HEAVY DUTY
HAMMER TACKER
91670
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No
portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written consent of
Harbor Freight Tools.
For technical questions and replacement parts,
please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
When loading staples, always adhere to all the instructions and
safety warnings provided in this manual. Reminder: Avoid injuries
from sharp staples when loading and cleaning this product.
Be sure material will accept staples. Always test the material to
see if the staples will hold the material you want to secure. Staples
will not hold stone, rock or metal. Best suited for roofing installation,
carpet installation, poly sheeting and upholstery.
Note: The Hammer Tacker is only to be used to strike the material to be
secured. Do not use for any other purpose.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be
supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included
that are listed on Page 5. If any parts are missing or broken, please call
Harbor Freight Tools at the number on the cover of this manual.
Assembly Instructions
1.
You must first load staples (not included) into the Hammer Tacker.
Press the Staple Feeder Button (1) by squeezing the sides together.
While squeezing, push inward and downward to unlock the Staple
Spring Feeder (2). See Figures A & B.
Handle (3)
Staple
Loading Area
Staples Exit
Feeder
Button
(1)
Figure A
REV 06/04
SKU 91670 For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Pull out the Staple Spring Feeder (2). Set aside. Insert a strip of
staples (not included, see Page 2 for size). Place staples in the track
of the loading area. Slide the Staple Spring Feeder (2) back into the
Hammer Tacker. Squeeze and push the Spring Feeder Button (1)
upward to lock it into position. If Spring Feeder will not go all the way
back into place, remove some staples from the magazine.
See Figures A, B &C .
Staple Feeder Button (1)
Staple Spring Feeder (2)
Figure B
Figure C
Operation
1.
To use the Hammer Tacker for roofing, carpeting, poly sheeting or
upholstery, hold Handle (3) like you would a hammer and hit the area
you wish the staple to hold. Avoid hitting your fingers or other body
parts.Test first on a scrap-piece of material to make sure the Hammer
Tacker is working properly and that the staples are fully driven into the
workpiece. Always wear ANSI approved impact safety goggles when
using this product.
Maintenance
1.
2.
Store indoors, and keep dry to avoid rusting.
If Hammer Tacker becomes jammed with staples, use needle nose
pliers (not included) and remove bent or jammed staples.Always wear
ANSI approved safety goggles when removing jammed staples.
Repeat loading instructions on Page 3.Test on scrap material to see if
Hammer Tacker will work correctly after this repair. See Figure E.
Needle Nose Plier
Figure E
SKU 91670 For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: No replacement parts are available.
Staple
Spring
Feeder
Staple
Feeder
Button
Staple Exit
Handle
Staple Loading Area
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND
TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERE TO, OR ARISING OUT OF
HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERE TO.
NOTE: Some parts are listed and shown for illustration purposes only and are
not available individually as replacement parts.
SKU 91670 For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
|