9” HID OFF-ROAD LIGHT
95059
INSTALLATION AND OpeRATION INSTRucTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
9.
use only with vehicles with 12 volt Dc electrical systems.
Turn vehicle ignition off before making cable connections. Vehicle’s engine must be
cooled down before making cable connections.
10.
11.
12.
Disconnect the battery cables before installing Off Road lights or changing bulbs.
Such preventive safety measures reduce the risk of accident.
Keep automotive accessory maintained and clean. Do not use a damaged automotive
accessory. Tag damaged automotive accessories “Do not use” until repaired.
Avoid contact with Battery Acid. If splashed, immediately wash affected area with clean
water and baking soda for at least 15 minutes. If irritation persists get medical help im-
mediately.
13.
connect Off Road Light cables to proper polarities. Connect black cable to the negative
battery terminal, and the red cable to the positive battery terminal (For a negative grounded
system). Failure to do so could result in sparks, possible fire and severe personal injury.
14.
15.
Keep cables clear of fan blades, belts, pulleys, and other moving parts of the engine
that may cause injury, or damage to the Off Road Light.
Do not allow the Black and Red battery cables or terminals to touch. Failure to adhere
to these directions could result in severe personal injury. If this happens, sparks will occur
that can melt connection lugs, or other metal objects, and create the potential for fire.
16.
17.
18.
19.
Read all instructions and warnings on any battery or automotive electrical systems
before working on vehicle.
Do not expose the battery or bare wires, switches or connections to rain or wet
conditions.
To avoid damage of cable and plug, never pull the cable to disconnect the Fog
Lights.
Always unplug the Off Road Light from their electrical connection and allow to
cool completely before performing any inspection, maintenance, or cleaning pro-
cedures.
20.
21.
Repairs should be carried out only by a qualified technician.
An appropriate in-line switch and fuse are essential to help prevent fire in the event
of a short circuit. These components are not included in this kit and will need to be pro-
vided by the customer.
22.
23.
This product contains or, when used, produces a chemical known to the State of
california to cause cancer and birth defects or other reproductive harm. (California
Health & Safety Code § 25249.5, et seq.)
HID lamps emit ultraviolet, visible, and infrared radiation. HID bulbs operate at very high
temperatures and pressures. Possible skin or eye irritation can result from exposures
exceeding 15 minutes. Do not stare at exposed lamp in operation. During operation, the
bulb should be enclosed in a housing to prevent injury. Do not remove bulb from equip-
ment until it has cooled completely. Never handle the bulb when it is operating or until it
has cooled!
SKU 95059
For technical questions, please call 1-800-444-3353
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
About High Intensity Discharge (HID) Lamps
High Intensity Discharge (HID) lamps use a gas capsule rather than a filament inside the bulb. Light
is created by an electrical arc between two electrodes sealed in the bulb. A ballast is required to
provide the proper voltage and maintain current control. HID bulbs create more light than a com-
parable halogen lamp, and the light is closer in color to natural daylight than halogen light.
In HID lamps, the light is produced by creating an electrical arc in a metal vapor. Free electrons
colliding with an atom in the vapor momentarily knock an electron into a higher orbit of the atom.
When the displaced electron falls back to its former level, a quantum of radiation is emitted. The
wavelength of light produced depends on the shell level of the disturbed electron and on the ele-
ment and ionization of the metal vapor used in the arc tube.
Although producing only 5% of its output when first ignited, after a few seconds the HID lamp will
come up to full output. Also, if power to the lamp is lost or turned off, the arc tube must cool before
the arc can be restruck and light produced.
HID lighting has several advantages over conventional halogen lights:
• More light output. An HID light source produces light at approximately three to five times
halogen’s efficiency. Efficiency is measured in lumens per watt, a measure of the amount of
light produced for a given amount of electrical consumption. An HID lamp’s lumens per watt
(LPW) efficiency is roughly six to eight times that of an incandescent lamp.
• Brighter light. The color of HID lighting is closer to natural daylight than halogen or incan-
descent light, which appear yellowish in comparison. Florescent light appears more green
than natural daylight. Light color is described in degrees Kelvin. Typical color temperatures
are 2800K (incandescent), 3000K (halogen), 4100K (cool white or SP41 fluorescent), and
5000K (daylight-simulating fluorescent colors). HID lights produce a light with a color tem-
perature at or above 5000K. Higher temperature lights appear brighter and bluer than lower
temperature lights.
• Longer Service Life. An HID lamp will last, on the average, 3 to 5 times as long as a halogen
bulb. In normal use, your HID bulb should last more than one thousand ignitions.
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools at: 1-800-444-3353
Package should include: (1) 9” HID Off-Road Light, (1) Wiring Harness, (1) manual.
Bulb Replacement
To replace the bulb, remove the two screws (one on each
Screw
side), that hold the lens cover on. See illustration to the
left. Next remove the old bulb and replace it. Replace the
Lens Cover using the same screws.
WARNING: Never touch the bulb with your bare hands.
Oil from your fingers will damage bulb.
SKU 95059
For technical questions, please call 1-800-444-3353
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Warning: Before Installation, disconnect negative battery cable then disconnect the posi-
tive battery cable, in that order.
Warning: Whenever drilling, be sure that the drill will not damage any wires, tubes or com-
ponents on either side of the member being drilled. plan for your installation so units will
be located conveniently and wires will be routed out of the way of any other components.
plan to fill all drilled holes with sealant to prevent water intrusion or rust.
1.
Lamp Installation: Fasten the Off Road Light to your vehicle. Adjust angle of lamp as
desired. Connect the ground wire from the light to a clean grounded piece of metal on the
vehicle frame.
2.
Install switch (not included) in passenger compartment. Connect the blue wire (with
inline 5A fuse holder) to the switch and to the positive battery terminal. Attach one appro-
priately-sized red wire to the switch. Carefully route two more wires from the other positive
terminal on the switch to the lights. See the diagram below.
WARNING: Do not damage any cables, hoses or components when installing any com-
ponent of this kit. Take care not to route wires where they may get tangled, pinched, cut,
burned or otherwise damaged by the operation of the engine or movement of the car.
1.
Connect positive wires from the light switches to the lights.
cAuTION: Do not reverse polarity, as that will damage unit.
1.
2.
Reconnect the vehicle positive battery cable. Test lights.
Be sure the Off-Road Lights, ballasts and switch are firmly attached and will not come loose
during normal driving or a sudden stop.
3.
Periodically check the Off-road Lights to be sure they remain in place. Make any adjust-
ments as needed.
Black Wire connects
to negative (-) vehicle
battery terminal
Switch
(not included)
Red Wire
Red Wire
Blue wire
Connect to
Positive (+)
Vehicle battery
Terminal
5A Fuse
Black Wire
Connects to
ground (-)
Operation
1.
With the vehicle running, turn on the HID Light using the Switch (not included).
SKU 95059
For technical questions, please call 1-800-444-3353
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
care and Troubleshooting of your HID Lights
cAuTION: The lens of the lamps must be kept clean. The lamps should be handled with care,
giving special attention to bulb.
WARNING: NEVER TOUCH THE BULB WITH YOUR BARE HANDS! The oil from your fingers
will cause the bulb to explode!
1.
2.
Maintain proper electrical wiring polarity to prevent damage to the lamp.
Protect the quartz arc tube when handling the lamp. Keep the arc lamp clean. Do not touch
the quartz tube or the inside surface of the reflector. If tube or reflector are dirty, clean with
rubbing alcohol. Allow to dry completely before lighting.
3.
4.
5.
The bulb and ballast are sensitive to external operating temperature. Do not expose to
extremely high or low ambient temperature.
Periodically clean the lamp by wiping with a lint free towel or swab immersed in denatured
alcohol. Allow to dry completely before lighting.
While HID bulbs last considerably longer than halogen bulbs, several characteristics indicate
that a bulb is approaching the end of its life-span. Initial symptoms of end-of-life include
low light output and/or intermittent starting. Visual signs include blackening at the ends of
the arc tube and electrode tip deterioration. Note that HID bulbs contain metals, including
mercury, that can be harmful to the environment. Please dispose of any HID bulb in ac-
cordance with local, state, and federal regulations.
6.
7.
All lamps have a limited lifespan. However, if you are experiencing problems with your HID
light inspect the following:
Bulbs:
• Inspect for broken arc tube or outer lamp jacket
• Check connection where lamp broken where glass meets the base
• Make a visual inspection of the bulb for broken or loose components in lamp envelope
• Inspect for arc tube end blackening
• Inspect for deposits inside the outer glass envelope
9.
Ballast and capacitor points-of-failure:
•
Attempt ignition a second time after properly resetting the ballast by disconnecting,
waiting 15 seconds, and then reconnecting the connectors attached to the lid.
• Are you using identical replacement lamps?Your ballast will not work with incorrect watt-
age lamps.
• Avoid possible overheat due to ambient temperature
• Inspect for miswiring/pinched wires
• Inspect ballast housing and wiring for mechanical damage
The Bulb is the only replacement part offered. Call 1-800-444-3353 to order the bulb.
SKU 95059
For technical questions, please call 1-800-444-3353
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITeD 90 DAY WARRANTY
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product is free from defects in
materials and workmanship for the period of 90 days from the date of purchase.This warranty does
not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs
or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or
to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you.THIS WARRANTY IS ExPRESSLY IN LIEU
OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with trans-
portation charges prepaid. Proof of purchase date and an explanation of the complaint must
accompany the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily and
quickly provide you with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within the scope of our
warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
REV 08d
SKU 95059
For technical questions, please call 1-800-444-3353
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
|