18 PIECE HOLE SAW SET
94665
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Use eye and ear protection. Always wear ANSI-approved impact safety
goggles.Wear a full face shield if you are producing metal filings or wood
chips.Wear an ANSI-approved dust mask or respirator when working around
metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and, if damaged, have them repaired by an
authorized technician.
10. Disconnect power.Unplug drilling tool (not supplied) when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before
plugging in drilling tool (not supplied).
12. Avoid unintentional starting. Be sure the switch of the drilling tool (not
supplied) is in the Off position when not in use and before plugging in. Do not
carry any tool with your finger on the trigger, whether it is plugged in or not.
13. Stay alert. Use common sense. Do not operate any tool when you are tired.
14. Take caution as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic.When cutting these
materials, care should be taken to avoid inhalation and minimize skin contact.
15. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment and binding
of moving parts; any broken parts or mounting fixtures; and any other
condition that may affect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician. Do not use a
drilling tool (not supplied) if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with grounded
surfaces such as pipes, radiators, ranges, and refrigerator enclosures.
17. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor FreightTools.
18. Do not operate if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not operate the tool.
SKU 94665
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
19. Use proper size and type extension cord. If an extension cord is required, it
must be of the proper size and type to supply the correct current to the drilling
tool (not supplied) without heating up. Otherwise, the extension cord could
melt and catch fire, or cause electrical damage to the tool. Longer extension
cords require larger size wire. Refer to the drilling tool operator’s manual for
specific extension cord requirements. If you are using a drilling tool outdoors,
use an extension cord rated for outdoor use. (signified by “WA” on the jacket).
20. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
21. Use tools with both hands when required. Many tools such as chain saws,
drills, etc., require the use of both hands when operating.This helps maintain
tool stability and keeps hands away from the working area of the tool.
22. Always follow all the instructions and warnings of the tool used with this
Saw Set.
Product Specific Safety Precautions
1. Be sure to use the correct size Arbor for the Hole Saw size selected. It must
fit exactly, not loose. Use work gloves when handling Hole Saws.
2. Select a drilling tool (not provided) with sufficient power to turn the Hole Saws
and cut into hard woods.The drilling tool must have a chuck that is in good
condition and able to hold the Hole Saw Arbor tight. Loose fittings can
damage the tool and possibly lead to serious injury.
3. When cutting a hole with the Hole Saw, hold the drilling tool with both hands,
and always 90 degrees to the stock being cut. Make sure your work area is
secure while using Hole Saw.
4. Do not use excessive pressure on the drilling tool when cutting a hole. Allow
the Hole Saw to do the work. Excessive pressure can damage the Hole Saw
and drilling tool.
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure that all the parts are included. Refer to the
Parts List and Parts Photo located at the end of this manual. If any parts are
missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual.
SKU 94665
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
Operation
1. Select the desired size Hole Saw.
2. Select the Large or Small Arbor for the Hole Saw.
The correct size Arbor will fit exactly into the Hole Saw.The larger Hole Saws
also require the use of the Bracket (17) and Drill Bit (15). See photos below.
3. Using a wrench (not supplied), loosen the Arbor nut and remove the lower half
of the Arbor.
Place the lower half of the Arbor into the hole in the Hole Saw. Screw in the
Arbor Nut into the top of the Hole Saw.
4. Using a wrench (not supplied), tighten the Arbor nut completely.
To avoid having to hold the sharp cutting edge of the Hole Saw while
tightening, place (and hold) a small screwdriver through the holes in the side
of the Hole Saw.
5. Open the jaws of the drilling tool chuck (not supplied).
6. Place the Arbor shaft completely into the chuck and securely tighten the
chuck.
7. Holding the drilling tool at 90 degrees to the stock, set the Hole Saw on the
stock.
8. Press the drilling tool trigger switch to turn it on.
If the drilling tool is a variable speed type, start cutting the stock slowly until
the circle groove is made in the stock. Then cut faster.
9. When the hole is cut, release the trigger switch and wait for Hole Saw to
come to a complete stop before removing it from the stock.
10. Remove Hole Saw from drilling tool chuck.
Small Arbor (13)
Arbor Nut
Large Arbor (14)
Bracket (17)
SKU 94665
For technical questions, please call 1-800-444-3353
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
1. Clean the Hole Saw after use using a cloth and light oil to prevent rust.
2. Store the Holes Saws and Arbors in the Blow Mold case. Keep in a clean and
dry location.
Parts List
Item
Description
5” Hole Saw
4” Hole Saw
3-1/2” Hole Saw
3” Hole Saw
2-1/2”Hole Saw
2” Hole Saw
1-3/4” Hole Saw
1-1/2” Hole Saw
1-1/4” Hole Saw
Qty
1
1
1
1
1
1
1
1
Item
10
11
12
13
14
15
16
17
18
Description
1-1/8” Hole Saw
1” Hole Saw
3/4” Hole Saw
Small Arbor
Qty
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
Large Arbor
Bit, Drill, 15/64”
Hex Key, 3/32”
Bracket
1
Case, Blow Mold
1
NOTE: Some parts are listed and shown for illustration purposes only and are
not available individually as replacement parts.
Parts Photo
(3)
(1)
(4)
(2)
(7)
(8)
(5)
(6)
(11) (12)
(16)
(18) Blow Mold
Case not shown
(10)
(9)
(14)
(13)
(17)
(15)
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 94665
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
|