4″ HANDHELD TILE SAW
68298 4” Handheld Tile Saw
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
©
®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
h. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be ANSI-
approved and breathing protection must be NIOSH-
approved for the specific hazards in the work area.
c. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
4. Power tool use and care
a. Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
d. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
e. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
c. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
f. When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
3. Personal safety
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
b. Use safety equipment. Always wear eye
protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power
tools that have the switch on invites accidents.
g. Use the power tool, accessories and blades
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
d. Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
If the blade becomes twisted or misaligned
in the cut, the teeth at the back edge of the
blade can dig into the top surface of the
wood causing the blade to climb out of the
kerf and jump back toward the operator.
Tile Saw Safety Warnings
1.
DANGER: Keep hands away from cutting
area and the blade. If both hands are holding
the saw, they cannot be cut by the blade.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below:
2. Do not use to cut metal.
3. Do not use for curve or angle cutting.
Doing so may damage Tile Saw blade.
a. Maintain a firm grip with both hands on the
saw and position your arms to resist kickback
forces. Position your body to either side
of the blade, but not in line with the blade.
Kickback could cause the saw to jump backwards,
but kickback forces can be controlled by the
operator, if proper precautions are taken.
4. Do NOT use with a “wet” attachment
or attempt to lubricate blade.
5. Do not use with a grinding wheel attachment;
only use a diamond cutting disc.
6. Do not use damaged or cracked cutting disc.
b. When blade is binding, or when interrupting
a cut for any reason, release the trigger
and hold the saw motionless in the material
until the blade comes to a complete stop.
Never attempt to remove the saw from
the work or pull the saw backward while
the blade is in motion or kickback may
occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
7. Do not start Tile Saw with cutting blade
already set against tile surface.
8. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
9. Adjust the cutting depth to the thickness of the
tile being cut. Less than a full tooth of the blade
teeth should be visible below the workpiece.
c. When restarting a saw in the workpiece, center
the saw blade in the kerf and check that saw
teeth are not engaged into the material. If
saw blade is binding, it may walk up or kickback
from the workpiece as the saw is restarted.
10. Never hold tile being cut in your hands or across
your leg. Secure the tile to a stable platform. It is
important to support the work properly to minimize
body exposure, blade binding, or loss of control.
d. Support large panels to minimize the risk of
blade pinching and kickback. Large panels tend
to sag under their own weight. Supports must
be placed under the panel on both sides, near
the line of cut and near the edge of the panel.
11. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a″ live″ wire will also make exposed metal
parts of the power tool ″live″ and shock the operator.
e. Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
12. Always use blades with correct size and shape
(diamond versus round) of arbor holes. Blades
that do not match the mounting hardware of the
saw will run eccentrically, causing loss of control.
f. Blade depth and bevel adjusting locking
levers must be tight and secure before
making cut. If blade adjustment shifts while
cutting, it may cause binding and kickback.
13. Never use damaged or incorrect blade
washers or bolt. The blade washers and
bolt were specially designed for your saw, for
optimum performance and safety of operation.
g. Use extra caution when making a ″plunge cut″
into existing walls or other blind areas. The
protruding blade may cut objects that can
cause kickback.
14. Causes and Operator Prevention of Kickback:
•
Kickback is a sudden reaction to a pinched,
bound or misaligned saw blade, causing
an uncontrolled saw to lift up and out of
the workpiece toward the operator;
15. Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp or
tie the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
•
When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward
the operator;
Page 4
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
29. This product is not a toy. Keep it
out of reach of children.
30. Verify that there are no utility lines or
hardware in or near the workpiece. This
is especially critical for plunge cuts.
17. Lower guard should be retracted manually only
for special cuts such as ″plunge cuts″ and
31. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in close
proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure. In addition, people
with pacemakers should:
″compound cuts.″ Raise lower guard by retracting
handle and as soon as blade enters the material,
the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
• Avoid operating alone.
18. Always observe that the lower guard is covering
the blade before placing saw down on bench
or floor. An unprotected, coasting blade will cause
the saw to walk backwards, cutting whatever
is in its path. Be aware of the time it takes for
the blade to stop after switch is released.
• Do not use tool with power switch locked on.
• Properly maintain and inspect to avoid electrical
shock.
• Any power cord must be properly grounded. Ground
Fault Circuit Interrupter (GFCI) should also be
implemented – it prevents sustained electrical shock.
19. DO NOT USE THIS SAW WITH THE SAW
HELD UPSIDE DOWN IN A VISE. The saw
is not designed for such use and cannot
be used safely in that position.
32. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
20. Do not use blades made from high-speed steel,
metal-cutting blades or toothed circular saw
blades. The guards of this saw are not designed
to protect against the failure of such blades.
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
21. Place the larger portion of the saw base
on the larger, supported part of the
workpiece. This will help maintain balance
and control while the cut is completed.
22. Blades must be rated to at least the
maximum speed marked on the tool.
23. Maintain labels and nameplates on the tool. These
carry important safety information. If unreadable or
missing, contact Harbor Freight Tools for
a replacement.
33. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
24. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
34. The warnings, precautions, and instructions discussed
in this instruction manual cannot cover all possible
conditions and situations that may occur. It must
be understood by the operator that common sense
and caution are factors which cannot be built into
this product, but must be supplied by the operator.
25. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
26. When using a handheld power tool, maintain a firm grip
on the tool with both hands to resist starting torque.
Vibration Safety
27. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders. To
reduce the risk of vibration-related injury:
28. Use clamps (not included) or other practical ways
to secure and support the workpiece to a stable
platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups to
ensure medical problems are not being caused or
worsened from use. Pregnant women or people who
have impaired blood circulation to the hand, past
hand injuries, nervous system disorders, diabetes,
or Raynaud’s Disease should not use this tool. If
you feel any symptoms related to vibration (such
as tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
Grounding
TO PREVENT ELECTRIC SHOCK AND
DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are
in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the
tool. Never remove the grounding prong from the plug.
Do not use the tool if the power cord or plug is
damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet,
have a proper outlet installed by a qualified electrician.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
Double Insulated Tools:
Tools with Two Prong Plugs
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE
Outlets for 2-Prong Plug
INSTRUCTIONS.
1. Tools marked “Double Insulated” do not require
grounding. They have a special double insulation
system which satisfies OSHA requirements and
complies with the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the 120
volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension
cord. Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases, you
must use a heavier gauge extension cord. Using
extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and
possible tool damage. (See Table A on page 7.)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
Page 6
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
4. When using more than one extension cord to make
up the total length, make sure each cord contains at
least the minimum wire size required. (See Table A.)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
Read the manual before
set-up and/or use.
WARNING marking concerning Risk of
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Hearing Loss. Wear hearing protection.
WARNING marking concerning Risk
of Fire.
Canada) to indicate it is acceptable for outdoor use.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning Risk of
Electric Shock.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
Properly connect power cord
to appropriate outlet.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
TABLE A: RECOMMENDED MINIMUM
WIRE GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)
EXTENSION CORD
LENGTH
NAMEPLATE
AMPERES
(at full load)
25´ 50´ 75´ 100´ 150´
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
Amperes
A
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Hold the Outer Flange and tighten the Screw
counterclockwise (left-hand thread) until Blade is
fastened securely. See Figure 2, below.
Instructions for Putting into Use
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning
of this manual including all text
under subheadings therein before
set up or use of this product.
TO PREVENT SERIOUS INJURY FROM
ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug
the tool from its electrical outlet before assembling
or making any adjustments to the tool.
Note: For additional information regarding
the parts listed in the following pages, refer to
Parts List and Assembly Diagram on page 13.
Figure 2
Blade Installation
1. WARNING! Do not use wet blades
with this Tile Saw; it is not suitable
for use with lubricant or water.
5. To adjust the cutting depth of the blade, loosen the
Wing Bolt (48) attaching the Protection Cover (28)
grooved bracket welded to the Base Plate (47). Move
motor housing up and down until the desired depth
(below base plate) is achieved. See Figure 3, below.
2. Make sure that Arbor Bushing (34) is attached
onto Spindle and seats into recess on the
face of Inner Flange (33). See Fig. 1.
3. Slide Outer Flange (37), Washer (55) and Screw (38).
NOTE: This screw has left-hand threads. Turn
counterclockwise to fasten.
Spindle
(41)
Outer
Flange (37)
Inner
Flange (33)
Washer (55)
Screw
(38)
Figure 3
Arbor
Bushing (34)
Blade
(not included)
6. For safety purposes, the blade should be adjusted to
just slightly deeper than the material’s thickness.
Figure 1
Page 8
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slowly slide Tile Saw forward, beginning to cut. See
Figure 4, below.
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning
of this manual including all text
under subheadings therein before
set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM
ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and
unplug the tool from its electrical outlet before
adjusting tool or installing accessories.
1. (Explain how to adjust all the tool’s settings, install
and change accessories along with proper accessory
use, and test the tool on scrap work pieces)
Figure 4
WARNING! If cutting into tile that is 3/4” or
thicker, you will need to make two separate cuts.
This will help prevent wear on the motor.
Work Piece and Work Area Set Up
1. Designate a work area that is clean and well-
lit. The work area must not allow access by
children or pets to prevent distraction and injury.
6. For continuous operation, press the Power
Switch and then press the trigger lock switch
on the side of the handle. Press trigger lock
switch again to release the trigger lock.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
7. Release Power Switch to turn off Tile Saw.
8. To prevent accidents, turn off the tool and disconnect
its power supply after use. Clean, then store the tool
indoors out of children’s reach.
3. Secure loose work pieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
General Operating Instructions
1. Make sure that depth adjustment
knob is tight before operation.
2. Set front end of the Base Plate (47) down against
the tile surface without the blade touching the saw.
3. Press the Power Switch (4) to turn on Tile Saw.
4. Allow Tile Saw to reach full speed before beginning
to cut.
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Servicing
Procedures not specifically explained
in this manual must be performed
only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM
ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the
tool from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal
noise or vibration occurs, have the problem
corrected before further use.
Cleaning, Maintenance,
and Lubrication
1. BEFORE EACH USE, inspect general condition
of tool. Check for loose screws, misalignment or
binding of moving parts, cracked, bent or broken
parts, damaged electrical wiring, and any other
condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. After regular intensive use, the Carbon Brushes (22)
may need to be replaced. NOTE: The Tile Saw’s motor
will not function once the Carbon Brushes
wears down.
4. To replace the Carbon Brush (22):
a. Use a screwdriver to open Carbon
Brush Covers (21).
b. Then remove the Carbon Brushes Holder
(8) and slide out Carbon Brush.
c. Replace with new Carbon Brush, slide
Carbon Brush Holder back into housing,
and replace Carbon Brush Cover.
5.
WARNING! If supply cord of power
tool is damaged, it must be replaced only
by a qualified service technician.
Page 10
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Tool will not start.
Possible Causes
1. Cord not connected.
Likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity
for tool and circuit has no other loads.
3. Internal damage or wear. (Carbon
brushes or switch, for example.)
Power being reduced by long or
small diameter extension cord.
3. Have technician service tool.
Tool operates slowly.
Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
1. Keep blade sharp. Replace as needed.
Performance
1. Blade dull or damaged.
decreases over time.
2. Carbon brushes worn or damaged. 2. Have qualified technician replace brushes.
Excessive noise
or rattling.
Overheating.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
1. Forcing tool to work too fast.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Blade misaligned.
2. Check and correct blade to fence alignment.
3. Keep blade sharp. Replace as needed.
3. Blade dull or damaged.
4. Blocked motor housing vents.
4. Wear ANSI-approved safety goggles and NIOSH-
approved dust mask/respirator while blowing
dust out of motor using compressed air.
5. Motor being strained by long or
small diameter extension cord.
5. Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the tool. Disconect power supply
before service.
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Part
Description
Qty.
1
4
1
1
3
1
2
1
Part
Description
Qty.
1
1
4
1
1
1
1
1
1
2
4
5
6
7
8
9
Cable
26 Bearing Sleeve
Screw (ST4.2X19)
Power Switch
Switch Cover
Spring Plate Washer (M5X40)
Rating Label
Carbon Brush Holder
Handle Cover
28 Protection Cover
30 Spring Plate Cross Washer (M4X30)
31 Bearing Anchor Plate
32 O-Ring (18X2)
33 Inner Flange
34 Arbor Bushing
35 Plate Washer
10 Cable Anchor
1
2
1
1
1
1
1
1
2
1
1
2
2
1
36 O-Ring (26X2)
37 Outer Flange
38 Locking Bolt (M6X17)
39 Locking Spring (M8)
40 Half Round Key (4X13)
41 Spindle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11 Screw (ST4.2X16)
12 Cable Protection Sleeve
13 Small Gear
14 Blocking Ring
15 Ball Bearing (629)
16 Half Round Key (3X10)
17 Rotator
18 Screw (ST4.8X63)
19 Insulation Cushion
20 Ball Bearing (608)
21 Carbon Brush Cover
22 Carbon Brush
23 Gear Box
42 Socket
43 Ball Bearing (6201)
44 Locking Spring (M12)
45 Big Gear
46 Needle Bearing
47 Base Plate
48 Wing Bolt (M6X25)
54 Spring Key
24 Housing
1
55 Washer
1
25 Stator
1
Page 12
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Assembly Diagram
Assembly Diagram
34
55
SKU 68298
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship
for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Page 14
For technical questions, please call 1-800-444-3353.
SKU 68298
Download from Www.Somanuals.com. All Manuals Search And Download.
|