Hamilton Beach Blender Tango Series User Manual

O
zs  
Cu  
ps  
44  
40  
36  
32  
28  
24  
20  
16  
12  
8
1
5
5
4
/
2
Tango Series  
Bar blenders  
Operation Manual  
1
/
2
4
3
/
2
3
2
1
/
2
2
1
1
/
2
1
4
1
/
2
2
1
/
4
840083701-UK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blender Safety  
IMPORTANT SAFETY INSTRUCTIONS  
WARNING – When using electrical appliances, basic safety precautions should be followed, including  
the following:  
Do not use outdoors.  
Read all instructions.  
This appliance is intended for short periods  
of operation, with a rated operating time of  
3 minutes.  
Plug into a grounded outlet.  
Do not touch surfaces that may be hot.  
Use handles or knobs provided.  
To prevent damage to blender, jar, or cutter  
assembly, DO NOT move or shake blender while  
in operation. If blending action stops during  
operation, turn blender OFF, remove jar from  
base, remove jar cover, and use a thin rubber  
spatula to push mixture towards cutters.  
Do not spray the base with a high-pressure  
spray gun.  
Disconnect power before cleaning or servicing.  
To prevent burns from hot liquids splashing out of  
the jar, always remove the filler cap of the  
container cover before blending hot liquids.  
Do not operate any appliance with a damaged  
cord or plug or after the appliance malfunctions,  
or is dropped or damaged in any manner.  
Return appliance to the nearest service facility  
for examination, repair, or electrical or  
mechanical adjustment.  
If the supply cord of this appliance is damaged,  
it must be replaced by the manufacturer or its  
service agent or a similar qualified person. If fitted  
with a non-rewirable U.K. plug, the 13 amp fuse  
approved by ASTA to be B.S. 1362 must be used.  
If you need a replacement fuse carrier, it must be  
replaced by the same colour coded carrier with  
the same markings. Fuse covers and carriers can  
be obtained from approved service agents.  
IMPORTANT: If the molded plug is cut off,  
dispose of it immediately. The plug is not rewirable  
and would cause a shock hazard if inserted into  
a socket.  
Extreme caution must be used when moving an  
appliance containing hot oil or other hot liquids.  
Do not use appliance for other than intended use.  
To protect against electrical shock, do not  
immerse cord, plug, or blender base in water  
or any other liquid.  
Close supervision is necessary when any  
appliance is used by or near children.  
The use of accessory attachments not  
recommended by Hamilton Beach may cause  
injuries.  
To reduce risk of personal injury, unplug cord  
from outlet when not in use, and before putting on  
or taking off parts or doing any other servicing of  
the blender.  
Do not let cord hang over edge of table or  
counter or touch hot surfaces.  
Do not place on or near a hot gas or electric  
burner or in a heated oven.  
To reduce risk of personal injury and to prevent  
damage to blender or jar and cutter assembly,  
DO NOT insert utensils into blender jar while  
operating blender, or store utensils in the blender  
jar when it is not in use.  
Avoid contacting moving parts.  
Blades are sharp. Handle carefully.  
Inspect jar and cutter assembly daily. Check  
cutter for wear, nicks, or broken blades. Replace  
jar and cutter assembly at least every 12 months.  
Do not defeat the jar pad sensors.  
SAVE THESE INSTRUCTIONS –  
Blender Operation – Quick Start Guide  
1. Place the blender on a dry, level surface.  
4. Set the controls to your preference.  
5. Move the power switch to the “on” or I position.  
2. Make sure the power switch is in the “off” or O  
position. Plug the blender into a grounded electrical  
outlet.  
3. Place the jar on the base with ingredients and jar  
lid in place.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts and Features  
The parts and features for the Tango Series Blenders are shown on this page. Become familiar with all parts and  
features before using your blender.  
Your Tango Series blender is designed for blending and mixing beverages.  
NOTE: The Blender is not designed to crush ice. Ice cubes made in most icemakers may be added to liquid  
ingredients in the blender to make daiquiris or similar drinks.  
NOTE: Only use the Hamilton-Beach 91300 blender container (part number 6126-91300, as provided with the unit).  
Removable  
Cover  
Filler Cap  
Container  
Gasket  
Cutter  
Assembly  
Collar  
Blades  
Blender  
Base  
Model 91300  
On (I)/Off (O)/  
Pulse  
Switch  
Low/Hi  
Switch  
Model 1G91300  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Operating the Blender–Model 1G91300  
wWARNING  
wWARNING  
Cut Hazard  
Electrical Shock Hazard  
Plug into a grounded outlet.  
Do not remove ground.  
Do not use an adapter.  
Do not use an extension cord.  
Always place cover on jar when blending.  
Do not put hands, spoons or other utensils  
in jar when blending.  
Failure to follow these instructions can  
result in broken bones, cuts or other injuries.  
Failure to follow these instructions can  
result in death, fire, or electrical shock.  
Controls  
Two separate switches on the front panel allow you  
to control the blender for precise blending  
requirements:  
The On/Off switch will turn the blender On for  
continuous operation or Off.  
On (I) /  
Off (O) /  
Hi/Low  
Pulse  
Switch  
Switch  
The  
Pulse position on the On/Off switch  
(Model 91300 only) turns on the blender only  
when the switch is pressed. When the switch is  
released, the blender will stop. This will allow you  
to precisely control the operation of the blender.  
The Hi/Low switch allows you to select the  
following speeds:  
Model 1G91300  
Hi – 20,000 RPM Low – 18,500 RPM  
3. Plug the blender into an electric outlet.  
4. Place the ingredients to be blended into the  
container.  
5. Place the container onto the base. Make sure it  
rests securely on the base.  
6. Place the cover and filler cap on the container.  
7. Set the Hi/Low switch to the desired speed. See  
“Professional Blending Techniques” for blending  
tips.  
Using the blender  
Before you use the blender for the first time, wash  
the container, cover, and cutter unit assembly.  
Refer to “Cleaning Instructions.” Do not put the  
cutter assembly in the dishwasher.  
To operate the blender, proceed as follows:  
1. Place the blender on a clean, dry, level surface,  
and set the On/Off switch to Off.  
2. Place cutter unit in the threaded collar, blades up.  
Slip the gasket OVER the blades and onto the  
base of the cutter assembly. Screw the  
NOTE: If you want the blender to run for short  
bursts, press the  
pressing the  
Pulse switch. While you are  
Pulse switch, the blender will run at  
completed cutter assembly onto the container.  
the selected speed. Release the Pulse switch to stop  
the blender.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Operation  
wWARNING  
Burn Hazard  
Professional Blending Techniques  
Filling the container  
When filling the container with ingredients, follow  
these recommendations:  
• Use sufficient amount of liquid to ensure that the  
mixture is fluid and free-running at all times. Pour  
the liquid into the container FIRST.  
• Cut solid ingredients into pieces that are no  
bigger than a 1(2.5cm)cube.  
• Add the ingredients to container in batches. Do not  
blend maximum volume all at once.  
• Do NOT overfill the container with product. This  
may prevent the blender from processing the  
product properly. Process dense foods or thick  
mixtures in small batches, and remember that the  
volume of the product normally increases during  
processing.  
• Do not exceed one quart of content when  
blending hot product.  
• Always place the cover and filler cap on the  
container when blending. For blending hot  
liquids, remove filler cap from container cover  
before blending.  
Always use caution when blending  
hot contents.  
Failure to follow these instructions  
can result in burns.  
Blending hot mixtures  
IMPORTANT: To minimize the possibility of  
scalding, the following precautions MUST be  
observed:  
• Do not exceed 1 quart of content when blending  
hot product. Remember that the volume of the  
product normally increases during processing.  
• Always place the cover on the container and  
remove the filler cap from container cover when  
blending hot liquids to prevent the build up of  
pressure.  
Blending techniques  
Icy drinks – Do not use blender to crush large ice  
cubes. The blender is not designed for this. Small  
ice cubes or crushed ice is recommended. Pour in  
liquid, then add ice. Cover. Set speed at HIGH and  
process until desired consistency is reached.  
Chunks of frozen fruit can be added to milk or fruit  
juice to produce a sherbet or slush.  
• Never stand with your face directly over the  
container when operating the blender where  
steam may be released.  
• Begin on LOW speed and then select a speed  
that produces a column of air in the center of  
the container.  
Filler Cap  
Use the filler cap to add liquids to the container  
while the unit is running.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the Blender  
Cleaning Instructions  
wWARNING  
wWARNING  
Cut Hazard  
Electrical Shock Hazard  
Plug into a grounded outlet.  
Do not remove ground.  
Always place cover on jar when blending.  
Do not put hands, spoons or other utensils  
in jar when blending.  
Do not use an adapter.  
Failure to follow these instructions can  
result in broken bones or cuts.  
Do not use an extension cord.  
Do not immerse base in water or  
other liquid.  
Failure to follow these instructions can  
result in death, fire, or electrical shock.  
Sanitizing  
1. Wash container as instructed in “General  
Cleaning.”  
General cleaning  
2. Fill container with sanitizing solution (See  
“Recommended Sanitizing Solution” below)  
and place on base.  
Do not allow food residue to dry on any part of the  
blender. Wash and rinse container, cutter unit  
assembly and base after each use, or whenever it  
will not be used again within one hour, as follows:  
3. Replace cover and filler cap and run on LOW  
speed for 2 minutes. Empty container.  
1. Remove the container from the base, and then  
remove the cover. Add cleaning solution to the  
container. Use a washing solution of hot water  
(less than 115° F/46° C) and a non-sudsing  
detergent. Use the recommended amount of  
detergent.  
2. Scrub and flush out the container interior,  
cover and filler cap to remove food residue.  
Empty container.  
4. Wipe the container exterior with a soft cloth or  
sponge dampened with sanitizing solution.  
5. Immerse the cover and filler cap in sanitizing  
solution for two minutes.  
6. Remove any remaining moisture from cutter  
assembly by replacing container on base with  
cover and filler cap in place. Then run blender  
on HiGH speed for a minimum of 2 minutes.  
3. Fill container 14 full with fresh washing solution  
and place it on the base.  
7. To dry, place empty container on base and  
run on HIGH speed for two seconds.  
4. Replace the cover on the container and run the  
8. When ready to use, rinse with clean water.  
blender on high speed for 2 minutes.  
NOTE: Do not rinse container, cover or filler cap  
after sanitizing.  
5. Repeat step 3 using clean rinse water  
(95° F/35° C).  
Recommended Sanitizing Solution:  
6. Wipe down the container, filler cap, and cover  
with a soft cloth or sponge, dampened with fresh  
washing solution.  
7. Wipe the exterior of the base with a damp cloth  
or sponge. The base contains electrical  
components: do not immerse, use a  
high-pressure washer, or use a dishwasher  
to clean the base.  
The sanitizing solution should consist of 1  
tablespoon of household bleach per 1 gallon of  
clean, cool water (60° F, 16° C) mixed according  
to the instructions on the bleach. When using a  
sanitizing solution other than that recommended,  
the sanitizing solution concentration should be  
tested using commercially available test strips  
and should indicate a concentration between  
100 and 200 parts per million of bleach to water.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the Blender  
Troubleshooting Guide  
Problem . . .  
Solution . . .  
• Check to see if unit is securely plugged into an electric outlet.  
Blender fails to start  
or stops while it is  
running and cannot  
be restarted  
• Check to see if the fuse for the electric outlet has blown or if a circuit breaker  
has tripped.  
Ingredients will not mix  
properly  
• Check to see if enough liquid has been added to the ingredients. Mixture should  
be fluid and free-running at all times.  
• Solid pieces are too large. Pieces should not exceed 1" cubes.  
• Container is too full. Do not fill past highest graduation marking.  
• Cutter unit blades are not sharp or are damaged. Inspect  
container and cutter assembly daily. Replace container and  
cutter assembly at least every 12 months or sooner if cutter assembly appears  
worn or damaged.  
• Check to see if cutter assembly is installed properly.  
• Select speed to create a fluid blend.  
Maintenance  
Inspect the blender and its various parts and replace as follows:  
Daily  
Unplug the blender and remove the container from the base, and then inspect the  
container and cutter unit assembly for wear, nicks, and broken or loose blades. Replace if  
necessary. If the blades are loose, discontinue use immediately and replace the blades.  
Do not attempt to repair or tighten the cutter assembly. See “Replacement Parts” below.  
Weekly  
Yearly  
Unplug the blender, and then inspect the power cord insulation and power plug for cracks.  
Refer to “Requesting Assistance or Service” for repair or replacement.  
Replace the container and cutter assembly at least once a year.  
See “Replacement Parts” below.  
Replacement Parts  
Refer to “Requesting Assistance or Service” to order parts below.  
Model  
Part Description  
Part Number  
1G91300  
1G91300  
1 container  
6126-91300  
99200  
Cutter assembly  
261 Yadkin Road  
Southern Pines, NC 28387  
840083701-UK  
12/03  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Drill T21321 User Manual
Grizzly Saw G0503 User Manual
Haier Refrigerator HVC15 User Manual
Haier Water Heater FCD JTSA50 III User Manual
Honeywell Scanner MS7600 User Manual
Hotpoint Cooktop HUE User Manual
Hypertec Mouse 260 PS 2 User Manual
iHome CD Player iA100 User Manual
Iluv Stereo System i277 User Manual
Image Home Gym IMBE41990 User Manual