COIL SIDING NAILER
WITH MAGNESIUM BODY
Model 93257
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair.
7.
8.
Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines or air hoses.
Use eye and ear protection. Always wear ANSI-approved impact safety
goggles and appropriate hearing protection. Wear a full face shield if you
are producing metal filings or wood chips. Wear a NIOSH-approved dust
mask or respirator when working around metal, wood, and chemical dusts
and mists. Other people in the work area must also wear ANSI-approved
impact safety goggles.
9.
Maintain tools with care. Keep tools clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords
and air hoses periodically and, if damaged, have them repaired by an authorized
technician. The handle must be kept clean, dry, and free from oil and grease at
all times. Do not operate a tool if any portion of the tool’s operating controls are
inoperable, disconnected, altered, or not working properly.
10.
Disconnect air hose and release any built-up air pressure. Never service the
Nailer, clear jams, or disassemble with the air hose attached. Always release
any built-up air even after disconnecting hose. Disconnect the Nailer when not
in use.
11.
12.
Remove adjusting wrenches. Check that adjusting wrenches are removed
from the tool or machine work surface before attaching to an air source.
Avoid unintentional starting. Be sure the trigger is in the OFF position when not
in use and before plugging in. Do not carry any tool with your finger on the trigger,
whether it is attached to an air source or not. Do not point the tool towards
yourself or anyone whether it contains nails or not.
13.
14.
Stay alert. Watch what you are doing. Use common sense. Do not operate any
tool when you are tired.
Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts, any broken parts or mounting fixtures, and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired or
replaced by a qualified technician. Do not use the tool if the trigger does not
operate properly.
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
16.
Guard against electric shock. Prevent body contact with grounded surfaces
such as pipes, radiators, ranges, and refrigerator enclosures.
Replacement parts and accessories. This product is to be repaired and
serviced only by a qualified technician. When this product is serviced, only
identical replacement parts should be used. Use of any other parts will void the
warranty. Only use accessories intended for use with this tool. Approved
accessories are available from Harbor Freight Tools.
17.
18.
Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes
are impaired while taking drugs. If there is any doubt, do not operate the tool.
Use proper size and type extension cord. If an extension cord is required, it
must be of the proper size and type to supply the correct current to the compressor
without heating up. Otherwise, the extension cord could melt and catch fire, or
cause electrical damage to the tool. Check your air compressor’s manual for the
appropriate size cord. It is also possible that the use of an extension cord may
cause your circuit breaker to trip or your panel fuse to break. If this happens,
either use a longer air hose, use the compressor without an extension cord, or
find a larger amperage circuit to use.
19.
Maintenance. The maintenance outlined in the “Maintenance” section should be
performed regularly. For your safety, this product should be serviced or repaired
regularly only by a qualified technician.
20.
21.
Compressed air only. Never use combustible gas as a power source.
Do not load nails with the trigger or safety depressed. Unintentional
firing may occur. Do not load nails when the air hose is connected to the
tool. Always assume the tool contains nails.
22.
23.
Disconnect air supply before loading the Nailer. Before reloading (or making
any adjustments to) the Nailer, make sure the compressed air is disconnected.
Fire nails into an appropriate work surface only. Do not attempt to fire nails
into surfaces too hard to penetrate. Do not drive nails on top of other nails, or at
too steep an angle. Nails can ricochet, causing personal injury. Never fire the
Nailer into the air, or point it toward yourself or another person. Always wear
ANSI-approved impact safety goggles during use, maintenance, and reloading.
24.
Do not fire nails too close to the edge of a workpiece. They may split the
workpiece and fly free, causing personal injury.
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
25.
Take caution, as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When nailing these materials
extra care should be taken to avoid inhalation and minimize skin contact.
WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contain chemicals known (to the State of
California) to cause cancer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
* Lead from lead-based paints,
* Crystalline silica from bricks, cement, and other masonry products,
* Arsenic and chromium from chemically treated lumber.
(California Health & Safety Code 25249.5, et seq.)
26.
27.
Stay within air pressure capacity. Never operate the Nailer above 125 PSI.
Hold tool away from head and body. During operation the Nailer may kick
back, causing injury.
28.
Transport Nailer safely. Always disconnect air supply when moving the tool in
the workplace. Carry the tool by the handle to avoid contact with the trigger.
29.
30.
Avoid working alone. If an accident happens, an assistant can bring help.
Note: Performance of the compressor (if powered by line voltage) may vary
depending on variations in local line voltage. Extension cord usage may also
affect the tool performance.
31.
WARNING: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the
operator.
UNPACKING
When unpacking, check to make sure that all accessories listed on page 13 are
included, and the product is intact and undamaged. If any parts are missing or broken,
please call Harbor Freight Tools at the number shown on the cover of this manual as
soon as possible.
Rev 11/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
For best service, you should incorporate an oiler, regulator, and inline filter, as
shown in the diagram below. Hoses, couplers, oilers, regulators, and filters are all
available at Harbor Freight Tools. NOTE: If an automatic oiler is not used, for
smoother operation and to extend the life-span of the tool, put 3-5 drops of
pneumatic Tool Oil (93) in the attached Air Plug (82-not included) before each
use.
QUICK
CONNECTOR
AIR
HOSE
QUICK
CONNECTOR
OILER
FILTER
AIR
COMPRESSOR
QUICK
COUPLER
QUICK
COUPLER
NAILER
REGULATOR
FIGURE A
CONNECTION TO AIR SUPPLY
TESTING THE FULL SEQUENTIAL SAFETY TRIP MECHANISM
WARNING: Even though the Nailer should be empty during this
procedure, ALWAYS point the Nailer at a piece of scrap wood when testing.
1.
2.
Make sure the tool is disconnected from its air supply.
Completely empty the Magazine (85) of Nails. Then, close the Magazine.
(See Figure B.)
FIGURE B
TRIGGER
(60)
AIR PLUG
(82-not included)
MAGAZINE
(85)
SAFETY
(38)
REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Connect the air supply to the tool at the Air Plug (82-not included). Set the regula-
tor at the recommended 70 to 125 operating PSI. Do not exceed the maximum
125 PSI.
Test the tool by depressing the Safety (38) against a piece of scrap wood without
pulling the Trigger (60). The tool must not cycle (fire). If it cycles (fires), stop
immediately and have it repaired by a qualified service technician.
(See Figure B.)
5.
6.
Hold the tool away or off the workpiece. The Safety (38) of the tool should return
to its original position. Squeeze the Trigger (60). The tool should not cycle
(fire). If the tool cycles (fires), stop immediately and have it repaired by a qualified
service technician. (See Figure B.)
Depress the Safety (38) against the workpiece and squeeze the Trigger (60). The
tool must cycle (fire) only once. Release the Trigger and squeeze it again. The
tool must not cycle (fire). With the Trigger held, carefully lift the Nailer and press
it against the scrap wood again. The tool must not cycle (fire). If it fails to
perform in the manner explained in bold, have it repaired by a qualified service
technician. (See Figure B.)
LOADING COIL NAILS
WARNING: Always wear ANSI approved impact safety goggles when
reloading or performing any other maintenance on this tool. Other people
in the work area must also wear ANSI approved impact safety goggles.
WARNING! Make sure the Nailer is not attached to the air hose when
loading the tool.
1.
To open the Magazine Cover (91), press down on the Latch (57) and swing the
Door (32) open. Then, swing the Magazine Cover open. (See Figure C.)
MAGAZINE COVER
(91)
LATCH
(57)
FIGURE C
DOOR
(32)
Rev 11/06; REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Check the Nail Support (88) inside the Magazine (85). The Nail Support can be
adjusted up and down to use various lengths of nails from 1-1/4” to 2-1/8”:
(See Figure D.)
A. 1-1/4” Long Nails (Turn Magazine Post (87) to top setting).
B. Between 1-1/4” and 2-1/8” Long Nails (Use middle setting).
C. 2-1/8” Long Nails (Use bottom setting).
MAGAZINE POST
(87)
(TURN TO ADJUST HEIGHT)
MAGAZINE COVER
(91)
DOOR
(32)
NAILS
(NOT INCLUDED)
NAIL SUPPORT
(88)
FIGURE D
FEED PAWL
(42)
3.
4.
Place a coil of Nails (not included) around the Nail Support (88) in the
Magazine (85). (See Figure D.)
Uncoil enough Nails to reach the Feed Pawl (42). Place the second Nail on the
coil between the teeth of the Feed Pawl, making sure the Nail head fits in the slot
in the upper portion of the Feed Pawl. (See Figure D.)
5.
Swing the Magazine Cover (91) closed. Then, close the Door (32). Make sure
the Door closes securely. If it does not engage, the Nail head is not in the slot in
the upper portion of the Feed Pawl (42). (See Figure D.)
OPERATING THE NAILER
1.
2.
Attach the Nailer to the air supply at the Air Plug (82-not included). Start your
compressor and check the pressure, making sure it is set at the recommended 70
to 125 PSI. Do not exceed the maximum 125 PSI.
Rotate the Exhaust Cover (2) so that the exhaust air blast will be directed away
from the operator. (See Figure E, next page
Rev 11/06; REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
To fire, place the Safety (38) of the Nailer on the workpiece. The Nailer should
not fire if the Safety is not depressed. Once depressed, gently and briefly
squeeze the Trigger (60) once. Do not fire repeatedly. Nails could bounce off
of one another, damaging the workpiece or causing personal injury.
(See Figure E.)
4.
5.
Do not press the Safety (38) against the workpiece with extra force. Allow the
tool to do the work. Always allow the tool to recoil off the work surface.
(See Figure E.)
When finished using the Nailer, always disconnect the tool from its air supply.
Empty the Magazine (85) completely of nails. Attempt to fire the Nailer into a
piece of scrap wood to ensure it is disconnected and is incapable of firing any
nails. (See Figure E.)
6.
Make sure to store the Nailer in a clean, dry, safe location out of reach of children.
EXHAUST COVER
FIGURE E
(2)
TRIGGER
(60)
AIR PLUG
(82-not included)
MAGAZINE
(85)
SAFETY
(38)
REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Anytime any maintenance or repairs are done (including clearing jams), FIRST:
1.
Disconnect the Nailer from its air supply.
Empty the Magazine (85) completely.
2.
3.
Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any Nails.
CLEARING JAMS
1.
Occasionally, a Nail may become jammed in the firing mechanism of the Nailer,
making the tool inoperable.
2.
To remove a jammed Nail, disconnect the Nailer from its air supply. Empty the
Magazine (85) completely of Nails. Attempt to fire the Nailer into a piece of scrap
wood to ensure it is disconnected and is incapable of firing any Nails.
3.
4.
5.
Use a pair of needle nose pliers to remove the jammed Nail (usually in the Feed
Pawl (42) area.
Replace the coil of nails into the Nailer. Close the Magazine Cover (91) and Door
(32) securely. Then, reconnect the air supply hose to the Nailer.
Press the Safety (38) against a piece of scrap wood, and test fire the Nailer
several times while checking for proper operation. If the Nailer is properly firing,
you may continue using the tool. If the tool fails to perform properly, immediately
discontinue use and have the tool repaired by a qualified service technician.
6.
When finished working, disconnect the air supply. Remove the nails. Then, store
the Nailer in a clean, dry, safe location out of reach of children.
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Anytime any maintenance or repairs are done, FIRST:
Disconnect the Nailer from its air supply.
1.
2.
3.
Empty the Magazine (85) completely.
Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any Nails.
INSPECTION, MAINTENANCE, AND CLEANING
1.
Inspect the Nailer frequently and lubricate periodically with pneumatic Tool Oil
(93). Then, wipe dry. Do not use detergent oil or additives as these lubricants will
cause accelerated wear to the internal seals. Use the included Hex Wrench (94)
to ensure bolts are properly tightened; only a qualified technician should open the
Nailer to repair internal parts.
2.
Inspect the Filter Unit (80) before each use and clean or replace as necessary.
Dirt and water in the Filter Unit are major causes of pneumatic tool wear. Use an
oiler/filter in the compressed air system for better performance and longer tool life.
The filter must have adequate flow capacity for the specific application.
(See Assy. Diagram.)
3.
Clean the external parts of the Nailer with a clean cloth and mild detergent or
nonflammable solvent. Then, dry.
4.
5.
Store the tool in a clean, dry, safe location out of reach of children.
WARNING: All maintenance, service, or repairs not listed in this manual
are only to be attempted by a qualified service technician.
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Trigger Valve leaks air
Nose leaks air
Possible Cause
Corrective Action
Replace O-Ring
Replace O-Ring or Gasket
O-Ring cut or cracked
O-Ring or Gasket is cut
or cracked
Bumper cracked or worn
Air supply restricted
Replace Bumper
Check air supply equipment
Failure to cycle (fire)
Tool dry. Lack of lubrication
Use Air Tool Oil
Broken Cylinder Cap Spring
Air pressure too low
Broken Cylinder Cap Spring
Replace Cylinder Cap Spring
Check air supply equipment
Replace Cylinder Cap Spring
Lack of power
Slow to cycle (fire)
O-Rings/Seals cut or cracked Replace O-Rings/Seals
Exhaust blocked
Check Bumper & Head Valve Spring
Tool dry, lack of lubrication
Bent nails
Use Air Tool Oil
Replace with new nails
Nails jam in tool
Broken/chipped Driver
Wrong size/type nail
Replace Driver
Replace with correct size/type nail
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS, AND NOT BYTHE BUYER. THE BUYER
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTSTHERETO.
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Part #
1
Description
Part #
Description
Spring
Screw
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
93
94
A1
A2
2
3
4
5
6
7
8
9
Exhaust Cover
Screw
Elastic Washer
Cylinder Cap (Magnesium)
Gasket
Head Cap
Ring
Compression Spring
O-Ring
O-Ring
Head Valve
Gasket
Screw
Washer
Spring
Spring Guide
Piston Stopper
Cover
Clip
Pin
Spring
Latch
O-Ring
Pin
Trigger (A)
Receiver
Trigger (B)
Pin
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
O-Ring
Pin
Piston Head
Driver Rod
Clip
Cylinder Ring
O-Ring
Cylinder
Ring
O-Ring
Body (Magnesium)
O-Ring
Bumper
Pin Guide
Spring
Feed Pawl (B)
Pin
Door
Screw
Nose (Bottom Plate)
Pin Guide
Cover
Pin
Safety
Spring
Screw
Grip Handle
Trigger Cover
Trigger Plunger
O-Ring
Spring
O-Ring
Valve Bushing
O-Ring
O-Ring
Pin
Trigger Valve
O-Ring
O-Ring
Screw
Clip
Filter Unit
End Cap
Air Plug (not included)
Retainer
Pin
Magazine
Receiver (B)
Magazine Post
Nail Support
Spring
Receiver (A)
Magazine Cover
Tool Oil
Hex Wrench
Control Air Valve
Main Piston Unit
Screw
Feed Pawl (A)
Pin
Spring
Pin
Feed Piston
O-Ring
O-Ring
REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
#82 Air Plug (not
included)
#93 Tool Oil
#94 Hex Wrench
Not Shown
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
REV 12/06
SKU 93257
For technical questions, please call 1-800-444-3353
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|