Flange Mount Tail Light will require complete installation. It is important that you read the
entire manual to become familiar with the product BEFORE you install and use the 4” Tail Light. If
you do not have experience doing this type of electrical work, the job should be done by an
automotive service technician.
1.
Make certain that the vehicle is OFF and the battery disconnected before installation or
performing service or maintenance. Proceed with the following steps for installing the Tail
Light.
2.
Install the Tail Light into a 4-1/2” round hole facing the rear of the vehicle. If your vehicle does
not have a hole of this size then drilling a hole will be necessary. Make certain that the hole
and connected wiring remain water resistant.
Warning:
When drilling holes, beware of any hidden electrical lines or cables. Make sure
you don’t damage or weaken the structural integrity of the vehicle.
3.
Use a rubber gasket (not included) to line the hole and provide protection for the Tail Light.
Connect the Terminal Pins to your vehicle’s electric wiring system. Always review the
manufacturer’s manual for the vehicle to avoid any damage to the vehicle.
Harbor Freight Tools is not responsible for damage to the Light or to the vehicle which is a
result of improper installation.
SKU 94795
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Each of the Terminal Pins has been marked on the rear of the Tail Light housing; Ground,
Tail, and Stop/Turn. Connect each of the wires from your vehicle to the Tail Light. Make
certain the ground wire, usually white, is connected to the ground Terminal Pin.
WIRING DIAGRAM
WhiteWire
BlackWire
(Ground)
(Tail Light)
RedWire
(Stop / Turn)
5.
6.
Once the wires are properly connected, reconnect the battery. Test the wires and Tail Light
to make certain it is working properly before securing the Tail Light in place.
Use 3/16” diameter hardware in each of the three screw holes to secure the Tail Light in
place. Mounting hardware is not included.
No replacement parts are available for this product.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
REV 12/06
SKU 94795
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|