1/2” AIR IMPACT WRENCH
Model 95310
Assembly and Operating Instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No
portion of this manual or any artwork contained herein may be repro-
duced in any shape or form without the express written consent of
Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do
the work of a larger industrial tool. Do not use a tool for a purpose for which it was not
intended.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips.Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across running machines.
10. Maintain tools with care. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect air hose
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
11. Disconnect air. Unplug when not in use. Do not carry tools by the hose.
12. Avoid unintentional starting. Be sure the switch is in the Off position when not in
use and before plugging in.Do not carry any tool with your finger on the trigger, whether
it is plugged in or not.
13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function.Check for alignment and binding of moving parts;any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified technician.
Do not use the tool if any switch does not turn On and Off properly.
15. Guard against electric shock. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerator enclosures.
16. Replacement parts and accessories. When servicing, use only identical
replacement parts.Use of any other parts will void the warranty.Only use accessories
intended for use with this tool.Approved accessories are available from Harbor Freight
Tools.
17. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
SKU 95310
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When unpacking, check the parts diagram and part number listing on page 6 to
make sure all parts are included. If any parts are missing or damaged, please call
Harbor Freight Tools at the telephone number on the cover of this manual as soon as
possible.
Your Air Impact Wrench comes pre-assembled. To complete preparations for use, follow
the steps shown on the following page. Part numbers shown below identify parts shown
on the part number listing on page 6.
Air Connection
1. Remove the Screen from the Inlet (both included in part 42). You will need an air
hose fitting (sold separately) before you can connect your Impact Wrench to an air
compressor.
2. Attach the air hose fitting to the Inlet and tighten with a wrench.
3. Attach a quick-disconnect coupler (sold separately) to the air hose fitting if desired.
This is a useful accessory as it allows quick-coupling action when using a variety
of tools with the same air compressor.
4. The Impact Wrench is ready for use.
Operation
Frequent but not excessive, lubrication is required for best performance. Oil added
through the airline connection will lubricate internal parts. An automatic airline oiler is
recommended but oil may be added manually before every operation or after about 1 hour
of continuous use. Only a few drops of oil at a time are necessary. Too much oil will collect
inside the tool and be blown out during the exhaust cycle. ONLY USE PNEUMATIC TOOL
OIL. Do not use detergent oil or additives as these lubricants will cause accelerated wear
to the seals in the tool.
Dirt and water in the air supply are major causes of pneumatic tool wear. Use a filter/
oiler for better performance and longer life. The filter must have adequate flow capacity for
the specific application. Consult the manufacturer’s instructions for proper maintenance of
your filter.
The connector on the tool must not hold pressure when the air supply is disconnected.
If the wrong fitting is used, the tool can remain charged with air after being disconnected.
Your Impact Wrench features an air Regulator (37), allowing you to vary the amount of
torque exerted on the nut or bolt you are working on. Setting “1” is the lowest setting, and
is recommended for smaller nuts and bolts. Setting “4” is the highest setting and provides
the most torque and speed.
SKU 95310
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loosening
1. Attach the correct size socket to the Anvil (8).
2. Set the compressor’s pressure regulator to 90 PSI. Do not set the compressor’s
outlet regulator above 90 PSI.
3. Connect the Impact Wrench to the air compressor’s hose. If leaking is detected,
disconnect the air hose and repair before use.
4. Place the socket over the nut to loosen.
5. Grip the Impact Wrench firmly. Press the Reverse Valve (44) in from the area
above the Trigger (29) so that the Reverse Valve protrudes out the back of the
Housing. Press the Trigger to start the Impact Wrench.
Caution:
Make sure the nut or bolt can withstand the Impact Wrench’s working
torque.
6. If the Impact Wrench cannot loosen the nut, DO NOT raise the outlet pressure of
the air compressor.
7. If the Impact Wrench’s Air Regulator is set on a low setting, you may raise the
setting and try again. If the ImpactWrench’s Air Regulator is already set on the “4”
setting, do not continue attempts to loosen the nut with the Impact Wrench. Use
other appropriate tools and methods to loosen the nut.
8. When the nut is removed, stop the Impact Wrench by releasing the Trigger and
remove the ImpactWrench from the nut. Remove the nut from the socket if needed.
Tightening
The working torque of the Impact Wrench is 250 foot/lbs. Make sure the nut or bolt you
are using the Impact Wrench to tighten can withstand the rated torque.
1. Tighten the nut on as far as you can by hand.
2. Place the socket on the nut. Press the Reverse Valve forward so it protrudes out
the front of the Housing. Press the Trigger to start the Impact Wrench.
3. If the Impact Wrench stalls while tightening, DO NOT raise the outlet pressure of
the air compressor above 90 PSI.
4. If the Impact Wrench’s Air Regulator is set on a low setting, it may be raised before
you try again. If the nut will not tighten at the maximum setting, do not continue
attempts to tighten the nut. Use other appropriate tools and methods to tighten the
nut.
SKU 95310
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. When the nut has been tightened, remove the Impact Wrench and socket. Do not
over-tighten.
6. If available, check the recommended torque specifications for the nut. You should
use a torque wrench to torque the nut after using the Impact Wrench.
Maintenance
The Impact Wrench is best operated with an airline oiler. If you are using the Impact
Wrench without an airline oiler, perform the following maintenance:
Disconnect the Impact Wrench from the air hose. Apply a few drops of
pneumatic tool oil through the air line before each use, or every hour if used
continuously. Apply a few drops of oil to the Trigger mechanism. Work the
Trigger a few times to lubricate.
Note: Do not use detergent oil or additives as these lubricants will
cause accelerated wear to the tool’s seals.
WARRANTY
LIMITED 1YEAR
WARRANTY
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly
to misuse, abuse, negligence or accidents; repairs or alterations outside our facilities; or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 95310
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Listing and Parts Diagram
SKU 95310
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
|