Haier Washer HWM70 A User Manual

HWM70-A  
Fuzzy Computeried Automatic  
Washing Machine  
Contents  
Before using  
Names of the parts The 2nd cover  
Safety precautions  
1
3
5
Installation and adjustment  
Install the water inlet hose  
Using process  
Preparation before washing  
Put in the laundries  
7
8
Add the detergent and softener  
Use the operation buttons  
Close the top lid  
9
10  
14  
14  
15  
Finish washing  
Please read this manual carefully before using.  
Retain it for future reference  
Disposal after washing  
Trouble shooting *  
Answers to questions  
16  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
17  
Picking list  
The manufacturer will not bear the responsibility for  
those risks occurred from not obeying this manual.  
Specifications  
the back cover  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
In normal usage of the washing machine,  
the power plug shall be ready to be pulled  
or plugged with hand. Be sure to pull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
cleaning the machine. Do not plug  
or pull the power plug with wet hand.  
Please insert the power cord into special  
receptacle with rated voltage.Be sure to  
use single-phase three pins receptacle.  
The earthing terminal must be earthed  
reliably.If possible,please adopt electric  
leakage protector.  
Earth  
Do not bend, stretch, twist, bind the power cord by force,  
or reform it. Do not press or clamp it with heavy items. If the  
power cord and power plug are bad, or the receptacle is loose,  
be sure to have it replaced by the technicians of our special shop  
or our agent, or the after-sale service department for the sake  
of avoiding any risk. Keep the prong of the power plug clean.  
If dust is found on the power plug, please wipe it off with dry cloth.  
In case the washing machine is installed on  
ground with carpet, be careful not to block the  
ventilation hole with carpet.  
Do not use water with temperature  
higher than 50 inside the tub.  
The ventilation  
holes at the  
bottom  
Do not set the machine atdamp place  
like the bathroom. Never wash it with water.  
Do not put wet laundries on the control  
panel coating.  
Do not wash water-proof laundries like  
the raincoat, bikecovers, down textiles etc.  
to avoid abnormal vibrations in spinning and  
damaging the laundries.  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or the  
plugging into the receptacle is loose, do not use it any  
more.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
Do not put hand into the rotating tub. It is  
dangerous even if the rotation speed is slow.  
Take special care of the children. Keep  
children away from the washing machine  
to avoid them climbing on it.  
Do not decompose, repair or alter  
the machine by yourself.  
Do not put any hot or heavy items  
(such as the kettle with hot water) on the  
washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
Keep the machine away from direct  
sunlight and heat source like the heater.  
The handicapped or children shall not  
use the machine without care.  
To prevent the lint in the tub from blocking  
the cascade outlet and influencing the  
cascade effect, please keep the lint filter  
in good condition, and install it to proper  
position during washing. If the lint filter is  
lost or damaged, please contact the local  
after-sale service department of our  
company.  
Toprotect your laundries and washing  
machine, please take out all of the coins,  
buttons, sand, hairpin and other foreign  
materials before washing.  
Please check if the water faucet is open, and if  
the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
Please install and adjust the machine according to the requirement of the manual, which is very  
important for you to operate the machine safely and properly.  
Install the bottom plate  
After opening the package, please lean the  
washing machine gently down on soft items  
(like towel cloth, blanket, etc.). Install the  
bottom plate to the bottom of the machine  
with eight screws by a cross screwdriver,  
then lift the machine up gently. See to the  
figure:  
Back  
Front  
Soft item  
Bottom plate  
Screw  
Adjust the installation position  
The largest allowable slope of the shank base  
of the machine is 2 . The slanting or rough  
ground will result in unstable running or  
stoppage of the machine. Please adjust it with  
following methods:  
Confirm it's horizontal:  
Air bubble  
If the bulb of the level meter at the balance display  
position is inside the standard circle, it indicates that  
the machine is horizontal. Otherwise you need to  
adjust the adjustable leg of the machine.  
Suitable  
Not suitable  
Standard circle  
Adjust the adjustable leg:  
1.To twist the adjustable leg, please first lift up the  
leg side slightly, loosen the adjustable nut, and  
then twist the leg.  
Adjustable nut  
Fasten  
Adjustable leg  
Loosen  
High  
2.After adjustment, fasten the nut.  
Low  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Beforee using  
Install the lint filter  
After opening the package, please takeout the lint  
filter from the document bag, install it to the filter cover  
of inner tub. See to the figure.  
Inner tub  
Lint filter  
How to change the direction of the drain hose  
4.Dismount the protecting cover of the drain outlet at the other  
side as indicated in Figure 3.  
5.Extend the drain hose out of the other side. Fix the drain  
hose onto the cabinet with the drain hose rack. Set the  
drain hose nut on, and fasten the nut to the direction  
indicated in the figure, as per Figure 4.  
1.Dismount the back cover of thewashing machine.  
2.Lay down the washing machine gently with thefront side  
facing the ground. Use cross screwdriver to loosen the  
eight screws. Take offthe bottom plate.  
back  
bottom plate  
drain outlet  
protecting  
cover  
front  
soft item  
fasten  
3.Put down the outer drain hose.Twist thedrain hose nut  
Figure 3  
Figure 4  
counterclockwise to take it off asindicated in Figure 1.  
Take off the drain hose rack.Put the drain hose into  
the cabinet as indicated in Figure 2.  
6.Install the protecting cover of the drain outlet to the other side,  
as indicated in Figure 5.  
Loosen  
Figure 5  
Outer  
drain hose  
7.Install the bottom plate (method the  
same as stated above). Lift up the  
washing machine gently.  
Drain hose nut  
Drain hose rack  
Figure 2  
drain hose nut  
Page 3  
Figure 1  
Usage of the drain hose  
The drain hose shall drain smoothly  
1.The height of the drain hose shall be  
less than 10cm, or the drainage will not  
be smooth, and cost such long time that  
the machine may stop at mid way.  
4.If extra drain hose is needed, please  
make separate purchase. The inner  
diameter of the extra hose shall not  
less than 30mm, and the length shall  
not exceed 1.5m.  
2.Do not ramp or press the drain hose.  
If the drain hose is too long, cut it at mid  
point. To make smooth drainage, cut the  
front end of the hose slantingly.  
If the extra hose is too long, cut it  
either at A or at B point.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Install the water inlet hose  
Install the water inlet pipe  
Water faucet, suitable  
water faucet, not suitable  
It is required that the front end shall be longer than 10mm.  
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.  
Connection between the water inlet hose jointer and the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose  
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four  
screws and take out the bush inside the jointer. See to Figure 3.  
Water inlet hose jointer  
Screw  
Slider  
Nameplate  
Bushing  
Screw knife  
Lock level  
Water inlet hose  
Figure 1  
Figure 2  
Figure 3  
3 Fasten the four screws of the water inlet hose jointer evenly. See to Figure 4.  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut..  
About 4mm after twisting  
About above 2mm after twisting  
Screw nut  
Figure 4  
Figure 5  
Figure 6  
Connection between the water inlet hose and the washing machine  
1 Do nottake off the water absorptioncushion. Please check  
if the cushionis dropped ordamaged each timebefore using.  
If it happensso, please dulycontact our after-sale service  
department.  
Water inlet  
hose nut  
2 Set thenut of thewater inlet hoseon the waterinlet valve jointer.  
3 Fasten thenut. Swing itgently to confirmif it's fastenedwell.  
Water absorption cushion.  
Water inlet valve jointer  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Connection between the water inlet hose jointer and the water inlet hose  
1 Push down the slider. Plug the water inlet hose into the jointer.  
The water inlet  
hose jointer  
2 Hang the lock lever onto the jointer. Release  
the slider till a click sound is heard.  
Slider  
Locking level  
Check the connection between the water inlet hose jointer and the  
water faucet  
1.Swing the hosegently to checkif it isfastened stably.  
2.After installation, openthe faucet tocheck if it leaks water.  
3.Do not bendthe hose byforce.  
4.Each time beforeusing, please checkif the connection  
between the waterinlet hose jointerand the waterfaucet,  
and the installation of the waterinlet hoseis firm, so as  
to avoid droppingowing to improperinstallation.  
Dismount the water inlet hose  
1 Close the water faucet.  
2 Press the lock lever and push down the slider. Then pull off the  
water inlet hose. If the machine is used more than once every  
week, the water inlet hose jointer can remain on the faucet to  
avoid damaging the fastening screws.  
Lock level  
Slider  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
1Preparation before washing  
Preparation before washing  
1 Connect the water inlet hose. Open the water faucet.  
2 Confirm that the washing machine is earthed reliably.  
Then plug the power plug into the receptacle. The  
earthing terminal shall not link to gas pipeline and  
faucet water pipeline.  
3 Put down the drain hose.  
Earth  
Pay attention to the followings before washing  
Check  
if C l e a r t h e Tie the long The quantity of  
When the pulsator  
the laundries pocket. Take strips; fasten the laundries is running ,the  
have special out the coins, the buttons; shall not be too buttons of the  
requirement sand, hairpins close zippers. large. Stretch laundries may  
on washing etc.  
and loosen the cause noise. For  
laundries before t h e s a k e o f  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
A. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put the laundries difficult to absorb water into water with hand.  
d. For the laundries with heavy soil, please first remove the dirt like mud or dust.  
For the parts with heavy soil, please apply detergent on them in advance, which  
can make it easier to remove the soil.  
e. For the laundries that may get lint ball and those with long fur, turn it over before  
putting in.  
f. Do not put the laundries polluted by chemicals into the washing machine directly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
2 Put in the laundries  
The capacity of washing and spinning refer to the  
largest weight of the standard laundries under dry  
condition that can be washed or spinned in one  
cycle. Washing quantity for one cycle shall be  
less than the rated capacity.The largest capacity of  
this machine is 7.0kg.  
The thickness, size and type of the cloth will  
influence the actual washing capacity. It is  
feasible to put in suitable amount of laundries and  
the laundries can be tumbled normally in washing  
for one cycle.  
Please do not select high water level for laundries  
less than 2.5kg to avoid splashing.  
In washing the fluffy laundries like the woolen  
blanket, the quantity shall not exceed 3kg for  
each cycle.  
In using water with high temperature, please pay  
attention to the washing temperature limit stated  
on the label of the laundries.  
Reference weight of the laundries:  
Working suit up,down  
cotton,about 1120g  
Jeans about 800g  
Blanket  
cotton,about 900g  
blending coat  
about 800g  
Pajamas  
about 200g  
Jacket  
cotton,about  
800g  
Shirt  
cotton,about  
300g  
Single bed sheet  
cotton,about 600g  
Undershirt  
cotton,about 180g  
Socking  
blending,about 50g  
Underpants  
cotton,about 70g  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
3 Add the detergent and softener  
Put the washing powder and softener into the detergent  
box directly as indicated in the left figure.  
After that, please close the detergent box. Refer to the  
following table for the usage of the detergent: The  
standard dosage of the detergent and the water  
quantity  
Inlet for concentrated washing  
powder and detergent  
Softener inlet  
How to use the washing powder  
Not applicable for fuzzy program and reserve  
washing  
Directly dissolved in the machine:  
Detergent box  
1.Fill in small quantity of water.  
2.Add the washing powder. Run for 30 seconds  
to dissolve it completely.  
How to use the whitener  
3.Put in the laundries. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 and a container.  
2.Add the powder into the container while  
stirring to fully dissolve it.  
The powder is more likely to pollute the laundries  
than the detergent. Therefore please use it with  
suitable quantity.  
Fill water to decided level. Dilute the  
whitener with container. Pour it slowly into  
the washing tub.  
Do not use whitener on laundries with  
color or print as they are not colorfast.  
The whitener shall not touch the laundries  
directly.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or long time  
storage may be caked. Please pay attention to  
cleaning the detergent box in time.  
Refer to the user's manual for the usage  
and dosage of the whitener.  
As to whitener in powder, please dissolve  
it before using.  
Standard dosage of the detergent and water quantity  
Laundries  
Common powder,  
Concentrated powder,  
Water  
quantity  
Water  
level  
quantity  
(kg)  
Add 40g in each 30L water Add 25g in each 30L water  
About 66L  
About 61L  
About 88g  
About 81.3g  
About 55g  
About 50.8g  
About 57L  
About 53L  
About 76g  
About 70.7g  
About 47.5g  
About 44g  
About 49L  
About 44L  
About 65.3g  
About 58.7g  
About 40.8g  
About 36.6g  
About 40L  
About 34L  
About 53.3g  
About 45.3g  
About 33.3g  
About 28.3g  
About 30L  
About 23L  
About 40g  
About 30.7g  
About 25g  
About 19g  
Below 1.0  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
4 Use the operation buttons  
a Description of the function of the operation buttons  
button  
WATER INLET  
Mode and meaning of the indicator  
In starting themachine, it isset to COOL  
WATER automatically  
Flash: indicating the running mode  
Push the buttonto select onefrom the three  
modes of COOLWATER only, both WARM  
WATER and COOL WATER, or hot wateronly.  
Note that thewater temperature insidethe  
On: indicating the mode about to run  
Flash rapidly: indicating abnormal situation  
tub shall notexceed 50  
.
Balance display  
Cool water No requirement on water temperature  
If the bulb of the level meter is inside the standard circle, it indicates  
that the machine is horizontal.  
If the hot water temperature is too high  
and needs to be mixed with cool water  
Cool water  
Warm water  
When the temperature of hot water is  
suitable, or when you need to improve  
the water temperature inside the tub  
Warm water  
Balance display  
STRONG  
COOL  
WATER  
INLET  
WATER  
LEVEL  
CURRENT  
button  
TER LEVEL  
WA  
Select the fuzzy program. After clothdetection, the water  
level will beset to oneout of 4, 6, 8, and10.  
If there's water inside the tub, the machine cannot detect  
the cloth andwill display water level 6  
If wet laundries are putin, it maydisplay water level 10  
You can also set water level by self. After themachine is  
started, it will not detectthe cloth.  
CURRENT button  
When the washingmachine starts running, it  
will set thecurrent automatically.  
If quick program is selected, the waterlevel will beset to 2  
automatically. When level is reached, itwill perform  
washing while filling water. The 2 water level indicator is  
on, and the4 water level indicator isflashing. When the “4”  
water level isreached, it will stop fillingwater. 2level  
indicator is off, and 4 level indicator is on. It will perform  
normal washing.  
You can select currentby self accordingto the  
actual requirement.  
Please do notselect strong currentunder low  
water level toavoid splashing andvibration.  
In FASTand GENTLE programs, the washing  
machine will setthe current automatically, and  
the users cannotselect current inthat case.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
START/PAUSE button  
Digitron  
During sensing, it displays --  
During operation of programs, it displays the  
remained time (minute)  
During reserve procedure, it displays the  
remained reserve time (in hour)  
After the poweris switched on, push it to start  
the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
In case of abnormal phenomenon, it displays  
the abnormal symbol (see to Page 16)  
POWER ON/OFF button  
Push the On/Off button toswitch on the power.  
When the poweris on, push it again to switch  
off the power.  
FUZZY  
SOAK  
WASH  
RINSE  
SPIN  
STANDARD  
NIGHT  
POWER  
ON/OFF  
SURPLUS  
GENTLE  
FAST  
RESERVE  
HOURS LATER  
START  
PAUSE  
SELECT  
PROGRAM  
RESERVE  
SELECT button  
Push it to select one or more programs from SOAK  
WASH RINSE and SPIN  
PROGRAM button  
The following four programs are available for your  
option  
button  
RESERVE  
Push the buttonto select washing finishing  
time between 2-24 hours.  
Standard Common washing  
When the RESERVE function is activated, the  
RESERVE and TIME REMAIN indicators are  
on. The other indicators are off.  
Push the RESERVE button todisplay the  
reserve mode.  
Night  
Low noise washing during night  
Gentle  
FAST  
Washing the woolen textiles or underwear  
10-minute quick washing of laundries with light soil  
Remarks: Push theOn/Off button to switch onthe power. If the washingmachine is idlefor 5 minutes, it will automatically  
switch off the power.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Using process  
B Steps of using the operation buttons and description of each step.  
BALANCE DISPLAY  
FUZZY  
STRONG  
SOAK  
WASH  
RINSE  
SPIN  
STANDARD  
POWER  
ON/OFF  
COOL  
NIGHT  
GENTLE  
FAST  
MIN  
SURPLUS  
WARM  
RESERVE  
HOURS LATER  
SOFT  
START  
PAUSE  
WATER  
INLET  
WATER  
LEVEL  
SELECT  
PROGRAM  
CURRENT  
RESERVE  
POWER  
ON/OFF  
1 Push the POWER ON/OFF button to switch on the power.  
2 Push the program button to select suitable automatic program.  
After switching onthe power, the machine willset standard programautomatically. To select otherautomatic program,  
push the PROGRAMbutton till therelative indicator ison.  
Refer to thePROGRAM button onPage 11 for theselection.  
Page 11  
For instance: selectQUICK program forlaundries with smallquantity and lightsoil.  
FUZZY  
STANDARD  
In selecting the standard and night programs, the  
machine will execute fuzzy program to select  
water level and wash time according to the cloth  
and weight ofthe laundries. The full procedure is  
controlled automatically.  
NIGHT  
PROGRAM  
GENTLE  
FAST  
SELECT  
3 Push the select button to select suitable procedure.  
After switching on the power, the washing machine will set to WASH-SPIN procedure  
automatically. It is the common procedure. To select other procedures, push the SELECTbutton to  
select one or more procedures from SOAK, WASH, RINSE ANDSPIN. Refer toPROCEDURE  
SELECTION METHOD tomake selection.  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Using process  
Attention  
Even there's no water in the tub, a certain period  
is required before spin starting.  
Do not use the SOAK program for the woolen  
textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
Procedure selection method  
Times of pushing the  
SELECT button  
Contents (the lightedindicators  
indicate the programs about to run)  
Selected procedure  
Applicable circumstance  
When the common laundries need  
washing, rinsing and spinning.  
WASH - SPIN  
SOAK WASH RINSE SPIN  
WASH  
(the washing liquid  
remains in the tub)  
SOAK WASH RINSE SPIN  
SOAK WASH RINSE SPIN  
SOAK WASH RINSE SPIN  
SOAK WASH RINSE SPIN  
SOAK WASH RINSE SPIN  
Repeat using the washing liquid  
When prevent the laundries from  
corrugating, and the laundries do not  
need spinning  
WASH - RINSE  
(the rinsing liquid  
remains in the tub)  
When the laundries need rinsing  
and spinning after manual washing  
RINSE - SPIN  
When the laundries need only  
spinning after manual washing (first  
drain then spin)  
Spin  
(spin after drain)  
The laundries are very dirty, or the  
sleeves and collars of the shirt are  
very dirty. First soak then wash.  
SOAK - SPIN  
Push the SELECT button for 6 times, and it will resume the initial mode. It will circulate in that sequence.  
The SOAK procedure can work in cooperation with automatic programs like standard and night. There is  
intermittent pulsator stirring during soak.  
4 Push the WATER INLET button to select water inlet mode  
After the power is switched on, the washing machine will set to COOL WATER inlet mode automatically. To  
select WARM WATER only or both COOL WATER and WARM WATER, push the WATER INLET button to make  
selection. See to WATER INLET in Page 10 for details.  
Page 10  
WATER  
LEVEL  
5 Push the WATER LEVEL button to select suitable water level  
After the poweris switched on, the washing machine will execute fuzzy program automatically to detect the cloth. After  
defection, it can set the waterlevel automatically. To select other water level, push the WATER LEVEL button to setthe  
water level. Referto STANDARD DOSAGE OFDETERGENT AND WATER QUANTITY in Page 9 and WATER LEVEL in  
Page 10 forselection.  
Page 9  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Using process  
Water Level and Time Table of Each Program  
Spin  
(minute)  
Total time (minute)  
Soak included Soak excluded  
Wash  
(minute)  
Water  
level  
Rinse (minute)  
Program  
Standard  
Rinse twice  
Spray twice,  
rinse once  
Rinse once  
Rinse once  
About 83~45 About 48~30  
About 99~55 About 65~40  
About 5~6  
About 6~8  
Night  
About 2  
About 2  
Gentle  
Fast  
About 21~17  
About 10  
About 4  
About 3  
* Total time: including the normal water inlet time and drain time.  
* Wash time: adjustable according to the water temperature automatically.  
* Spin time: the time from intermittent running to finishing  
* The standard and night programs can have SOAK procedure. After water inlet, it will first perform soaking  
for about 15-35 minutes along with slightly pulsator stirring, and then do washing.  
* The washing finishing time may be influenced by the water inlet pressure.  
6 Push the CURRENT button to select suitable water current  
After the poweris switched on, the washing machine can set the current automatically according to the laundries. If you  
need to select current by yourself, please push the CURRENT button.  
Page 10  
Refer to CURRENTin Page 10 for details.  
RESERVE  
7 Push the RESERVE button to select suitable reserve wash program  
After the poweris switched on, the reserve program is set to off mode automatically. If you need to set the washing  
procedure to be finished at reserved time, please push the RESERVE button to set the reserve wash program. Refer to  
RESERVE BUTTON in Page 11 for selection.  
Reserve time from 2 to 24 hours  
Confirm the operationof reserve program  
When the RESERVE function is activated, the indicator of the program you have set will be  
off. The RESERVE (HOUR) and TIME REMAIN indicators will be on. During reserve  
procedure, you can push the RESERVE button to display the reserve mode.  
To change the running program or cancel the reserve setting, you need to switch off the  
power and make new selection.  
The washing will be finished after 18 hours.  
START  
PAUSE  
8 Push the START/PAUSE button  
5 Close the top lid. 6 The washing is finished.  
It beeps to indicate the  
finishing of washing  
If you open the top lid, the machine will stop working before spinning.  
The power will be switched off automatically after the finishing of the washing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Using process  
7 Disposal After Washing  
Please take off the detergentbox and washit with water  
1.How to takeit off: Pull it upwardsslantingly and gently.  
2.How to install:Put it infrom the topslantingly, then push  
it in to the right position.  
Lint filter:  
1.Pull it up to dismount.  
2.Push it downto install it.  
3.After washing, cleanthe filter screen  
Dismount  
Install  
Dismount and install  
Clean  
The filter screenis likely to be blocked by foreign  
materials and influence water inlet. Pleaseclean it  
with brush frequently.  
If the cabinet is dirty, wipe it with wet soft cloth  
Do not wash with water directly.  
Wipe with neutral detergent.  
Do not wipe with thinner, petrol, alcohol, etc.  
1.After washing, close the water faucet. (If desired, dismount the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely  
after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid  
for some time (about 1 hour), then close the top lid.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble--shoootingAAnsweers to qquestions  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Phenomenon  
Reason  
How to solve  
It rings afterstarting the reserve  
function. The digitron displays E0.  
The top lid is opened.  
Close the top lid.  
Clean the foreign material. Push  
the start button again.  
The drainage cannot work, or is too slow.  
The digitron displays E1 and it rings.  
Is the drain hose blocked?  
After washing andrinsing, it stops  
running during spinning. The  
digitron displays E2and it rings.  
The top lid is not closed.  
Close the top lid.  
The safety switch acts, and the  
spinning cannot work (after twice  
automatic imbalance revising). The  
digitron displays E3 and it rings.  
Reorder the laundries. Close the top lid.  
Set the washing machine horizontally and  
then open and close the top lid once.  
Are the laundries put slantingly?  
Is the machine slanting?  
Open the water faucet. Push the  
Start/Pause button again.  
Clean the water inlet valve then push the  
Start/Pause button again.  
The water inletdoes not work, or is  
too slow (cannotreach the water  
level after about15 minutes). The  
digitron displays E4and it rings.  
Is the water faucet opened, or is  
there water supply failure?  
Is the water inlet valve blocked?  
The water temperature is too high.  
The digital tube displays E5, and rings.  
The temperature ishigher  
than 60 C.  
After cooling. Pressthe Star/Pause knob.  
Clear the foreign material.  
Is there foreign material blocking  
the spray outlet?  
The cascade currentis poor or  
there's no cascadecurrent.  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset  
position?  
Not wash  
The machine  
does not act.  
Insert the powerplug tightly.  
Close the toplid.  
Set the laundriesflat.  
Adjust the machine to be even  
Remove the foreign materials.  
Reorder the laundries and close the top lid.  
Is the powerplug inserted tightly?  
Is the toplid closed reliably?  
Are the laundriesset flat?  
Is the machine slanting?  
Are there any foreign materials?  
Are the laundries put slantingly in  
spinning?  
Not spin  
There's abnormal soundinside  
the machine  
Is the screw of the water inlet hose  
jointer loose?  
Fasten the screw of the jointer properly.  
The water faucetleaks water  
Is the screw of the water inlet hose  
jointer twisted awry?  
Is the power plug plugged tightly?  
Is the water faucet opened?  
Are the POWER ON/OFF and  
Plug the powerplug tightly.  
Open the waterfaucet.  
Push the powerON/OFF button and  
START/PAUSE button.  
No water inlet.  
START/PAUSE buttons pushed down?  
Common phenomena  
Phenomena  
Explanation  
The spinning is intermittent whenit starts.  
The wash procedure pauses.  
It is tobalance the laundriesto avoid slanting.  
The cloth sensoris detecting thecloth. It willstart  
adding water afterabout 48 seconds.  
The program is setting thedrain time. A certain  
period is neededbefore it startsspinning.  
Push the SPINbutton, but it doesn't act.  
The pulsator pauses during water filling in washing and rinsing.  
It is toavoid splashing duringwater filling.  
It is thewater remained inthe machine duringthe  
ex-factory performance inspection.  
There may be some waterflowing out ofthe drain  
hose in thefirst use ofthe machine.  
It is tosoak the laundriesmore completely.  
In adding water, the pulsatorperforms stirring slightly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Quantity  
Name  
Storage position  
1 piece  
1 piece  
2 pieces  
Inside the document bag  
Inside the document bag  
User's manual  
Lint filter  
Water inlet hose component  
Inside the accessory bag  
Between the upper cushion of the  
washing machine package and the upper  
seal of the package carton  
1 piece  
Bottom plate  
Inside the accessory bag  
8 pieces  
1 set  
Tapping screw  
Fuzzy logic automatic  
washing machine  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
HWM70-A  
Rated voltage frequency  
Rated washing / spinning capacity  
220V ~ 60Hz  
7.0kg  
1/23L, 2/30L, 3/34L, 4/40L, 5/44L,  
Water level/Water  
quantity (about)  
6/49L, 7/53L, 8/57L, 9/61L, 10/66L  
Max water consumption  
Water inlet pressure  
About 186L (the highest water level, standard program)  
0.03MPa-0.78MPa (when water temperature is  
70 ~90 , the water inlet pressure of hot water  
shall not exceed 0.4MPa)  
Rated washing power  
Rated spinning power  
Weight  
400W  
240W  
About 38kg  
L 610 W 555 H 945  
Dimensions (mm)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Hakuba Projector Accessories PMD1 User Manual
Heat Glo LifeStyle Indoor Fireplace AT GRAND D User Manual
Honeywell Thermostat TL8130A User Manual
Hotpoint Washer Dryer WMA40 User Manual
HP Hewlett Packard Computer Drive MSA50 User Manual
HP Hewlett Packard Grinder 39 1572 User Manual
HP Hewlett Packard Printer 1000C User Manual
HP Hewlett Packard Switch 331404 008 User Manual
HP Hewlett Packard Tablet D3H85UTABA User Manual
ICP DAS USA Camcorder IM 100 User Manual