SEWING MACHINE - SINGLE NEEDLE
Model 92966
ASSEMBLY,SEtup,AND ADjuStiNg iNStRuCtiONS
Shown mounted to table (Sku 3929; not included)
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
tO pREVENt SERiOuS iNjuRY, READ
AND uNDERStAND ALL WARNiNgS
AND iNStRuCtiONS BEfORE uSE.
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
for technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
this product was designed. It will do the job better and more safely at the rate for which
it was intended. Do not modify this product and do not use this product for a purpose
for which it was not intended.
6.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving
parts. Protective, electrically nonconductive clothes and nonskid footwear are recom-
mended when working. Wear restrictive hair covering to contain long hair.
7.
8.
Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across running machines.
Maintain tools with care. Keep needles sharp and tools clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and, if damaged, have them repaired by a qualified technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
9.
Disconnect power. Always turn the machine off and, if possible, disconnect the power
plug of the machine from the receptacle before adjusting, repairing, or cleaning the
machine; leaving the machine unattended; tilting the machine head; or removing the
V-belt.
10.
11.
12.
13.
Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the machine work surface before plugging it in.
Avoid unintentional starting. Be sure the switch is in the Off position when not in
use and before plugging in.
Stay alert. Watch what you are doing, use common sense. Do not operate when you
are tired.
Check for damaged parts. Before using any product, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any part
that is damaged should be properly repaired or replaced by a qualified technician. Do
not use if any switch does not turn On and Off properly.
14.
15.
guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool. Approved accessories are available from Harbor Freight Tools.
16.
17.
Do not operate tool if under the influence of alcohol or drugs. Read warning labels
if taking prescription medicine to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
use proper size and type extension cord. If an extension cord is required, it must be
of the proper size and type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or cause electrical damage
to the tool. This tool requires use of an extension cord with up to 10 amps capability
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
(up to 50 feet), with wire size rated at 18 AWg. Longer extension cords require larger
size wire.
18.
19.
Maintenance. For your safety, service and maintenance should be performed regularly
by a qualified technician.
people with pacemakers should consult their physician(s) before using this
product. Electromagnetic fields in close proximity to a heart pacemaker could cause
interference to or failure of the pacemaker.
20.
21.
22.
Keep hands away from the needle when you turn the power switch on, or while
the machine is operating.
Do not place your fingers into the thread take-up cover while the machine is
operating.
During operation, never place your head, hair, or hands in the proximity of the
hand wheel, V-belt, bobbin winder, or motor.
23.
24.
25.
Do not operate the machine with any safety guards removed.
this machine shall only be operated by appropriately trained operators.
for your personal protection, we recommend you wear ANSi-approved safety
glasses when using the machine.
26.
27.
if oil or grease comes in contact with your eyes or skin, immediately wash the
affected areas and consult a physician.
tampering, modifying or altering any device (aside from the cord and plug by a
licensed electrician) on the machine is prohibited and will void manufacturer’s
warranty.
28.
Repair, adjustment, and specific maintenance shall only be performed by a quali-
fied service technician. Alteration or replacement of the 3 prong grounded electrical
plug provided with the machine must only be performed by a licensed electrician. This
machine must be properly grounded.
Note:Performance of this tool may vary depending on variations in local line voltage.Extension
cord usage may also affect tool performance.
Warning:the warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. it must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
unpacking
When unpacking, check to make sure that the parts shown in the photo on the following
page are included. Note that the machine table shown is not included, and must be ordered
separately. If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual as soon as possible.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Sewing Machine
Table Stand and
Top (not provided)
Power Switch
Knee Lifting Arm
for Presser Foot
Motor
Assembly
The assembly instructions describe mounting the Single-Needle Sewing Machine (Model
92966) to the Table Stand (Model 03929), not included. In order to complete this procedure,
you must first purchase and assemble the Table Stand Kit (Model 03929).
1.
Locate four corner rests in the rectangular hole of the Table Stand where the machine
will sit.
2.
3.
Place two rubber seats (A) on the operator-side and secure with supplied hardware (C).
See figure 1.
Place two rubber hinge rests (B) on the hinge-side and secure with supplied hardware
(C).
4.
5.
6.
Seat the Oil Pan (D) on the corner seats (A). See figure 2.
Insert Hinges (E) into the machine bed. See figure 3.
Fit the machine head’s hinges to the rubber hinge rests (B) before placing the machine
head on the corner seats. See figure 4.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
8.
Tilt the machine back to expose the Oil Pan (D). See figure 5.
Fill the Oil Pan with sewing machine lubrication oil (#7 white oil) to the “high” mark “A”.
Add more oil when the level is to the “low” mark “B”. After lubrication, and during opera-
tion, oil splashing can be seen through the Oil Sight Window (H).
9.
Lower the machine head to the table top.
10. Mount the Motor to the underside of the table top as shown below. Use the supplied
hardware.
Note: Top switch
determines rotation.
Switch left for counter-
clockwise; switch right
for clockwise rotation.
Note: Motor is 110/220V
Single Phase. Disconnect
power and flip switch to
desired voltage. Switch left
for 110V, switch right for
(K)
220V. for 220 V, the power
plug must be rewired by a
qualified technician.
Note: Receptacle
for 6 volt work light
(not included).
11. Place the V-belt around the Sewing Machine Pulley, through the slot in the table top, and
around the Motor pulley. Attach the Pulley Safety Cover.
12. Tighten the V-belt tension by adjusting the long bolt and nut at location (K). The proper
tension is reached when the V-belt can only be deflected 1/2 inch.
13. Mount the Power Switch under the table top, on the operator’s side. Use the supplied
hardware.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Switch
Mounting the thread Stand
Note: TheThread Stand is designed to be mounted on theTable Stand Kit (Model
03929 - not included). Unless indicated otherwise, all parts referred to
in this set of instructions are listed in the Bobbin Winder & Thread Stand
Unit Parts List found on page 23. During assembly, it will be helpful to
refer to that list and the diagram above it on the same page.
14. Locate the large hole in the far right corner (from the location that the operator will be
seated) of the Table (not included). Place the Rubber Washer (10-41) and Washer
(10-33) onto the Lower Spool Rest Rod (10-32) and insert the Rod into the hole mentioned
above. Place anotherWasher (10-33) over the end of the Rod, and thread on and tighten
a Nut (10-34).
15. Place the Spool Support (10-42) over the Lower Column (10-32) about halfway down.
Insert a Screw (10-27) and Nut (10-43) through the Support.
Note: The Support has tabs that hold onto the corners of the Nut to make tightening
easier. When assembling, place the Nut on the side with these tabs.
Tighten the Screw.
16. Insert the threaded end of the Spool Pin (10-36) through one of the holes in the top of
the arm of the Spool Support (10-42). Place a Washer (10-28) and Nut (10-31) over
the end of the Pin and tighten. Place the Spool Rest (10-37), Spool Mat (10-38), and
the Spool Vibration Stopper (10-35) over the end of the Spool Pin. Repeat this step for
both of the Spool Pins (10-36).
17. Place the Column Pipe Connector (10-29) over the top of the Lower Column (10-32)
until the Rod is about halfway through the Connector. Place a Screw (10-30) and Nut
(10-31) through the bottom hole in the Connector and finger-tighten.
18. Place the Upper Spool Rest Rod (10-26) into the top of the Column Pipe Connector
(10-29). Place a Screw (10-30) and Nut (10-31) through the top hole in the Connector.
Tighten all of the Screws and Nuts in the Connector.
19. Place the Thread Hanger (10-24) about halfway over the top of the Upper Column
(10-26). Insert a Screw (10-27) and Nut (10-43) through the Hanger as explained in the
note in step 14, above. Tighten the Screw and place the Column Cap (10-25) over the
end of the Upper Column (10-26).
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Bobbin Winder
figure A
Note: Unless indicated otherwise, all parts referred to in this set
of instructions are listed in the Bobbin Winder & Thread
Stand Unit Parts List found on page 23. During assembly,
it will be helpful to refer to that list and the diagram above
it on the same page.
20. Remove the Belt Cover (part 8-27, on page 21). Swing the
sewing machine so the base is in the operating position,
resting on the table. Set the Bobbin Winder to the ‘ON’
Position-see ON Position, below.
Mark
pilot
Holes
Here.
21. Make sure the Bobbin Winder is in the ‘ON’ position.
Position the Base (Bobbin Winder Base Assembly) (10-1)
so that the Thread Winder Assembly (10-4) lines up with
and just touches the belt. Mark pilot hole locations on the
table at the far end of each of the two channels in the Base
as indicated in Figure A.
figure B
22. Set the Base (10-1) aside and swing the sewing machine
out of the way. Carefully drill straight pilot holes for each of
the two locations marked above. Place the base in location
and secure using two Wood Screws (10-22) and Washers
(10-23). Leave the Screws just loose enough to allow the
Base to slide.
23. Swing the Sewing Machine back into it’s operating position. Put the Bobbin Winder in
the ‘OFF’ position-see OFF Position, below. Slide the Bobbin Winder Assembly close to
the belt until it just barely doesn’t touch it (1/8” gap or less)-see Figure B, above. Tighten
the Wood Screws (10-22) from step 22, above.
24. Put the Belt Cover back on the Sewing Machine before use.
Setup and Adjustment Section Contents
SECtiON
pAgE
Bobbin Winder Operation ..................................................................................................9
Setting Bobbin in Case......................................................................................................9
Needle Attachment...........................................................................................................10
Threading the Machine.....................................................................................................10
Stitch Length.....................................................................................................................11
Reversing Sewing Direction..............................................................................................11
Needle Thread Tension.....................................................................................................11
Bobbin Thread Tension.....................................................................................................11
Thread Take-up Spring .....................................................................................................11
Thread Take-up Stroke .....................................................................................................12
Presser Foot Pressure......................................................................................................12
Presser Bar Height ...........................................................................................................12
Feed Timing......................................................................................................................12
Feed Dog Height ..............................................................................................................13
Needle-to-hook Timing .....................................................................................................13
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Adjustment
10-6
Caution: to properly break-in your new sewing machine, and
avoid possible damage to the machine, sew at moderate to slow
speeds for the first 15 minutes of use.
Bobbin Winder Operation
ON
position
The Bobbin Winder assists in winding thread onto the Bobbin.
The Bobbin Winder has two positions, ‘ON’ and ‘OFF’:
Off position The Bobbin Winder won’t contact the belt.
10-6
WARNiNg: Shut the machine off completely before
working around the needle or other moving parts.
ON position
This position is with the Connecting Rod (10-6)
pressed, as shown in Figure C. The Shaft on the BobbinWinder
will spin; winding thread onto the Bobbin.
Off
position
figure C
Winding thread Onto the Bobbin
1.
Place a Bobbin onto the Bobbin
Winder Shaft (10-3) as shown
at point d in Figure C, right.
d
b
2.
Route the Thread from the
Spool (not shown) up through
the Thread Guide Tube (10-39,
point a), the hole in theThread
c
a
Tension Bracket Assembly (10-15, b), over and under
the far side of the Tension Disc (10-17, c), and connect
it to the Bobbin (d). - See Figure D, right.
3.
While the Connecting Rod (10-6) is pressed (as shown
in both Figures C and D) the BobbinWinder will be in the
‘ON’ position and the Bobbin will fill with thread. When
finished, release the Connecting Rod and the Bobbin
Winder will reset to the ‘OFF’ position.
figure D
d
b
Setting the Bobbin into the Bobbin Case
c
1.
Hold the Bobbin so that the thread exit is to the left, and
push the Bobbin into its case.
2.
Feed the thread through slit “A” and pull the thread in
direction “B”. By doing so, the thread will pass under the
tension spring and exit at notch “B”.
3.
Verify that the Bobbin rotates in the direction of the arrow
when thread “C” is pulled.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Needle
Replacement Needle Type: 135 X 17
1.
2.
Unplug the Power Cord from the electrical outlet.
Select a proper needle size according to the thread count and
type of material being sewn.
3.
4.
Turn the Hand Wheel until the needle bar reaches the highest
point of its stroke.
Loosen Screw (2) and hold Needle (1) with its indented part
facing toward the Presser Bar (5-18).
5.
6.
Insert the needle and push it up until it will go no farther.
While holding in place, securely tighten Screw (2).
threading the Machine Head
Set the thread spool on its holder
and guide the thread through
the machine as illustrated to
the left. The numbers in the
illustration indicate the threading
sequence.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Stitch Length
1.
To increase the stitch length, turn the Stitch Length Dial
(1) to the desired number (in millimeters) as indicated
under the scale dot (A) on the machine.
2.
To decrease the stitch length, turn the Stitch Length
Dial (1) to the desired setting. The Feed Lever (2) may
require adjustment to allow the Dial to move.
Reversing Sewing Direction
Depress and hold the Feed Lever (2) to sew in a reverse
direction. After the Lever is released, sewing direction
will automatically return to forward.
Adjusting the Needle thread tension
1.
Turn Tension Adjustment Knob (1) clockwise (A) to
increase thread tension.
2.
TurnTension Adjustment Knob (1) counterclockwise
(B) to decrease thread tension.
Adjusting the Bobbin thread tension
1.
Turn the Tension Adjustment Screw (2) clockwise
(A) to increase bobbin tension.
2.
Turn the Tension Adjustment screw (2)
counterclockwise (B) to decrease bobbin tension.
Changing the thread take-up Spring Stroke and pressure
1.
2.
Loosen Set Screw (2).
To increase the stroke, turn the Tension Knob
Screw (3) clockwise (A).
3.
4.
5.
6.
7.
To decrease the stroke, turn the Tension Knob
Screw (3) counterclockwise (B).
Loosen Set Screw (2) and pull out the Tension
Arm (5).
Loosen Set Screw (4) and remove the Tension
Knob Screw (3).
Turn the Tension Knob Screw (3) clockwise (A) to increase pressure; or turn
counterclockwise (B) to decrease pressure.
Replace Tension Knob Screw (3), tighten Set Screw (4), and replace the assembly.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the thread take-up Stroke
1.
2.
3.
When sewing heavy weight materials, move
theThread Guide (1) to the left (A) to increase
the length of thread pulled out by the Thread
Take-up.
When sewing lightweight materials, move the
Thread Guide (1) to the right (B) to decrease
the length of thread pulled out by the Thread
Take-up.
The normal setting is when the marker line “C” on
the Thread Guide (1) is aligned with the center of
the screw.
Setting the presser foot pressure
1.
Loosen Nut (A), and turn the Presser Spring
Regulator clockwise (a) to increase Presser Foot
pressure.
2.
3.
To decrease Presser Foot pressure, turn the
Presser Spring Regulator counterclockwise (b).
After adjustment, tighten Nut (A).
Adjusting the presser Bar Height
1.
2.
3.
4.
Remove the Rubber Plug (C) on the Face Plate (B). Loosen
the set screw underneath.
Manually adjust the Presser Bar height, and the angle of the
Presser Foot. The normal position is 6 mm clearance.
After adjusting, retighten the Set Screw and replace the Rubber
Plug (C). Check to ensure that the presser foot is not loose.
Manually turn the Hand wheel through a full cycle to verify that
the presser foot will not contact the walking foot or obstruct the
needle. If it does readjust the Presser Foot.
Adjusting the feed timing
1.
2.
3.
Loosen Set Screws (2) and (3) on the Feed Eccentric
Cam (1) and properly position the Eccentric Cam.
Retighten the Set Screws.
To advance the feed timing in order to prevent uneven
material feed, move the Feed Eccentric Cam up
(clockwise).
To delay feed timing and increase stitch tightness,
move Feed Eccentric Cam down (counterclockwise).
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Height of the feed Dog
The Feed Dog is factory adjusted. If the Feed Dog juts out too much, puckering may result
when sewing lightweight materials. To adjust the height of the Feed Dog:
1.
Move the Feed Dog to the front end of the
throat plate.
2.
3.
Loosen Screw (A) of Crank.
Move the Feed Dog (B) up or down to make
the adjustment.
4.
Tighten Screw (A), being careful not to over-
tighten.
Adjusting Needle-to-hook timing
1.
Turn the Hand Wheel to bring the Needle Bar (C) down to the lowest point of its
stroke.
2.
3.
Remove the Rubber Plug (A), then loosen the Set Screw (B).
Move the Needle Bar (C) down until the Eye of
the Needle (D) lines up with the inside surface of
the bobbin case holder (E).
4.
5.
Tighten the Set Screw (B) and replace the Rubber
Plug (A).
Turn the Hand Wheel until the needle descends
about 2.5 mm. For typical hook timing, the hook
should be directly about 1.2 mm above the upper
edge of the needle eye at this point.
6.
After making the adjustments in steps 3 and 4, align the Hook Blade point (5) with the
center of the needle (4).
Provide a clearance of .001” to .004” (0.04 to 0.1 mm) between the needle and the
hook.This clearance is less than 1/64” (almost touching). Securely tighten the three Set
Screws. If the clearance is too small, the tip of the hook will be abraded. If it is too large,
it will lead to skip over.
Maintenance
1.
2.
Machine adjustments should only be performed by a qualified technician.
Check the oil level weekly when the machine is used daily. Add sewing machine oil as
required to the high level marking.
3.
4.
Clean the machine with a clean, damp cloth. Do not use solvents or thinners.
When not in use, cover the machine and store in a clean and dry location.
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 1 - ARM BED
NOtE: When ordering parts from the following lists,
always include the list title, item number and description,
and page number. For example, to order the first part
from page 14 list, you would state:
- Parts List 1 - Arm Bed
- Item #1-1 Arm
- Page: 14
NOtE: Some parts are listed and shown for illustration
purposes only and are not available individually as
replacement parts.
pARtS LiSt 1
part
1-1 Arm
1-2 Spec. Plate
1-3 Rivet
1-4 Washer
1-5 Face Plate
1-6 Rubber Plug
1-6a Rubber
Description
Q’ty
1
1
4
2
1
1
1
part
Description
Q’ty
1
1
1
1
1
1
1
part
Description
Q’ty
2
1
2
1
2
1
1
1-18 Screw
1-19 Tension Disc
1-20 Washer
1-21 Three-eye Finger
1-22 Set Screw
1-23 Screw
1-36 Rubber Plug
1-37 Rubber Plug
1-38 Rubber Plug
1-39 Sliding Plate Assembly
1-40 Screw
1-41 Sliding Plate
1-42 Spring
1-24 Nut
1-6b Rubber
1
1-25 Spring
1
1-43 Screw
2
1-7 Threadcam
1-8 Screw
1-9 Screw
1
1
3
1-26 ThreadReleasingPlate
1-27 Thread Tension Disc
1-28 Thread Take-up Spring
1
2
1
1-44 Bed Leg
1-45 Holder
1-46 Screw
3
1
2
1-10 Side Plate (Left)
1-11 Side Plate (Right)
1-12 Washer
1-13 Screw
1-14 Oil Screen Assembly
1-15 Screw
1
1
1
8
1
1
1
2
1-47 Rubber Plug
1-48 Motor (not shown)
1
1
Thread Tension
Adjusting Bracket
1-30 Screw
1-31 Thread Releasing Pin
1-32 Stopping Plate
1-33 O-ring
1-34 Set Screw
1-35 Thread Finger
1-29
1
1
1
1
1
1
1
Servo motor
FESM-
(Slower replacement for stock
motor, not shown, optional)
Lamp
400
SNU-
21
(Not shown, optional)
1-16 Spring
1-17 Tension Disc
pLEASE READ tHE fOLLOWiNg CAREfuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS QUALIFIEDTO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
REV 01/07
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 2 - NEEDLE fEED MAiN SHAft
pARtS LiSt 2
Hand wheel
REV 01/06
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 3 - fEED MECHANiSM COMpONENtS
pARtS LiSt 3
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 4 - fEED MECHANiSM COMpONENtS
pARtS LiSt 4
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 5 - pRESSER ARM
pARtS LiSt 5
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 6 - fEED MECHANiSM COMpONENtS
pARtS LiSt 6
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 7 - LuBRiCAtiON COMpONENtS
pARtS LiSt 7
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 8 - OiL RESERVOiR
pARtS LiSt 8
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 9 - ACCESSORiES
pARtS LiSt 9
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DiAgRAM 10 - BOBBiN WiNDER AND tHREAD StAND
pARtS LiSt 10
BOBBiN WiNDER
tHREAD StAND
part
Description
Q’ty
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
2
2
part
Description
Q’ty
1
1
1
2
2
1
2
4
1
2
1
2
2
2
2
2
10-1 Bobbin Winder Base Asm
10-2a Thread Winder Base Asm
10-2b Bobbin Winder Stand Shaft
10-2c Spring
10-3 Bobbin Winder Shaft
10-4 Thread Winder Asm
10-5 Screw
10-6 Bobbin Winder Frame Pin
10-7 Connecting Rod
10-8 Screw
10-9 Screw
10-10 Bobbin Winder Spring
10-11 Screw
10-12 Rubber Brake
10-13 Presser Plate
10-14 Screw
10-15 Thread Tension Asm
10-16 Screw
10-24 Thread Hanger
10-25 Column Cap
10-26 Upper Column
10-27 Screw
10-28 Washer
10-29 Column Pipe Connector
10-30 Screw
10-31 Nut
10-32 Lower Column
10-33 Washer
10-34 Nut
10-35 Spool Holder
10-36 Spool Pin
10-37 Spool Rest
10-38 Spool Mat
10-39 Thread Guide Tube
10-40 Thread Guide Grommet
10-41 Rubber Washer
10-42 Spool Support
10-43 Nut
2
1
1
2
10-17 Tension Disc
10-18 Screw
10-19 Tension Spring
10-20 Thread Tension Stud Nut
10-21 Screw
10-22 Wood Screw
10-23 Washer
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90 day
warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THiS WarranTy
iS expreSSly in lieu oF all oTHerWarranTieS, expreSS or implied, inCludingTHeWarranTieS
oF merCHanTabiliTy and FiTneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement.We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty,
then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 92966
for technical questions, please call 1-800-444-3353.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Inc Pressure Washer 3050 User Manual
Grizzly Outdoor Cart H0760 User Manual
Harbor Freight Tools Paint Sprayer 91772 User Manual
Harbor Freight Tools Patio Furniture 9018 User Manual
Harbor Freight Tools Vacuum Cleaner 3394 User Manual
Hotpoint Double Oven DH3B S User Manual
HP Hewlett Packard Server rp7420 User Manual
Hyundai Car Video System H LCDVD704 User Manual
ICP DAS USA Network Card 8430 User Manual
Ikelite Camera Accessories S95 User Manual