WIRELESS HOME ALARM
94799
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Do not overreach. When using a ladder, keep proper footing and balance at
all times.
7. Stay alert. Watch what you are doing, use common sense.
8. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
Note: Performance of this product may vary depending on variations in Sensor and
Main Unit battery power.
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make that all theWireless Home Alarm System components
are included.See photo below. If any parts are missing or broken, please call Harbor
Freight Tools at the number on the cover of this manual.
Adhesive Strips
for Sensors and
Main Unit
Sensors 1 to 6
Magnetic Strip
Main Unit
Remote Controls
and Batteries
(above)
Installation
1. Snap off the back cover of the Main Unit and install three, quality AA batteries
(not supplied) into the Main Unit. Pay attention to the battery polarity
(+ and -). See photo below-left.
SKU 94799
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
2. Unscrew the back cover of each Remote Control and insert the battery
(supplied) into the back of the Remote. Pay attention to the battery polarity
(+ and -). See photo below-right.
Main Unit
Remote Control
Note: Each Sensor comes with a battery installed. Since the internal battery is only
used when the Magnetic Strip is moved away (sensor tripped), it should last two
years. The batteries of the Remote Controls should also last two years.
3. Select the six Sensor locations. They should be placed in the most likely point
of entry, (i.e., doors or windows), or exit points, if used to protect entry to
areas such as to swimming pools.
4. Select an area on the movable part of the door or window where the Sensor
can be mounted flat.The Magnetic Strip must be mounted parallel to, and no
more than 1/4 inch from, the Sensor.The Sensor and Magnetic Strip may be
mounted upside down to accommodate door or window configuration.
Window Frame
Door Frame
Door
Window
Note: It is recommended to test each Sensor with its Magnetic Strip before mounting.
Refer to the Operation section on page 5.
5. Peel off the backing to one of the Adhesive Pads and squarely stick it to the
back of one of the Sensors.
6. Peel off the remaining Adhesive Pad backing and secure the Sensor to its
mounting location.
SKU 94799
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
7. Peel the Adhesive Pad backing from one of the Magnetic Strips and mount it
parallel to, and no more than 1/4 inch from, the Sensor. See photos at the
bottom of page 4.
8. Repeat steps 5 to 7 for each Sensor and Magnetic Strip.
9. Using a small round-head screw (not supplied), screw into the desired
mounting location. Place the hole in the back of the Main Unit over the screw,
and slide the unit down to lock in place.
Note: Not all the Sensors need to be used for the Wireless Home Alarm to work.
Operation
Controls and Indicators
Main Unit
Alarm - Loud noise
when Sensor tripped.
Sensor LED lights
when Sensor tripped.
Off - Unit turned off.
Chime - Ding-dong
sound when Sensor
tripped.
Sensor
Off - Sensor turned off.
RF - Sensor On; No
RF+Alarm - Sensor On;
sound when tripped.
Sensor Sounds when
Sensor # lights on
Main Unit.
tripped. Sensor # lights on
Main Unit.
Setup for Operation
1. On each Sensor, push the slide switch to the desired operating position:
RF+Alarm (signal and sound) or RF (signal, no sound).
2. On the Main Unit, push the slide switch to the desired operating position:
Alarm (loud noise) or Chime (Ding-dong sound).
SKU 94799
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
Arm Alarm System
On the Remote Control, press the ON button.The LED on the Remote Control will
temporarily turn on.This can be done from outside the house or other protected
structure.
Disarm Alarm System
On the Remote Control, press the OFF button.The LED on
the Remote Control will temporarily turn on.This can be
done from outside the house or other protected structure.
Remote Control
Troubleshooting
Problem
Possible Cause
1. Sensor is turned Off.
2. Battery is dead.
Probable Solution
1. Turn Sensor On.
2. Replace battery.
When system is armed,
one sensor does not sound
or signal Main Unit when
Magnet Strip is moved.
3. Main Unit is turned Off. 3. Turn Main Unit On.
One Sensor continues to
sound alarm even through
the door is closed.
Magnetic Strip is placed too
far from Sensor.
Move Magnetic Strip to within
¼” of the Sensor.
Main Unit does not detect
any intrusions from any
Sensors.
1. Main Unit batteries are
dead.
1. Replace batteries.
2. Main Unit is placed too 2. Move Main Unit closer to
far from the Sensors.
the Sensors.
Maintenance
1. Periodically test each Sensor and Main Unit for alarm indication and sound.
2. Periodically test each Remote Control for Main Unit activation and
deactivation.
3. Replace Main Unit batteries at least once a year. Replace other batteries as
required.
SKU 94799
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
Parts List
Item
1.
Description
Main Unit
Qty
1
2.
Sensor
6
3.
4.
5.
6.
Magnetic Strip
Battery, Remote Control
Remote Control
Battery, Sensor
Pads, Adhesive
6
2
2
6
7.
6
Parts Photo
(2)
(2)
(2)
(3)
(3)
(3)
(7)
(1)
(4)
(4)
(5)
(5)
(3)
(3)
(2)
(3)
(2)
(2)
(6) Sensor Battery not shown.
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 94799
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
|