GRAVITY SPRAY GUN
HOLDER
91603
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
Copyright © 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When unpacking, check to make sure the following parts are included that are listed
on Page 4.If any parts are missing or broken, please call Harbor FreightTools at the
number on the cover of this manual.
Assembly and Usage Instructions
The Gravity Spray Gun Holder holds most cup style GRAVITY FEED spray guns.
1. At one end of the Steel Rod (4), attach Ring Holder (3) using a Washer (2) on
each side of the Ring Holder and Tighten with Nut (1).This Ring Holder is used
to hold a strainer (not included) as an aid when filling the spray gun cup with
paint.
2. Attach the other end of the Steel Rod (4) through the Holding Bracket (6) using
Washers (2) and Nuts (1). Attach Base (7) to the Holding Bracket (6) using
Bolts (5), Washers (2), and Nuts (1). See Figures 1 and 2.
3. Your spray gun will rest on the Holding Bracket (6) as needed. Be careful not
to tip or bump the holder as it may fall.
IMPORTANT:
Refer to the manual of the paint spray gun and paint you will use
for necessary warnings and instructions before use.
Ring Holder (3)
Holding
Bracket (6)
Steel Rod (4)
Base (7)
Washer (2)
Holding
Bracket (6)
Bolt (5)
.
Figures 1
Figures 2
Maintenance
1.
2.
Keep indoors to avoid rust.
Wipe surfaces with a damp cloth or paint thinner, depending on what type paint was
used.Rinse off and dry thoroughly.Use Caution: Paint thinner is flammable and must be
disposed of and stored properly.
For technical questions, please call 1-800-444-3353.
SKU 91603 Download from Www.Somanuals.com. All Manuals Search And DownPloaadg.e 3
Parts List
PART #
DESCRIPTION
QTY
Nut
1
2
3
4
5
6
7
4
8
1
1
2
1
1
Washer
Ring Holder
Steel Rod
Bolt
Holding Bracket
Base
Part 1
Part 2
Part 3
Parts Illustration
Part 4
Part 1
Part 6
Part 5
Part 7
Part 1
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as
replacement parts.
For technical questions, please call 1-800-444-3353.
SKU 91603 Download from Www.Somanuals.com. All Manuals Search And DownPloaadg.e 4
|