Haier Washer XPB10 LAP User Manual

Safety precautions  
Please insert the power cord into  
special receptacle with rated vol-  
tage.Be sure to use single-phase  
three pins receptacle.The earthing  
terminal of the receptacle must be  
earthed reliably.If possible,please  
adopt electric leakage protector.  
When the machine is normally  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned or when it  
is idle.  
Twin-tub Washing Machine  
User's manual  
Earth  
If the power cord is bad, to avoid risk it is required to replace it by the  
technicians ofour special shop or the after-sale service department.  
Keep the pin of the power plug clean.  
Do not put the machine at damp  
Do not use water hotter than 50 C .  
This manual is for  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
In case the washing machine is installed  
on ground with carpet , do not block the  
ventilation hole with carpet.  
Ventilation hole at  
the bottom of the  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Please read this manual  
carefully before using.  
washing machine  
Retain it for future reference.  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety precautions  
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not decompose, repair or alter the  
machine by yourself.  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
Petrol  
inner  
Th  
Pay attention to followings before washing the laundries  
Check if  
The quantity of  
When the pulsator  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
the laundries is running , the  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Handicapped or children without care  
shall not use the machine.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
To protect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
6
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and adjustment  
Please install and adjust the machine according to the requirement of  
the manual. It is very important to your security and correct operating  
the machine.  
How to change the direction of the drain hoses  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
Usage of the drain hose  
Back  
Front  
The drainage shall be smooth with the drain hose.  
3 If the drain hose is too long, cut it at mid  
Soft item  
1.The height of the drain hose shall be  
point. To make smooth drainage, cut the  
less than 10cm , or the drainage will  
front end of the hose slantingly.  
Extend the drain hose from the side of spin tub  
not be smooth enough and cause  
incomplete drainage.  
Figure 1  
Put soft items on the ground. Lean the machine  
down gently with the front surface facing the  
ground. Take off the drain hose from the cabinet.  
Dismantle the drain hose fixing clamp and take  
the hose out of the fixing groove.  
(See to Figure 2).  
<10cm  
4.If extra drain hose is needed , the inner  
diameter of the extra hose shall not less  
Drain hose fixing clamp  
2.Do not step on or press the drain hose.  
than 30mm, and the length shall not exceed  
1.5m.  
>
30mm  
<1.5m  
Soft item  
Figure 2  
Embed the drain hose into the groove along the side  
of the spin tub in the order of (1)~(3), heading for the  
side of the spin tub. (See to Figure 3).  
Install the lint filter  
overflow filter  
lint filter  
After openning the package,please take out the lint  
filter from the document bag,install it to the filter frame  
of the cabinet.See to the figure.  
Extend to the  
spin tub side  
Install the water inlet hose; Select the water level  
Embed into the  
groove in turn  
Embed the drain hose into the groove with  
hands. Take care not to damage the drain  
hose in fastening the fixing clamp.  
Use the new water inlet hose provided with the  
machine to connect to the water faucet.  
Old hose sets should not be reused.  
Figure 3  
Water-filling  
entrance cover  
Water inlet hose  
Water-filling  
entrance  
Insert the water inlet hose into the water-filling  
entrance on the control panel directly. (pull it  
out to dismantle it)  
Extend the drain hose from the rear side  
Select water level according to the  
quantity of the laundries.  
Dismantle the drain hose fixing clamp.  
Take out the drain hose from the fixing groove.  
Extend it from the rear side as per the direction  
of the arrow. (When the drain hose is extended  
from the rear side, it can be hung on the point  
for drain hose at the two sides of the cabinet.)  
(See to Figure 4).  
Attention:  
Max  
Med  
Maximum  
In water filling, do not exceed  
the"Maximum" water level. Otherwise  
the water may overflow out of the  
washing machine.  
Figure 4  
Medium  
Minimum  
Min  
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
The musts in washing  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time. Laundries  
quantity in one washing cycle shall be lower  
than the rated capacity. The largest  
capacity of this machine is 10kg.  
Rinsing  
(Repeat the midway spinning and  
rinsing with stored water for 2-3 times)  
Rinse with stored water  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
Do not select " Max " water level for  
laundries less than 4.0kg, so as to avoid  
splashing of water.  
It is suggested not to use high sudsingdetergent.  
2. Fill water to preset water level.  
Usage of the detergent  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
How to use the whitener  
How to use the washing powder  
When the laundries quantity is below 4.0 kg, please use "Standard" current.  
If you use "Strong" current, it may splash.  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30  
seconds to dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
If the water flows out from the overflow holes, it means that water filling  
quantity is too much.  
Fill water to decided level. Dilute  
the whitener with container.  
Pour it slowly into thewashing tub.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
OVERFLOW  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 C and a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
If the water flows out of the  
overfill holes, that is over-  
filling, please twist the  
water tap to limit the water  
filling, to avoid influencing  
the life of the machine.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
7
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Washing sequence  
Water-filling selector  
Wash timer  
(To set to below 2 minute,  
first set to minute then  
turn it back. It can increase  
the service life of the timer).  
Water inlet  
entrance  
Wash selector  
(standard current,  
strong current)  
Spin timer  
(To set to below 1 minute,  
first set to minute then  
turn it back. It can increase  
the service life of the timer).  
Midway spinning  
5
2
1.Put the laundries into the spin tub evenly and smoothly.  
OFF  
15  
OFF  
5
3
1
2.Spin  
12  
4
6
2
(1) Put the gland in properly.  
3
9
Please put in the gland properly even if the laundries quantity is small.  
Gland  
Push  
Push  
Wash  
1.Water-filling selector  
Set the water inlet selector at the "WASH" side.  
(Figure 1)  
WASH SPIN  
The laundries  
are slanting  
Figure 1  
Proper  
Proper  
No gland  
(2) Close the inner and outer cover of the spin tub.  
2. Fill the water and add the dissolved washing  
powder to make the water level reach the preset  
position. (Figure 2)  
Outer cover of  
The spin tub  
Run washing program for some time to stir and  
dissolve the powder completely.  
Figure 2  
Figure 3  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Put in the laundries. If the water quantity is  
insufficient, please add water.  
3.Run the foam-removing spinning.  
(1) Open the outer cover of the spin tub.  
(2) Set the water-filling selector control  
rod at the "SPIN" side. Fill water for  
about 1 minute.  
4.Select the current.  
Select the strength of the current according to  
the laundries. (Figure 3)  
WASH SPIN  
OFF  
15  
3
Figure 4  
If the water quantity filled is too large,  
the water may flow out from the wash  
tub side. Please twist the water tap to  
limit the water filling.  
5.Select the washing time  
Select the washing time according to the laundries.  
(Figure 4)  
12  
6
9
(3) Close the outer cover of the spin tub.  
Spin for 1-2 minutes.  
6.After washing, Set the "WASH SELECTOR" at  
"DRAIN" in order to discharge the water. (Figure 5).  
Figure 5  
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 1).  
Water level  
adjusting lever  
Cleaning the lint filter  
Corrugation  
Pipe  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
1. Press the elastic piece at upper end of lint filter to  
release the tab from the filter cover, and pull the lint  
filter outward to remove it. (See Figure 1).  
Figure 1  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Figure 1  
2. Remove lint  
Hook  
Pull the lower end of lint filter rear cover outward  
to disassemble it from the lint filter front cover.  
Remove lint completely with clear water. (See  
Figure 2).  
Lint filter rear cover  
(3).Hang up the hook at the left  
upper side.  
(4).Push the upper part in as  
indicated in Figure 2.  
Disassemble  
Figure 2  
Assemble  
Lint filter frontcover  
3. Install lint filter  
Disposal of the complete unit  
Page 4  
Figure 2  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe the complete unit with soft  
cloth twisted dry.  
Wipe with neutral detergent if too dirty  
Do not wash it directly by water  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
Elastic fixing  
claw  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
1
Take off the overflow filter.  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
13  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Spinning  
Selection of the spin time list 3  
Spin time  
1. Put the laundries into the spin tub  
evenly and smoothly.  
Phenomena  
The reason  
Laundries  
(minutes)  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
The machine does not act.  
Bed sheet or  
About 4~5  
blanket  
2. Press the gland in the tub properly.  
Close the inner and outer cover of  
the spin tub.  
Is the drain hose put down?  
Is the drain hose frozen?  
Is the drain hose blocked by foreign material?  
Underwear  
About 2~4  
(knitwear)  
The draining does not work  
Swear  
(chemical fiber)  
About 1~2  
3. Spin  
There's abnormal sound  
during washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
Select suitable spin time according  
to the laundries, and do spinning.  
Blending thin  
Within 1 minute  
laundries  
There's abnormal sound  
and violent vibration  
during spinning  
Is the machine slanting?  
Is the gland pressed evenly?  
Are the laundries in spin tub too much?  
During spinning, if there's abnormal  
sound, it is generally owing to slanting  
placement of the laundries. Please  
stop the machine and re-order the  
laundries.  
There may be some water  
flowing out of the drain  
hose in the first use of  
the machine.  
It is the water remained in the factory inspection  
of performance.  
In spinning, it will pause the work if you open the outer cover of the spin  
tub. Close it to resume the spinning.  
When the remained water is frozen  
Prevent the freezing (be sure to discharge the water completely after using)  
After complete draining, set the "WASH SELECTOR" at "STRONG" or "STANDARD".  
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.  
To do spinning and draining together,  
please first do spinning for around 1  
minute, then do draining. Otherwise  
the spinning will stop owing to too much  
water stored in the spin tub.  
When the water is frozen  
Below  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
11  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Quantity  
Name  
One piece  
User's manual  
One piece  
Water inlet hose  
One piece  
One set  
Gland  
Twin-tub washing machine  
Specification  
Water level/Water quantity (about)  
Maximum/99L Medium/77L Minimum/65L  
0.02 0.2  
Injection pressure(MPa)  
Washing / Spinning capacity(kg)  
10/7.0(weight of standard dry cloth)  
15  
Special number:0030804130A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Gravely Lawn Mower 985114 16 HP User Manual
Haier Washer Dryer HWDC1000TXVE User Manual
Healthrider Treadmill HMTL796080 User Manual
Heat Glo LifeStyle Indoor Fireplace EXCLAIM 42H C User Manual
Honeywell Home Safety Product HMR4007 User Manual
Hotpoint Dishwasher FDM 550 User Manual
HP Hewlett Packard Projection Television 7550e User Manual
Husqvarna Lawn Mower 36 EL User Manual
Husqvarna Lawn Mower 43EL 43ELS User Manual
Impex Home Gym MD 3400 User Manual