Harbor Freight Tools Utility Trailer 47845 User Manual

FLATBED TRAILER  
WITH ATVTIRES  
Model 47845  
ASSEMBLY and OPERATING  
INSTRUCTIONS  
Note: Wooden stake  
panels are not included.  
Wooden Stake Kit, #40041  
is sold separately.  
Flatbed Trailer is for off-road use only.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
©
®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or  
form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
REV 08/05  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Maintain Trailer with care. Keep Trailer clean for better and safer performance. Follow  
instructions for lubricating and changing accessories. Inspect Trailer periodically, and if  
damaged, have it repaired by an authorized technician.  
10. Stay alert. Watch what you are doing, use common sense. Do not operate Trailer  
when you are tired.  
11. Check for damaged parts. Before using Trailer, any part that appears damaged  
should be carefully checked to determine that it will operate properly and perform its  
intended function. Check for alignment and binding of moving parts; any broken parts  
or mounting fixtures; and any other condition that may affect proper operation. Any  
part that is damaged should be properly repaired or replaced by a qualified technician.  
12. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty. Only use accessories  
intended for use with this Trailer. Approved accessories are available from Harbor  
Freight Tools.  
13. Do not operate Trailer if under the influence of alcohol or drugs. Read warning  
labels on prescriptions to determine if your judgment or reflexes are impaired while  
taking drugs. If there is any doubt, do not operate the Trailer.  
14. Maintenance. For your safety, maintenance should be performed regularly by a  
qualified technician.  
15. This Trailer is not designed for highway or night use. Flatbed Trailer is for off-  
road use only.  
Warning:The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot be  
built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure the parts listed on page 6 are included. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Refer to the Assembly Drawing on page 7.  
1. Attach the four Support Panels (A2) to the Axle (A6) using four Bolts (B1) and Lock  
Nuts (B2). Set aside.  
2. Attach the Connect Bar (A5) to the Tow Bar (A4) with two Bolts (B5) and two Lock  
Nuts (B6).  
3. Attach the Support Bracket (A3) to the Tow Bar (A4) with L Pin (B7) and secure it  
with cotter R Pin (B8).  
4. Connect the other end (the end without the Connect Bar (A5) of the Tow Bar (A4) to  
the center of the Axle (A6) using Bolt (B4) and Lock Nut (B2).  
5. WHEEL BEARINGS AND WHEEL ASSEMBLY  
A.  
The wheel bearings are shipped dry and MUST be packed with bearing grease prior to  
assembly. Wear latex gloves and apply grease liberally around the bearing rollers.  
B.  
Wipe the two bearing races on each wheel clean. It is also recommended that the  
inside of the where the dust cap will go be wiped with some grease. This will remove  
surface rust and make the installation of the caps easier.  
C.  
D.  
Insert the bearings into one wheel, matching the taper of the rollers to that of the races.  
Hold the bearings in place, while sliding the hub over the axle. Slide one large Washer  
(A8) over the spindle, then install and hand-tighten one Castle Nut (A9) to retain the  
wheel. Repeat with the other wheel.  
Tighten the Castle Nut firmly, but not excessively. A 31mm socket wrench is best for  
this. Now back the nut off so that the nearest slot in the shoulder aligns with the cotter  
pin hole in the spindle. Test the wheel for free rotation. If necessary, loosen the nut  
another slot (1/6 of a turn), and check again. The wheel should rotate freely, yet have  
minimal side play on the spindle.  
E.  
F.  
Insert the Cotter Pin (A10) through the slot and the spindle hole, then bend the longer  
leg up with small pliers. Repeat steps D and E on the opposite side.  
The dust caps are intended to protect the bearing. They fit tightly and require some  
patience to install. Tap them in with a mallet.  
6. Set the Frame (A1) so that the holes in the center of the bracket crossing the middle  
of the bed line up with the four holes on the top of the two Support Panels (A2). Make  
sure the Frame (A1) is positioned with the two holes facing front (see Assembly  
Drawing on page 7). Loosely attach them with four Bolts (B1) and four Lock Nuts  
(B2).  
7. Attach the top of the Support Bracket (A3) to the two holes on the front of the Frame  
(A1) with two Bolts (B3) and Lock Nuts (B2). Go back and tighten the hardware used  
in step 6 above.  
8. If using wooden stake side panels (not included), slide the two side panels into the  
Bed Frame Sockets (see Assembly Drawing on page 7). Repeat with two front/rear  
panels. Make sure the vertical supports that fit into the sockets face the outside of the  
Trailer. Secure each side panel into the Bed Frame Sockets by inserting a screws  
(screws included in Wooden Stake Panel Kit).  
REV 05/03; 12/03; 05/05  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Note: When loading or unloading the Trailer, always block both wheels on both sides of the  
wheels. See FIGURE 1.  
Note: Always connect, load, and unload the Trailer on a flat, level, dry surface.  
1. Attach the Connect Bar (A5) to the towing vehicle. Read the towing vehicle manual for  
towing and hitch connection procedures and safety warnings.  
2. To tilt the Trailer as shown in FIGURE 1, hold onto the Support Bracket (A3) firmly  
while removing the L Pin (B7) and the cotter R Pin (B8). Slowly tilt the bed. If using  
rear stake panel (not included), remove the panel and empty or load the Trailer.  
Replace the Rear Panel.  
3. When finished, bring the bed back to the original position so that the hole on the  
Support Bracket (A3) lines up with the hole on the Tow Bar (A4). Replace the L Pin  
(B7) and the cotter R Pin (B8).  
FIGURE 1  
Block both sides  
of each wheel.  
REV 05/03  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List  
Part  
A1  
A2  
A3  
A4  
A5  
A6  
A7  
A8  
A9  
A10  
B1  
B2  
B3  
B4  
B5  
B6  
B7  
B8  
Description  
Frame  
Qty.  
1
4
1
1
1
1
2
2
2
2
12  
15  
2
1
2
2
1
Support Panel  
Support Bracket  
Tow Bar  
Connect Bar  
Axle  
Wheel (Bearing, Dust Cap)  
Large Washer  
Castle Nut  
Cotter Pin  
Bolt M10 X 16  
Lock Nut M10  
Bolt M10 x 65  
Bolt M10 x 100  
Bolt M8 x 16  
Lock Nut M8  
L Pin  
R Pin  
1
Maintenance  
1. Periodically tighten all of the Trailer hardware.  
2. Before each use, tap the Wheel Dust Caps with a rubber mallet and check the tires to  
make sure they are mounted securely.  
3. Keep the Connect Bar (A5) clean of dirt, grease, or debris.  
4. Make sure the tire pressure is at 12 PSI before each use.  
5. When needed, lubricate inside the wheel hubs on the axle with high quality axle  
grease.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES  
ANY REPRESENTATION OR WARRANTY OF ANY KINDTO THE BUYERTHAT HE OR SHE IS QUALIFIED  
TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY  
PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
REV 05/03; 12/03; 05/05  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly Drawing  
Note: Front, rear and side  
stake panels are not included.  
Front/Rear Panels  
Side Panels  
Two holes in  
front of frame.  
.
Bed Frame Socket  
with Bolt hole  
Dust Cap  
.
.
A8  
A9  
A10  
Dust Cap  
REV 05/03; 12/03  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bearing Packing Instructions  
Important  
Read and adhere to the following instructions; failure to read and  
obey all of the following instructions COMPLETELY will void the war-  
ranty and can result in damage to the trailer, property damage, or SERI-  
OUS PERSONAL INJURY.  
Whenever a hub is disassembled (if a hub on a new unit requires  
assembly or a hub is disassembled for maintenance), the following pro-  
cedure MUST be followed.  
1.  
Using a suitable solvent, thoroughly clean the bearings and the rest of  
the parts in the Hub assembly of all grease, dirt, metal shavings, or any  
other foreign object. The parts must be cleaned even if they are new  
or appear clean.  
2.  
3.  
Allow all pieces to dry completely.  
Make sure that your hands are thoroughly clean and the bearing packer  
(not included) is also thoroughly clean.  
4.  
5.  
Place fresh, clean bearing grease in the packer.  
With the grease-filled bearing packer in one hand and the bearing in the  
other, press the bearing into the grease, forcing the grease inside the  
slots in the bearing, continue doing this until every slot in the bearing is  
completely full of grease.  
6.  
Finish assembling the hub/wheel assembly as explained in the manual,  
being careful not to get any dirt or debris on any part of the assembly.  
SAVE THESE INSTRUCTIONS.  
SKU 47845  
For technical questions, please call 1-800-444-3353.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Bouncy Seat 8970COT User Manual
GTO Safety Gate 10 User Manual
Hamilton Beach Iron 14515 User Manual
Harbor Freight Tools Planer 94840 User Manual
Harbor Freight Tools Spreader 90304 User Manual
Honeywell Thermostat CT54 User Manual
Honeywell Thermostat CT1950 User Manual
Hoshizaki Refrigerator 71357 User Manual
Hunter Fan Outdoor Ceiling Fan 42637 01 User Manual
IBM Computer Hardware PCM 5896 User Manual